The presented article describes the method for determining one of the trace elements occurring in coalbismuth. The subjects of the analysis were coal type 34, 35 and their fly ashes derived from Jastrzębska Spółka Węglowa. The main reason for the research was the extensive use of bismuth in many industry sectors. Additionally, bismuth is on the list of deficit elements, therefore the possibility of obtaining an alternative for its recycling source of it is needed, is required. The research was carried out using atomic absorption spectrometry with electrothermal atomization in a graphite cuvette. The samples were incinerated at 800°C and microwave mineralization in a high-pressure closed system was performed until the spectrometric analysis was achieved. In order to achieve mineralization, a mixture of HF and HNO3 acids was used to turn the samples into acidic solutions. The preparation of the samples was based on available literature data and own observations. In the experiment, the effects of the additive modifier was modified by changing the temperature in further steps: drying, incineration, cooling, atomization and burning were described. In addition, the palladium modifier was used in order to limit secondary reactions and enable the evaporation of matrix components. The measurement conditions which are presented in this article allow for a linear calibration curve to be established. However, this is not clear and the definitive method for determining the bismuth in coal is carried out through the use of ET-AAS.

The aim of this work was to determine contents of cadmium, copper, lead, nickel and zinc in soils of 5 poviats in Łódzkie Voivodeship (Poviats: Łódź, Brzeziny, East Łódź, Pabianice and Zgierz). The objects of the investigation were over 500 samples of soils collected from cultivated fields, meadows, fallows and urban areas (lawns and city parks). The concentration of elements in all samples was analyzed by atomic absorption spectrometry after extraction with I rnol/drrr' HCl solution. The highest contents of heavy metals were detected in the City of Łódź area. The amounts of leachable metals in the samples under study were within the ranges: 0.3 - 48.4 ppm Cu, 1.7 - 162.9 ppm Pb; 0.9- 357.6 ppm Zn; below 2.1 ppm Cd and below 7.6 ppm Ni.

The aim of the study was to compare the serum protein profile of Bernese Mountain Dogs (BMDs) reacting positive for Bb in snap testing with the serum protein profile of dogs of other breeds (healthy and with clinical borreliosis) using the MALDI time-of-flight (MALDI-TOF) technique. The observations included five groups of dogs. BMDs reacting positively to Bb in snap serological testing and showing symptoms of borreliosis (group 1), BMDs for which no borreliosis symptoms were determined but with seropositivity for Bb determined with snap serological tests (group 2), clinically healthy BMDs with no antibodies for Bb found in the serum (group 3), five dogs of different breeds, reacting positively in serological testing, in which borreliosis symptoms were observed (group 4), clinically healthy dogs of different breeds with negative reaction in tests towards Bb (group 5). A proteomic analysis demonstrated the presence of five identical protein fractions among all five groups. An additional two protein fractions of approximately 7.630 and 15.260 kDa were found in all the serum samples obtained from the dogs positive for borrelia in a snap test, both in those exhibiting symptoms of borreliosis, and seropositive BMDs not presenting symptoms of the disease. These two additional protein fractions may be used to differentiate between seropositive and seronegative B. burgdorferi dogs and may be considered a seropositivity marker, however, it cannot be used to differentiate between animals with the clinical form of the disease and those that are only seropositive.

The electrical impedance diagnostic methods and instrumentation developed at the Gdansk and Warsaw Universities of Technology are described. On the basis of knowledge of their features, several original approaches to the broad field of electrical impedance applications are discussed. Analysis of electrical field distribution after external excitation, including electrode impedance, is of primary importance for measurement accuracy and determining the properties of the structures tested.

Firstly, the problem of electrical tissue properties is discussed. Particular cells are specified for in vitro and in vivo measurements and for impedance spectrometry. Of especial importance are the findings concerning the electrical properties of breast cancer, muscle anisotropy and the properties of heart tissue and flowing blood. The applications are both important and wide-ranging but, for the present, special attention has been focused on the evaluation of cardiosurgical interventions.

Secondly, methods of instrument construction are presented which use an electrical change in conductance, such as impedance pletysmography and cardiography, for the examination of total systemic blood flow. A new method for the study of right pulmonary artery blood flow is also introduced. The basic applications cover examination of the mechanical activity of the heart and evaluation of many haemodynamic parameters related to this. Understanding the features that occur during blood flow is of major importance for the proper interpretation of measurement data.

Thirdly, the development of electrical impedance tomography (EIT) is traced for the purposes of determining the internal structure of organs within the broad field of 2-D and 3-D analysis and including modelling of the organs being tested, the development of reconstruction algorithms and the construction of hardware.

The article presents the results of investigations performed on segregation of elements in the billets. The research were performed under standard industrial conditions, during high carbon steel production cycle. Probes (templates with the thickness of 20 mm) were taken from billets with square cross-section of 160 mm. Segregation of elements was determined based on the quantitative analysis of results performed by using spark spectrometry pursuant to PN-H-04045. Changes in concentrations of elements were analysed along two cross-sections. Element contents were performed at points distanced from each other by approx. 10 mm. The segregation of carbon, sulphur and phosphorus was determined for different billets.

Root-knot nematodes, genus Meloidogyne, are among the most plant damaging pathogens worldwide. The action of natural products against plant pathogens has been investigated to assess their effectiveness in the control of diseases. Thus, the present study aimed to evaluate the phytochemistry potential of the Ficus species for the control of Meloidogyne javanica. In vitro inhibitory activity assays were performed with crude ethanolic extracts of leaves and branches from 10 Ficus species. Among these, Ficus carica extracts exhibited strong paralysis activity against second stage juveniles (J2) (EC50 = 134.90 μg ∙ ml–1), after 72 hours. In addition, high efficacy was observed in egg-hatching inhibition at different embryonic stages. Microscopy analysis revealed severe morphological alterations in the nematode tissues at the J2 stage, as well as immotility of juveniles released from eggs in the presence of F. carica extracts. The efficacy of the treatments for the other species was very low. These differences were supported by the variation in the compound classes, mainly for alkaloids and metabolite profiles by Gas Chromatography/Mass Spectrometry (GC/MS) when F. carica was compared with the other species. The results indicated that F. carica is a promising source for the isolation and identification of molecules capable of acting in the control of M. javanica.

Grade control is crucial for ensuring that the quality of extracted ore aligns with the geological model and mining plan. This process optimises production, reduces dilution, and maximises profits. It involves geological modelling, sampling, assaying, and data analysis. However, adhering to short-term planning in mining operations can be challenging due to operational bottlenecks that arise during the grade control process and blast design, along with their associated costs. Industry standards for grade control require acquiring extensive information and knowledge to achieve a high level of certainty, which takes time. Despite that, time constraints may necessitate making decisions under risk with incomplete information. In such cases, it is important to consider the opportunities, risks, likelihood, consequences, and potential success associated with each alternative. This study presents the testing results of alternative quantitative analytical methods on samples from the Barruecopardo tungsten deposit in Spain. Spectrometric techniques, including Delayed Gamma Neutron Activation Analysis (DGNAA), Laser-induced Breakdown Spectroscopy (LIBS), and Field Portable X-ray Fluorescence (FPXRF), were employed to determine the tungsten content. Based on the findings of this investigation, a real-time decision-making tool for grade control in open-pit mining has been developed. This tool utilises representative samples directly from the blasting debris, considering the inherent risks and uncertainties associated with the process

Faecal Enterococcus hirae from domestic ducks were studied for their bioactivity to select bioactive strain for more detailed study with its probable use in poultry and also to bring novelty in basic research. After defecation, faeces (n=23, faecal mixture of 40 ducks) were sampled from domestic ducks in eastern Slovakia; birds were aged from eight to 14 weeks. E. hirae strains were identified using Matrix-assisted laser desorption/ionization time-of flight mass spectrometry with a highly probable species identification score (2.300-3.000) or a secure genus identification/ /probable species identification score (2.000-2.299), confirmed by polymerase chain reaction and phenotypization in accordance with the properties for the type strain E. hirae ATCC 9790. Strains were hemolysis negative (γ-hemolysis), and did not have active enzyme stimulating disorders. Enterocin genes were detected in three strains out of seven. Three out of four Enterocin genes were detected in Kč1/b (Ent A, P, L50A); the most frequently detected was the Ent P gene. The strains inhibited indicator strains E. faecalis, listeriae, but also Escherichia coli and Buttiauxiella strains. Lactic-acid producing E. hirae were mostly susceptible to antibiotics. Based on parameter evaluation, E. hirae Kč1/b, Kč6 can be additionally studied to select the type of bioactive substance.

In this study, heavy metals pollutions in waters, soils and vegetables were investigated from farms, near oil refinery in south of Tehran city, Iran (Shahre Ray). The most important heavy metals in Iranian oil are vanadium, cobalt, nickel, arsenic and mercury (V, Co, Ni, As, Hg). In this region, the concentration of heavy metals in soils, well waters and leafy edible vegetables were evaluated in ten different points of farms. Geographic information systems (GIS) were used to estimate the levels of heavy metals concentration at unmeasured locations. After sample preparation, concentrations of heavy metals in vegetables, soils and waters were determined by atomic absorption spectrometry (AAS). Five different leafy edible vegetables from farms, i.e., Persian leek, dill, parsley, spinach and radish were sampled in spring, summer and autumn 2012. In vegetables and well water samples, the concentrations of V, Ni and Co were above the permissible limit of heavy metals as compared to WHO guidelines and the concentrations of these metals in agricultural soils were found to be lower in accordance to soil references. The industrial waste waters had high concentration of heavy metals in this area. In consequence, the results of this study indicate that industrial waste water can cause pollution in well waters and edible vegetables. So, this region is not suitable for cultivation and growing vegetables.

Many species of Trichoderma produce secondary metabolites such as volatile organic compounds (VOCs) that reduce plant diseases and promote their growth. In this work we evaluated the antagonistic effects of VOCs released by eight strains of two Trichoderma species against Pyrenophora teres Drechsler, the causal agent of barley net blotch. Antagonism was estimated based on the percentage of mycelial growth inhibition according to the confronted cultures method. VOCs extraction and identification were performed by gas chromatography and mass spectrometry, through different methodologies for VOCs emitted by antagonists and pathogens alone or when confronted. VOCs produced by all Trichoderma strains inhibited mycelial growth of the pathogen in a range of 3 to 32%, showing weak and unpigmented mycelia with vacuolization. In addition, P. teres stimulated the release of VOCs by both Trichoderma species. The major groups of VOCs detected were sesquiterpenes, followed by diterpenes, terpenoids and eight-carbon compounds. This is the first report about characterization of volatiles emitted by Trichoderma in the presence of P. teres.

Product quality tests require accurate and precise analytical techniques. Fertilizers belong to a group

of products whose chemical composition is of great importance due to health, environmental and economic

reasons. The following paper presents the results of the research into the content of selected substances in several mineral fertilizers manufactured in Poland. Ion chromatography (IC) was employed to determine selected

inorganic anions and cations, whereas energy dispersive X-ray fluorescence spectrometry (EDXRF) was used

to determine the content of selected elements.

SDS-PAGE electrophoresis was used to study the effect of NaCl on protein expression in two cultivars of tomato (Solanum lycopersicum L.): Edkawi (salt-tolerant) and Castle rock (salt-sensitive). Five-day-old seedlings were grown on MS agar media supplemented with 0, 50, 100, 150, 200 and 300 mM NaCl. Two days after treatment the seedlings were examined to determine the effect of salt on their growth and to relate that to protein banding variations. Gel analysis showed differences in at least 4 protein bands with molecular weights at 20, 25, 45 and 65 kDa. These proteins were induced in the 50 mM NaCl treatment in the salt-sensitive cultivar, then decreasing to undetectability at higher concentrations. In the salt-tolerant cultivar, most of the proteins exhibited a more or less steady expression pattern and maintained expression through the 200 mM NaCl treatment. All proteins gave weak or no expression signals at 300 mM NaCl, the treatment that proved lethal. Differentially expressed bands were identified using MALDI-TOF mass spectrometry. The putative function of each identified protein in relation to salt stress is discussed.

The aim of the study was to estimate the content of trace elements: zinc, cadmium, lead, molybdenum and nickel in products and wastes of coal treatment from Upper-Silesian Basin. Two analytical methods were applied: atomic absorption spectrometry (FAAS, ETAAS) and anodic (ASY) and adsorptive stripping voltammetry (AdSY). ASY is used to determine zinc, cadmium and lead; AdSY molybdenum and nickel, and FAAS and ETAAS to determine all elements. In the case of Zn, Ni, Mo, Pb and Cd determined by FAAS (ETAAS) the concentrations were practically the same as those obtained by ASY or AdSY.

Anestrus is essential to an unsuccessful pregnancy in dairy cows. One of the many factors that influences anestrus is the inactive ovary. To characterize in detail the plasma metabolic pro- file, anestrus cows suffering from inactive ovaries were compared with those with natural estrus. The Holstein cows 60 to 90 day postpartum in an intensive dairy farm were assigned into inactive ovaries groups (IO, n=20) and natural estrus group (CON, n=22) according to estrus signs and rectal palpation of ovaries. Plasma samples from two groups of cows were collected from the tail vein to screen differential metabolites using gas chromatography/mass spectrometry (GC/MS) techniques and multivariate statistical analysis and pathways. The results showed that 106 compounds were screened by GC/MS and 14 compounds in the IO group were decreased by analyzing important variables in the projection values and p values of MSA.Through pathway analysis, 14 compounds, mainly associated with carbohydrate metabolism and amino acid meta- bolism, were identified to results in IO, which may seriously affect follicular growth. Metabolo- mics profiling, together with MSA and pathway analysis, showed that follicular growth and development in dairy cows is related to carbohydrate and amino acid metabolism by a single or multiple pathway(s).

In this article, we present the results of the first application of 2–benzoylpyridine (2–BP) as a carrier in adsorptive polymeric materials dedicated for the removal of Ag(I) and Cu(II) ions from model acidic solutions. In the first stage of the research, the classical solvent extraction, in which 2–BP was used as an extractant, allowed to determine the proper conditions for conducting adsorptive processes. The stability constants of 2–BP complexes with analyzed metal ions were determined using the spectrophotometric method. The electrospray ionization (ESI) high-resolution mass spectrometry (HRMS) method was applied for the confirmation of the ability of 2–BP molecules to form complexes with Cu ²⁺¸ metal ions in a solution and to determine the elemental composition of generated complexes (to identify the ratio of the number of metal ions to the number of molecules of 2–BP). The obtained results indicate that both the adsorptive processes and solvent extraction strongly depend on the properties of metal ions and that the use of 2–BP as a carrier/extractant allows for efficient removal of silver(I) ions and much less effective removal of copper(II) ions. The utilization of adsorptive polymeric materials is in line with the contemporary research trends that focus on eco-friendly and cost-effective methods.

This work reports on the investigation of homogeneity of the inside of indium micro-bumps/ columns placed on Ti/Pt/Au under bump metallisation. This is very important for connection resistivity, long-time durability, and subsequent hybridisation process (e.g., die-bonding). Gold reacts with indium to form intermetallic alloys with different chemo-physical parameters than pure indium. The geometrical and structural parameters of intermetallic alloys were analysed based on transmission electron microscope images. Distribution of elements in the investigated samples was determined using the transmission electron micro-scope with energy dispersive spectroscopy method. A thickness of intermetallic alloy was 1.02 μm and 1.67 μm in non-annealed (A) and annealed (B) indium columns, respectively. The layered and column-like interior structure of alloys was observed for both samples, respectively, with twice bigger grains in sample B. The graded chemical composition of Au-In intermetallic alloy was detected for the non-annealed In columns in contrast to the constant composition of 40% of Au and 60% of In for the annealed sample B. The atomic distribution has a minor impact on the In column mechanical stability. A yield above 99% of an In column with a 25 µm diameter and a 11 µm height is possible for a uniform columnar structure of intermetallic alloy with a thickness of 1.67 μm.

The chemical composition of commercial thyme oils, freshly hydrodistilled EO (essetntial oil) from dried thyme herb and thymol, the main thyme oil constituent, were analyzed in the aspect of possible cytotoxic effect against MCF-7 breast cancer and normal L929 mouse fibroblast cell lines. Based on the GC-MS analysis, it was found that the commercial essential oils revealed similarities in their chemical composition. The content of main components such as thymol, linalool and α-pinene was almost equal. Interestingly, the EO obtained by hydrodistillation from Thymi herba showed considerable differences in the percentage content of some main constituents. The reason for the differences may be caused by the intraspecific chemical variability of T. vulgaris L. Four types of tested EOs can be classified as a ‘thymol’ chemotype, with thymol as the predominant compound. The thymol alone and the freshly hydrodistilled EO demonstrated the highest cytotoxic effect against used cell lines. The difference in IC50 values suggests more sensitive L929 cells are more sensitive in both the CCK-8 assay (except EOs Kawon) and the NRU assay.

The methods arc described for determinations of Al, Fe, Ca, Mg, Ba, Cr, Mn, Ni, Cu, Zn, Pb, Cd, V and Sr in botanical, coal fly ash and soil samples by flame atomic absorption spectrometry (FAAS), and inductively coupled plasma atomic emission spectrometry (!CP-AES). Special attention has been paid to sample preparation, an important stage at which a sample is explored to contaminants. Results of the analysis of all samples arc discussed.