An elaborate study executed in the direction of exploring energy saving potential shows that more than 20% of electrical energy used in industry is used for pump systems. Experts calculate that more than 30% of this energy can be saved by improving control and diagnosis for pump systems. Unfortunately, the application ratio of such system is small and consequently a large demand for such technological advanced systems can still be observed in the pump industry. Because of this reason and still growing demand of saving energy in industry, two Universities in Germany and Switzerland together with leading German pump manufacturer decided to join their knowledge and skill to work on the project called "Smart Pump". This paper presents one of the first results of this project, which goal is the development of future control methods and diagnosis systems for intelligent pumps.

The opportunity to assess haemolysis in a designed artificial heart seems to be one of the most important stages in construction. We propose a new method for assessing haemolysis level in a rotary blood pump. This method is based on CFD calculations using large eddy simulations (LES). This paper presents an approach to haemolysis estimation and shows examples of numerical simulation. Our method does not determine the value of haemolysis but allows for comparison of haemolysis levels between different artificial heart constructions.

Centrifugal pumps are used for different applications that include pressure boosting, wastewater, water supply, heating and cooling distribution and other industrial processes. This paper presents theoretical and experimental investigations of mechanical vibrations of a centrifugal pump. The flow in this pump, which induces pressure pulsations and mechanical vibrations, have been monitored. Vibration measurements and data collection (overall vibrations levels and frequency spectrum) were extracted from the system. In addition, one of the methods used to study vibration amplitudes for this pump is forced response analysis. To study and analyze the pump system, the finite element analysis software (ANSYS) was applied. Depending on the analysis performed and investigations outcomes, the system natural frequency coincides with the vane-pass frequency (VPF) hazardously. To attenuate the system’s vibration, a vibration control element was used. The vibration levels were reduced by a factor of 2 for a tuned element as obtained from a forced harmonic response analysis of the pump system with absorber. It is shown that the inserted element allows the centrifugal pump to work in a safe operating range without any interference with its operation.

The aim of the work was modelling of shaft and calculation of natural vibration frequencies and critical rotations of a large-size, vertical mixed flow pump of total length l=4866 mm. Equations of motion were determined analytically, and then calculation results were verified by numerical modelling. The difficulty of the problem consisted in the shaft bearing, in which four hydrodynamic bearings of unknown parameters were applied. A four-mass beam supported on flexible supports of rigidity k and damping c was assumed as the discrete model of the shaft. Equations of motion for the system were derived with the method of forces. In order to verify correctness of the derived equations, one considered three models of the beam with different support configuration: the beam supported on rigid supports, the beam supported on elastic supports, and the beam supported on flexible supports of rigidity k and damping c. Calculation results are presented in tables and graphs.

The paper presents the results of hydrogeological parameters determination carried out in the area of the Muschelkalk outcrop (Middle Triassic) near Tarnów Opolski. The studies consisted of a short pumping test in 16 piezometers and then their flooding and observation of water table recovery after the stopping of the pumping. The test allowed the values of hydraulic conductivity and specific capacity of Muschelkalk layers ranging from 8.56 · 10–8 m/s to 3.63 · 10–3 m/s and from 0.0075 to 128 m3/h/1mS, respectively, to be calculated. The wide range of values is related to the fact of studying the layers characterized by high permeability and water-bearing capacity (Karchowice Beds, Diplopora Beds and Górażdże Beds) as well as layers with low permeability (Gogolin Beds). The dense network of the research points made it possible to demonstrate the surface variability of rocks permeability and water- bearing capacity, determined mostly by the direction of outcrops of individual layers. The results of the conducted studies show that the most water-bearing zone of the area is related to the carbonate rocks of the Karchowice, Diplopora and Górażdże Beds, characterized by the highest values of hydraulic conductivity k (above 2 · 10–4 m/s) and specific capacity q (above 15 m3/h/1mS), in the belt stretching latitudinally through Kosorowice–Otmice. The studied area can be considered a Polish limestone-concrete field where several mines exploiting Muschelkalk carbonate rocks operate. The results of the conducted studies may be useful for the correct prognosis of the groundwater inflow either to already existing quarries or newly designed mines within the Major Groundwater Basins.

The unique oasis of Zousfana, on the western edge of the Grand Erg Occidental, Taghit is the pearl of the oases of Saoura, a palm grove of 180 ha over an 18 km length crossed by Oued Zouzfana. It regroups the different types of landscapes of an arid zone (erg, hamada, barga – a small hill, oued ...). Taghit is known for its hydraulic civilization, the oasis in its hostile environment has survived thanks to the exploitation of rare groundwater irrigation according to the traditional customs applied to the whole of society. The peasants spur out the water resources through foggaras and traditional wells. But the intervention of modern irrigation techniques in an anarchic way has disrupted the fragile mode of irrigation and the abandonment of the palm grove. The over-exploitation of groundwater by the use of boreholes and motor pumps leads to the drying up of water sources, mists and traditional wells. Today, only 45 000 palm trees are productive and less than 1500 fruit trees. There are 500 fellahs in the entire agricultural area of Taghit, the majority of them is fleeing work in the oasis because of the lack of income from it. When comparing the results of analyses from different campaigns (2015 and 2008), a spectacular increase in the salt concentrations in the groundwater of the different palm groves is noticed. According to our investigations, the main causes of this jump are: the overexploitation of the water tables by motor pumps, the abandonment of land inside the palm grove, the lack of maintenance of the gardens, the exploitation of domestic wastewater in the irrigation. According to this preliminary study, it is important for the State to make farmers aware of the role of their traditional irrigation systems in the continuity of the oasis and life in it.

The purpose of the work was to experimentally determine the characteristics of the prototype of a Roto-Jet pump (the Pitot tube pump) during its operation under conditions typical for the domestic micro power plant. The low-boiling fluid, sold under the trade name of HFE7100 and characterised by a zero ozone depletion potential (ODP) coefficient, was used as a working medium in the organic Rankine cycle (ORC). An electric thermal oil heater with a maximum power of 2×24 kWe was used as a heat source. The pump of Roto-Jet type was specially designed for the operation with the following rated parameters of the thermodynamic cycle: nominal flow rate of the working fluid 0.17 kg/s, operating pressure 1.2 MPa. The pump was put under load using an expansion valve that simulated the operation of an expansion machine. The article discusses thermodynamic and flow conditions to be met by the pumping engine as well as results of the experimental research. Moreover, the article includes the operational characteristics of the ORC installation and the Roto-Jet pump obtained during the operation with the target working medium – HFE7100. The engineering problems the authors of this article faced when designing and testing the pumping engine prototype are also presented.

Most high-pressure fuel pumps for compression-ignition engines manufactured today are cam driven. These pumps have numerous advantages, such as low energy consumption and limited production costs. However, a problem arising from the nature of the cam mechanism is an unfavorable distribution of forces in the camshaft-plunger-cylinder system of a delivery section. The authors have proposed an innovative pump design that eliminates most of the problems present in conventional solutions. The pump utilizes a gear-based hypocycloid drive. This paper focuses mainly on the strength analysis of the two critical components (countershaft and mount) of the subassembly under the highest load – simulations were carried out for different critical load states. The following procedure of estimating fatigue life was adopted for computations: the operational evolution of stresses will be systematized to the set of amplitude stresses and mean stresses by means of the “Rainflow” method. The results obtained in the work showed that the main factor determining change of stresses was the presence of clearances in the pump mechanism. It has been proved that the values of clearances have a negative influence on the power transmission in particular – their presence results in loads being carried by the countershaft and not by the support inter-operating with it. This may cause frictional wear of teeth, leading to the improper operation of the transmission. The analysis showed that the mount was designed correctly. This facilitates the use of less demanding constructional materials.

In the paper a heating system with a vapour compressor heat pump and vertical U-tube ground heat exchanger for small residential house is considered. A mathematical model of the system: heated object - vapour compressor heat pump - ground heat exchanger is presented shortly. The system investigated is equipped, apart from the heat pump, with the additional conventional source of heat. The processes taking place in the analyzed system are of unsteady character. The model consists of three elements; the first containing the calculation model of the space to be heated, the second - the vertical U-tube ground heat exchanger with the adjoining area of the ground. The equations for the elements of vapour compressor heat pump form the third element of the general model. The period of one heating season is taken into consideration. The results of calculations for two variants of the ground heat exchanger are presented and compared. These results concern variable in time parameters at particular points of the system and energy consumption during the heating season. This paper presents the mutual influence of the ground heat exchanger subsystem, elements of vapour compressor heat pump and heated space.

This paper presents the results of thermodynamic analyses of a system using a horizontal ground heat exchanger to cool a residential building in summer and heat it in the autumn-winter period. The main heating device is a vapour compression heat pump with the ground as the lower heat source. The aim of the analyses is to examine the impact of heat supply to the ground in the summer period, when the building is cooled, on the operation of the heating system equipped with a heat pump in the next heating season, including electricity consumption. The processes occurring in cooling and heating systems have an unsteady nature. The main results of the calculations are among others the time-dependent values of heat fluxes extracted from or transferred to the ground heat exchanger, the fluxes of heat generated by the heat pump and supplied to the heated building by an additional heat source, the parameters in characteristic points of the systems, the temperature distributions in the ground and the driving electricity consumption in the period under analysis. The paper presents results of analysis of cumulative primary energy consumption of the analyzed systems and cumulative emissions of harmful substances.

Słowa kluczowe

The dynamic performance of cylindrical double-tube adsorption heat pump is numerically analysed using a non-equilibrium model, which takes into account both heat and mass transfer processes. The model includes conservation equations for: heat transfer in heating/cooling fluids, heat transfer in the metal tube, and heat and mass transfer in the adsorbent. The mathematical model is numerically solved using the method of lines. Numerical simulations are performed for the system water-zeolite 13X, chosen as the working pair. The effect of the evaporator and condenser temperatures on the adsorption and desorption kinetics is examined. The results of the numerical investigation show that both of these parameters have a significant effect on the adsorption heat pump performance. Based on computer simulation results, the values of the coefficients of performance for heating and cooling are calculated. The results show that adsorption heat pumps have relatively low efficiency compared to other heat pumps. The value of the coefficient of performance for heating is higher than for cooling

Chemical heat pumps (CHP) use reversible exothermal and endothermal chemical reactions to increase the temperature of working fluids. In comparison to the “classical” vapour compression chemical heat pumps, CHP enables us to achieve significantly higher temperatures of a heated medium which is crucial for the potential application, e.g. for production of superheated steam. Despite the advantages presented, currently, there are no installations using CHP for lowgrade waste heat recovery available on the market. The scaling up of industrial processes is still one of the greatest challenges of process engineering. The aim of the theoretical and experimental concept study presented here was to evaluate a method of reclaiming energy from low temperature waste streams and converting it into a saturated steam of temperature from 120 to 150 ◦C, which can be useful in industry. A chemical heat pump concept, based on the dilution and concentration of phosphoric acid, was used to test the method in the laboratory scale. The heat of dilution and energy needed for water evaporation from the acid solutionwere experimentally measured. The cycle of successive processes of dilution and concentration has been experimentally confirmed. A theoretical model of the chemical heat pump was tested and coefficient of performance measured.

The paper deals with an application-specific integrated circuit (ASIC) facilitating voltage conversion in thermoelectric energy harvesters. The chip is intended to be used to boost up the voltage coming from a thermoelectric module to a level that is required by electronic circuits constituting wireless sensor nodes. The designed charge pump does not need any external parts for its proper operation because all the capacitors, switches and oscillator are integrated on the common silicon die. The topography of the main functional blocks and post-layout simulations of the designed integrated circuit are shown in the article.

In this paper, the author presents the possibility of using phase trajectory for detecting damage in an axial piston pump. The wear on main part of pump elements, such as the rotor and the valve plate, was investigated, and phase trajectories were determined based on vibration signal measured in three directions on the pump's body. In order to obtain a quantitative measure of the analyzed trajectory, the At_{p,i} parameter was introduced, and the relation between this parameter and the wear on the pump's parts was determined.

This study presents a possibility of detecting wear of a valve plate in multi-piston axial pump based on time-frequency analysis of measured signals. Short-time Fourier transform STFT and the generalized Wigner-Ville algorithm WVD were used for this purpose. The tests were carried out on a multi-piston axial pump with swinging plate, in which the worn valve plates were mounted. Valve plate wear was related with the formation of flow micro-channels between the pump suction hole and its pumping hole on the plate transition zone surface. The developed channels initiate flow of the operational fluid, the results of which is lack of leak-tightness between suction and pumping zones, associated with a decrease in operational pressure and drop in general efficiency.