In Poland an increase in the of number solar thermal collectors is observed in household applications. For economic and ecological profitability the creation of a solar thermal installation design in a proper manner is essential.
In order to determine solar installations size, software calculating future solar heat gains is used. SHW software is an examples of such software. The aim of this work was to compare the simulation results with the real results of the solar installation operation. The comparison was performed by an example of a single-family house with flat plate collector installations located in south-east Poland. This installation supports domestic hot water preparation in a house occupied by four people (in two-year period of analyses). The additional heat source in this building is a gas boiler. Solar fraction parameter values were chosen for this comparison. Solar fraction is calculated as a ratio of solar heat gains used in the domestic hot water preparation process to the heat desired for domestic hot water preparation. The real results of Solar Fraction turned out to be higher than the simulation results from May to August (there were many days with Solar Fraction = 1). A difference of 20–50 percentage points was observed (Solar Fraction). Apart from this period no special differences were observed.
Additionally analyses of differences between solar heat gains calculated by Get Solar simulation software with real values (for analyzed building) was performed. This simulation analysis was done before process of building installations.
For economic growth of nation, the energy plays an important role. The excessive use of fossil fuels results the increase in global warming and depleting the resources. Due to this reason, the renewable energy sources are creating more attraction for researchers. In renewable energy sector, solar energy is the most abundant and clean source of energy. In solar thermal systems, solar air heater (SAH) is the main system which is used for heating of air. As it is simple in construction and cheaper in cost, it is of main interest for the researchers. The concept of first law and second law of thermodynamics is used for the study of the energy and exergy analysis respectively. The energy analysis is of great importance for the study of process effectiveness while the exergetic analysis is another significant concept to examine the actual behavior of process involving various energy losses and internal irreversibility. For efficient utilization of solar energy, the exergy analysis is very important tool for optimal design of solar air heaters. The aim of the present work is to review the works related to energy and exergy analysis of various types of solar air heaters and to find out the research gap for future work.
This paper presents the possibility of reducing the demand for nonrenewable primary energy for buildings using a new conceptual adsorption system of cooling and heating supplied by solar energy. Moreover, the aim of this study is to shorten the payback time of investment in the standard adsorption cooling system through its integration with the heating system. Research has been carried out for an energy-efficient medium-sized single-family building with a floor area of 140 m2 and a heat load of 4.2 kW and cold load of 4.41 kW. It has been shown that the use of an adsorption system of cooling and heating supplied by solar energy decreased the demand for nonrenewable primary energy by about 66% compared to the standard building that meets the current requirements.
The analysis of a solar installation operation was conducted on the example of a detached house in the Lesser Poland province in Poland. A gas boiler and three flat-plate collectors are located inside the house, which are used for heating water in the hot water tank with a volume of 220 dm3. The installation was established in 2012. The heat measured system (for solar gains) was added in 2014. In 2015–2019 solar heat gains measured per area of absorber were higher than 340 kWh/m2. During a two-week period in June 2015, the insolation on the horizontal plane and the temperature were measured in 4 different points of the hot water tank. On this basis, heat losses from the storage tank were determined, i.e. a decrease in temperature during periods with and without the consumption of hot water by the residents. During this period, a temperature higher than 80°C was observed several times in the hot water tank. In two parts of the hot water tank, rhe determined temperature decreases were used to obtain the heat loss amount. In the analyzed period (2 weeks), 9 days were observed with solar heat gains higher than 9 kWh/day. For these days, the value of heat loss from the solar hot water tank was estimated at over 6 kWh/day. This data corresponds to the actual heat demand for hot water preparation in the building at 7.3 kWh/day. The correlation between daily solar heat gains and solar hot water tank heat losses were also determined. In addition, based on the amount of heat losses, the value of the tank loss coefficient was estimated. The obtained value was compared with the manufacturer’s data and reference data.
Hydrogen-based power engineering has great potential for upgrading present and future structures of heat and electricity generation and for decarbonizing industrial technologies. The production of hydrogen and its optimal utilization in the economy and transport for the achievement of ecological and economic goals requires a wide discussion of many technological and operational – related issues as well as intensive scientific research. The introductory section of the paper indicates the main functions of hydrogen in the decarbonization of power energy generation and industrial processes, and discusses selected assumptions and conditions for the implementation of development scenarios outlined by the Hydrogen Council, 2017 and IEA, 2019. The first scenario assumes an 18% share of hydrogen in final energy consumption in 2050 and the elimination 6 Gt of carbon dioxide emissions per year. The second document was prepared in connection with the G20 summit in Japan. It presents the current state of hydrogen technology development and outlines the scenario of their development and significance, in particular until 2030. The second part of the paper presents a description of main hybrid Power-to-Power, Power-to-Gas and Power-to-Liquid technological structures with the electrolytic production of hydrogen from renewable sources. General technological diagrams of the use of water and carbon dioxide coelectrolysis in the production of fuels using F-T synthesis and the methanol production scheme are presented. Methods of integration of renewable energy with electrolytic hydrogen production technologies are indicated, and reliability indicators used in the selection of the principal modules of hybrid systems are discussed. A more detailed description is presented of the optimal method of obtaining a direct coupling of photovoltaic (PV) panels with electrolyzers.
The article examines the trends in the development of renewable energy in Ukraine in accordance
with the long-term strategy of the energy sector of the state in the context of the transformation
of employment in the energy sector of the country. It is emphasized that investments in renewable
energy technologies create more jobs compared to traditional electricity generation technologies.
It is defined that in Ukraine there is a significant untapped potential for energy efficiency, which
requires accelerating the pace of modernization and development of renewable energy sources and
raises the issue of labor supply to the industry. It was emphasized that there are a number of opportunities
for the development of the energy sector of Ukraine related to the development of renewable
energy sources. It is underlined that the formation of territorial-industrial clusters in Ukraine
for the production of equipment for solar and wind energy with a closed production cycle forms
long-term prerequisites for socio-economic stability in the country and stimulates employment. It is
substantiated that an important reserve for increasing employment in Ukraine is to ensure the energy
efficiency of buildings. At the same time, it was noted that in the field of renewable energy and
energy efficiency in Ukraine there is a significant shortage of qualified technicians and specialists
in the field of innovative technologies, which confirms the importance of studying the problem of
labor support in the industry. It is determined that today the solution of the issue of labor supply
of the industry takes place mainly at the level of enterprises that invest in the development of their
own staff.
The presented article examines aspects of a PV module testing using natural sunlight in outdoor conditions. The article discusses the physical sense of indexes: atmosphere purity, diffused component content, beam clear sky index. Procedures for their determination are given in relation to both instantaneous and daily values. Their close connection with the values of solar irradiance spectral distribution such as Average Photon Energy and Useful Fraction is demonstrated, as well as their usefulness in module testing in outdoor conditions. Their influence on the conversion of modules made from various absorbers and various technologies is demonstrated