A large number of infrastructural concrete buildings are protected against aggressive environments by coating systems. The functionality of these coating systems is mainly affected by the composition and thickness of the individual polymeric layers. For the first time ever, a mobile nuclear magnetic resonance (NMR) sensor allows a non-destructive determination of these important parameters on the building site. However, before this technique can be used on steel-reinforced concrete elements, the potential effect of the reinforcement on the measurement, i.e. the NMR signal, needs to be studied. The results show a shift of the NMR profile as well as an increase of the signals amplitude in the case of the reinforced samples, while calculating the thickness of concrete coating leading to identical results.

Testing of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors working in electronic devices as protective elements, on the basis of estimating temperature increments on varistor surfaces, registered by an infrared camera during surge resistance tests with standard voltage levels. To determine acceptable temperature increments on a tested varistor, preliminary testing was performed of P22Z1 (Littelfuse) and S07K14 (EPCOS) type varistors, working first at a constant load and presently during surge tests,. The thermographic test results were compared with measured varistor capacity values before and after tests. It was found that recording with thermography temperature increments greater than 6°C for both P22Z1 and S07K14 varistor types detects total or partial loss of varistor protective properties. The test results were confirmed by assessment of protective properties of varistors working in output circuits of low nominal voltage devices.

This paper deals with the problem of nonstationarity of regressors in binary choice model. The limit distribution of the ML-estimator is mixed normal, but restriction testing shall not be based on standard t-statistic. The results of the conducted Monte Carlo experiment demonstrate that the true size of the restriction test is far from the significance level. Therefore, the t-Student statistic should be modified and this paper proposes its modification. The results of the Monte Carlo investigation point to the superiority of the new statistic.

A technology that utilizes penetrating rays is one of the oldest nondestructive testing methods. Nowadays, the process of radiogram analysis is performed by qualified human operators and automatic systems are still under development. In this work we present advanced algorithms for automatic segmentation of radiographic images of welded joints. The goal of segmentation of a radiogram is to change and simplify representation of the image into a form that is more meaningful and easier to analyse automatically. The radiogram is divided into parts containing the weld line, image quality indicators, lead characters, and possible defects. Then, each part is analysed separately by specialized algorithms within the framework of the Intelligent System for Radiogram Analysis.

In this work, the influence of both characteristics of the lens and misalignment of the incident beams on roughness measurement is presented. To investigate how the focal length and diameter affect the degree of correlation between the speckle patterns, a set of experiments with different lenses is performed. On the other hand, the roughness when the beams separated by an amount are non-coincident at the same point on the sample is measured. To conclude the study, the uncertainty of the method is calculated.

This study examined whether differences in reverberation time (RT) between typical sound field test rooms used in audiology clinics have an effect on speech recognition in multi-talker environments. Separate groups of participants listened to target speech sentences presented simultaneously with 0-to-3 competing sentences through four spatially-separated loudspeakers in two sound field test rooms having RT = 0:6 sec (Site 1: N = 16) and RT = 0:4 sec (Site 2: N = 12). Speech recognition scores (SRSs) for the Synchronized Sentence Set (S3) test and subjective estimates of perceived task difficulty were recorded. Obtained results indicate that the change in room RT from 0.4 to 0.6 sec did not significantly influence SRSs in quiet or in the presence of one competing sentence. However, this small change in RT affected SRSs when 2 and 3 competing sentences were present, resulting in mean SRSs that were about 8-10% better in the room with RT = 0:4 sec. Perceived task difficulty ratings increased as the complexity of the task increased, with average ratings similar across test sites for each level of sentence competition. These results suggest that site-specific normative data must be collected for sound field rooms if clinicians would like to use two or more directional speech maskers during routine sound field testing.

This paper presents the measurement of vibrational properties of sundatang soundboard. Sundatang is a plucked stringed traditional musical instrument that is popular among the Kadazandusun communities in Sabah, Malaysia. The vibrational properties of the soundboard are measured using CADA-X impact hammering system in a condition where the instrument is without any string. There are two types of sundatang used in this study; one made from acacia and the other from vitex wood. In this measurement, frequency response functions (FRFs) and modal parameters of the top plate and back plate of this instrument are obtained. It is found that in free edge, fundamental frequency of both plates of acacia sundatang is greater than the vitex sundatang in a range of 112 Hz to 230 Hz. However, in clamped edge (attached to its ribs), it was modified to a lower frequency and closer to each other in the range of 55 Hz to 59 Hz. Another finding is the detection of the excitation of similar mode shape at different resonance frequencies. This phenomenon is termed as Different State of Mode (DSM) which is observed may be because the number of testing points is not enough. Findings of this study provide important information to the study of quality development of this instrument

The modified air gap torque method to determine the efficiency of squirrelcage induction motor was presented. of testing which continues the authors' work on application of AGT method to estimating induction motor's efficiency are discussed. The proposed method is verified in a number of selected low-power motors.

The paper presents a heuristic approach to the problem of analog circuit diagnosis. Different optimization techniques in the field of test point selection are discussed. Two new algorithms: SALTO and COSMO have been introduced. Both searching procedures have been implemented in a form of the expert system in PROLOG language. The proposed methodologies have been exemplified on benchmark circuits. The obtained results have been compared to the others achieved by different approaches in the field and the benefits of the proposed methodology have been emphasized. The inference engine of the heuristic algorithms has been presented and the expert system knowledge-base construction discussed.

This paper deals with the evaluation of the corrosion resistance of the Al-Si alloys alloyed with the different amount of antimony.

Specifically it goes about the alloy AlSi7Mg0,3 which is antimony alloyed in the concentrations 0; 0,001; 0,005; 0,01 a 0,05 wt. % of

antimony. The introduction of the paper is dedicated to the theory of the aluminium alloys corrosion resistance, testing and evaluation of

the corrosion resistance. The influence of the antimony to the Al-Si alloys properties is described further in the introduction. The

experimental part describes the experimental samples which were prepared for the experiment and further they were exposed to the

loading in the atmospheric conditions for a period of the 3 months. The experimental samples were evaluated macroscopically and

microscopically. The results of the experiment were documented and the conclusions in terms of the antimony impact to the corrosion

resistance of the Al-Si alloy were concluded. There was compared the corrosion resistance of the Al-Si alloy antimony alloyed (with the

different antimony content) with the results of the Al-Si alloy without the alloying after the corrosion load in the atmospheric conditions in

the experiment.

Experiments of filling the model moulds cavity of various inner shapes inserted in rectangular cavity of the casting die (dimensions: 280

mm (height) x 190 mm (width) x 10 mm (depth) by applying model liquids of various density and viscosity are presented in the paper.

Influence of die venting as well as inlet system area and inlet velocity on the volumetric rate of filling of the model liquid – achieved by

means of filming the process in the system of a cold-chamber casting die was tested. Experiments compared with the results of simulation

performed by means of the calculation module Novacast (Novaflow&Solid) for the selected various casting conditions – are also

presented in the paper.

The paper is concerned with comparing the methods for determining the ferrite content in castings from duplex stainless steels. It uses Schaeffler diagram, empirical formula based calculation, image analysis of metallographic sample, X-ray diffraction and measurement with a feritscope. The influence of wall thickness of the casting on the ferrite content was tested too. The results of the experiments show that the casting thickness of 25 or 60 mm does not have a significant effect on the measured amount of ferrite. The image analysis of metallographic sample and the measurement with the feritscope appear to be the most suitable methods. On the contrary, predictive methods, such as Schaeffler diagram or empirical formula based calculation are only indicative and cannot replace the real measurements. X-ray diffraction seems to be the least suitable measuring method. Values of ferrite content measured in such a way often deviated from the values measured by image analysis and with feritscope.

The goal of this article is non-destructive ultrasonic testing of internal castings defects. Our task was to cast several samples with defects like porosity and cavities (where belongs mostly shrinkages) and then pass these samples under ultrasonic testing. The characteristics of ultrasonic control of castings are presented in the theoretical part of this article. Ultrasonic control is a volume non-destructive method that can detect internal defects in controlled materials without damaging the construction. It is one of the most widely used methods of volume non-destructive testing. For experimental control were made several cylindrical samples from ferritic grey and ductile cast iron. Because of the form and dispersion of graphite of grey cast iron it was not possible to make ultrasonic records on this casting with probe we used, so we worked only with ductile cast iron. Ultrasonic records of casting control are shown and described in the experimental part. The evaluation of the measurement results and the reliability of the ultrasonic method in castings control is listed at the end of this article.

Advanced metallic material processes (titanium) are used or developed for the production of heavily loaded flying components (in fan blade construction). The article presents one process for diagnosing the blade interior by means of laser ultrasonography. The inspection of these parts, which are mainly made of titanium, requires the determination of the percentage of bonded grain sizes from around 10 to 30 μm. This is primarily due to the advantages of a high signal-to-noise ratio and good detection sensitivity. The results of the research into the internal blade structure are attached.

The paper presents an analogue circuit testing method that engages the analysis of the time response to a non-periodic stimulus specialized for the verification of selected specifications. The decision about the current circuit diagnostic state depends on an amplitude spectrum decomposition of the time response measured during the test. A shape of the test excitation spectrum is optimized with the use of a differential evolution algorithm and it allows for achieving maximum fault coverage and the optimal conditions for fault isolation. Genotypes of the evolutionary system encode the amplitude spectrum of candidates for testing stimuli by means of rectangle frequency windows with amplitudes determined evolutionarily.

In the paper a method using active thermography and a neural algorithm for material defect characterization is presented. Experimental investigations are conducted with the stepped heating method, so-called time-resolved infrared radiometry, for the test specimen made of a material with low thermal diffusivity. The results of the experimental investigations were used in simulations of artificial neural networks. Simulations are performed for three datasets representing three stages of the heating process occurring in the investigated sample. In this work, the simulation research aimed to determine the accuracy of defect depth estimation with the use of the mentioned algorithm is descibed

Digital holography (DH) which is the technology of acquiring and processing measurement data via a CCD camera is spreading to industrial applications, finds wide employment in engineering problems of testing and investigation. In this paper, a simple digital holographic system, comprising a He-Ne laser source, CCD camera and analyzing software, is used for testing surface flatness and detecting the presence of a propagating crack on the surface plane and the effect of the crack on the neighborhood. Phase variations across the surfaces planes are extracted to represent the surface deviation from a reference plane. The analysis methods differ according to the interference fringes in the recorded holograms. Both fringe tracking and Fourier transform with phase unwrapping methods are used in the interpretation of interferometric fringe patterns.