Effective and safe labour requires good cooperation of all the physiological systems. A proper synchronization of uterine and abdominal muscles is necessary for labour progression. Therefore, a new method for simultaneous monitoring of uterine activities and parturient’s pushing efforts is presented. A high sampled, rectified electrohysterographic signal is divided into a low, uterine passband (0.1-3.00Hz) and a high, muscular (40-100Hz) one. The time-dependent mean frequencies arse estimated for each passband separately. At the moments of uterine contraction the time-dependent LOW mean frequency was locally increased. During parturient’s pushing effort the HIGH mean frequency was increased in the manner typical for the skeletal muscles. It seems that the proposed method would be less sensitive to a measuring noise than the previously published RMS based estimators. Moreover, the proposed method enables to monitor fatigue of a uterus or abdominal muscles during the prolonged 2nd stage of a labour. It can be helpful to make a decision of Caesarean section.

Focus of the vibration expert community shifts more and more towards diagnosing machines subjected to varying rotational speeds and loads. Such machines require order analysis for proper fault detection and identification. In many cases phase markers (tachometers, encoders, etc) are used to help performing the resampling of the vibration signals to remove the speed fluctuations and smearing from the spectrum (order tracking). However, not all machines have the facility to install speed tracking sensors, due to design or cost reasons, and the signal itself has to then be used to extract this information. This paper is focused on the problem of speed tracking in wind turbines, which represent typical situations for speed and load variation. The basic design of a wind turbine is presented. Two main types of speed control i.e. stall and pitch control are presented,. The authors have investigated two methods of speed tracking, using information from the signal (without relying on a speed signal). One method is based on extracting a reference signal to use as a tachometer, while the other is phase-based (phase demodulation). Both methods are presented and applied to the vibration data from real wind turbines. The results are compared with each other and with the actual speed data.

Condition monitoring of machines working under non-stationary operations is one of the most challenging problems in maintenance. A wind turbine is an example of such class of machines. One of effective approaches may be to identify operating conditions and investigate their influence on used diagnostic features. Commonly used methods based on measurement of electric current, rotational speed, power and other process variables require additional equipment (sensors, acquisition cards) and software. It is proposed to use advanced signal processing techniques for instantaneous shaft speed recovery from a vibration signal. It may be used instead of extra channels or in parallel as signal verification.

In this paper a new pitch shifter using a complex instantaneous frequency rescaler and direct digital synthesizer is presented aimed at an application in a handset calling signal composer. The pitch shifter introduced here exhibits an excellent performance as a generator of different melodies, where the sound of each note in a melody, e.g., imitating a popular hit, is derived from a short recording of a voice of a chosen creature via complex dynamic representation processing.

Structures and characteristics ofwideband small-size phase shiftersmade with the use of single parallel stubs are presented in this paper. The stubs can be short-circuited or open-circuited on termination. Such devices arewell known, but are primarily used as components of filters ormatching circuits. The novelty, then, comes from the establishment of simple, but helpful formulae, which enable to describe the insertion phase shift and differential phase shift of a line with short and open stubs connected in parallel. These equations can be very useful for designing complex microwave multi-ports. The results of simulations and measurements of the devices, which were designed and made, are shown herein. It was also proved that the presented devices have several usable operating frequency sub-bands, and that the differential phase shift values in the higher sub-bands are greater than those in the lower operating frequency ranges. Thanks to this, the described phase shifters can be used in more than one frequency sub-band. It was stated that in the conditions under analysis, larger phase shifts can be achieved using open-circuited stubs rather than short-circuited stubs. However, the phase shifters with shorted parallel stubs can operate in a wider frequency band.

Passive radar does not have its own emitter. It uses so-called signals of opportunity emitted by non-cooperative illuminators. During the detection of reflected signals, a direct signal from a non-cooperative emitter is used as the reference signal. Detection of electromagnetic echoes is, in present day radars, performed by finding the maximum of the cross ambiguity function. This function is based on the multiplication of the received signal and the reference signal. Detection of echoes by means of a quadrature microwave phase discriminator QMPD was proposed in the work as an alternative solution for ambiguity function evaluation. This discriminator carries out vectorial summing of the received and the reference signals. The summing operations in QMPD are carried out with the aid of microwave elements and without the use of expensive digital signal processors. Definitions of the phase and phase difference of the so-called simple signals and noise signals were described. A proposal of a passive radar equipped with several independent quadrature microwave phase discriminators was presented. Ideas of algorithms of object detection and of the distance-to-object estimation designed for this radar have been also sketched.