This paper reports the results of research involving observations of flow patterns during air-oil-water three-phase flow through a vertical pipe with an internal diameter of 0.03 m and a length of 3 m. The conductometric method based on the measurement of electrical conductivity of the gas-liquid-liquid system was used to evaluate the flow patterns. In the studies, a set of eight probes spaced concentrically in two tube sections (four probes per each) with a spacing of 0.015 m were used. The paper presents a theoretical description of the test method and the analysis of the measurement results for air-oil-water multiphase flow system. Results of this study indicate that the developed method of characterizing the voltage of the gas-liquid-liquid system can be an important tool supporting other methods to identify flow patterns, including visual observation.

Novel method of space-vector-based pulsewidth modulation (PWM) has been disseminated for synchronous control of four inverters feeding six-phase drive based on asymmetrical induction motor which has two sets of windings spatially shifted by 30 electrical degrees. Basic schemes of synchronized PWM, applied for control of four separate voltage source inverters, allow both continuous phase voltages synchronization in the system and required power sharing between DC-sources. Simulations show a behavior of six-phase system with continuous and discontinuous versions of synchronized PWM.

This original paper deals with a new approach for the study of behavior in nonlinear regime of a new three-phase high voltage power supply for magnetrons, used for the microwave generators in industrial applications. The design of this system is composed of a new three-phase leakage flux transformer supplying by phase a cell, composed of a capacitor and a diode, which multiplies the voltage and stabilizes the current. Each cell. in turn, supplies a single magnetron. An equivalent model of this transformer is developed taking into account the saturation phenomenon and the stabilization process of each magnetron. Each inductance of the model is characterized by a non linear relation between flux and current. This model was tested by EMTP software near the nominal state. The theoretical results were compared to experimental measurements with a good agreement. Relative to the current device, the new systemprovides gains of size, volume, cost of implementation and maintenance which make it more economical.

Long transmission lines have to be compensated to enhance the transport of active power. But a wrong design of the compensation may lead to subsynchronous resonances (SSR). For studies often park equivalent circuits are used. The parameters of the models are often determined analytically or by a three-phase short-circuit test. Models with this parameters give good results for frequencies of 50 Hz and 100 Hz resp. 60 Hz and 120 Hz. But SSR occurs at lower frequencies what arises the question of the reliability of the used models. Therefore in this publication a novel method for the determination of Park equivalent circuit parameters is presented. Herein the parameters are determined form time functions of the currents and the electromagnetic moment of the machine calculated by transient finite-element simulations. This parameters are used for network simulations and compared with the finite-element calculations. Compared to the parameters derived by a three-phase short-circuit a significant better accuracy of simulation results can be achieved by the presented method.

Many parts of remote locations in the world are not electrified even in this Advanced Technology Era. To provide electricity in such remote places renewable hybrid energy systems are very much suitable. In this paper PV/Wind/Battery Hybrid Power System (HPS) is considered to provide an economical and sustainable power to a remote load. HPS can supply the maximum power to the load at a particular operating point which is generally called as Maximum Power Point (MPP). Fuzzy Logic based MPPT (FLMPPT) control method has been implemented for both Solar and Wind Power Systems. FLMPPT control technique is implemented to generate the optimal reference voltage for the first stage of DC-DC Boost converter in both the PV and Wind energy system. The HPS is tested with variable solar irradiation, temperature, and wind speed. The FLMPPT method is compared with P&O MPPT method. The proposed method provides a good maximum power operation of the hybrid system at all operating conditions. In order to combine both sources, the DC bus voltage is made constant by employing PI Controllers for the second stage of DC-DC Buck-Boost converter in both Solar and Wind Power Systems. Battery Bank is used to store excess power from Renewable Energy Sources (RES) and to provide continuous power to load when the RES power is less than load power. A SPWM inverter is designed to convert DC power into AC to supply three phase load. An LC filter is also used at the output of inverter to get sinusoidal current from the PWM inverter. The entire system was modeled and simulated in Matlab/Simulink Environment. The results presented show the validation of the HPS design.

Structures and characteristics ofwideband small-size phase shiftersmade with the use of single parallel stubs are presented in this paper. The stubs can be short-circuited or open-circuited on termination. Such devices arewell known, but are primarily used as components of filters ormatching circuits. The novelty, then, comes from the establishment of simple, but helpful formulae, which enable to describe the insertion phase shift and differential phase shift of a line with short and open stubs connected in parallel. These equations can be very useful for designing complex microwave multi-ports. The results of simulations and measurements of the devices, which were designed and made, are shown herein. It was also proved that the presented devices have several usable operating frequency sub-bands, and that the differential phase shift values in the higher sub-bands are greater than those in the lower operating frequency ranges. Thanks to this, the described phase shifters can be used in more than one frequency sub-band. It was stated that in the conditions under analysis, larger phase shifts can be achieved using open-circuited stubs rather than short-circuited stubs. However, the phase shifters with shorted parallel stubs can operate in a wider frequency band.

The exact measurement of multiphase flow is an important and essential task in the oil and petrochemical related industries. Several methods have already been proposed in this field. In the existing methods, flow rate measurement depends on the fluid flow pattern. Flow pattern recognition requiring calibration has created instability in such systems. In this paper, a imple and reliable method is proposed which is based on ultrasonic tomography. It is free from calibration and instability problems that existing methods have. The obtained data from a 32-digit array of ultrasonic sensors have been used and the two-phase flow rate including liquid and gas phases have been calculated through a simple algebraic algorithm. Simulation results show that while applying this method the measurement technique is independent from the fluid flow pattern and the system error is decreased. For the proposed algorithm, the average amount of the spatial imaging error (SIE) for a bubble at different positions inside the pipe is about 5%.

To obtain anti-corrosive thermo-diffusion zinc coatings, the authors use highly effective zinc saturating mixtures. This technology makes it possible to obtain coatings with a high zinc content in the δ-phase as well as a zinc-rich phase of FeZn13 (ζ-phase) on the coating surface. As a result of long-term studies into the corrosion properties of thermo-diffusion zinc (TDZ) coatings conducted by the authors, a number of features of their corrosive behavior have been established. The corrosion rate of those coatings in desalted and chloride-containing media is lower than those of galvanic or hot-dip zinc coatings. The corrosion behavior depends on the content of zinc on the surface and the texture features of the coating. The results showed that on the surface of thermo-diffusion coatings in the corrosion on media containing chloride ions, zinc hydroxychloride (simonkolleite – Zn5Cl2[OH]8[H2O]) has been formed. Compared to coatings obtained by other methods, the rate of simonkolleite formation was higher on TDZ coatings, which might have a positive effect on their resistance in aggressive atmospheres.