The engine simulations have become an integral part of engine design and development. They are based on approximations and assumptions. The precision of the results depends on the accuracy of these hypotheses. The simplified models of frozen composition, chemical equilibrium and chemical kinetics provide the compositions of combustion products for engine cycle simulations. This paper evaluates the effects of different operating conditions and hypotheses on the exergetic analysis of a spark-ignition engine. The Brazilian automotive market has the highest number of flex-fuel vehicles. Therefore, a flex-fuel engine is considered for simulations in order to demonstrate the effects of these different hypotheses. The stroke length and bore diameter have the same value of 80 mm. The in-cylinder irreversibility is calculated for each case at the closed part of the engine cycle. A comparative analysis of these hypotheses provides a comprehensive evaluation of their effects on exergetic analysis. Higher values of accumulated irreversibility are observed for the oversimplified hypothesis.

The theoretical analysis of the charge exchange process in a spark ignition engine has been presented. This process has significant impact on the effectiveness of engine operation because it is related to the necessity of overcoming the flow resistance, followed by the necessity of doing a work, so-called the charge exchange work. The flow resistance caused by the throttling valve is especially high during the part load operation. The open Atkinson-Miller cycle has been assumed as a model of processes taking place in the engine. Using fully variable inlet valve timing the A-M cycle can be realized according to two systems: system with late inlet valve closing and system with early inlet valve closing. The systems have been analysed individually and comparatively with the open Seiliger-Sabathe cycle which is a theoretical cycle for the classical throttle governing of the engine load. Benefits resulting from application of the systems with independent inlet valve control have been assessed on the basis of the selected parameters: fuel dose, cycle work, charge exchange work and a cycle efficiency. The use of the analysed systems to governing of the SI engine load will enable to eliminate a throttling valve from the system inlet and reduce the charge exchange work, especially within the range of part load operation.

SI engines are highly susceptible to excess emissions when started at low ambient temperatures. This phenomenon has multiple air quality and climate forcing implications. Direct injection petrol engines feature a markedly different fuelling strategy, and so their emissions behaviour is somewhat different from indirect injection petrol engines. The excess emissions of direct injection engines at low ambient temperatures should also differ. Additionally, the direct injection fuel delivery process leads to the formation of PM, and DISI engines should show greater PM emissions at low ambient temperatures. This study reports on laboratory experiments quantifying excess emissions of gaseous and solid pollutants over a legislative driving cycle following cold start at a low ambient temperature for both engine types. Over the legislative cycle for testing at -7°C (the UDC), emissions of HC, CO, NOx and CO2 were higher when tested at -7°C than at 24°C. Massive increases in emissions of HC and CO were observed, together with more modest increases in NOx and CO2 emissions. Results from the entire driving cycle showed excess emissions in both phases (though they were much larger for the UDC). The DISI vehicle showed lower increases in fuel consumption than the port injected vehicles, but greater increases in emission of HC and CO. DISI particle number emissions increased by around 50%; DISI particle mass by over 600%. The observed emissions deteriorations varied somewhat by engine type and from vehicle to vehicle. Excesses were greatest following start-up, but persisted, even after several hundred seconds’ driving. The temperature of the intake air appeared to have a limited but significant effect on emissions after the engine has been running for some time. All vehicles tested here comfortably met the relevant EU limits, providing further evidence that these limits are no longer challenging and need updating.

Power generation units, suitable for individual users and small scale applications, are mainly based on spark ignition engines. In recently performed research, reductions of emissions coming from such units, especially considering carbon dioxide emissions, are deemed as the issue of particular importance. One of solutions, postponed to reduce impact of spark ignition engine-based units on the natural environment, is transition from fossil fuels into renewable gaseous fuels, as products of organic digestion. Nonetheless, development of new solutions is required to prevent further carbon dioxide emissions. The paper presents a novel dual approach developed to reduce carbon dioxide emissions from stationary power units, basing on spark ignition engine. The discussed approach includes both reduction in carbon content in the fuel, which is realized by its enrichment with hydrogen produced using the solar energy-supported electrolysis process, as well as application of post-combustion carbon dioxide separation. Results of the performed analysis suggest profitability of transition from fossil into the hydrogen-enriched fuel mixture, with significant rise in operational parameters of the system following increase in the hydrogen content. Nevertheless, utilization of the carbon dioxide separation leads to vital soar in internal energy demand, causing vital loss in operational and economical parameters of the analyzed system.