In the era of the fight against global warming and in light of the search for energy with the least possible impact on the environment, interest in hydrogen has become a natural direction of development. Striving for a zero-emission Europe by 2050, the EU promotes low-emission and ultimately emission-free hydrogen for the widest possible use in the economy. Poland has developed a strategic document specifying the necessary activities for the use of hydrogen in the economy, which should at the same time maintain its competitiveness. Poland is currently the third producer of hydrogen in the European Union, which enables strategic thinking about maintaining Poland as a leading player on the hydrogen market in the long term. Currently, hydrogen in Poland is produced by (usually large) state-owned enterprises for their own needs with only a small margin of its resale. This is conventional hydrogen that is mainly obtained from natural gas. Therefore, it is difficult to talk about the hydrogen market, which must develop so that this raw material can be widely used in many branches of the modern economy. However, this requires taking a number of legislative, research and development and investment activities, as well as directing the national energy transformation to renewable energy sources, which may ultimately reduce the costs of pure hydrogen production. A number of actions have been taken, but the delay in legislative actions is slowing down the creation of the hydrogen market and is limiting the interest of private businesses in engaging in transformation activities.

The article presents current state of the structure of hard coal enrichment plants in Poland, taking the capacity, the range of grain enrichment and the type of equipment used into account. This data were presented in a tabular format for each Polish Coal Company operating on the Polish market. The article was also present simplified: flow sheet of the steam and coking coal enrichment system. Based on the presented data, the planned needs and trends were described in terms of increasing production efficiency, minimizing water consumption and safety of work. A list of research and development works which must be undertaken were also presented as well as factors determining the technological development of the processing plants.

The publication reflects the current situation concerning the possibilities of using augmented reality (AR) technology in the field of production technologies with the main intention of creating a tool to increase production efficiency. It is a set of individual steps that respond in a targeted manner to the possible need for assisted service intervention on a specific device. The publication chronologically describes the procedure required for the preparation and processing of a CAD model. For this preparatory process, the PTC software package is used which meets the requirements for each of the individual operations. The first step is the routine preparation of CAD models and assemblies. These are prepared based on real models located on the device, and their shape and dimensions correlate with the dimensions of the model on the device. The second phase is the creation and timing of the disassembly sequence. This will provide the model with complete vector data, which is then paired with the CAD models in AR. This phase is one of the most important. It determines the location of the model concerning its relative position on the device, provides information on the relocation of parts of the model after the sequence is started, and essentially serves as a template for the interactive part of the sequence. The last two phases are used to connect CAD models with vector data, determine their position for the position mark, and prepare the user interface displayed on the output device. The result of this procedure is a functional disassembly sequence, used for assisted service intervention of a worker in the spindle drive of the Emco Mill 55 device.

The article presents the possibility of increasing the production efficiency in an enterprise dealing in the production of lounge furniture. The literature review shows that Poland is the sixth country in the world in the amount of furniture production. It is also one of the leading exporters of upholstered furniture in Europe. Each year, the value of furniture sales production increases by a few percentage points. Due to the constantly growing customer orders, many companies in this industry are struggling with delays in delivering products to customers. This problem also occurs in the analyzed company. While analyzing the production process, the occurrence of a large number of non-conformities was also noticed. An analysis was carried out to indicate the number of non-conformities and the place of their occurrence. The FMEA analysis was used, which indicated which non-conformities are the most important, and the 5Why method, which allowed to indicate the cause of their occurrence. The analysis of production processes showed which activities do not bring added value and how they can be eliminated at no cost. All these measures contributed to increasing the efficiency of the production of lounge furniture.

In this article we have described a multiproduct model of economical dynamics of Gale type, in which the changes in production technology (the dynamics of Gale type production spaces) depend upon the scale of targeted investments. Under such assumptions we have proved a so-called “weak” version of a multilane turnpike theorem in the Gale type economy with varying technology which converges to a certain limit technology. It states that in the long periods of time, regardless of the initial state of the economy, the optimal growth processes almost always lie close to the family of steady growth paths with maximum growth rate called the multilane turnpike.