A concept of a highly sensitive and fast-response airborne optoelectronic hygrometer, based on the absorption spectroscopy with laser light tuned to an intense ro-vibronic absorption line of H2O in the 1391– 1393 nm range is presented. The target application of this study is airborne atmospheric measurements, in particular at the top of troposphere and in stratosphere. The cavity ring-down spectroscopy was used to achieve high sensitivity. In order to avoid interference of the results by water desorbed from the instrument walls, the open-path solution was applied. Tests of the instrument, performed in a climatic chamber, have shown some advantages of this concept over typical hygrometers designed for similar applications.

Polymer-based capacitive humidity sensors emerged around 40 years ago; nevertheless, they currently constitute large part of sensors’ market within a range of medium (climatic and industrial) humidity 20−80%RH due to their linearity, stability and cost-effectiveness. However, for low humidity values (0−20%RH) that type of sensor exhibits increasingly nonlinear characteristics with decreasing of humidity values. This paper presents the results of some experimental trials of CMOS polymer-based capacitive humidity sensors, as well as of modelling the behaviour of that type of sensor. A logarithmic functional relationship between the relative humidity and the change of sensor output value at low humidity is suggested.

Humidity is probably the most important abiotic factor influencing life cycles, distribution, survival, and population dynamics of stored product pests. Although most of these pests can complete their life cycles in any given relative humidity, their prolonged development time, as well as decreased emergence rate and fecundity, have been well documented in several previous studies. In the present study, we evaluated the changes in energetic substances (lipids, soluble carbohydrates, glycogen, and proteins) accumulated in different life stages of larvae and adults of Tribolium castaneum in response to different relative humidity levels (5, 12, 22, 30, 45, and 65%). The results showed that young larvae were more susceptible to low relative humidity levels and desiccation stress. Larvae tended to accumulate higher proportions of lipids during earlier stages while their energy content shifted towards proteins with an increase in their age. Adult beetles experienced a significant decrease in their protein content immediately after they initiated reproduction. The importance of these fluctuations in the biology of the red flour beetles was discussed in detail.

Studies on the thermics, humidity and refreezing rate of two types of periglacial soils of the marine lowlands of the Hornsund area (SW Spitsbergen) were carried out during spring ablation of the snow cover (1.06.—30.06.1987). Structural soil and peat soil (moss community) were chosen. The soils were studied in places almost completely devoid of the snow cover. A considerable differentiation of temperature in vertical profile and of humidity of surface layer in both soils were found. The dynamics of ground water table and the course and depth of spring refreezing of both soils were also different. The differences reflect the different origin of soils and consequently, their different grain-size distribution, physical properties and morphology of both types of soils as well as their water balance.

Spatial differentiation of temperature and relative humidity of air on western coast of Spitsbergen in 1979—1983 is presented. Applying the author's classification of types of atmospheric circulation in the studied area, its influence on distribution of these elements is shown. Air temperature in the area is related more to the degree of climate continentality than to its latitude. The lowest mean 5—year temperatures were calculated for stations with highest degrees of thermic continentality (Svea Gruber and Svalbard Lufthavn). The highest thermic differentiation occurs from November to March (1 —4°C) and the lowest in May—June and August—October (0.0— 1.5°C). It is opposite if relative humidity is concerned: the highest differences occur in summer (10—15%) and the lowest in winter (0—9%). Influence of atmospheric circulation on air temperature is larger during a polar night than a polar day. Again, it is opposite in the case of relative humidity. In both analyzed seasons the highest thermic differentiation occurred at the circulation type Ca. However, it was the lowest during a polar night at advection of air from northern and southern sectors, and during a polar day at advection from a northern sector and at the type Cc.

The paper presents studies of mathematical modelling in transonic flow through the first stage rotor of the axial compressor of homogenous and heterogeneous condensation. The condensation phenomena implemented into a commercial software is based on the classical theory of nucleation and molecular-kinetic droplet growth model. Model is validated against experimental studies available in the literature regarding the flow through the first stage of turbine compressor, i.e. the rotor37 transonic compressor benchmark test. The impact of air humidity and air contamination on the condensation process for different flow conditions is examined. The influence of latent heat release due to condensation exerts a significant impact on the flow structure, thus the analysis of the air humidity and contamination influence on the condensation is presented. The results presented indicate the non-negligible influence of air humidity on the flow structure in the transonic flow regime, thus it is recommended to take condensation phenomenon under consideration in high-velocity airflow simulations.

Drought is one of the important phenomena resulting from variability and climate change. It has negative effects on all economic, agricultural and social sectors. The objective of this study is to rapidly detect climate dryness situations on an annual scale at the Mellah catchment (Northeast Algeria) for periods ranging from 31 years through the calculation of: the standardized precipitation index (SPI), the standardized Streamflow index (SSFI), the standardized temperature index (STI). Calculations made it possible to locate periods of drought more precisely by their intensity, duration and frequency, and detect years of breaks using the tests of Pettitt, rang, Lee and Heghinian, Hubert and Buishand. The use of the statistical tests for the rainfall series analyzed show all breaks, the majority of which are in 1996/1997 and 2001/2002. For the tem-peratures the breaks are situated in 1980/1981.

Moulding sands containing sodium silicate (water-glass) belong to the group of porous mixture with low resistance to increased humidity.

Thanks to hydrophilic properties of hardened or even overheated binder, possible is application of effective methods of hydrous

reclamation consisting in its secondary hydration. For the same reason (hydrophilia of the binder), moulds and foundry cores made of

high-silica moulding sands with sodium silicate are susceptible to the action of components of atmospheric air, including the contained

steam. This paper presents results of a research on the effect of (relative) humidity on mechanical and technological properties of

microwave-hardened moulding mixtures. Specimens of the moulding sand containing 1.5 wt% of sodium water-glass with module 2.5

were subjected, in a laboratory climatic chamber, to long-term action of steam contained in the chamber atmosphere. Concentration of

water in atmospheric air was stabilized for 28 days (672 h) according to the relative humidity parameter that was ca. 40%, 60% and 80% at

constant temperature 20 °C. In three cycles of the examinations, the specimens were taken out from the chamber every 7 days (168 h) and

their mechanical and technological parameters were determined. It was found on the grounds of laboratory measurements that moulds and

cores hardened with microwaves are susceptible to action of atmospheric air and presence of water (as steam) intensifies action of the air

components on glassy film of sodium silicate. Microwave-hardened moulding sands containing sodium silicate may be stored on a longterm

basis in strictly determined atmospheric conditions only, at reduced humidity. In spite of a negative effect of steam contained in the

air, the examined moulding mixtures maintain a part of their mechanical and technological properties, so the moulds and foundry cores

stored in specified, controlled conditions could be still used in manufacture.

Background: a humidity sensor is used to sense and measure the relative humidity of air. A new composite system has been fabricated using environmental pollutants such as carbon black and low-cost zinc oxide, and it acts as a humidity sensor. Residual life of the sensor is calculated and an expert system is modelled. For properties and nature confirmation, characterization is performed, and a sensing material is fabricated. Methodology: characterization is performed on the fabricated material. Complex impedance spectroscopy (CIS), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) are all used to confirm the surface roughness, its composite nature as well as the morphology of the composite. The residual lifetime of the fabricated humidity sensor is calculated by means of accelerated life testing. An intelligent model is designed using artificial intelligence techniques, including the artificial neural network (ANN), fuzzy inference system (FIS) and adaptive neuro-fuzzy inference system (ANFIS). Results: maximum conductivity obtained is 6.4×10⁻³ S/cm when zinc oxide is doped with 80% of carbon black. Conclusion: the solid composite obtained possesses good humidity-sensing capability in the range of 30–95%. ANFIS exhibits the maximum prediction accuracy, with an error rate of just 1.1%.

This paper describes the weather conditions on the NE coast of Sørkappland (South Spitsbergen) during August 2005, and considers them in the context of the general synoptic situation over the North Atlantic . A comparison of local climates features for the East and West coast of southern Spitsbergen shows that the general atmospheric circulation and direct solar radiation in summer are the decisive factors affecting weather on the East coast. Foehn effects were observed during the study period. In the East, these were triggered by the westerly cyclonic situation and, in the West, by the easterly. The differences in the intensity of foehn effects may be explained by a specific relief of the Sørkappland peninsula.

A large number of defects of castings made in sand moulds is caused by gases. There are several sources of gases: gases emitted from moulds, cores or protective coatings during pouring and casting solidification; water in moulding sands; moisture adsorbed from surroundings due to atmospheric conditions changes. In investigations of gas volumetric emissions of moulding sands amounts of gases emitted from moulding sand were determined - up to now - in dependence of the applied binders, sand grains, protective coatings or alloys used for moulds pouring. The results of investigating gas volumetric emissions of thin-walled sand cores poured with liquid metal are presented in the hereby paper. They correspond to the surface layer in the mould work part, which is decisive for the surface quality of the obtained castings. In addition, cores were stored under conditions of a high air humidity, where due to large differences in humidity, the moisture - from surroundings - was adsorbed into the surface layer of the sand mould. Due to that, it was possible to asses the influence of the adsorbed moisture on the gas volumetric emission from moulds and cores surface layers by means of the new method of investigating the gas emission kinetics from thin moulding sand layers heated by liquid metal. The results of investigations of kinetics of the gas emission from moulding sands with furan and alkyd resins as well as with hydrated sodium silicate (water glass) are presented. Kinetics of gases emissions from these kinds of moulding sands poured with Al-Si alloy were compared.

The risk of human exposure to finely-dispersed aerosol particles being airborne indoors is determined by the size and the number concentration of particles, the intensity of an aerosol emission source, the air filtration and ventilation efficiency, etc. The emphasis in this article is on behaviour patterns of aerosol particles when exposed to ultrasonic and electrostatic fields in different conditions of air temperature and relative humidity. Wood flour having sizes of interest (characteristic particle diameter about 10 μm) is chosen as a model aerosol. The article considers a physical and mathematical model presenting the evolution of aerosol particles in external fields, taking into account the moisture content and the temperature of a dispersive medium. The efficiency of ultrasonic and electrostatic precipitation in different relative humidity and temperature conditions in an enclosed space was studied using optical measurement methods of particle size and concentration.

LTCC-based pressure sensors are promising candidates for wet-wet applications in which the effect of the surrounding media on the sensor's characteristics is of key importance. The effect of humidity on the sensor's stability can be a problem, particularly in the case of capacitive sensors. A differential mode of operation can be a good solution, but manufacturing the appropriate sensing capacitors remains a major challenge. In the case of piezoresistive sensors the influence of humidity is less critical, but it still should be considered as an important parameter when designing sensors for low-pressure ranges. In this paper we discuss the stability of the sensors' offset characteristics, which was inspected closely using experimental and numerical analyses.