Horizontal centrifugal casting is an effective method for the production of hollow metal with good mechanical properties, low defect, cast

to size and relatively cheap. The ability of a metal to satisfy the above requirements highly depends on its microstructure. In this study, the

relationship between microstructural parameters such as grain size and the amount of phases with bulk hardness of SnCu4Pb3 is concerned

in three areas of the product. Consequently, to achieve the desired hardness of the product in a particular area, the interaction of two

factors of the microstructure including, grain size and particles amount of the hard intermetallic compositions (Cu6Sn5) should be noted.

A thermoelastic boundary value problem of a hollow circular disc made of functionally graded materials with arbitrary gradient is analysed. The steady-state temperature distribution is assumed to be the function of the radial coordinate with prescribed temperature at the inner and outer cylindrical boundary surfaces. The material properties are assumed to be arbitrary smooth functions of the radial coordinate. A coupled system of ordinary differential equations containing the radial displacement and stress function is derived and used to get the distribution of thermal stresses and radial displacements caused by axisymmetric mechanical and thermal loads. General analytical solutions of functionally graded disc with thermal loads are not available. The results obtained by the presented numerical method are verified by an analytical solution. The considered analytical solution is valid if the material properties, except the Poisson ratio, are expressed as power functions of the radial coordinate.

The present investigation aims at fabricating a functionally graded Al-6Cr-Y2O3 composite and its microstructural and property characterization. Al-6Cr-alloys with varying percentage of Y2O3 (5-10 vol. %) have been used to fabricate FGM by powder metallurgy route. The samples were subsequently subjected to solution treatment at 610°C for 4 h followed by artificially aged at 310°C for 4 h. The microstructure, hardness and wear behavior of these FGM have been evaluated. FGM exhibited superior hardness (360 ± 5 VHN) as compared to the unprocessed composites (220 ± 5 VHN) due to the uniform dispersion of Y2O3 particles. Wear resistance of Al-6Cr-10 Y2O3 FGM were compared that of with pure Al-6Cr alloy by dry abrasive wear test. Al-6Cr-10 Y2O3 FGM composites were found to exhibit higher wear resistance with the minimum wear rate of 0.009 mm3/m compared to the Al- 6Cr alloy wear rate 0.02 mm3/m.

In this paper, a comprehensive study is carried out on the dynamic behaviour of Euler–Bernoulli and Timoshenko beams resting on Winkler type variable elastic foundation. The material properties of the beam and the stiffness of the foundation are considered to be varying along the length direction. The free vibration problem is formulated using Rayleigh-Ritz method and Hamilton’s principle is applied to generate the governing equations. The results are presented as non-dimensional natural frequencies for different material gradation models and different foundation stiffness variation models. Two distinct boundary conditions viz., clamped-clamped and simply supported-simply supported are considered in the analysis. The results are validated with existing literature and excellent agreement is observed between the results.

Thermal buckling behavior of a functionally graded material (FGM) Timoshenko beam is studied based on the transformed-section method. The material and thermal properties of the FGM beam are assumed to vary across the beam thickness according to a power-law function, a sigmoid function and an exponential function. The results of buckling temperature for the FGM beams with respective temperature-dependent and temperature-independent properties under uniform and non-linear temperature rises are presented. Some results are compared with those in the published literature to verify the accuracy of the present work. The effects of the material distributions, temperature fields, temperature-dependent properties and slenderness ratios on the thermal buckling behaviors of FGM beams are discussed. It is believed that the present model provides engineers with a simple and effective method to study the effects of various parameters of the FGM beam on its thermal buckling behavior.

On the basis of Euler-Bernoulli beam theory, the large-amplitude free vibration analysis of functionally graded beams is investigated by means of a finite element formulation. The von Karman type nonlinear strain-displacement relationship is employed where the ends of the beam are constrained to move axially. The material properties are assumed to be graded in the thickness direction according to the power-law and sigmoid distributions. The finite element method is employed to discretize the nonlinear governing equations, which are then solved by the direct numerical integration technique in order to obtain the nonlinear vibration frequencies of functionally graded beams with different boundary conditions. The influences of power-law index, vibration amplitude, beam geometrical parameters and end supports on the free vibration frequencies are studied. The present numerical results compare very well with the results available from the literature where possible.

Analytical and numerical nonlinear solutions for rotating variable-thickness functionally graded solid and annular disks with viscoelastic orthotropic material properties are presented by using the method of successive approximations. Variable material properties such as Young’s moduli, density and thickness of the disk, are first introduced to obtain the governing equation. As a second step, the method of successive approximations is proposed to get the nonlinear solution of the problem. In the third step, the method of effective moduli is deduced to reduce the problem to the corresponding one of a homogeneous but anisotropic material. The results of viscoelastic stresses and radial displacement are obtained for annular and solid disks of different profiles and graphically illustrated. The calculated results are compared and the effects due to many parameters are discussed.

In this article, the fracture behavior of functionally graded thick-walled cylinder under thermo-mechanical shock is investigated. For this purpose, classical coupled thermoelastic equations are used in calculations. First, these equations are discretized with extended finite element method (XFEM) in the space domain and then they are solved by the Newmark method in the time domain. The most general form of interaction integral is extracted for axially symmetric circumferential crack in a cylinder under thermal and mechanical loads in functionally graded materials and is used to calculate dynamic stress intensity factors (SIFs). The problem solution has been implemented in MATLAB software.

In this paper, by using a semi-analytical solution based on multi-layered approach, the authors present the solutions of temperature, displacements, and transient thermal stresses in functionally graded circular hollow cylinders subjected to transient thermal boundary conditions. The cylinder has finite length and is subjected to axisymmetric thermal loads. It is assumed that the functionally graded circular hollow cylinder is composed of N fictitious layers and the properties of each layer are assumed to be homogeneous and isotropic. Time variations of the temperature, displacements, and stresses are obtained by employing series solving method for ordinary differential equation, Laplace transform techniques and a numerical Laplace inversion.