Applied sciences

Archives of Foundry Engineering

Content

Archives of Foundry Engineering | 2024 | vol. 24 | No 1

Download PDF Download RIS Download Bibtex

Abstract

The paper presents the experimental results on the determination of melt parameters such as the energy of the boundary, contact angle, density and kinematic viscosity of low and medium alloy steels at different temperatures, as well as the dispersion of their dendritic structure in solidified castings. The analysis of the data obtained allowed revealing using mathematical models the influence of the chemical composition and temperature of melts on their properties and the dendritic structure of castings. It was established the variation of the melt parameters depending on the particular chemical elements of steels as C, Si, Mn, O, P, V, Cr. The established analytical dependences shown that increasing density and viscosity contributes to the dispersion of the dendritic structure and viscosity is of the major effect. The derived quantitative patterns allows to evaluate structure formation of cast structural low and medium alloy steels.
Go to article

Bibliography

[1] Volmer, M. (1939). Kinetik der Phasenbildung. Dresden, Leipzig, Steinkopf.
[2] Frank, F. (1949). Model grow crystallization. Discusion of the Faraday Society. 5, 48-54.
[3] Frenkel, Ya.I. (1975). Kinetic theory of liquid. M.: Publishing House of the Academy of Sciences of the USSR.
[4] Wilson, D.P. (1965) Structure of liquid metals and alloys. Metallurgical Reviews, 10(1), 381-590.
[5] Cao, Y.F., Chen, Y., Ma, X.P., Fu, P.X., Kang, X.H., Liu, H.W., Li, D.Z. (2016). The effect of alloy elements on the density variation of steel melt at the interdendritic region during solidification. In 4th International Conference on Advances in Solidification Processes (ICASP-4). IOP Conf. Series: Materials Science and Engineering, 8-11 July 2014 (pp. 1-7).
[6] Arsentiev, P.P., Koledov, L.A. (1976). Metallicheskie rasplavy i ih svojstva [Metal melts and their properties]. Moskva: Metallurgiya [In Russian].
[7] Ershov, G.S., Bychkov, Yu.B. (1982). Fiziko-himicheskie osnovy racionalnogo legirovaniya stalej i splavov [Physical and chemical bases of rational alloying of steels and alloys]. Moskva: Metallurgiya [In Russian].
[8] Ryzhonkov, D.I., Arsentiev, V.V., Yakovlev, V.V. (1989). Teoriya metallurgicheskih processov [Theory of metallurgical processes]. Moskva: Metallurgiya [In Russian].
[9] Kupriyanov, A.A. & Filippov, S.I. (1968). Density and structural changes of iron and alloys of iron with carbon. Izv.vuz. Ferrous metallurgy. 9, 10-15.
[10] Ershov, G.S., Bychkov, Yu.B. (1983). Svojstva metallurgicheskih rasplavov i ih vzaimodejstvie v staleplavilnyh processah [Properties of metallurgical melts and their interaction in steelmaking processes]. Moskva: Metallurgiya [In Russian].
[11] Goldstein, Ya.E., Mizin, V.G. (1986). Modificirovanie i mikrolegirovanie chuguna i stali [Modification and microalloying of cast iron and steel]. Moskva: Metallurgiya [In Russian].
[12] Grigoryan, V.A., Belyanchikov, L. N., Stomakhin, A.Ya. (1987). Teoreticheskie osnovy elektrostaleplavilnyh processov [Theoretical fundamentals of electric steelmaking processes]. Moskva: Metallurgiya [In Russian].
[13] Baum B.A. (1979). Metallicheskie zhidkosti - problemy i gipotezy [Metallic liquids - problems and hypotheses]. Moskva: Nauka [In Russian].
[14] Feng, G., Jiao, K., Zhang, J. & Gao, S. (2021). High-temperature viscosity of iron‑carbon melts based on liquid structure: The effect of carbon content and temperature. Journal of Molecular Liquids. 330, 115603, 1-10. https://doi.org/10.1016/j.molliq.2021.115603.
[15] Turnbull, D. & Fisher, J.C. (1949). Rate of Nucleation in Condensed Systems. Journal of Chemical Physics. 17, 71.
[16] Popel, S.I. (1971). Teoriya metallurgicheskih processov [Theory of metallurgical processes]. Moskva: VINITI [In Russian].
[17] Efimov, V.A., Eldarkhanov A.S. (2004). Tehnologii sovremennoj metallurgii [Technologies of modern metallurgy]. Moskva: Novye tehnologii [In Russian].
[18] Volmer, M.I., Mаnder, M. (1931). Journal of Chemical Physics. A154, 97.
[19] Flemings, M. (1974). Solidification processing. New York: Mc Graw – Hill book company.
[20] Hilling, W.B., Turnbull, D. (1956) Theory of Crystal Growth in Undercooled Pure Liquids. Journal of Chemical Physics. 24(4), 914.
[21] Turnbull, D. (1949). Thermodynamics in Metallurgy, ASM, Metals Park, Ohio.
[22] Baum, B.A. (1988). About of the relationship of liquid and solid metallic states. Rasplavy. 2(2), 18-32.
[23] Arsentiev, P.P., Yakovlev, V.V., Krashennikov, M.G. (1988). Fiziko-himicheskie metody issledovaniya metallurgicheskih processov [Physico-chemical methods for studying metallurgical processes]. Moskva: Metallurgiya [In Russian].
[24] Shvedkov, E.L. (1975). Elementarnaya matematicheskaya statistika v eksperimentalnyh zadachah materialovedeniya [Elementary mathematical statistics in experimental problems of materials science]. Kiev: Naukova dumka [In Russian].
[25] ImageJ. Image Processing and Analysis in Java. Retrieved September 11, 2023 from: https://imagej.nih.gov/ij/.
[26] Vitol, E.N. & Orlova K.B. (1984). About the energy of the boundary of liquid metals. Izv. USSR Academy of Sciences Metals. 4, 37-42.
[27] Svidunovich, N.A., Glybin, V.P., Svirko, L.K. (1989). Vzaimodejstvie komponentov v splavah [Interaction of components in alloys]. Moskva: Metallurgiya [In Russian].
[28] Chalmers, B. (1968). Teoriya zatverdevaniya [Theory of Solidification]. Moskva: Metallurgiya [In Russian].  


Go to article

Authors and Affiliations

Y. Aftandiliants
1
ORCID: ORCID
S. Gnyloskurenko
1 2
ORCID: ORCID
H. Meniailo
3
ORCID: ORCID
V. Khrychikov
3
ORCID: ORCID

  1. National University of Life and Environmental Sciences of Ukraine, Ukraine
  2. Physical and Technological Institute of Metals and Alloys, National Academy of Sciences of Ukraine, Ukraine
  3. Ukrainian State University of Science and Technologies, Ukraine
Download PDF Download RIS Download Bibtex

Abstract

The article aims to characterize Hadfield steel by analyzing its chemical composition, mechanical properties, and microstructure. The study focused on the twinning-induced work hardening of the alloy, which led to an increase in its hardness. The experimental data show that the material hardness at the surface improved considerably after solution heat treatment and work hardening, reaching more than 750 HV. By contrast, the hardness of the material core in the supersaturated condition was about 225 HV. The chemical and phase compositions of the material at the surface were compared with those of the core. The microstructural analysis of the steel revealed characteristic decarburization of the surface layer after solution heat treatment. The article also describes the effects of heat treatment on the properties and microstructure of Hadfield steel. The volumetric (qualitative) analysis of the computed tomography (CT) data of Hadfield steel subjected to heavy dynamic loading helped detect internal flaws, assess the material quality, and potentially prevent the structural failure or damage of the element tested.
Go to article

Bibliography

[1] Kalandyk, B., Tęcza, G., Zapała, R., Sobula, S. (2015). Cast high-manganese steel – the effect of microstructure on abrasive wear behaviour in miller test. Archives of Foundry Engineering. 15(2), 35-38. DOI: 10.1515/afe-2015-0033.
[2] Bartlett, L.N. & Avila, B.R. (2016). Grain refinement in lightweight advanced high-strength steel castings. International Journal of Metalcasting. 10, 401-420, DOI: 10.1007/s40962-016-0048-0.
[3] Guzman Fernandes, P.E. & Arruda, Santos, L. (2020). Effect of titanium and nitrogen inoculation on the microstructure, mechanical properties and abrasive wear resistance of Hadfield Steels. REM - International Engineering Journal. 73(5), 77-83. https://doi.org/10.1590/ 0370-44672019730023
[4] Chen, C., Lv, B., Feng, X., Zhang, F. & Beladi, H. (2018). Strain hardening and nanocrystallization behaviors in Hadfield steel subjected to surface severe plastic deformation. Materials Science and Engineering: A. 729, 178-184. DOI:10.1016/j.msea.2018.05.059.
[5] Chen, C., Zhang, F.C., Wang, F., Liu, H. & Yu, B.D. (2017). Efect of N+Cr alloying on the microstructures and tensile properties of Hadfield steel. Materials Science & Engineering. 679, 95-103. DOI:10.1016/j.msea.2016.09.106.
[6] Bolanowski, K. (2008). Wear of working elements made of Hadfield cast steel under industrial conditions. Problemy Eksploatacji. 2, 25-32.
[7] Tęcza, G., Sobula, S. (2014). Effect of heat treatment on change microstructure of cast high-manganese Hadfield steel with elevated chromium content. Archives of Foundry Engineering. 14(3), 67-70.
[8] Gürol, U., Karadeniz, E., Çoban, O., & Kurnaz, S.C. (2021). Casting properties of ASTM A128 Gr. E1 steel modified with Mn-alloying and titanium ladle treatment. China Foundry. 18, 199-206. https://doi.org/10.1007/s41230-021-1002-1
[9] Pribulová, A., Babic, J. & Baricová, D. (2011). Influence of Hadfield´s steel chemical composition on its mechanical properties. Chem. Listy. 105, 430-432.
[10] Przybyłowicz, K. (2008). Iron alloys engineering. Kielce: Wyd. Politechniki Świętokrzyskiej w Kielcach (in Polish).
[11] Stradomski, Z. (2001). On the explosive hardening of cast Hadfield steel. Proceedings of a Conference on Advanced Steel Casting Technologies. Kraków. 112-122. (in Polish).
[12] Cullity, B.D. (1964). Basics of X-ray diffraction. Warszawa: PWN. (in Polish).
[13] Bolanowski, K. (2013). The influence of the hardness of the surface layer on the abrasion resistance of Hadfield cast steel. Problemy Eksploatacji. 1, 127-139. (in Polish).
[14] Przybyłowicz, K. (2012). Metal Science. Warszawa: WNT. (in Polish).
[15] El Fawjhry, M.K. (2018). Feasibility of new ladle-treated Hadfield steel for mining purposes. International Journal of Minerals, Metallurgy and Materials. 25(3), 300, https://doi.org/10.1007/s12613-018-1573-z.
[16] Subramanyan, D.K, Swansieger, A.E. and Avery, H.S. (1990). Austenitic manganese steels. In ASM Metals Handbook. Vol. 1, 10th Ed. (p. 822-840). India: American Society of Metals, India.
[17] Zykova, A., Popova, N., Kalashnikov, M. & Kurzina, I. (2017). Fine structure and phase composition of Fe–14Mn–1.2C steel: influence of a modified mixture based on refractory metals. International Journal of Minerals, Metallurgy and Materials. 24(5), 523-529. DOI: 10.1007/s12613-017-1433-2.
[18] Vdovin, K.N., Feoktistov, N.A., Gorlenko, D.A. et al. (2019). Modification of High-Manganese Steel Castings with Titanium Carbonitride. Steel in Translation. 3, 147-151. https://doi.org/10.3103/S0967091219030136.
[19] Issagulov, A.Z., Akhmetov, A.B., Naboko, Ye.P., Kusainova, G.D. & Kuszhanova, A.A. (2016). The research of modification process of steel Hadfield integrated alloy ferroalumisilicocalcium (Fe-Al-Si-Сa/FASC). Metalurgija. 55(3), 333-336.
[20] Haakonsen, F., Solberg, J.K., Klevan, O. & Van der Eijk, C. (2011). Grain refinement of austenitic manganese steels. In AISTech - Iron and Steel Technology Conference Proceedings, 5-6 May 2011 (pp. 763-771). Indianapolis, USA.
[21] El Fawkhry, M.K. (2021). Modified hadfield steel for castings of high and low gouging applications. International Journal of Metalcasting. 15(2), 613-624. https://doi.org/10.1007/s40962-020-00492-5.
[22] EI Fawkhry, M.K., Fathy, A.M. and Eissa, M.M. (2015). New energy saving technology for producing Hadfield steel to high gouging applications. Steel Research International. 86(3), 223-230. https://doi.org/10.1002/srin.201300388.
[23] El-Fawkhry, M.K., Fathy, A.M., Eissa, M. & El-Faramway, H. (2014). Eliminating heat treatment of Hadfield steel in stress abrasion wear applications. International Journal of Metalcasting. 8, 29-36. DOI: 10.1007/BF03355569
[24] Sobula, S., Kraiński, S. (2021). Effect of SiZr modification on the microstructure and properties of high manganese cast steel. Archives of Foundry Engineering. 4, 82-86. ISSN (1897-3310).
[25] Zambrano, O.A., Tressia, G., Souza, R.M. (2020). Failure analysis of a crossing rail made of Hadfield steel after severe plastic deformation induced by wheel-rail interaction. Engineering Failure Analysis. 115, 104621. DOI: doi.org/10.1016/j.engfailanal.2020.104621.
[26] Wróbel, T., Bartocha, D., Jezierski, J., Kalandyk, B., Sobula, S., Tęcza, G., Kostrzewa, K., Feliks E. High-manganese alloy cast steel in applications for cast elements of railway infrastructure. In Współpraca 2023 : XXIX international scientific conference of Polish, Czech and Slovak foundrymen, 26-28 April 2023. Niepołomice.
[27] Młyński, M., Sobula, S., Furgał, G. (2001). Economic aspects of the oxygen-recovery melts of Hadfield cast steel in the Foundry of Metalodlew S.A. Przegląd Odlewnictwa. 51(11), 382-384. (in Polish).
[28] Wróbel, T., Bartocha, D., Jezierski, J., Sobula, S., Kostrzewa K., Feliks E. (2023). High-manganese alloy cast steel used for cast elements of railway infrastructure. Stal, Metale & Nowe Technologie. 1-2, 30-34. (in Polish).
Go to article

Authors and Affiliations

Damian Bańkowski
1
ORCID: ORCID
Piotr S. Młynarczyk
1
ORCID: ORCID
Wojciech P. Depczyński
1
ORCID: ORCID
Kazimierz Bolanowski
1
ORCID: ORCID

  1. Kielce University of Technology, Poland
Download PDF Download RIS Download Bibtex

Abstract

The work presents the effect of the addition of graphite from recycled graphite electrodes on the mechanical properties of metal matrix composites (MMC) based on the AlMg10 alloy. A composite based on the AlMg10 alloy reinforced with natural graphite particles was also tested. Further, tests of the mechanical properties of the AlMg10 alloy were performed for comparative purposes. Composites with a particle content of 5, 10 and 15 percent by volume were produced by adding introduction of particles into the liquid matrix while mechanically mixing molten alloy. The composite suspensions were gravitationally cast into metal molds. Samples for the Rm, R0.2, A and E tests were made from the prepared castings. Photos of the microstructures of the materials were also taken. The research shows that the addition of graphite to the matrix alloy causes minor changes in tensile strength (Rm) and yield strength (R02), regardless of the type of graphite used. The results of the relative elongation tests showed that the introduction of graphite particles into the matrix alloy had an adverse effect on the elongation values in the case of each of the tested composites. The introduction of graphite particles into the AlMg10 alloy significantly increased the Young’s modulus value, both in the case of composites with flake graphite (natural) and graphite from ground graphite electrodes.
Go to article

Bibliography

[1] Journal of Laws (2023). item 1587, as amended.
[2] Świądkowska, W. (2017). Jagiellonian University Repository Recycling. Cracow: Jagiellonian University Publishers.
[3] Fleszar, J. (2014). Legal, economic and organisational aspects of vehicle recycling. Buses: technology, operation, transportation systems. 15(6), 113-117.
[4] Carbograf. Graphite electrodes for furnaces arched. Retrieved June 28, 2023 from https://www.carbograf.pl/graf-elektrody-do-piecow-lukowych
[5] Łędzki, A., Michaliszyn, A., Klimczyk A. (2012). Steel melting in electric arc furnaces. Extraction metallurgy of iron, Cracow, AGH.
[6] Custom Market Insight. Global Graphite Electrode Market 2023-2032. Retrieved June 28, 2023 from https://www.custommarketinsights.com/report/graphite-electrode-market/
[7] Industry Arc. (2023) Graphite Electrodes Market Overview. Retrieved June 28, 2023 from https://www.industryarc.com/Research/Graphite-Electrodes-Market-Research-503019
[8] Festinger, N., Morawska, K., Ciesielski, W. (2019). Electrochemical properties of electrodes made of highly oriented pyrolytic graphite. In Quadrant for chemistry: a monograph: Spring Convention of the Student Section of the Polish Chemical Society, 10-14.04.2019 (pp. 45-52). Ustron.
[9] Janicka, E. (2014). Comprehensive impedance characterization of fuel cell performance. Doctoral dissertation. Gdansk University of Technology.
[10] Kuśmierek, K., Świątkowski, A., Skrzypczyńska, K. (2015). The role of the specific surface area of carbon materials used in modified graphite paste electrodes. Applied electrochemistry. Cracow: Scientific Publishing House AKAPIT.
[11] Chemistry and Business. (2023). Synthetic graphite is becoming more and more popular. Retrieved June 27, 2023 from https://www.chemiaibiznes.com.pl/artykuly/grafit-syntetyczny-coraz-chetniej-stosowany
[12] Green Energy . Refractories and Isolation. (2020). Overview of Metallurgical Graphite Electrodes and Analysis of Carbon Products Industry. Retrieved June 28, 2023 from http://pl.greenergyrefrataatarios.com/info/overview-of-metallurgical-graphite-electrodes-49845995.html
[13] BAT Reference Document for Best Available Techniques in the Production of Non-Ferrous Metals (2001). Lukasiewicz Research Network - Institute of Non-Ferrous Metals Legnica Branch, interpreter: Płonka A., Bzowski W., Przebindowski Z.
[14] Myalski, J. & Sleziona, J. (2005). Metal composites reinforced with glassy carbon particles. Foundry Review. 1(55), 24-27.
[15] Naplocha, K., Samsonowicz Z. & Janus, A. (2005). Aluminum alloy matrix composites reinforced with Al2O3 fibers and graphite. Composites. 5(2), 95-98.
[16] Łągiewka, M. & Komlasiak, C. (2021). Solidification of the Al alloy composite reinforced with graphite. Metalurgija. 60(3-4), 399-402.
[17] Tjong, S.C., Wang, H.Z. & Wu, S.Q. (1996). Wear behavior of aluminum-based matrix composites reinforced with a preform of aluminosiliate. Metallurgical and Materials Transactions. 27(8), 2385-2389. https://doi.org/10.1007/BF02651894.
[18] Łągiewka, M. & Konopka, Z. (2014). Effect of graphite addition on abrasive wear of AlMg10 alloy matrix composites reinforced with SiC particles. Archives of Foundry Engineering. 14(3), 51-54. ISSN (1897-3310).
[19] Naplocha, K. & Janus, A. (2006). Abrasion resistance of aluminum alloy matrix composites reinforced with Al2O3 fibers and graphite. Composites. 6(1), 3-8.
[20] Komlasiak, C. & Łągiewka, M. (2023). Foundry properties of composites on AlMg10 alloy matrix with SiC and Cgr particles. Metalurgija. 62(1), 149-151.
Go to article

Authors and Affiliations

Małgorzata Łągiewka
1
ORCID: ORCID

  1. Czestochowa University of Technology, Poland
Download PDF Download RIS Download Bibtex

Abstract

Manufacturing by casting method in aluminum and its alloys is preferred by different industries today. It may be necessary to improve the mechanical properties of the materials according to different industries and different strength requirements. The mechanical properties of metal alloys are directly related to the microstructure grain sizes. Therefore, many grain reduction methods are used during production or heat treatment. In this study, A356 alloys were molded into molds at 750 °C and exposed to vibration frequency at 0, 8.33, 16.66, 25, and 33.33 Hz during solidification. Optical microscopes images were analyzed in image analysis programs to measure the grain sizes of the samples that solidified after solidification. In addition, microhardness tests of samples were carried out to examine the effect of vibration and grain reduction on mechanical behavior. In the analyzes made, it was determined that the grain sizes decreased from 54.984 to 26.958 μm and the hardness values increased from 60.48 to 126.94 HV with increasing vibration frequency.
Go to article

Bibliography

[1] Mondolfo, L.F. (1979). Aluminium Alloys Structures and Properties. London: Butterworths, 806.
[2] Kocatepe, K. & Burdett, C.F. (2000) Effect of low frequency vibration on macro and micro structures of LM6 alloys. Journal of Materials Science, 35(13), 3327-3335. https://doi.org/10.1023/A:1004891809731.
[3] Schaffer, P.L. & Dahle, A.K. (2005). Settling behaviour of different grain refiners in aluminium. Materials Science and Engineering. A, 413, 373-378. https://doi.org/10.1016/j.msea.2005.08.202.
[4] Kumar, P.S., Abhilash, E., Joseph, M.A. (2010). Solidification under mechanical vibration: variation in metallurgical structure of gravity die cast A356 aluminium alloy. In International Conference on Frontiers in Mechanical Engineering (FIME), 20-22 May 2010 (pp. 140-146). India.
[5] Taghavi, F., Saghafian, H. & Kharrazi, Y.H. (2009). Study on the effect of prolonged mechanical vibration on the grain refinement and density of A356 aluminum alloy. Materials & Design. 30(5), 1604-1611. https://doi.org/10.1016/j.matdes.2008.07.032.
[6] Hernandez, F.R. & Sokolowski, J.H. (2006). Comparison among chemical and electromagnetic stirring and vibration melt treatments for Al–Si hypereutectic alloys. Journal of Alloys and Compounds. 426(1-2), 205-212. https://doi.org/10.1016/j.jallcom.2006.09.039.
[7] Jian, X., Meek, T.T. & Han, Q. (2006). Refinement of eutectic silicon phase of aluminum A356 alloy using high-intensity ultrasonic vibration. Scripta Materialia. 54(5), 893-896. https://doi.org/10.1016/j.scriptamat.2005.11.004.
[8] Chirita, G., Stefanescu, I., Soares, D. & Silva, F.S. (2009). Influence of vibration on the solidification behaviour and tensile properties of an Al–18 wt% Si alloy. Materials & Design. 30(5), 1575-1580. https://doi.org/10.1016/ j.matdes.2008.07.045.
[9] Promakhov, V.V., Khmeleva, M.G., Zhukov, I.A., Platov, V.V., Khrustalyov, A.P., & Vorozhtsov, A.B. (2019). Influence of vibration treatment and modification of A356 aluminum alloy on its structure and mechanical properties. Metals. 9(1), 87. https://doi.org/10.3390/met9010087.
[10] Selivorstov, V., Dotsenko, Y. & Borodianskiy, K. (2017). Influence of low-frequency vibration and modification on solidification and mechanical properties of Al-Si casting alloy. Materials. 10(5), 560. https://doi.org/10.3390/ma10050560.
[11] Yüksel, Ç. (2018). Titreşimli katilaştirmanin birincil ve ikincil Al7Si0, 3mg alüminyum alaşimlarinin içyapisina etkisi. Niğde Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi. 7(2), 986-992.
[12] Sulaiman, S. & Zulkifli, Z.A. (2018). Effect of mould vibration on the mechanical properties of aluminium alloy castings. Advances in Materials and Processing Technologies. 4(2), 335-343. https://doi.org/10.1080/ 2374068X.2017.1421737.
[13] Y. Seetharama Rao, Rajana Vara Prasad, Sri Ram Murthy Paladugu (2019). Experimental investigations of microstructure and mechanical properties of aluminium alloy using vibration mold. Journal of Recent Activities in Production e-ISSN: 2581-9779. 4(2), 25-34.
[14] ASM International Handbook Committee. (1990). ASM Handbook, Volume 02 - Properties and Selection: Nonferrous Alloys and Special-Purpose Materials. ASM International.
[15] Kocatepe, K. (2007). Effect of low frequency vibration on porosity of LM25 and LM6 alloys. Materials & Design. 28(6), 1767-1775. https://doi.org/10.1016/ j.matdes.2006.05.004.
[16] Naik, S.N., & Walley, S.M. (2020). The Hall–Petch and inverse Hall–Petch relations and the hardness of nanocrystalline metals. Journal of Materials Science. 55(7), 2661-2681. https://doi.org/10.1007/s10853-019-04160-w.
Go to article

Authors and Affiliations

Taha Süreyya Özgü
1
ORCID: ORCID
Recep Çalın
1
ORCID: ORCID
Naci Arda Tanış
1
ORCID: ORCID

  1. Kırıkkale University, Turkey
Download PDF Download RIS Download Bibtex

Abstract

As a part of this work, an analysis of the current state of knowledge regarding the use of additive technology - binder jetting in the production of castings was made. The binder jetting (so-called 3D printing) has become the leading method of sand mold and core production. Within this paper types of molding and core sands with organic and inorganic binders that are and can be used in technology were analyzed. The need to carry out works aimed at developing pro-ecological molding / core sands with inorganic binders and organic binders with reduced harmfulness to the environment dedicated to binder jetting technology was noticed. The influence of technology parameters on the properties of molding / core sands and the properties of cast components was analyzed. It was shown that thanks to the unlimited shapes of the systems obtained with the use of additive technologies, it is possible to influence the rate of heat dissipation through the mold, which positively effects the process of solidification and crystallization of the castings.
Go to article

Bibliography

[1] Jandyal, A., Chaturvedi, I., Wazir, I., Raina, A. & Ul Haq, M.I. (2022). 3D printing – A review of processes, materials and applications in industry 4.0. Sustainable Operations and Computers. 3, 33-42. DOI: 0.1016/j.susoc.2021.09.004.
[2] Shi, Y., Znang, J., Wen, S., Song, B., Yan, C., Wei, Q., Wu, J., Yin, Y., Zhou, J., Chen, R., Wei, Z., Jia, H., Yang, H & Nan, H. (2021). Additive manufacturing and foundry innovation. China Foundry. 18(4), 286-295. DOI: 10.1007/s41230-021-1008-8.
[3] Gawronová, M., Lichý, P., Kroupová, I., Obzina, T., Beňo, Nguyenová, I., Merta, V., Jezierski, J. & Radkovský, F. (2022). Evaluation of additive manufacturing of sand cores in terms of the resulting surface roughness. Heliyon. 8(10), 1-10. DOI: 10.1016/j.heliyon.2022.e10751.
[4] Shangguan, H., Kang, J., Deng, C., Hu, Y. & Huang, T. (2017). 3D-printed shell-truss sand mold for aluminum castings. Journal of Material Processing Technology. 250, 247-253. DOI: 10.1016/j.jmatprotec.2017.05.010.
[5] Hawaldar, N. & Zhang, J. (2018) A comparative study of fabrication of sand casting mold using additive manufacturing and conventional proces. International Journal of Advanced Manufacturing Technology. 97(1-4), 1037-1045. DOI: 10.1007/s00170-018-2020-z.
[6] Upadhyay, M., Sivarupan, T. & El Mansori, M. (2017). 3D printing for rapid sand casting - A review. Journal of Manufacturing Processes. 29, 211-220. DOI: 10.1016/j.jmapro.2017.07.017.
[7] Zhang, Z., Wang, L., Zhang, L., Ma, P., Lu, B. & Du, C. (2021). Binder jetting 3D printing process optimization for rapid casting of green parts with high tensile strength. China Foundry. 18(4), 335-343. DOI: 10.1007/s41230-021-1057-z.
[8] Thiel, J., Ravi, S. & Bryan,t N. (2017). Advancements in materials for three-dimensional printing of molds and cores. International Journal of Metalcasting. 11(1), 3-13. DOI: 10.1007/s40962-016-0082-y.
[9] Mitra, S., Rodríguez de Castro A. & el Mansori, M. (2018). The effect of ageing process on three-point bending strength and permeability of 3D printed sand molds. International Journal of Advanced Manufacturing Technology. 97(1-4), 1241-1251, DOI: 10.1007/s00170-018-2024-8.
[10] Major-Gabryś, K., Hosadyna–Kondracka, M., Polkowska A., Warmuzek M. (2022). Effect of the biodegradable component addition to the molding sand on the microstructure and properties of ductile iron castings. Materials. 15(4), 1-14, DOI: 10.3390/ma15041552.
[11] Major-Gabryś, K. (2019) Environmentally friendly foundry molding and core sands. Journal of Materials Engineering and Performance. 28(7), 3905-3911, DOI: 10.1007/s11664-019-03947-x.
[12] Puzio, S., Kamińska, J., Major-Gabryś, K., Angrecki, M. & Hosadyna-Kondracka, M. (2019). Microwave-hardened moulding sands with hydrated sodium silicate for modified ablation casting. Archives of Foundry Engineering. 19(2), 91-96,
[13] Major-Gabryś, K., Grabarczyk, A. & Dobosz, St.M., (2018). Modification of foundry binders by biodegradable material. Archives of Foundry Engineering. 18(2), 31-44, DOI: 10.24425/122498.
[14] Major-Gabryś, K., Grabarczyk, A., Dobosz, St.M. & Jakubski, J. (2016). New bicomponent binders for foundry moulding sands composed of phenol-furfuryl resin and polycaprolactone. Metalurgija. 55(3), 385-387.
[15] Major-Gabryś, K. (2016). Odlewnicze masy formierskie i rdzeniowe przyjazne dla środowiska. Katowice-Gliwice: Archives of Foundry Engineering. (in Polish)
[16] Major-Gabryś, K., Stachurek, I. & Hosadyna-Kondracka, M. (2022). The influence of biomaterial in a binder composition on biodegradation of waste from furan moulding sands. Archives of Foundry Engineering. 22(2), 17-24, DOI: 10.24425/afe.2022.140.222
[17] Major-Gabryś, K., Hosadyna-Kondracka, M., Skrzyński, M. & Stachurek, I. (2022). The influence of biomaterial in the binder composition on the quality of reclaim from furan no-bake sands. Archives of Civil Engineering. 68(4), 163-177, DOI: 10.2445/ace.2022.143032.
[18] Major-Gabryś, K., Stachurek, I., Hosadyna-Kondracka, M. & Homa, M. (2022). The influence of polycaprolactone on structural changes of dusts from molding sands with resin-based binder before and after the biodegradation process. Polymers. 14(13), 1-16. DOI: 10.3390/polym14132605.
[19] Snelling, D., Williams, C. & Druschitz, A. (2014). A comparison of binder burnout and mechanical characteristics of printed and chemically sand molds. In 2014 International Solid Freeform Fabrication Symposium. University of Texas at Austin.
[20] Dana, H.R. & el Mansori, M. (2020). Mechanical characterisation of anisotropic silica sand/furan resin compound induced by binder jet 3D additive manufacturing technology. Ceramics International. 46(11), 17867-17880, DOI: 10.1016/j.ceramint.2020.04.093.
[21] Coniglio, N., Sivarupan, T. & el Mansori, M. (2018). Investigation of process parameter effect on anisotropic properties of 3D printed sand molds. International Journal of Advanced Manufacturing Technology. 94(5-8), 2175-2185. DOI: 10.1007/s00170-017-0861-5.
[22] Sivarupan, T., el Mansori, M., Daly, K., Mavrogordato, M.N. & Pierron, F. (2019) Characterisation of 3D printed sand moulds using micro-focus X-ray computed tomography. Rapid Prototyping Journal. 25(2), 404-416. DOI: 10.1108/RPJ-04-2018-0091.
[23] Cheng, Y., Li, Y., Yang, Y., Tang, K., Jhuang, F., L,i K. & Lu, C. (2022). Greyscale printing and characterization of the binder migration pattern during 3D sand mold printing. Additive Manufacturing. 56, 102929. DOI: 10.1016/j.addma.2022.102929.
[24] Vaezi, M. & Chua, C.K. (2011). Effects of layer thickness and binder saturation level parameters on 3D printing proces. International Journal of Advanced Manufacturing Technology. 53(1-4), 275-284. DOI: 10.1007/s00170-010-2821-1.
[25] Bryant, N., Frush, T., Thiel, J., MacDonald, E. & Walker, J. (2021). Influence of machine parameters on the physical characteristics of 3D-printed sand molds for metal casting. International Journal of Metalcasting. 15(2), 361-372. DOI: 10.1007/s40962-020-00486-3.
[26] Hackney, P.M. & Wooldridge, R. (2017). Characterisation of direct 3D sand printing process for the production of sand cast mould tools. Rapid Prototypin Journal. 23(1), 7-15. DOI: 10.1108/RPJ-08-2014-0101.
[27] Wang, Y., long Yu, R., kui Yin, S., Tan, R. & chun Lou, Y. (2021). Effect of gel time of 3D sand printing binder system on quality of sand mold/core. China Foundry. 18(6), 581-586. DOI: 10.1007/s41230-021-1085-8.
[28] Sama, S.R., Badamo, T. & Manogharan, G. (2020). Case studies on integrating 3D sand-printing technology into the production portfolio of a sand-casting foundry. International Journal of Metalcasting. 14(1), 12-24. DOI: 10.1007/s40962-019-00340-1.
[29] Triantaphyllou, A., Giusca, C., Macaulay, G., Reorig, F., Hoebel, M., Leach, R., Tomita, B. & Milne, K. (2015). Surface texture measurement for additive manufacturing. Surfdace Topografy: Metrology and Properties. 3(2), 024002. DOI: 10.1088/2051-672X/3/2/024002.
[30] Hartmann, C., van den Bosch, L., Spiegel, J., Rumschöttel, D. & Günther, D. (2022). Removal of stair-step effects in binder jetting additive manufacturing using grayscale and dithering-based droplet distribution. Materials. 15(11), 1-17. DOI: 10.3390/ma15113798.
[31] Deng, C., Kang, J., Shangguan, H., Huang, T., Zhang, X., Hu, Y. & Huang, T. (2018). Insulation effect of air cavity in sand mold using 3D printing technology. China Foundry. 15(1), 37-43. DOI: 10.1007/s41230-018-7243-y.
[32] Shangguan, H., Kang, J., Yi, J., Zhang, X., Wang, X., Wang, H. & Huang, T. (2018). The design of 3D-printed lattice-reinforced thickness-varying shell molds for castings. Materials. 11(4), 1-10. DOI: 10.3390/ma11040535.
[33] Wei, X., Wan, Y. & Liang, X. (2022). Effect of hollow core on cooling temperature in 3D printing. Journal of Physics: Conference Series. Institute of Physics. 2396, 012037, 1-9. DOI: 10.1088/1742-6596/2396/1/012037.
[34] ben Saada, M. & el Mansori, M. (2021). Assessment of the effect of 3D printed sand mold thickness on solidification process of AlSi13 casting alloy. The International Journal of Advanced Manufacturing Technology. 114, 1753-1766. DOI: 10.1007/s00170-021-06999-3.
[35] Sama, S.R., Wang, J. & Manogharan, G. (2018). Non-conventional mold design for metal casting using 3D sand-printing. Journal of Manufacturing Processes. 34, 765-775. DOI: 10.1016/j.jmapro.2018.03.049.
[36] Sama, S.R., Badamo, T., Lynch, P. & Manogharan, G. (2019). Novel sprue designs in metal casting via 3D sand-printing. Additive Manufacturing. 25, 563-578. DOI: 10.1016/j.addma.2018.12.009.
[37] Martinez, D., King, P., Sama, S.R., Sim, J., Toykoc, H. & Manogharan, G. (2023). Effect of freezing range on reducing casting defects through 3D sand-printed mold designs. International Journal of Advanced Manufacturing Technology. 126(1-2), 569-581. DOI: 10.1007/s00170-023-11112-x.
[38] Shuvo, M.M. & Manogharan, G. (2021). Novel riser designs via 3D sand printing to improve casting performance. Procedia Manufacturing. 53, 500-506. DOI: 10.1016/j.promfg.2021.06.052.
[39] Snelling, D., Williams, C. & Druschitz, A. (2019). Mechanical and material properties of castings produced via 3D printed mold. Additive Manufacturing. 27, 199-207, DOI: 10.1016/j.addma.2019.03.004.
[40] Hernández, F. & Fragoso, A. (2022). Fabrication of a stainless-steel pump impeller by integrated 3D sand printing and casting: mechanical characterization and performance study in a chemical plant. Applied Sciences (Switzerland). 12(7), 3539. DOI: 10.3390/app12073539.
[41] Szymański, P. & Borowiak, M. (2019). Evaluation of castings surface quality made in 3D printed sand moulds using 3DP technology. Lecture Notes in Mechanical Engineering. 201-212. DOI: 10.1007/978-3-030-16943-5_18.
[42] Skorulski, G. (2016). 3DP Technology for the manufacture of molds for pressure casting. Archives of Foundry Engineering. 16(3), 9-102. DOI: 10.1515/afe-2016-0058.
[43] Na, O., Kim, K. & Lee. H. (2021). Printability and setting time of csa cement with na2 sio3 and gypsum for binder jetting 3D printing. Materials. 14(11), 1-18. DOI: 10.3390/ma14112811.
[44] Zhang, L., Yang, X., Ran, S. Zhang, L., Hu, C. & Wang, H. (2023). Water-soluble sand core made by binder jetting printing with the binder of potassium carbonate solution. International Journal of Metalcasting. 1-12. DOI: 10.1007/s40962-022-00940-4.
[45] Goto, I., Kurosawa, K. & Matsuki, T. (2022). Effect of 3D-printed sand molds on the soundness of pure copper castings in the vicinity of as-cast surfaces. Journal of Manufacturing Processess. 77, 329-338. DOI: 10.1016/j.jmapro.2022.03.020.
[46] Castro-Sastre, M.Á., García-Cabezón, C., Fernández-Abia, A.I., Martín-Pedrosa, F. & Barreiro, J. (2021). Comparative study on microstructure and corrosion resistance of Al-Si alloy cast from sand mold and binder jetting mold. Metals (Basel). 11(9), 1421. DOI: 10.3390/met11091421.
[47] Kuchariková, L., Liptáková, T., Tillová, E., Kajánek, D., Schmidová, E. (2018). Role of chemical composition in corrosion of aluminum alloys. Metals. 8(8), 581. DOI: 10.3390/met8080581.
[48] Samuel, A.M., Doty, H.W., Valtierra, S. & Samuel, F.H. (2018). βAl5FeSi phase platelets-porosity formation relationship in A319.2 type alloys. International Journal of Metalcasting 12, 55-70. DOI: 10.1007/s40962-017-0136-9.
[49] Zheng, J., Chen, A., Yao, J., Ren, Y., Zheng, W., Lin, F., Shi, J., Guan, A. & Wang, W. (2022). Combination method of multiple molding technologies for reducing energy and carbon emission in the foundry industry. Sustainable Materials and Technologies. 34, e00522. DOI: 10.1016/j.susmat.2022.e00522.
[50] Kang, J. & Ma, Q. (2017). The role and impact of 3D printing technologies in casting. China Foundry. 14(3), 157-168. DOI: 10.1007/s41230-017-6109-z.
Go to article

Authors and Affiliations

Dawid Halejcio
1
ORCID: ORCID
Katarzyna Major-Gabryś
1
ORCID: ORCID

  1. AGH University of Krakow, Faculty of Foundry Engineering Department of Moulding Materials, Mould Technology and Non-ferrous Metals al. A. Mickiewicza 30, 30-059 Krakow
Download PDF Download RIS Download Bibtex

Abstract

An as-cast aluminum billet with a diameter of 100 mm has been successfully prepared from aluminum scrap by using direct chill (DC) casting method. This study aims to investigate the microstructure and mechanical properties of such as-cast billets. Four locations along a cross-section of the as-cast billet radius were evaluated. The results show that the structures of the as-cast billet are a thin layer of coarse columnar grains at the solidified shell, feathery grains at the half radius of the billet, and coarse equiaxed grains at the billet center. The grain size tends to decrease from the center to the surface of the as-cast billet. The ultimate tensile strength (UTS) and the hardness values obtained from this research slightly increase from the center to the surface of the as-cast billet. The distribution of Mg, Fe, and Si elements over the cross-section of the as-cast billet is inhomogeneous. The segregation analysis shows that Si has negative segregation towards the surface, positive segregation at the middle, and negative segregation at the center of the as-cast billet. On the other hand, the Mg element is distributed uniformly in small quantities in the cross-section of the as-cast billet.
Go to article

Bibliography

[1] Raabe, D., Ponge, D., Uggowitzer, P., Roscher, M., Paolantonio, M., Liu, C., Antrekowitsch, H., Kozeschnik, E., Seidmann, D., Gault, B., De Geuser, F., Dechamps, A., Hutchinson, C., Liu, C., Li, Z., Prangnell, P., Robson, J., Shanthraj, P., Vakili, S. & Pogatscher, S. (2022). Making sustainable aluminum by recycling scrap: The science of “dirty” alloys. Progress in Materials Science. 128, 1-150, 100947. DOI:10.1016/j.pmatsci.2022.100947.
[2] Jamaly, N., Haghdadi, N. & Phillion, A.B. (2015). Microstructure, macrosegregation, and thermal analysis of direct chill cast AA5182 aluminum alloy. Journal of Materials Engineering and Performance. 24, 2067-2073. DOI: 10.1007/s11665-015-1480-7.
[3] Vieth, P., Borgert, T., Homberg, W. & Grundmeier, G. (2022). Assessment of mechanical and optical properties of Al 6060 alloy particles by removal of contaminants. Advanced Engineering Materials. 25(3), 2201081. DOI: 10.1002/adem.202201081.
[4] Wagstaff, R.S., Wagstaff, B.R. & Allanore, A. (2017). Tramp element accumulation and its effects on secondary phase particles. The Minerals, Metals & Materials Society. 1097-1103. DOI: 10.1007/978-3-319-51541-0.
[5] Soo, V.K., Peeters, J., Paraskevas, D., Compston, P., Doolan, M. & Duflou, J.R. (2018). Sustainable aluminium recycling of end-of-life products: A joining techniques perspective. Journal of Cleaner Production. 178, 119-132. DOI: 10.1016/j.jclepro.2017.12.235.
[6] Al-Helal, K., Patel, J.B., Scamans, G.M. & Fan, Z. (2020). Direct chill casting and extrusion of AA6111 aluminum alloy formulated from taint tabor scrap. Materials. 13(24), 5740, 1-11. DOI: 10.3390/ma13245740.
[7] Graedel, T.E., Allwood, J., Birat, J.P., Buchert, M., Hagelüken, C., Reck, B.K., Sibley, S.F. & Sonnemann, G. (2011). What do we know about metal recycling rates? Journal of Industrial Ecology. 15(3), 355-366. DOI: 10.1111/j.1530-9290.2011.00342.x.
[8] Silva, M.S., Barbosa, C., Acselrad, O. & Pereira, L.C. (2004). Effect of chemical composition variation on microstructure and mechanical properties of AA 6060 aluminum alloy. Journal of Materials Engineering and Performance. 13, 129–134. DOI: 10.1361/10599490418307.
[9] Al-Helal, K., Lazaro-Nebreda, Patel, J. & Scamans, G. (2021). High-shear de-gassing and de-ironing of an aluminum. Recycling. 6 (66), 2-10. https://doi.org/10.1111/j.1530-9290.2011.00342.x.
[10] Zhang, L., Gao, J., Damoah, L.N.W. & Robertson, D.G. (2012). Removal of iron from aluminum: A review. Mineral Processing and Extractive Metallurgy Review. 33(2), 99-157. DOI: 10.1080/08827508.2010.542211.
[11] Zhang, L., Lv, X., Torgerson, A.T. & Long, M. (2011). Removal of impurity elements from molten aluminum: A review. Mineral Processing and Extractive Metallurgy Review. 32(3), 150-228. DOI: 10.1080/08827508. 2010.483396.
[12] Paraskevas, D., Kellens, K., Dewulf, W. & Duflou, J.R. (2015). Environmental modelling of aluminium recycling: A Life Cycle Assessment tool for sustainable metal management. Journal of Cleaner Production. 105, 357-370. DOI: 10.1016/j.jclepro.2014.09.102.
[13] Eskin, D.G., Savran, V.I. & Katgerman, L. (2005). Effects of melt temperature and casting speed on the structure and defect formation during direct-chill casting of an Al-Cu alloy. Metallurgical and Materials Transactions A. 36, 1965-1976. DOI: 10.1007/s11661-005-0059-6.
[14] Nadella, R., Eskin, D.G., Du, Q. & Katgerman, L. (2008). Macrosegregation in direct-chill casting of aluminium alloys. Progress in Materials Science. 53(3), 421-480. DOI: 10.1016/j.pmatsci.2007.10.001.
[15] Eskin, D.G. (2014). Mechanisms and Control of Macrosegregation in DC Casting. Light Metals 2014. 855-860. DOI: 10.1002/9781118888438.ch143.
[16] Mortensen, D., M’Hamdi, M., Ellingsen, K., Tveito, K., Pedersen, L. & Grasmo, G. (2014). Macrosegregation modelling of DC-casting including grain motion and surface exudation. Light Metals 2014. 867-872. DOI: 10.1002/9781118888438.ch145.
[17] Jolly, M., & Katgerman, L. (2022). Modelling of defects in aluminium cast products. Progress in materials science. 123, 1-39. DOI: 10.1016/j.pmatsci.2021.100824
[18] Suyitno, Kool, W.H. & Katgerman, L. (2005). Hot tearing criteria evaluation for direct-chill casting of an Al-4.5 pct Cu alloy. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. 36(6), 1537-1546. DOI: 10.1007/s11661-005-0245-6.
[19] Eskin, D.G., Zuidema, J., Savran, V.I. & Katgerman, L. (2004). Structure formation and macrosegregation under different process conditions during DC casting. Materials Science and Engineering A. 384(1-2), 232-244. DOI: 10.1016/j.msea.2004.05.066.
[20] Lalpoor, M., Eskin, D. G., Ruvalcaba, D., Fjær, H.G., Ten Cate, A., Ontijt, N. & Katgerman, L. (2011). Cold cracking in DC-cast high strength aluminum alloy ingots: An intrinsic problem intensified by casting process parameters. Materials Science and Engineering A. 528(6), 2831-2842. DOI: 10.1016/j.msea.2010.12.040.
[21] Grandfield, J.F., Eskin, D.G, Bainbridge, I.F. (2013). Direct-chill casting of light alloys. United States of America: John Wiley & Sons, Inc., Hoboken, New Jersey. DOI: 10.1002/9781118690734.
[22] Wang, R., Zuo, Y., Zhu, Q., Liu, X. & Wang, J. (2022). Effect of temperature field on the porosity and mechanical properties of 2024 aluminum alloy prepared by direct chill casting with melt shearing. Journal of Materials Processing Technology. 307, 117687. DOI: 10.1016/j.jmatprotec. 2022.117687.
[23] Barekar, N.S., Skalicky, I., Barbatti, C., Fan, Z. & Jarrett, M. (2021). Enhancement of chip breakability of aluminium alloys by controlling the solidification during direct chill casting. Journal of Alloys and Compounds. 862, 158008. DOI: 10.1016/j.jallcom.2020.158008.
[24] ASTM E112. (2010). Standard test methods for determining average grain size E112-10. ASTM E112-10. 96(2004), 1-27. DOI: 10.1520/E0112-10.
[25] Jones, S., Rao, A.K.P., Patel, J.B., Scamans, G.M. Fan, Z. (2012). Microstructural evolution in intensively melt sheared direct chill cast Al-alloys. In the 13th International Conference on Aluminum Alloys (ICAA13) 2013, (pp. 91-96). DOI: 10.1007/978-3-319-48761-8_15.
[26] Suyitno, A., Eskin, D.G., Savran, V.I. & Katgerman, L. (2004). Effects of alloy composition and casting speed on structure formation and hot tearing during direct-chill casting of Al-Cu alloys. Metallurgical and Materials Transactions A. 35 A(11), 3551-3561. DOI: 10.1007/s11661-004-0192-7.
[27] Turchin, A.N., Zuijderwijk, M., Pool, J., Eskin, D.G. & Katgerman, L. (2007). Feathery grain growth during solidification under forced flow conditions. Acta Materialia. 55(11), 3795-3801. DOI: 10.1016/j.actamat.2007.02.030.
[28] Liu, X., Zhu, Q., Jia, T., Zhao, Z., Cui, J. & Zuo, Y. (2020). As-cast structure and temperature field of direct-chill cast 2024 alloy ingot at different casting speeds. Journal of Materials Engineering and Performance. 29(10), 6840-6848. DOI: 10.1007/s11665-020-05140-x.
[29] Tian L., Guo, Y., Li, J., Xia, F., Liang, M. & Bai, Y.(2018) Effects of solidification cooling rate on the microstructure and mechanical properties of a cast Al-Si-Cu-Mg-Ni piston alloy. Materials. 11(7), 3-11. DOI: 10.3390/ma11071230.
[30] Suyitno. (2016). Effect of composition on the microporosity, microstructure, and macrostructure in the start-up direct-chill casting billet of Al-Cu alloys. ARPN Journal of Engineering and Applied Sciences. 11(2), 962-967. https://doi.org/10.1007/s11661-004-0192-7.
[31] Zhu, C., Zhao, Z. hao, Zhu, Q. feng, Wang, G. song, Zuo, Y. bo, & Qin, G. wu. (2022). Structures and macrosegregation of a 2024 aluminum alloy fabricated by direct chill casting with double cooling field. China Foundry. 19(1), 1-8. DOI: 10.1007/s41230-022-1030-5.
[32] Zheng, X., Dong, J. & Wang, S. (2018). Microstructure and mechanical properties of Mg-Nd-Zn-Zr billet prepared by direct chill casting. Journal of Magnesium and Alloys. 6(1), 95-99. DOI: 10.1016/j.jma.2018.01.003.
[33] Arif, A.F.M., Akhtar, S.S. & Sheikh, A.K. (2009). Effect of Al-6063 billet quality on the service life of hot extrusion die: metallurgical and statistical investigation. Journal of Failure Analysis and Prevention. 9, 253-261. DOI: 10.1007/s11668-009-9231-4.
[34] Triantafyllidis, G.K., Kiligaridis, I., Zagkliveris, D.I., Orfanou, I., Spyridopoulou, S., Mitoudi-Vagourdi, E. & Semertzidou, S. (2015). Characterization of the A6060 Al alloy mainly by using the micro-hardness vickers test in order to optimize the industrial solutionizing conditions of the as-cast billets. Material. Science and Applications. 06(01), 86-94. DOI: 10.4236/msa.2015.61011.
[35] Asensio-Lozano J., Suárez-Peña, B. & Voort, G.F.V. (2014). Effect of processing steps on the mechanical properties and surface appearance of 6063 aluminium extruded products. Materials. 7(6), 4224-4242. DOI: 10.3390/ma7064224.
[36] Založnik, M. & Šarler, B. (2005). Modeling of macrosegregation in direct-chill casting of aluminum alloys: Estimating the influence of casting parameters. Materials Science and Engineering A. 413-414, 85-91. DOI: 10.1016/j.msea.2005.09.056.
Go to article

Authors and Affiliations

Kardo Rajagukguk
1 2 4
ORCID: ORCID
Suyitno Suyitno
3 4
Harwin Saptoadi
1
I. K. Indraswari Kusumaningtyas
1
Budi Arifvianto
1 4
Muslim Mahardika
1 4

  1. Department of Mechanical and Industrial Engineering, Faculty of Engineering, Universitas Gadjah Mada, Jl. Grafika 2, Yogyakarta 55281, Indonesia
  2. Department of Mechanical Engineering, Institut Teknologi Sumatera (ITERA), Jl. Terusan Ryacudu, South Lampung, Lampung 35365, Indonesia
  3. Department of Mechanical Engineering, Faculty of Engineering, Universitas Tidar, Jl. Kapten Suparman 39, North Magelang, 56116, Indonesia
  4. Center for Innovation of Medical Equipment and Devices (CIMEDs), Universitas Gadjah Mada, Jl. Teknika Utara Yogyakarta 55281, Indonesia
Download PDF Download RIS Download Bibtex

Abstract

In order to clarify the action law of the swirl oxygen lance jet on the melt pool of the converter and to determine the optimal swirl angle of the swirl oxygen lance for the 120t converter, this study establishes the gas-liquid two-phase flow model of the oxygen lance with different swirl angles based on the realizable k-ε model and the VOF multiphase flow model. The gas-liquid interface behavior during the interaction between the jet and the molten pool was analyzed, and the flow pattern of molten steel in the molten pool was mainly investigated. The results show that compared with traditional oxygen lance, the rotating oxygen lance jet enhances the stirring of the melt pool and intensifies the fluctuation of the melt pool liquid level. The depth of the impact cavity decreases with the increase of the swirl angle, but the diameter of the impact cavity increases with the increase of the swirl angle. When the jet with a swirl angle of 10 ° impacts the surface of the melt pool, the turbulence energy obtained by the molten steel is the highest, the average flow velocity inside the melt pool is the highest, and the molten steel is stirred more thoroughly, achieving better melting effects.
Go to article

Bibliography

[1] Rao, J.P., Li, G.Q., & Yang, Z.Z. (2011). Research and application of new oxygen lance for BOF steelmaking. Advanced Materials Research. 335, 74-79. https://doi.org/10.4028/www.scientific.net/AMR.335-336.74.
[2] Allemand, B., Bruchet P. & Champinot, C. (2001). Theoretical and experimental study of supersonic oxygen jets. Industrial application in EAF. Metallurgical Research & Technology. 98(6), 571-587. https://doi.org/10.1051/ metal:2001107.
[3] Li, L., Li, M. & Shao, L. (2020). Physical and mathematical modeling of swirling gas jets impinging onto a liquid bath using a novel nozzles‐twisted lance. Steel Research International. 91(7), 54-60. https://doi.org/10.1002/ srin.201900684.
[4] Wang, X. (2022). Numerical simulation of jet characteristics and gas liquid two phase behavior of swirling oxygen lance. University of Science and Technology Liaoning. https://doi.org/10.26923/d.cnki.gasgc.2021.000081.
[5] Higuchi, Y. & Tago, Y. (2003). Effect of nozzle twisted lance on jet behavior and spitting rate in top blown process. ISIJ international. 43(9), 1410-1414. https://doi.org/10.2355 /isijinternational.43.1410.
[6] Li, M., Li, Q. & Kuang, S. (2016). Computational investigation of the splashing phenomenon induced by the impingement of multiple supersonic jets onto a molten slag–metal melt pool. Industrial & Engineering Chemistry Research. 55(12), 3630-3640. https://doi.org/10.1021/ acs.iecr.5b03301.
[7] Li, Q., Li, M. & Kuang, S, B. (2014). Computational study on the behaviours of supersonic jets and their impingement onto molten liquid free surface in BOF steelmaking. Canadian Metallurgical Quarterly. 53(3), 340-351. https://doi.org/10.1179/1879139514Y.0000000124.
[8] Li, M., Li, Q. & Zou Z. (2017). Computational investigation of swirling supersonic jets generated through a nozzle-twisted lance. Metallurgical and Materials Transactions B. 48, 713-725. https://doi.org/10.1007/s11663-016-0851-2.
[9] Muñoz-Esparza, D., Buchlin, J.M. & Myrillas, K. (2012). Numerical investigation of impinging gas jets onto deformable liquid layers. Applied Mathematical Modelling. 36(6), 2687-2700. https://doi.org/10.1016/j.apm.2011.09.052.
[10] Zhou, X., Ersson, M. & Zhong, L. (2014). Mathematical and physical simulation of a top blown converter. Steel research international. 85(2), 273-281. https://doi.org/10.1002/ srin.201300310.
[11] Hu, S., Zhu, R., & Dong, K. (2018). Effect of oxygen flow rate and temperature on supersonic jet characteristics and fluid flow in an EAF molten bath. Canadian Metallurgical Quarterly. 57(2), 219-234. https://doi.org/10.1080/00084433. 2017.1409945.
[12] Wang, W., Yuan, Z., & Matsuura, H. (2010). Three-dimensional compressible flow simulation of top-blown multiple jets in converter. ISIJ International. 50(4), 491-500. https://doi.org/10.2355/isijinternational.50.491.
[13] Li, M., Li, L. & Zhang, B. (2020). Numerical analysis of the particle-induced effect on gas flow in a supersonic powder-laden oxygen jet. Metallurgical and Materials Transactions B. 51, 1718-1730. https://doi.org/10.1007/s11663-020-01855-3.
[14] Feng, C., Zhu, R. & Dong, K. (2021). Effects of ambient temperature and powder gas ratio on jet characteristics of O2+ CO2 and CaO particles injected by a swirl-type oxygen lance nozzle. Powder Technology. 388, 537-553. https://doi.org/10.1016/j.powtec.2021.04.085.
[15] Lv, M., Zhu, R. & Wang H. (2013). Simulation and application of swirl-type oxygen lance in vanadium extraction converter. Steel Research International. 84(3), 304-312. https://doi.org/10.1002/srin.201200136.
[16] Lv, M., Zhu, R. & Guo, Y.G. (2013). Simulation of flowfluid in the BOF steelmaking process. Metallurgical and Materials Transactions B. 44, 1560-1571. https://doi.org/10.1007/ s11663-013-9935-4.
[17] Alam, M., Naser, J., & Brooks, G. (2010). Computational fluid dynamics simulation of supersonic oxygen jet behavior at steelmaking temperature. Metallurgical and Materials Transactions B. 41, 636-645. https://doi.org/10.1007/s11663-010-9341-0.
[18] Liu, F., Sun, D. & Zhu, R. (2017). Effect of nozzle twisted oxygen lance on flow field and dephosphorization rate in converter steelmaking process. Ironmaking & Steelmaking. 44(9), 640-648. https://doi.org/10.1080/03019233. 2016.1226562.
[19] Zhong, L., Zhu, Y. & Jiang, M. (2005). Cold modelling of slag splashing in LD furnace by oxygen lance with twisted nozzle tip. Steel Research International. 76(9), 611-615. https://doi.org/10.1002/srin.200506065.
[20] Liu, G., Liu, K., & Han, P. (2021). Splash sheet characteristics induced by the impingement of multiple jets in a steelmaking converter. Ironmaking & Steelmaking. 48(1), 25-32. https://doi.org/10.1080/03019233.2020.1720453.
Go to article

Authors and Affiliations

Haoran Ma
1
Guangqiang Liu
2
Chengcheng Xu
3
Kun Liu
1
ORCID: ORCID
Peng Han
1

  1. College of Materials and Metallurgy, University of Science and Technology Liaoning, Anshan 3114051, China
  2. College of Civil Engineering, University of Science and Technology Liaoning, Anshan 114051, China
  3. Cold rolling mill plant, ANGANG Steel Company Limited, Anshan 114021, China
Download PDF Download RIS Download Bibtex

Abstract

This study investigates image processing techniques for detecting surface cracks in spring steel components, with a focus on applications like Magnetic Particle Inspection (MPI) in industries such as railways and automotive. The research details a comprehensive methodology that covers data collection, software tools, and image processing methods. Various techniques, including Canny edge detection, Hough Transform, Gabor Filters, and Convolutional Neural Networks (CNNs), are evaluated for their effectiveness in crack detection. The study identifies the most successful methods, providing valuable insights into their performance. The paper also introduces a novel batch processing approach for efficient and automated crack detection across multiple images. The trade-offs between detection accuracy and processing speed are analyzed for the Morphological Top-hat filter and Canny edge filter methods. The Top-hat method, with thresholding after filtering, excelled in crack detection, with no false positives in tested images. The Canny edge filter, while efficient with adjusted parameters, needs further optimization for reducing false positives. In conclusion, the Top-hat method offers an efficient approach for crack detection during MPI. This research offers a foundation for developing advanced automated crack detection system, not only to spring sector but also extends to various industrial processes such as casting and forging tools and products, thereby widening the scope of applicability.
Go to article

Bibliography

[1] Gubeljak, N., Predan, J., Senčič, B. & Chapetti, M. (2014). Effect of residual stresses and inclusion size on fatigue resistance of parabolic steel springs. Materials Testing. 56(4), 312-317. DOI:10.3139/120.110567.
[2] Xu, C., Yilong L., Ming Y., Jiabang Y. & Xiang P. (2021). Effects of the ultra-sonic assisted surface rolling process on the fatigue crack initiation position distribution and fatigue life of 51CrV4 spring steel. Materials. 14(10), 2565, 1-19. DOI:10.3390/ma14102565.
[3] Yun, J.P., Choi, Dc., Jeon, Yj. et al., (2014). Defect inspection system for steel wire rods produced by hot rolling process. The International Journal of Advanced Manufacturing Technology. 70, 1625-1634. DOI:10.1007/s00170-013-5397-8.
[4] Perichiyappan, S. & Jagadeesha, T. (2021). Modelling and simulation of primary suspension springs used in Indian railways. Materials Today: Proceedings. 46(17), 8450-8454. DOI: 10.1016/j.matpr.2021.03.478.
[5] Kumar, S., Kumar, V., Nandi, R.K. et al. (2008). Investigation into surface defects arising in hot-rolled SUP 11A grade spring billets. Journal of Failure Analysis and Prevention. 8(6), 492-497. DOI:10.1007/s11668-008-9169-y.
[6] Filipović, M., Eriksson, C. & Överstam, H. (2006). Behaviour of surface defects in wire rod rolling. Steel research international. 77(6), 439-444, DOI:10.1002/srin.200606411.
[7] Matjeke, V.J., Van Der Merwe, J.W., Mukwevho, G. & Phasha, M.J. (2019). Thermal characteristics of spring steels used in railway bogies. SN Applied Sciences. 1, 1548, 1-8. DOI:10.1007/s42452-019-1546-5.
[8] Nagumo, Y., Tanifuji, K. & Imai, J. (2010). A basic study on wheel flange climbing using model wheelset. International Journal of Railway. 3(2), 60-67. DOI:10.1299/kikaic.74.242.
[9] The Rail Safety Inspection Office. (2021). Accident and incident investigation report: Derailment of the regional passenger train No. 21209 between Chvalkov and Vcelnicka operating control points. Retrieved November 7, 2023, from https://www.dicr.cz/files/uploads/Zpravy/MU/DI_Chvalkov_Vcelnicka_210715.pdf.
[10] Maass, M., Deutsch, W.A., Bartholomai, F. (2014). Magnetic Particle Inspection on train components. In 11th European Conference on Non-Destructive Testing, 6-11 October 2014 (pp. 1-9). Prague, Czech Republic.
[11] Deng, J., Singh, A., Zhou, Y., Lu, Y. & Lee, V.C.S. (2022). Review on computer vision-based crack detection and quantification methodologies for civil structures. Construction and Building Materials. 356, 129238. DOI:10.1016/j.conbuildmat.2022.129238.
[12] Mohan, A. & Poobal, S. (2018). Crack detection using image processing: A critical review and analysis. Alexandria Engineering Journal. 57(2), 787-798. DOI:10.1016/j.aej.2017.01.020.

Go to article

Authors and Affiliations

Marcin M. Marciniak
1

  1. Rzeszow University of Technology, Poland
Download PDF Download RIS Download Bibtex

Abstract

This article presents the results of research into the characteristics of cast steel alloyed with chromium and vanadium, subjected to heat treatment for increased strength parameters. In the first part, it discusses the state-of-the-art knowledge regarding technological developments in the field of cast-steel alloys and the influence of individual alloying additives on the microstructure and the properties of the steel alloy. Further sections present the results of microstructure observations performed with light microscopy, scanning electron microscopy, and transmission electron microscopy. This research focuses on the material in the state directly after casting and after heat treatment, which involved quenching and tempering at 200 °C. The microstructural analysis performed as part of this research has informed the discussion of the results obtained from tensile and impact strength tests. The article also includes the results of a fractography analysis performed as the final part of the tests and offers a general summary and conclusions.
Go to article

Bibliography

[1] Bartocha, D., Kilarski, J., Suchoń, J., Baron, C., Szajnar, J. & Janerka, K. (2011). Low-alloy constructional cast steel. Archives of Foundry Engineering. 11(spec.3), 265-271. ISSN (1897-3310). (in Polish).
[2] Skołek, E., Szwejkowska, K., Chmielarz, K., Świątnicki, W. A., Myszka, D. & Wieczorek, A.N. (2022). The microstructure of cast steel subjected to austempering and B-Q&P heat treatment. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. 53(7), 2544-2560. https://doi.org/10.1007/s11661-022-06685-3.
[3] Kniaginin, G. (1977). Cast steel: Metallurgy and foundry. Katowice: Wydawnictwo “Śląsk”. (in Polish).
[4] Sobula, S., Tęcza, G., Krasa, O. & Wajda, W. (2013). Grain refinement of low alloy Cr-Mn-Si-Ni-Mo cast steel with boron, titanium and rare elements additions. Archives of Foundry Engineering. 13(3) 153-156. ISSN (1897-3310). (in Polish).
[5] Gajewski, M. & Kasińska, J. (2012). Effects of Cr - Ni 18/9 austenitic cast steel modification by mischmetal. Archives of Foundry Engineering. 12(spec.4), 47-52. DOI: 10.2478/v10266-012-0105-y.
[6] Lazarova, R., Petrov, R.H., Gaydarova, V., Davidkov, A., Alexeev, A., Manchev, M. & Manolov, V. (2011). Microstructure and mechanical properties of P265GH cast steel after modification with TiCN particles. Materials & Design. 32(5), 2734-2741. DOI: 10.1016/J.MATDES.2011.01.024.
[7] Yang, S.Z. (2010). Vanadium Metallurgy. Beijing: Metallurgical Industry Press.
[8] Dobrzański, L.A. (2002). Fundamentals of materials science and metal science. Warszawa: Wydawnictwo Naukowo-Techniczne. (in Polish).
[9] Baoxiang, Y., Jinyong, H., Guifang, Z. & Jike, G. (2021). Applications of vanadium in the steel industry. Vanadium. 267-332. DOI: 10.1016/B978-0-12-818898-9.00011-5.
[10] Panin, S.V., Maruschak, P.O., Vlasov, I.V., Syromyatnikova, A.S., Bolshakov, A.M., Berto, F., Prentkovskis, O. & Ovechkin, B.B. (2017). Effect of operating degradation in arctic conditions on physical and mechanical properties of 09Mn2Si pipeline steel. Procedia Engineering. 178, 597-603. https://doi.org/10.1016/j.proeng.2017.01.117.
[11] Wyrzykowski, J.W., Pleszakow, E. & Sieniawski, J. (1999). Deformation and cracking of metals. Warszawa: Wydawnictwo Naukowo-Techniczne. (in Polish).
[12] Kocańda, S. (1972). Fatigue destruction of metals. Warszawa: Wydawnictwo: Naukowo-Techniczne. (in Polish).
[13] Maciejny, A. (1973). Brittleness of metals. Katowice: Wydawnictwo “Śląsk”. (in Polish).
[14] Kalandyk, B. & Zapała, R. (2008). Effect of heat treatment parameters on the properties of low-alloy cast steel with microadditions of vanadium. Archives of Foundry Engineering. 8(3), 137-140. ISSN(1897-3310).
[15] Kalandyk, B., Sierant, Z. & Sobula, S. (2009). Optimisation of microstructure, yield and impact strength of carbon cast steel by vanadium additions. Przegląd Odlewnictwa. 59(3), 108-113. (in Polish).
[16] Kalandyk, B. & Głownia, J. (2003). Influence of V and Mo and heat treatment of constructional Mn–Ni cast steels acquirement of yield strength above 850MPa. Archiwum Odlewnictwa. 3(8), 69-74. (in Polish). ISSN 1642-5308.
[17] Szajnar, J., Studnicki, A., Głownia, J., Kondracki, M., Suchoń, J. & Wróbel, T. (2013). Technological aspects of low-alloyed cast steel massive casting manufacturing. Archives of Foundry Engineering. 13(4), 97-102. ISSN (1897-3310).
[18] Sobula, S., Rąpała, M., Tęcza, G., & Głownia, J. (2009). Cast steels of a yield strength above 1300 MPa comparable to forgings. Przegląd Odlewnictwa. 59(3), 102-106. (in Polish).

Go to article

Authors and Affiliations

B. Białobrzeska
1
ORCID: ORCID

  1. Wrocław University of Technology, Poland
Download PDF Download RIS Download Bibtex

Abstract

The paper deals with the possibilities of using alkali silicate based inorganic binders for automotive industry aluminium castings production. In recent years, inorganic binders are coming back to the foreground and their manufacturers are developing new processes, which are starting to progressively supersede organic binder systems. Paper describes known knowledge about classic alkali silicate binders with focus on hardening processes and on improving their technological properties. Trends from the area of development and the use new alkali silicate based inorganic binders are also shortly described. As part of the experimental work, specific methods of producing samples were developed, with the help of which properties such as disintegration were subsequently evaluated by measuring abrasion and residual strengths. Characteristics such as residual compressive strength or shear strength at different thermal loads were also evaluated. When comparing the laboratory results with the results of de-coring in real conditions, a high degree of correlation was achieved, which makes it possible to determine the optimal recipe/procedure for the production of geometrically complex cores.
Go to article

Bibliography

[1] Jelínek, P. (1996). Foundry molding mixtures Part II, Binder systems of molding mixtures. Ostrava.
[2] Lewandowski, J.L. (1997) Plastics for casting molds. Kraków: WYD AKAPIT.
[3] Bolibruchova, D., Kuris, M., Matejka, M. & Kasinska, J. (2022). Study of the influence of zirconium, titanium and strontium on the properties and microstructure of AlSi7Mg0.3Cu0.5 alloy. Materials. 15(10). 3709, 1-20. DOI: 10.3390/ma15103709.
[4] Köhler, E., Klimesch, C., Bechtle, S. & Stanchev, S. (2010). Cylinder head production with gravity die casting. MTZ Worldwide. 71, 38-41. DOI: 10.1007/BF03227043. https://doi.org/10.1007/BF03227043.
[5] Polzin, H. (2014.) Inorganic Binders for mould and core production in the foundry. (1st. ed.) Berlin: Schiele und Schön.
[6] Antoš, P., Burian, A. (2002). Water glass - production, structure, properties and uses. Silchem
[7] Izdebska-Szanda, I., Palma, A., Angrecki, M. & Żmudzińska, M. (2013). Environmentally friendly mould technology. Archives of Foundry Engineering. 13(3), 37-42. DOI: 10.2478/afe-2013-0055.
[8] Stechman, M., Różycka, D. & Baliński, A. (2003). Modification of aqueous sodium silicate solutions with morphoactive agents. Polish Journal of Chemical Technology. 5(3), 47-50. ISSN (1509-8117).
[9] Jelínek, P. & Škuta, R. (2003). Modified sodium silicates – a new alternative for inorganic foundry binders. Materials Enginering. 10(3), 283.
[10] Mashifana, T. & Sithole, T. (2020). Recovery of silicon dioxide from waste foundry sand and alkaline activation of desilicated foundry sand. Journal of Sustainable Metallurgy. 6, 700-714. DOI: 10.1007/s40831-020-00303-5.
[11] Vasková, I. & Bobok, L. (2002). Some knowledge of the water glass modification by the phosphate compounds. Acta Metallurgica Slovaca. 8(2), 161-167.
[12] Major-Gabryś, K., Dobosz, St.M., Jelínek, P., Jakubski, J. & Beňo, J. (2014). The measurement of high-temperature expansion as the standard of estimation the knock-out properties of moulding sands with hydrated sodium silicate. Archives of Metallurgy and Materials. 59(2), 739-742. DOI: 10.2478/amm-2014-0123.
[13] Obzina, T., Merta, V., Folta, M., Bradáč, J., Beňo, J. Novohradská, N., et al. (2021). Technological and quality aspects of the use of innovative inorganic binders in the production of castings. Metals. 11(11), 1779, 1-13. DOI: 10.3390/met11111779.
[14] Izdebska-Szanda, I., Baliński, A., Angrecki, M. & Palma, A. (2014). The effect of nanostructure modification of the silicate binder on its binding characteristics and functional properties. Archives of Metallurgy and Materials. 59(3), 1033-1036. DOI: 10.2478/amm-2014-0173.
[15] Major-Gabryś, K., Dobosz, St.M., Jakubski, J. (2010). Self-hardened moulding sand with hydrated sodium silicate and liquid ester hardeners. In K. Świątkowski (Eds.), Polish Metallurgy in 2006-2010. (328-335). Krakow: Committee of Metallurgy of the Polish Academy of Science.
[16] Izdebska-Szanda, I. & Baliński, A. (2011). New generation of ecological silicate binders. Procedia Engineering. 10, 887-893. DOI: 10.1016/j.proeng.2011.04.146.
[17] Baliński, A. (2009). About structure of hydrated sodium silicate as a binder of moulding sands. Krakow: Foundry Research Institute.
[18] Izdebska-Szanda, I. (2012). Moulding sand with silicate binder characterized by beneficial technological and ecological properties. M.Sc. dissertation, Foundry Research Institute, Poland.
[19] Izdebska-Szanda, I., Stefański, Z., Pezraski, F. & Szolc, M. (2009). Effect of additives promoting the formation of lustrous carbon on the knocking out properties of foundry sands with new inorganic binders. Archives of Foundry Engineering. 9(1), 17 – 20.
[20] Izdebska-Szanda, I., Szanda, M. & Matuszewski, S. (2011). Technological and ecological studies of moulding sands with new inorganic binders for casting of non-ferrous metal alloys. Archives of Foundry Engineering. 11(1), 43-48. ISSN (1897-3310).
[21] Zaretskiy, L. (2016). Modified silicate binders new developments and applications. International Journal of Metalcasting. 10(1), 88-99. DOI: 10.1007/s40962-015-0005-3.
[22] Josan, A., Pinca‐Bretotean, C. & Ratiuc, S. (2021). Management of the regeneration process of the moulding mixtures in order to reduce the costs of the foundry type industrial enterprises. Materials Today: Proceedings. 45, 4161-4165. DOI: 10.1016/j.matpr.2020.12.034
[23] Davis, J.R. (1998). Metals Handbook. Desk Edition (2nd ed.) Boca Raton:CRC Press.
Go to article

Authors and Affiliations

M. Bruna
1
ORCID: ORCID
I. Vasková
2
ORCID: ORCID
M. Medňanský
1
ORCID: ORCID
P. Delimanová
2
ORCID: ORCID

  1. Faculty of Mechanical Engineering, Department of Technological Engineering, University of Zilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
  2. Institute Of Metallurgy, Faculty of Materials, Metallurgy and Recycling, Technical University of Košice, Letná 9, 042 00 Košice, Slovakia
Download PDF Download RIS Download Bibtex

Abstract

The paper presents the effect of electron beam alloying on the surface of a copper flat bar (M1Ez4) with titanium powder. Due to the quality of the surface after alloying and the obtained properties, the parameters used were given which met the assumed conditions to the greatest extent. The microstructure and mechanical properties as well as the chemical composition of surface-modified electron-beam copper show improved mechanical properties, i.e. hardness and abrasion resistance. This article uses research techniques using scanning electron microscopy and analysis of chemical composition in micro-areas (EDS). In order to examine the properties of the material after electron beam modification, hardness measurements were performed at low loads (HV0.1), abrasion resistance was tested, and conductivity was also measured. As a result of modifying the chemical and phase composition of M1E copper using an electron beam, the hardness increased by 46%, while the conductivity decreased by 16% due to the formation of intermetallic phases during solidification.
Go to article

Bibliography

[1] Węglowski, M.St., Błacha, S. & Phillips, A. (2016). Electron beam welding – Techniques and trends – Review. Vacuum. 130, 72-92. DOI: 10.1016/j.vacuum.2016.05.004.
[2] Yunlian, Q., Ju, D., Quan, H. & Liying, Z. (2000). Electron beam welding, laser beam welding and gas tungsten arc welding of titanium sheet. Materials Science and Engineering: A. 280(1), 177-181. DOI: 10.1016/S0921-5093(99)00662-0.
[3] Guo, S., Zhou, Q., Kong, J., Peng, Y., Xiang, Y., Luo, T., Wang, K. & Zhu, J. (2016). Effect of beam offset on the characteristics of copper/304stainless steel electron beam welding. Vacuum. 128, 205-212. DOI: 10.1016/j.vacuum.2016.03.034.
[4] Zhan, X., Yu, H., Feng, X., Pan, P. & Liu, Z. (2019). A comparative study on laser beam and electron beam welding of 5A06 aluminum alloy. Materials Research Express. 6(5), 056563. DOI: 10.1088/2053-1591/ab0562.
[5] Zhu, Q. et al., (2020). Research status and progress of welding technologies for molybdenum and molybdenum alloys. Metals. 10(2), 279, 1-16. DOI: 10.3390/met10020279.
[6] Pakieła, W. & Brytan, Z. (2020). Laser surface alloying of aluminum alloys with Cu/Fe metallic powders. Solid State Phenomena. 308, 64-75, DOI: 10.4028/www.scientific.net/SSP.308.64.
[7] Pakieła, W., Tański, T., Brytan, Z., Chladek, G. & Pakieła, K. (2020). The impact of laser surface treatment on the microstructure, wear resistance and hardness of the AlMg5 aluminum alloy. Applied Physics A. 126, 1-10. DOI: 10.1007/s00339-020-3350-x.
[8] Smolarczyk, P., Krupiński, M. & Pakieła, W. (2021). Microstructure and properties of the aluminum alloyed with ZrO powder using fiber laser. Solid State Phenomena. vol. 326, 157-165. DOI: 10.4028/www.scientific.net/ SSP.326.157.
[9] Janicki, D., Górka, J., Kwaśny, W., Pakieła, W. & Matus, K. (2020). Influence of solidification conditions on the microstructure of laser-surface-melted ductile cast iron. Materials. 13(5), 1174, 1-13. DOI: 10.3390/ma13051174.
[10] Krupiński, M., Krupińska, B. & Chulist, R. (2023). Influence of Re on the plastic hardening mechanism of alloyed copper. Materials. 16(16), 5519, 1-13. DOI: 10.3390/ma16165519.
[11] Krupińska, B., Rdzawski, Z., Krupiński, M. & Pakieła, W. (2020). Precipitation Strengthening of Cu–Ni–Si Alloy. Materials. 13(5), 1182, 1-12. DOI: 10.3390/ma13051182.
[12] Caron, R.N. (2001). Copper Alloys: Properties and Applications. In Buschow, K.H.J., Cahn, R.W., Flemings, M.C., Ilschner, B., Kramer, E.J., Mahajan, S. & Veyssière, P. (Eds.), Encyclopedia of Materials: Science and Technology (pp. 1665-1668). Oxford: Elsevier.
[13] Patidar, D. & Rana, R.S. (2018). The effect of CO2 laser cutting parameter on Mechanical & Microstructural characteristics of high strength steel-a review. Materials Today: Proceedings. 5(9), Part 3, 17753-17762. DOI: 10.1016/j.matpr.2018.06.099.
[14] Kusinski, J., Kac, S., Kopia, A., Radziszewska, A., Rozmus-Górnikowska, M., Major, B., Major, L., Marczak, J. & Lisiecki, A. (2012). Laser modification of the materials surface layer – a review paper. Bulletin of the Polish Academy of Sciences: Technical Sciences. 60(4), 711-728. DOI: 10.2478/v10175-012-0083-9.
[15] Valkov, S., Ormanova, M. & Petrov, P.(2020). Electron-beam surface treatment of metals and alloys: techniques and trends. Metals. 10(9), 1219, 1-20. DOI: 10.3390/met10091219.
[16] Körner, C. (2016). Additive manufacturing of metallic components by selective electron beam melting — a review. International Materials Reviews. 61(5), 361-377. DOI: 10.1080/09506608.2016.1176289.
[17] Krupiński, M., Smolarczyk, P.E. & Bonek, M. (2020). Microstructure and properties of the copper alloyed with Ag and Ti powders using fiber laser. Materials. 13(11), 2430, 1-13. DOI: 10.3390/ma13112430.
[18] Božić, D., Stasic, J., Dimcic, B., Vilotijevic, M. & Rajkovic, V. (2011). Multiple strengthening mechanisms in nanoparticle-reinforced copper matrix composites. Bulletin of Materials Science. 34, 217-226. DOI: 10.1007/s12034-011-0102-8.
[19] Ran, Q., Liu, J., Wang, X. & Liu, J. (2021). The Effect of Heat Treatment on the Microstructure Evolution and Properties of an Age-Hardened Cu-3Ti-2Mg Alloy. Archives of Metallurgy and Materials. 66(1), 163-170. DOI: 10.24425/amm.2021.134772. https://journals.pan.pl/dlibra/publication/134772/edition/117801
Go to article

Authors and Affiliations

P.E. Smolarczyk
1
ORCID: ORCID
M. Krupiński
1
ORCID: ORCID
M. Węglowski
2
ORCID: ORCID
Wojciech Pakieła
1
ORCID: ORCID
P. Śliwiński
2
ORCID: ORCID

  1. Department of Engineering Materials and Biomaterials, Silesian University of Technology, Konarskiego 18A, 44-100 Gliwice, Poland
  2. Łukasiewicz Research Network – Upper Silesian Institute of Technology, Bł. Czesława 16-18, 44-100 Gliwice, Poland
Download PDF Download RIS Download Bibtex

Abstract

Predicting the permeability of different regions of foundry cores and molds with complex geometries will help control the regional outgassing, enabling better defect prediction in castings. In this work, foundry cores prepared with different bulk properties were characterized using X-ray microtomography, and the obtained images were analyzed to study all relevant grain and pore parameters, including but not limited to the specific surface area, specific internal volume, and tortuosity. The obtained microstructural parameters were incorporated into prevalent models used to predict the fluid flow through porous media, and their accuracy is compared with respect to experimentally measured permeability. The original Kozeny model was identified as the most suitable model to predict the permeability of sand molds. Although the model predicts permeability well, the input parameters are laborious to measure. Hence, a methodology for replacing the pore diameter and tortuosity with simple process parameters is proposed. This modified version of the original Kozeny model helps predict permeability of foundry molds and cores at different regions resulting in better defect prediction and eventual scrap reduction.
Go to article

Bibliography

[1] Jorstad, J., Krusiak, M.B., Serra, J.O., La Fay, V. (2018). Aggregates and binders for expendable molds. Casting. 528-548. https://doi.org/10.31399/asm.hb.v15.a0005242.
[2] Campbell, J., Svidró, J.T. & Svidró, J. (2017). Molding and Casting Processes. In Doru M. Stefanescu (Eds.), Cast Iron Science and Technology (pp. 189-206). ASM International. https://doi.org/10.31399/asm.hb.v01a.a0006297.
[3] Ramakrishnan, R., Griebel, B., Volk, W., Günther, D. & Günther, J. (2014). 3D printing of inorganic sand moulds for casting applications. Advanced Materials Research. 1018, 441-449. https://doi.org/10.4028/www.scientific.net/AMR.1018.441.
[4] Dańko, R. & Jamrozowicz, Ł. (2017). Density distribution and resin migration investigations in samples of sand core made by blowing method. Journal of Casting & Materials Engineering. 1(3), 70-73. https://doi.org/10.7494/ jcme.2017.1.3.70.
[5] Lannutti, J.J., Mobley, C.E. (2003). Improvements in Sand Mold/Core Technology: Effects on Casting Finish. Final Technical Report, The Ohio State University, Columbus, OH.
[6] Korotchenko, A.Y., Khilkov, D.E., Khilkova, A.A. & Tverskoy, M.V. (2020). Improving the quality of production of sand core on core shooting machines. Materials Science Forum. 989, 589-594. https://doi.org/10.4028/www.scientific.net/MSF.989.589.
[7] Winartomo, B., Vroomen, U., Bührig-Polaczek, A. & Pelzer, M. (2005). Multiphase modelling of core shooting process. International Journal of Cast Meterials Research. 18(1), 13-20. https://doi.org/10.1179/136404605225022811.
[8] Thorborg, J., Wendling, J., Klinkhammer, J., Heitzer, M. (2023). Modelling hot distortion of inorganic bonded sand cores and application on complex 3D printed automotive cores, IOP Conference Series: Materials Science and Engineering. 1281(1), 012069. https://doi.org/10.1088/1757-899x/1281/1/012069.
[9] Muskat, M. (1937). The flow of fluids through porous media, Journal of Applied Physics. 8(4), 274-282. https://doi.org/10.1063/1.1710292.
[10] Campbell, J. (2011). Molds and cores. Complete Casting Handbook. 1, 155-186. https://doi.org/10.1016/b978-1-85617-809-9.10004-0.
[11] Marks, B., Sandnes, B., Dumazer, G., Eriksen, J.A. Måløy, K.J. (2015). Compaction of granular material inside confined geometries, Frontiers in Physics. 3, 1-9. https://doi.org/10.3389/fphy.2015.00041.
[12] Bargaoui, B., Azzouz, F., Thibault, D. & Cailletaud, G. (2017). Thermomechanical behavior of resin bonded foundry sand cores during casting. Journal of Materials Processing Technology. 246, 30-41. https://doi.org/10.1016/j.jmatprotec. 2017.03.002.
[13] Mitra, S., EL Mansori, M., Rodríguez de Castro, A. & Costin, M. (2020). Study of the evolution of transport properties induced by additive processing sand mold using X-ray computed tomography. Journal of Materials Processing Technology. 277 116495. https://doi.org/10.1016/ j.jmatprotec.2019.116495.
[14] Ettemeyer, F., Lechner, P., Hofmann, T., Andrä, H., Schneider, M., Grund, D., Volk, W. & Günther, D. (2020). Digital sand core physics: Predicting physical properties of sand cores by simulations on digital microstructures. Internatiol Journal of Solids Structures. 188-189, 155-168. https://doi.org/10.1016/j.ijsolstr.2019.09.014.
[15] Neithalath, N., Sumanasooriya, M.S. & Deo, O. (2010). Characterizing pore volume, sizes, and connectivity in pervious concretes for permeability prediction. Materials Characterization 61(8), 802-813. https://doi.org/10.1016/j.matchar.2010.05.004.
[16] Das, S., Stone, D., Convey, D. & Neithalath, N. (2014). Pore- and micro-structural characterization of a novel structural binder based on iron carbonation, Materials Characterization. 98, 168-179. https://doi.org/10.1016/j.matchar.2014.10.025.
[17] Landis, E.N. & Keane, D.T. (2010). X-ray microtomography. Materials Characterization. 61(12), 1305-1316. https://doi.org/10.1016/j.matchar.2010.09.012. [18] Scheidegger, A.E.. (1957). The physics of flow through porous media. University of Toronto press.
[19] H. Darcy. (1856). Les fontaines publiques de la ville de Dijon: exposition et application des principes à suivre et des formules à employer dans les questions de distribution d’eau. Paris.
[20] da Silva, M.T.Q.S., do Rocio Cardoso, M., Veronese, C.M.P. & Mazer, W. (2022). Tortuosity: A brief review. Materials Today: Proceedings. 58(4), 1344-1349. https://doi.org/10.1016/j.matpr.2022.02.228.
[21] Kadhim, F.S., Samsuri, A. & Kamal, A. (2013). A review in correlations between cementation factor and carbonate rocks properties. Life Science Journal. 10(4), 2451-2458.
[22] Nield, D.A., Bejan, A. (2012). Convection in porous media: Springer Fourth edition. https://doi.org/10.1007/978-1-4614-5541-7.
[23] Costa, A. (2006). Permeability-porosity relationship: A reexamination of the Kozeny-Carman equation based on a fractal pore-space geometry assumption. Geophysical Research Letters. 33(2), 1-5. https://doi.org/10.1029/2005GL025134.
[24] Slichter, C.S. (1899). Theoretical investigation of the motion of ground waters. Geological Survey (U.S.). Ground Water Branch.
[25] Leibenzon, L.S. (1947). Dvizhenie prirodnykh zhidkostei i gazov v poristoi srede. In The Motion of Natural Liquids and Gases in a Porous Medium. Gostekhizdat, Moscow.
[26] Sundaram, D., Svidró, J.T., Svidró, J. & Diószegi, A. (2021). On the relation between the gas-permeability and the pore characteristics of furan sand. Materials. 14(14), 3803, 1-14. https://doi.org/10.3390/ma14143803.
[27] Sundaram, D., Svidró, J.T., Svidró, J. & Diószegi, A. (2022). A novel approach to quantifying the effect of the density of sand cores on their gas permeability. Joranl of Casting & Materials Engineering. 6(2), 33-38. https://doi.org/10.7494/jcme.2022.6.2.33.
[28] Costanza-Robinson, M.S. Estabrook, B.D. & Fouhey, D.F. (2011). Representative elementary volume estimation for porosity, moisture saturation, and air-water interfacial areas in unsaturated porous media: Data quality implications. Water Resources Reserch. 47(7), 1-12. https://doi.org/10.1029/2010WR009655.
[29] Schindelin, J., Arganda-Carreras, I., Frise, E., Kaynig, V., Longair, M., Pietzsch, T., Preibisch, S., Rueden, C., Saalfeld, S., Schmid, B., Tinevez, J.-Y., White, D.J., Hartenstein, V., Eliceiri, K., Tomancak, P. & Cardona, A. (2012). Fiji: an open-source platform for biological-image analysis. Nature Methods. 9, 676-682. https://doi.org/10.1038/nmeth.2019.
[30] Grace, J.R., Ebneyamini, A. (2021). Connecting particle sphericity and circularity. Particuology. 54, 1-4. https://doi.org/10.1016/j.partic.2020.09.006.
[31] Vincent, L., Soille, P. (1991). Watersheds in digital spaces: an efficient algorithm based on immersion simulations. IEEE Transactions on Pattern Analysis & Machine Intelligence. 13(06), 583-598. https://doi.org/10.1109/34.87344.
[32] Domander, R. Felder, A.A., Doube, M., Schmidt, D. (2021). BoneJ2 - refactoring established research software. Wellcome Open Research. 6, 1–21.
[33] Dougherty, R., Kunzelmann, K.-H. (2007). Computing Local Thickness of 3D Structures with ImageJ. Microscopy Microanalysis. 13(S02), 1678-1679. https://doi.org/10.1017/ s1431927607074430.
[34] Schmid, B., Schindelin, J., Cardona, A., Longair, M. & Heisenberg, M. (2010). Open Access SOFTWARE A high-level 3D visualization API for Java and ImageJ. BMC Bioinformatics. 11, 274, 1-7. http://www.biomedcentral.com /1471-2105/11/274.
[35] Nimmo, J.R. (2004). Porosity and Pore Size Distribution. In Hillel, D.(Eds.), Encyclopedia of Soils in the Environment. London, Elsevier,.
[36] Glover, P.W.J., Walker, E. (2009). Grain-size to effective pore-size transformation derived from electrokinetic theory. Geophysics. 74(1), E17-E29. https://doi.org/10.1190/ 1.3033217.
[37] Graton, L.C. & Fraser, H.J. (1935). Systematic Packing of spheres: with particular relation to porosity and permeability. The Journal of Geology. 43(8), 1, 785-909. http://www.jstor.org/stable/30058420.
[38] Holzer, L., Marmet, P., Fingerle, M., Wiegmann, A., Neumann, M., Schmidt, V. (2023). Tortuosity and microstructure effects in porous media. Springer Cham. https://doi.org/10.1007/978-3-031-30477-4.
Go to article

Authors and Affiliations

D. Sundaram
1
ORCID: ORCID
T. Matsushita
1
ORCID: ORCID
I. Belov
1
A. Diószegi
1
ORCID: ORCID

  1. School of Engineering, Jönköping University, Sweden
Download PDF Download RIS Download Bibtex

Abstract

The current trend of continuous improvement of various components constantly pushes the development of new materials forward. The basic goal of research into new and better materials is to improve their properties compared to the original material. One of the essential properties of the newly developed aluminum alloys is their resistance to the formation of tearing. Tears appear during the solidification of the casting and break the integrity due to tension arising while cooling. Several factors influence the susceptibility to tearing, but they can be minimized and reduce the chance of their occurrence. As part of the experiment, the AlSi5Cu2Mg alloy was evaluated in four material variants, without additives (in the reference state), with the addition of transition elements Zr, Ti and their combination Zr + Ti. Susceptibility to the formation of teras was assessed using a qualitative method supplemented by microscopic analysis of the tear profile and determination of the dendritic coherence temperature. The evaluation shows that the addition of Zr increased the susceptibility to tear formation. On the contrary, the addition of Ti had a positive effect and reduced the susceptibility to the formation of tears. The effect of the addition of Zr and Ti in the AlSi5Cu2Mg alloy showed a similar values as without the addition of alloys (reference condition). Microstructural analysis of the tear profile pointed to the negative influence of phases rich in Zr. The subsequent evaluation of the dendritic coherence temperature of individual AlSi5Cu2Mg alloys did not show a correlation with the results of a quantitative evaluation of susceptibility to tears.
Go to article

Bibliography

[1] Bolibruchová, D. (2010). Foundry technology. Žilina: vydavateľstvo GEORG, ISBN 978-80-89401-14-7.
[2] Pastirčák, R., Bolibruchová, D., Sládek, A. (2015). Foundry theory. Žilina: EDIS-vydavateľské centrum ŽU, ISBN 978-80-554-1096-8.
[3] Wu, Q., (2012). Study of Hot Tearing in Cast and Wrought Aluminum Alloys. Dissertation thesis. Worchester: Faculty of the Worcester polytechnic institute, UK.
[4] Bruna, M. & Galčík, M. (2021). Casting Quality Improvement by Gating System Optimization. Archives of Foundry Engineering. 21(1). 132-136. DOI:10.24425/afe.2021.136089.
[5] Huang, H., Fu, P, Wang, Y., Peng, L. & Jiang, H. (2014). Effect of pouring and mold temperatures on hot tearing susceptibility of AZ91D and Mg–3Nd–0.2Zn–Zr Mg alloys. Transactions of Nonferrous Metals Society of China. 24(4), 922-929. DOI:10.1016/S1003-6326(14)63144-7.
[6] Campbell, J. (2015). Complete casting handbook: metal casting processes, metallurgy, techniques and design. Elsevier Science.
[7] Oh, S.H., A.H., Munkhdelger, Ch. & Kim, H.J. (2021). Effect of Cu content on hot tearing susceptibility in al-si-cu aluminum casting alloy. Journal of Korea Foundry Society. 41(5), 419-433.
[8] Bichler, L., Elsayed, A., Lee, K. & Ravindran, C. (2008). Influence of mold and pouring temperatures on hot tearing susceptibility of AZ91D magnesium alloy. International Journal of Metalcasting. 2, 43-54. DOI:10.1007/BF03355421.
[9] Hasan, A. & Suyitno, A. (2014). Effect pouring temperature on casting defect susceptibility of hot tearing in metal alloy Al-Si. Applied Mechanics and Materials. 758, 95-99. https://doi.org/10.4028/www.scientific.net/AMM.758.95.
[10] Djurdjevic, M.B. Sokolowski, J.H. & Odanovic Z. (2012). Determination of dendrite coherency point characteristics using first derivative curve versus temperature. Journal of Thermal Analysis and Calorimetry volume. 109(2), 875-882. https://doi.org/10.1007/s10973-012-2490-4.
[11] Gómez, I. V., Viteri, E. V. Montero, J., Djurdjevic, M. & Huber, G. (2018). The determination of dendrite coherency point characteristics using three new methods for aluminum alloys. Applied Sciences. 8(8), 1236, 1-14. https://doi.org/10.3390/app8081236.
[12] Bolibruchová, D., Širanec, L. & Matejka, M. (2022). Selected properties of a Zr-containing AlSi5Cu2Mg alloy intended for cylinder head castings. Materials. 15(14), 4798, 1-16. https://doi.org/10.3390/ma15144798
[13] Bolibruchová, D., Kuriš, M., Matejka, M. & Kasińska, J. (2022). Study of the influence of zirconium, titanium and strontium on the properties and microstructure of AlSi7Mg0.3Cu0.5 alloy. Materials. 15(10), 3709, 1-20. https://doi.org/10.3390/ma15103709.
Go to article

Authors and Affiliations

M. Matejka
1
ORCID: ORCID
D. Bolibruchová
1
ORCID: ORCID
E. Kantoríková
1
ORCID: ORCID

  1. University of Zilina, Faculty of Mechanical Engineering, Department of Technological Engineering, Slovak Republic
Download PDF Download RIS Download Bibtex

Abstract

During the casting cycle, the relatively cold material of the mold comes into contact with the significantly higher temperature melt, which causes high temperature fluctuations on the face of the mold and in its volume, which cause cyclic temperature stress. The submitted article is based on conclusions of the article “Evaluation of the temperature distribution of a die casting mold of X38CrMoV5_1 steel”, in which the modification of temperature relations of the mold in the direction from the mold face to its volume was investigated. In current article, the influence of the tempering channel distance on the temperature modification in the volume of high pressure die casting mold is investigated. Three variants of the tempering channels placements with different location respecting the mold cavity were investigated. The temperature was monitored in two selected locations, with distribution of 1mm, 2mm, 5mm, 10mm and 20mm in the direction from the mold cavity surface to the volume of fixed and movable part of the mold. As a comparative parameter, the temperature of the melt in the center of the runner above the measuring point and the temperature of the melt close to the face of the mold were monitored. The measurement was performed using Magmasoft simulation software. It was discovered that up to a distance of 5mm from the face of the mold, a zone with complete heat transit without its accumulation occurs. Above this limit, the mold begins to accumulate heat, and from distance of 20mm from the face of the mold, the heat gradually passes into the entire mass of the mold without significant temperature fluctuations. The propositions derived from the results of the experiments presented at the end of the article will subsequently be experimentally verified in further research works.
Go to article

Bibliography

[1] Ebrahimi, A., Fritsching, U., Heuser, M., Lehmhus, D., Struß, A., Toenjes, A., von Hehl, A. (2020). A digital twin approach to predict and compensate distortion in a High Pressure Die Casting (HPDC) process chain. In Proceedings of the 5th International Conference on System-Integrated Intelligence, 11-13 November 2020 (pp. 144-149). Bremen: Elsevier B.V. DOI: 10.1016/j.promfg.2020.11.026.
[2] Bi, C., Gou, Z. & Xiong, S. (2015). Modeling and simulation for die casting mould filling process using cartesian cut cell approach. International Journal of Cast Metals Research. 28(4), 234-241. DOI: 10.1179/1743133615Y.0000000006.
[3] Choi, J., et al. (2022). Fatigue life prediction methodology of hot work tool steel dies for high-pressure die casting based on thermal stress analysis. Metals. 12(10), 1744, 1-18. DOI: 10.3390/met12101744.
[4] Cao, H., Shen, C., Wang, C., Xu, H. & Zhu, J. (2019). Direct observation of filling process and porosity prediction in high pressure die casting. Materials. 12(7), 1099, 1-19. DOI: 10.3390/ma12071099.
[5] Yu, W., Liang, S., Cao, Y.Y., Li, X.B., Guo, Z.P. & Xiong, S.M. (2017). Interfacial heat transfer behavior at metal/die in finger-plated casting during high pressure die casting process. China Foundry. 14(4), 258-264. DOI: 10.1007/s41230-017-6066-6.
[6] Jiao, X., Liu, C., Wang, J., Guo, Z., Wang, J., Wang, Z., Guo, J. & Xiong, S. (2020). On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 wt%Si alloy. Progress in Natural Science: Materials International. 30(2), 221-228. DOI: 10.1016/j.pnsc.2019.04.008.
[7] Iwata, Y., Dong, S., Sugiyama, Y. & Iwahori, H. (2014). Change in molten metal pressure and its effect on defects of aluminum alloy die castings. Materials Transactions. 55(2), 311-317. DOI: 10.2320/matertrans.F-M2013838.
[8] Majernik, J. & Podaril. M. (2019). Evaluation of the temperature distribution of a die casting mold of X38CrMoV5_1 steel. Archives of Foundry Engineering. 19(2), 107-112. DOI: 10.24425/afe.2019.127125.
[9] Ružbarský, J., Paško, J., & Gašpár, Š. (2014). Technigques of Die Casting. Lüdenscheid: RAM-Verlag.
[10] Trytek, A. Orłowicz, A.W., Tupaj, M., Mróz, M., Markowska, O., Bąk, G. & Abram, T. (2016) The effect of a thin-wall casting mould cavity filling conditions on the casting surface quality. Archives of Foundry Engineering. 16(4), 222-226. DOI: 10.1515/afe-2016-0113.
[11] Gašpár, Š., Paško, J., & Majerník, J. (2017). Infuence of Structure Adjustment of Gating System of Casting Mould upon the Quality of Die Cast. Lüdenscheid: RAM-Verlag.
[12] Noga, P., Tuz, L., Żaba, K. & Zwoliński, A. (2021). Analysis of microstructure and mechanical properties of alsi11 after chip recycling, co-extrusion, and arc welding. Materials. 14(11), 3124, 1-22. DOI: 10.3390/ma14113124.
[13] Majernik, J. Gaspar, S., Podaril, M. & Coranic, T. (2020). Evaluation of thermal conditions at cast-die casting mold interface. MM Science Journal. 2020(November), 4112-4118. DOI: 10.17973/MMSJ.2020_11_2020041.
[14] Karková, M., Majerník, J. & Kmec, J. (2017). Analysis of influencing the macrostrukture and hardness of casting surface layer by changing conditions of crystallization. MM Science Journal. 1910-1913. DOI: 10.17973/MMSJ.2017_12_201720.
[15] Gašpár, Š., Pasko, J., Malik, J., Panda, A., Jurko, J. & Maseenik, J. (2012). Dependence of pressure die casting quality on die casting plunger velocity inside a filling chamber of a pressure die casting machine. Advanced Science Letters. 14(1), 499-502. DOI: 10.1166/asl.2012.3989.
Go to article

Authors and Affiliations

J. Majerník
1
ORCID: ORCID
M. Podaril
1
ORCID: ORCID
M. Majernikova
1

  1. Institute of Technology and Business in České Budějovice, Czech Republic
Download PDF Download RIS Download Bibtex

Abstract

The surface temperature of steel billets during hot rolling can reach up to 1200 °C. High temperature promotes rapid oxidation of the surface of steel billets, forming a dense oxide layer similar to fish scales. If not removed in a timely manner, it will damage the surface of the steel billets and exacerbate the wear of the rolls during the descaling process. There are many methods for descaling, but high-pressure water jet has become the main method for descaling due to its excellent descaling performance, low cost, and ease of use. The tip of the descaling nozzle serves as the main component, and its structural parameters affect the final descaling effect. This research changes the shape factor of the nozzle groove curve and the diameter of the nozzle throat, and performs computational fluid dynamics (CFD) simulations on the simplified nozzle external flow field. The axial velocity at the center of the jet generates a velocity peak at 0.5-1 Dc. The peak velocity increases with the increase of shape factor and throat diameter, and the influence of shape factor on the peak velocity is greater. For a constant target distance, the length of the velocity stable section along the jet impact line increases with the increase of the shape factor. The maximum value of dynamic pressure increases, and the smaller the target distance, the greater the dynamic pressure difference. The trend of water volume is roughly the same as that of dynamic pressure.
Go to article

Bibliography

[1] Ma, F., Li, Y. & Song, Z. M. (2011). Jet performance testing of high-pressure waterjet descaling nozzles. Advanced Materials Research. 314, 2408-2413. https://doi.org/10.4028/www.scientific.net/AMR.314-316.2408.
[2] Baofu Kou, Pengliang Huo, Xiaohua Hou, (2020). Research on the influence of external parameters of fan-type nozzle on water jet performance. Shock and Vibration. 2020, 4386259, 1-16. https://doi.org/10.1155/2020/4386259.
[3] Jiang, T., Huang, Z., Li, J., Zhou, Y. & Xiong, C. (2022). Effect of nozzle geometry on the flow dynamics and resistance inside and outside the cone-straight nozzle. ACS omega. 7(11), 9652-9665. https://doi.org/10.1021/acsomega.1c07050.
[4] Sushma, L., Deepik, A. U., Sunnam, S. K. & Madhavi, M. (2017). CFD investigation for different nozzle jets. Materials Today: Proceedings. 4(8), 9087-9094. https://doi.org/10.1016/j.matpr.2017.07.263.
[5] Gu, B., Hu, R., Wang, L., & Xu, G. (2022). Study on the influence rule of high-pressure water jet nozzle parameters on the effect of hydraulic slotting. Geofluids. 2022, 4510194. https://doi.org/10.1155/2022/4510194.
[6] Frick, J.W. (2009). Optimisation of technologies for hydro-mechanical descaling of steel. Metallurgical Research & Technology. 106(2), 60-68. https://doi.org/10.1051/ metal/2009015.
[7] Zhang, D., Wang, H., Liu, J., Wang, C., Ge, J., Zhu, Y., Chen, X. & Hu, B. (2022). Flow characteristics of oblique submerged impinging jet at various impinging heights. Journal of Marine Science and Engineering. 10(3), 399. https://doi.org/10.3390/jmse10030399.
[8] Song, X., Lyu, Z., Li, G. & Hu, X. (2017). Numerical analysis of the impact flow field of multi-orifice nozzle hydrothermal jet combined with cooling water. International Journal of Heat and Mass Transfer. 114, 578-589. https://doi.org/10.1016/j.ijheatmasstransfer.2017.06.106.
[9] Gongye, F., Zhou, J., Peng, J., Zhang, H., Peng, S., Li, S. & Deng, H. (2023). Study on the removal of oxide scale formed on 300 M steel special-shaped hot forging surfaces during heating at elevated temperature by a high-pressure water descaling process. Materials. 16, 1745, 1-14. https://doi.org/10.3390/ma16041745.
[10] Wen, J., Qi, Z., Behbahani, S. S., Pei, X. & Iseley, T. (2019). Research on the structures and hydraulic performances of the typical direct jet nozzles for water jet technology. Journal of the Brazilian Society of Mechanical Sciences and Engineering. 41, 1-12. https://doi.org/10.1007/s40430-019-2075-2.
[11] Rouly, E., Warkentin, A. & Bauer, R. (2015). Design and testing of low-divergence elliptical-jet nozzles. Journal of Mechanical Science and Technology. 29, 1993-2003. https://doi.org/10.1007/s12206-015-0420-7.
[12] Huang, F., Mi, J., Li, D. & Wang, R. (2020). Impinging performance of high-pressure water jets emitting from different nozzle orifice shapes. Geofluids. 2020, 8831544. https://doi.org/10.1155/2020/8831544.
Go to article

Authors and Affiliations

Bowen Yang
1
Guangqiang Liu
2
Chengcheng Xu
3
Kun Liu
1
ORCID: ORCID
Peng Han
1

  1. School of Materials and Metallurgy, University of Science and Technology Liaoning, China
  2. School of Civil Engineering, University of Science and Technology Liaoning, China
  3. Cold Rolling Mill Plant, ANGANG Steel Company Limited, China
Download PDF Download RIS Download Bibtex

Abstract

Iron black commonly employs in thermal insulation riser sleeves due to its ability to react with aluminum powder, generating heat. However, the complex production process and unstable composition of iron black lead to high production costs. The potential of using arc furnace flue ash (AFFA) as a complete substitute for iron black and MnO2 and KNO3 oxidizing agents in conventional riser sleeves was investigated in this study. Waste material can be transformed into a valuable resource, while production costs can be reduced by utilizing arc furnace flue ash. The research examined the impact of varying types and amounts of arc furnace flue ash on riser sleeve temperature and holding time by conducting single-factor and orthogonal optimization experiments. The orthogonal optimization experiment determined that the optimum ratio of each oxidant was 6 % arc flue ash, 3 % MnO2 and 6 % KNO3. At this time, the highest temperature was 1512 ℃ and the holding time was 244 s. Results indicated that different types of arc furnace flue ash used as an oxidizing agent demonstrated superior holding capacity and heat generation performance compared to iron black. Additionally, a comparative analysis of factory casting experiments using ductile iron 600-3 (IS) revealed that both arc furnace flue ash and iron black risers effectively countered shrinkage. However, arc furnace flue ash risers exhibited improved mechanical properties, as evidenced by the hardness of the castings.
Go to article

Bibliography

[1] Lu, J.J., Qian, J.B., Yang, L. & Wang, H.F. (2023). Preparation and performance optimization of organosilicon slag exothermic insulating riser. Archives of Foundry Engineering. 23(1), 75-82. DOI: 10.24425/afe.2023.144283.
[2] Vasková, I., Conev, M. & Hrubovčáková, M. (2017). The influence of using different types of risers or chills on shrinkage production for different wall thickness for material EN-GJS-400-18LT. Archives of Foundry Engineering. 17(2), 131-136. DOI: 10.1515/afe-2017-0064.
[3] Sowa, L., Skrzypczak, T. & Kwiatoń, P. (2019). The influence of riser shape on feeding effectiveness of solidifying casting. Archives of Foundry Engineering. 19(4), 91-94. DOI: 10.24425/afe.2019.129636.
[4] Krajewski, P.K., Gradowski, A. & Krajewski, W.K. (2013). Heat exchange in the system mould - riser - ambient. part ii: surface heat emission from open riser to ambient. Archives of Metallurgy and Materials. 58(4), 1149-1153. DOI: 10.2478/amm-2013-0140.
[5] Xu, X. Hui,G,D. Ma, B, H . et al. (2017). Research on high efficiency heat insulation risers for casting. Casting technology. 38(03), 726-728. (in Chinese).
[6] Zhang, S.L., Wu, B., Qin, Z.G.,et al .(2010). Ignition temperature of 2Al/Fe2O3 aluminum thermite. Energy Containing Materials. 18(02), 162-166. (in Chinese).
[7] Duan, W. H., Li, G., Zu. C.S., et al (2017). Control of critical characteristics of heat-insulating riser sleeves and countermeasures for application problems. China Casting Equipment and Technology, 2017(06), 20-24. (in Chinese).
[8] Sambo, A. & Szymanek, A. (2014). Analysis of the distribution of chemical compounds from fly ash exposed to weather. Chemical and Process Engineering. 35(3), 265-275. DOI: 10.2478/cpe-2014-0020.
[9] Chen, J. (2022). Application of steelmaking electric arc furnace ash in sintered bricks[J]. Brick and Tile, 2020 (7): 25-27. DOI:10.16001/j.cnki.1001-6945.2020.07.011.
[10] Wang, J., Zhang, Y.Y., Cui, K.K., Fu. T., Gao, J.J. Shahid Hussain, Tahani Saad AlGarni. (2021). Pyrometallurgical recovery of zinc and valuable metals from electric arc furnace dust – A review. Journal of Cleaner Production. 298, 126788. DOI:10.1016/j.jclepro.2021.126788.
[11] Donald, J.R. & Pickles, C.A. (1996). Reduction of electric arc furnace dust with solid iron powder. Canadian Metallurgical Quarterly. 35(3), 255-267. DOI:10.1016/0008-4433(96)00009-2.
[12] Lin, X.L. Peng. Z.W., Yan. J.X., Li. Z., Z. Hwang, J.Y. Zhang, Y.B., Li, G.H., Jiang, T. (2017). Pyrometallurgical recycling of electric arc furnace dust. Journal of Cleaner Production. 149, 1079-1100. DOI:10.1016/j.jclepro.2017.02.128.
[13] Abhilash T. Nair, Aneesh Mathew, Archana A R, M Abdul Akbar.(2022). Use of hazardous electric arc furnace dust in the construction industry: A cleaner production approach. Journal of Cleaner Production. 377, 134282, 0959-6526. DOI:10.1016/j.jclepro.2022.134282
Go to article

Authors and Affiliations

Junjie Zhu
1
ORCID: ORCID
Jian Feng
2
ORCID: ORCID
Ling Liu
1
ORCID: ORCID
Huafang Wang
1
ORCID: ORCID
Jijun Lu
1
ORCID: ORCID

  1. School of Mechanical Engineering and Automation, Wuhan Textile University, China
  2. CRRC Corporation Limited, China
Download PDF Download RIS Download Bibtex

Abstract

This paper presents the results of a study on the use of infrared thermography to assess the quality of liquid metal, a basic semi-finished product used in foundry production. EN AC-46000 alloy with the designation AlSi9Cu3(Fe) was used for the study. The crystallization process of the alloy was investigated using the TDA method with a Crystaldigraph device and Optris PI thermal imaging camera. The research describes how to use a thermal imaging camera to assess the quality of aluminium alloys. These alloys, due to their propensity in the liquid state to oxidise and absorb hydrogen, a refining procedure in the melting process. The effects of alloy refining are evaluated during technological tests of hydrogen solubility, density and casting shrinkage. The results presented in this paper showed that there is a statistical correlation between the density of the metal and the temperature values from the thermogram of the sample, obtained during its solidification. The existing correlation makes it possible to develop a thermographic inspection algorithm that allows a fast and non-contact assessment of aluminium alloy quality.
Go to article

Bibliography

[1] Dispinar, D., & Campbell, J. (2004). Critical assessment of reduced pressure test. Part 1: Porosity phenomena. International Journal of Cast Metals Research, 17(5), 280-286. https://doi.org/10.1179/136404604225020696.
[2] Kowalczyk W., Dańko R., Górny M., Kawalec M. & Burbelko A. (2022) Influence of High-Pressure Die Casting Parameters on the Cooling Rate and the Structure of EN-AC 46000 Alloy. Materials, 15(16), 5702. https://doi.org/10.3390/ma15165702.
[3] Y B Zuo, B Jiang, Y J Zhang & Z Fan. (2013). Degassing LM25 aluminium alloy by novel degassing technology with intensive melt shearing. International Journal of Cast Metals Research. 26(1), 16-21. doi: 10.1179/1743133612Y.0000000019.
[4] Pietrowski, S. (2001). Al-Si Alloys. Lodz, Poland: Wydawnictwo Politechniki Łódzkiej. ISBN 83-7283-029-0
[5] Gumienny, G., Pisarek, B., Szymczak, T., Gawroński, J., Just, P., Władysiak, R., Rapiejko, C. & Pacyniak, T. (2022). Effect of degassing parameters on mechanical properties of EN AC-46000 gravity die casting. Materials. 15(23), 8323, 1-13. https://doi.org/10.3390/ma15238323.
[6] Pietrowski, S., Gumienny, G., Pisarek, B. & Władysiak, R. (2004). Production control of advanced casting alloys with TDA method. Archives of Mechanical Technology and Automation. 24(3), 131-143, ISSN (1233-9709).
[7] Rapiejko C., Pisarek B., Czekaj E. & Pacyniak T., (2014). Analysis of AM60 and AZ91 Alloy Crystallization in Ceramic Moulds by Thermal Derivative Analysis (TDA). Archives of Metallurgy and Materials. 59, doi: 10.2478/amm-2014-0246.
[8] Gumienny G., Kurowska B. & Just P. (2019). The effect of Manganese on the Crystallization Process, Microstructure and Selected Properties of Compacted Graphite Iron. Archives of Metallurgy and Materials. 64(4), 1269-1275. doi: 10.24425/amm.2019.130090.
[9] Pisarek B., Rapiejko C. & Pacyniak T. (2019). Effect of intensive Cooling of Alloy AC-AlSi7Mg with Alloy additions on Microstructure and Mechanical Properties. Archives of Metallurgy and Materials. 64 (2), 677-681. DOI: 10.2478/amm-2019.127598.
[10] Władysiak, R. & Kozuń, A. (2015). An Application for Infrared Camera in Analyzing of the Solidification Process of Al-Si Alloys. Archives of Foundry Engineering. 15(3), 81-84. DOI: 10.1515/afe-2015-0065.
[11] Holtzer, M., Bobrowski, A., Grabowska, B., Eichholz, S. & Hodor, K. (2010). Investigation of carriers of lustrous carbon at high temperatures by infrared spectroscopy (FTIR). Archives of Foundry Engineering. 10(4), 61-68.
[12] Sapieta, M., Dekys, V., Kao, M., Pastor, M., Sapietova, A. & Drvarova, B. (2023). Investigation of the mechanical properties of spur involute gearing by infrared thermography. Applied Sciences. 13(10), 5988. https://doi.org/10.3390/app13105988.
[13] Umar M. &·Paulraj S. (2021). Thermography analysis and porosity formation during laser beam welding of AA5083 H111 aluminum alloy. Journal of Thermal Analysis and Calorimetry 146, 1551–1559. https://doi.org/10.1007/s10973-020-10140-z.
[14] Lanc Z., Strbac B., Zeljkovic M., Zivkovic A. & Hadzistevic M. (2018). Emissivity of Aluminium Alloy Using Infrared Thermography Technique. Materials and Technology. 52(3). doi:10.17222/mit.2017.152.
[15] Badulescu C., Grediac M., Haddadi H., Mathias J.-D., Balandraud X. & Tran H.-S. (2011) Applying the Grid Method and Infrared Thermography to Investigate Plastic deformation in Aluminium Multicrystal. Mechanics of Materials, 43(1), 36-53. doi:10.1016/j.mechmat.2010.11.001.
Go to article

Authors and Affiliations

Ryszard Władysiak
1
ORCID: ORCID

  1. Lodz University of Technology, Department of Materials Engineering and Production Systems, Łódź, Poland
Download PDF Download RIS Download Bibtex

Abstract

Microwave Assisted Self-propagating High-temperature Synthesis (MASHS) was used to prepare open-porous MAX phase preforms in Ti-Al-C and Ti-Si-C systems, which were further used as reinforcements for Al-Si matrix composite materials. The pretreatment of substrates was investigated to obtain open-porous cellular structures. Squeeze casting infiltration was chosen to be implemented as a method of composites manufacturing. Process parameters were adjusted in order to avoid oxidation during infiltration and to ensure the proper filling. Obtained materials were reproducible, well saturated and dense, without significant residual porosity or undesired interactions between the constituents. Based on this and the previous work of the authors, the reinforcement effect was characterized and compared for both systems. For the Al-Si+Ti-Al-C composite, an approx. 4-fold increase in hardness and instrumental Young's modulus was observed in relation to the matrix material. Compared to the matrix, Al-Si+Ti-Si-C composite improved more than 5-fold in hardness and almost 6-fold in Young's modulus. Wear resistance (established for different loads: 0.1, 0.2 and 0.5 MPa) for Al-Si+Ti-Al-C was two times higher than for the sole matrix, while for Al-Si+Ti-Si-C the improvement was up to 32%. Both composite materials exhibited approximately two times lower thermal expansion coefficients than the matrix, resulting in enhanced dimensional stability.
Go to article

Bibliography

[1] Gonzalez-Julian, J. (2021). Processing of MAX phases: From synthesis to applications. Journal of the American Ceramic Society. 104, 659-690. https://doi.org/10.1111/jace.17544.
[2] Barsoum, M.W. (2013). MAX Phases: Properties of Machinable Ternary Carbides and Nitrides. Wiley-VCH.
[3] Arróyave, R., Talapatra, A., Duong, T., Son, W., Gao, H. & Radovic M. (2017). Does aluminum play well with others? Intrinsic Al-A alloying behavior in 211/312 MAX phases. Materials Research Letters. 5(3), 170-178. https://doi.org/10.1080/21663831.2016.1241319.
[4] Khoptiar, Y. & Gotman, I. (2002). Ti2AlC ternary carbide synthesized by thermal explosion, Materials Letters. 57(1), 72-76. https://doi.org/10.1016/S0167-577X(02)00701-2.
[5] Jeitschko, W. & Nowotny, H. (1967). Die kristallstruktur von Ti3SiC2-ein neuer komplexcarbid-typ. Monatshefte Für Chemie. 98, 329-337. https://doi.org/10.1007/BF00899949.
[6] El Saeed, M.A., Deorsola, F.A. & Rashad, R.M. (2013). Influence of SPS parameters on the density and mechanical properties of sintered Ti3SiC2 powders. International Journal of Refractory Metals and Hard Materials. 41, 48-53. https://doi.org/10.1016/j.ijrmhm.2013.01.016.
[7] Radhakrishnan, R., Williams, J.J. & Akinc M. (1999). Synthesis and high-temperature stability of Ti3SiC2. Journal of Alloys and Compounds. 285(1-2), 85-88. https://doi.org/10.1016/S0925-8388(99)00003-1.
[8] Wang, Y., Huang, Z., Hu, W., Cai, L., Lei, C., Yu, Q. & Jiao Y. (2021). Preparation and characteristics of Ti3AlC2-Al3Ti/Al composite materials synthesized from pure Al and Ti3AlC2 powders. Materials Characterization. 178, 111298. https://doi.org/10.1016/j.matchar.2021.111298.
[9] Wang, Z., Ma, Y., Sun, K., Zhang, Q., Zhou, C., Shao, P., Xiu, Z. & Wu, G. (2022). Enhanced ductility of Ti3AlC2 particles reinforced pure aluminum composites by interface control. Materials Science and Engineering: A. 832, 142393. https://doi.org/10.1016/j.msea.2021.142393.
[10] Zhai, W., Pu, B., Sun, L., Xu, L., Wang, Y., He, L., Dong, H., Gao, Y., Han, M. & Xue, Y. (2022). Influence of Ti3AlC2 content and load on the tribological behaviors of Ti3AlC2p/Al composites. Ceramics International. 48(2), 1745-1756. https://doi.org/10.1016/j.ceramint.2021.09.254.
[11] Anasori, B., Caspi, E.N. & Barsoum, M.W. (2014). Fabrication and mechanical properties of pressureless melt infiltrated magnesium alloy composites reinforced with TiC and Ti2AlC particles. Materials Science and Engineering: A. 618, 511-522. https://doi.org/10.1016/j.msea.2014.09.039.
[12] Anasori, B. & Barsoum, M.W. (2016). Energy damping in magnesium alloy composites reinforced with TiC or Ti2AlC particles. Materials Science and Engineering: A. 653, 53-62. https://doi.org/10.1016/j.msea.2015.11.070.
[13] Hu, L., Kothalkar, A., O’Neil, M., Karaman, I. & Radovic, M. (2014). Current-activated, pressure-assisted infiltration: A novel, versatile route for producing interpenetrating ceramic-metal composites. Materials Research Letters. 2, 124-130. https://doi.org/10.1080/21663831.2013.873498.
[14] Song, I.H., Kim, D.K., Hahn, Y.D. & Kim, H.D. (2004). Investigation of Ti3AlC2 in the in situ TiC-Al composite prepared by the exothermic reaction process in liquid aluminum. Materials Letters. 58(5), 593-597. https://doi.org/10.1016/S0167-577X(03)00576-7.
[15] Wang, W.J., Gauthier-Brunet, V., Bei, G.P., Laplanche, G., Bonneville, J., Joulain, A. & Dubois, S. (2011). Powder metallurgy processing and compressive properties of Ti3AlC2/Al composites. Materials Science and Engineering: A. 530, 168-173. https://doi.org/10.1016/j.msea.2011.09.068.
[16] Chen, Y.L., Yan, M., Sun, Y.M., Mei, B.C. & Zhu, J.Q. (2009). The phase transformation and microstructure of TiAl/Ti2AlC composites caused by hot pressing. Ceramics International. 35(5), 1807-1812. https://doi.org/10.1016/j.ceramint.2008.10.009.
[17] Fedotov. A.F., Amosov. A.P., Latukhin. E.I. & Novikov. V.A. (2016). Fabrication of aluminum–ceramic skeleton composites based on the Ti2AlC MAX phase by SHS compaction. Russian Journal of Non-Ferrous Metals. 57(5), 33-40. https://doi.org/10.3103/S1067821216010053.
[18] Dang, W., Ren, S., Zhou, J., Yu, Y., Li, Z. & Wang, L. (2016). Influence of Cu on the mechanical and tribological properties of Ti3SiC2. Ceramics International. 42(8), 9972-9980. https://doi.org/10.1016/j.ceramint.2016.03.099.
[19] Shi, X., Wang, M., Xu, Z., Zhai, W. & Zhang, Q. (2013). Tribological behavior of Ti3SiC2/(WC-10Co) composites prepared by spark plasma sintering. Materials & Design. 45, 365-376. https://doi.org/10.1016/j.matdes.2012.08.069.
[20] Dang, W., Ren, S., Zhou, J., Yu, Y. & Wang, L. (2016). The tribological properties of Ti3SiC2/Cu/Al/SiC composite at elevated temperatures. Tribology International. 104, 294-302. https://doi.org/10.1016/j.triboint.2016.09.008.
[21] Krinitcyn, M., Fu, Z., Harris, J., Kostikov, K., Pribytkov, G.A., Greil, P. & Travitzky, N. (2017). Laminated object manufacturing of in-situ synthesized MAX-phase composites. Ceramics International. 43(12), 9241-9245. https://doi.org/10.1016/j.ceramint.2017.04.079.
[22] Li, H., Peng, L.M., Gong, M., He, L.H., Zhao, J.H. & Zhang, Y.F. (2005). Processing and microstructure of Ti3SiC2 / M (M = Ni or Co) composites. Materials Letters. 59(21), 2647-2649. https://doi.org/10.1016/j.matlet.2005.04.010.
[23] Sun, Z., Zhou, M.C. & Li, S. (2002). Tribological behavior of Ti3SiC2 based materials. Journal of Materials Science & Technology. 18(2), 142-145.
[24] Hu, C., Zhou, Y., Bao, Y. & Wan, D. (2006). Tribological properties of polycrystalline Ti3SiC2 and Al2O3-reinforced Ti3SiC2 composites. Journal of the American Ceramic Society. 89(11), 3456-3461. https://doi.org/10.1111/j.1551-2916.2006.01253.x.
[25] Yang, J., Gu, W., Pan, L.M., Song, K., Chen, X. & Qiu, T. (2011). Friction and wear properties of in situ (TiB2+TiC)/Ti3SiC2 composites. Wear. 271(11-12), 2940-2946. https://doi.org/10.1016/j.wear.2011.06.017.
[26] Lis, J., Chlubny, L., Łopaciński, M., Stobierski, L. & Bućko, M.M. (2008). Ceramic nanolaminates-Processing and application. Journal of the European Ceramic Society. 28(5), 1009-1014. https://doi.org/10.1016/j.jeurceramsoc.2007.09.033.
[27] Naplocha, K. (2013). Composite materials strengthened with preforms produced in the process of high-temperature synthesis in a microwave field (in Polish: Materiały kompozytowe umacniane preformami wytworzonymi w procesie wysokotemperaturowej syntezy w polu mikrofalowym). Wroclaw: Oficyna Wydawnicza PWr.
[28] Merzhanov, G. (2011). Thermally coupled SHS reactions. International Journal of Self-Propagating High-Temperature Synthesis. 20, 61-63. https://doi.org/10.3103/ S1061386211010109.
[29] Dmitruk, A., Żak, A., Naplocha, K., Dudziński, W. & Morgiel, J. (2018). Development of pore-free Ti-Al-C MAX/Al-Si MMC composite materials manufactured by squeeze casting infiltration. Materials Characterization. 146, 182-188. https://doi.org/10.1016/j.matchar.2018.10.005.
[30] Dmitruk, A., Naplocha, K., Żak, A., Strojny-Nędza, A., Dieringa, H. & Kainer K.U. (2019). Development of pore-free Ti-Si-C MAX/Al-Si composite materials manufactured by squeeze casting infiltration. Journal of Materials Engineering and Performance. 28, 6248-6257. https://doi.org/10.1007/s11665-019-04390-8.
[31] Dmitruk, A., Naplocha, K. & Strojny-Nędza, A. (2018). Thermal properties of Al alloy matrix composites reinforced with MAX type phases. Composites Theory and Practice. 18(1), 32-36. [32] Dmitruk, A. & Naplocha, K. (2018). Manufacturing of Al alloy matrix composite materials reinforced with MAX phases. Archives of Foundry Engineering. 18(2), 198-202. DOI: 10.24425/122528.
[33] Chen X. & Bei G. (2017). Toughening mechanisms in nanolayered MAX phase ceramics-a review. Materials (Basel). 10(4), 1-12. https://doi.org/10.3390/ma10040366.
[34] Yang, J., Liao, C., Wang, J., Jiang, Y. & He, Y. (2014). Effects of the Al content on pore structures of porous Ti3 AlC2 ceramics by reactive synthesis. Ceramics International. 40(3), 4643-4648. https://doi.org/10.1016/ j.ceramint.2013.09.004.
[35] Hashimoto, S., Nishina, N., Hirao, K., Zhou, Y., Hyuga, H., Honda, S. & Iwamoto, Y. (2012). Formation mechanism of Ti2AlC under the self-progating high-temperature synthesis (SHS) mode. Materials Research Bulletin. 47(5), 1162-1168. https://doi.org/10.1016/j.materresbull.2012.02.003.
[36] Yang. J., Liao. C., Wang. J., Jiang. Y. & He. Y. (2014). Reactive synthesis for porous Ti3AlC2 ceramics through TiH2, Al and graphite powders. Ceramics International. 40(5), 6739-6745. https://doi.org/10.1016/ j.ceramint.2013.11.136.
[37] Hendaoui, A., Vrel, D., Amara, A., Langlois, P., Andasmas, M. & Guerioune, M. (2010). Synthesis of high-purity polycrystalline MAX phases in Ti-Al-C system through mechanically activated self-propagating high-temperature synthesis. Journal of the European Ceramic Society. 30(4), 1049-1057. https://doi.org/10.1016/j.jeurceramsoc.2009.10.001.
[38] Yeh, C.L. & Shen, Y.G. (2008). Effects of SiC addition on formation of Ti3SiC2 by self-propagating high-temperature synthesis. Journal of Alloys and Compounds. 461(1-2), 654-660. https://doi.org/10.1016/j.jallcom.2007.07.088.
[39] Zhang, Y., Ding, G.P., Zhou, Y.C. & Cai, B.C. (2002). Ti3SiC2 - a selflubricating ceramic, Materials Letters. 55(5), 285-289. https://doi.org/10.1016/S0167-577X(02)00379-8.
[40] Radovic, M. & Barsoum, M.W. (2013). MAX phases: Bridging the gap between metals and ceramics. American Ceramic Society Bulletin. 92(3), 20-27.
[41] Barsoum, M.W., El-raghy, T., Rawn, C.J., Porter, W.D., Wang, H., Payzant, E.A. & Hubbard, C.R. (1999). Thermal properties of Ti3SiC2. Journal of Physics and Chemistry of Solids. 60(4), 429-439. https://doi.org/10.1016/S0022-3697(98)00313-8.
[42] Son, W., Duong, T., Talapatra, A., Gao, H., Arróyave, R. & Radovic, M. (2016). Ab-initio investigation of the finite-temperatures structural, elastic, and thermodynamic properties of Ti3AlC2 and Ti3SiC2. Computational Materials Science. 124, 420-427. https://doi.org/10.1016/j.commatsci.2016.08.015.
[43] Shih, C., Meisner, R., Porter, W., Katoh, Y. & Zinkle, S.J. (2013). Physical and thermal mechanical characterization of non-irradiated MAX phase materials (Ti-Si-C and Ti-Al-C systems). Fusion Reactor Materials Program. 55, 78-93.
[44] Wang, X.H. & Zhou, Y.C. (2010). Layered Machinable and electrically conductive Ti2AlC and Ti3AlC2 ceramics: a review. Journal of Materials Science & Technology. 26(5), 385-416. https://doi.org/10.1016/S1005-0302(10)60064-3.

Go to article

Authors and Affiliations

A. Dmitruk
1
ORCID: ORCID
K. Naplocha
1
ORCID: ORCID
A. Żak
2
A. Strojny-Nędza
3

  1. Wrocław University of Science and Technology, Faculty of Mechanical Engineering, Department of Lightweight Elements Engineering, Foundry and Automation, Poland
  2. Wrocław University of Science and Technology, Faculty of Chemistry, Institute of Advanced Materials, Poland
  3. Łukasiewicz Institute of Microelectronics and Photonics, Poland
Download PDF Download RIS Download Bibtex

Abstract

Austenitic Fe-Ni-Cr alloys are commonly used for the production of castings intended for high-temperature applications. One area where Fe-Ni-Cr castings are widely used is the equipment for heat treatment furnaces. Despite the good heat resistance properties of the materials used for the castings, they tend to develop cracks and deformations over time due to cyclic temperature changes experienced under high temperature operating conditions. In the case of carburizing furnace equipment, thermal stresses induced by the temperature gradient in each operating cycle on rapidly cooled elements have a significant influence on the progressive fatigue changes. In the carburized subsurface zone, also the different thermal expansion of the matrix and non-metallic precipitates plays a significant role in stress distribution. This article presents the results of analyses of thermal stresses in the surface and subsurface layer of carburized alloy during cooling, taking into account the simultaneous effect of both mentioned stress sources. The basis for the stress analyzes were the temperature distribution in the cross-section of the cooled element as a function cooling time, determined numerically using FEM. These distributions were taken as the thermal load of the element. The study presents the results of analyses on the influence of carbide concentration increase on stress distribution changes caused by the temperature gradient. The simultaneous consideration of both thermal stress sources, i.e. temperature gradient and different thermal expansions of phases, allowed for obtaining qualitatively closer results than analyzing the stress sources independently
Go to article

Bibliography

[1] Lai, G.Y. (2007). High-Temperature Corrosion and Materials Applications. ASM International.
[2] Davis, J.R. (1997). Industrial applications of heat-resistant materials. In Heat Resistant Materials. 67-85.
[3] Piekarski, B. (2012). Creep-resistant castings used in heat treatment furnaces. Szczecin: West Pomeranian University of Technology Publishing House. (in Polish).
[4] Lo, K.H., Shek, C. H., & Lai, J. K. L. (2009). Recent developments in stainless steels. Materials Science and Engineering R: Reports. 65(4-6), 39-104.
[5] Carreon, M., Ramos Azpeitia, M. O., Hernandez Rivera, J. L., Bedolla Jacuinde, A., Garcia Lopez, C. J., Ruiz Ochoa, J. A., & Gonzalez Castillo, A. C. (2023). Development of a novel heat-resistant austenitic cast steel with an improved thermal fatigue resistance. International Journal of Metalcasting. 17(2), 1114-1127. DOI: 10.1007/s40962-022-00838-1.
[6] Drotlew, A., Garbiak, M. & Piekarski, B. (2012). Cast steels for creep-resistant parts used in heat-treatment plants. Archives of Foundry Engineering, 12(4), 31-38. DOI: 10.2478/v10266-012-0103-0.
[7] Lekakh, S. N., Buchely, M., Li, M., & Godlewski, L. (2023). Effect of Cr and Ni concentrations on resilience of cast Nb-alloyed heat resistant austenitic steels at extreme high temperatures. Materials Science and Engineering: A. 873, 145027. DOI: doi.org/10.1016/j.msea.2023.145027.
[8] Piekarski, B. & Drotlew A. (2019). Cast grates used in heat treatment furnaces. Archives of Foundry Engineering, 19(3), 49-54. DOI: 10.24425/afe.2019.127138.
[9] Nandwana, D., Bhupendra, N. K., Bhargava, T., Nandwana, K., & Jawale, G. (2010). Design, Finite Element analysis and optimization of HRC trays used in heat treatment process. Proceedings of the World Congress on Engineering WCE 2010, (II), (pp. 1149-1154).
[10] Ul-Hamid, A., Tawancy, H. M., Mohammed, A. R. I., & Abbas, N. M. (2006). Failure analysis of furnace tubes exposed to excessive temperature. Engineering Failure Analysis. 13(6), 1005-1021. DOI: 10.1016/j.engfailanal. 2005.04.003.
[11] Piekarski, B. (2010). Damage of heat-resistant castings in a carburizing furnace. Engineering Failure Analysis. 17(1), 143-149. DOI: 10.1016/j.engfailanal.2009.04.011.
[12] Reihani, A., Razavi, S. A., Abbasi, E., & Etemadi, A. R. (2013). Failure analysis of welded radiant tubes made of cast heat-resisting steel. Journal of failure Analysis and Prevention. 13(6), 658-665. DOI: 10.1007/s11668-013-9741-y.
[13] Bochnakowski, W., Szyller, Ł. & Osetek, M. (2019). Damage characterization of belt conveyor made of the 330Nb alloy after service in a carburizing atmosphere in a continuous heat treatment furnace. Engineering Failure Analysis. 103, 173-183. DOI: 10.1016/j.engfailanal.2019.04.058.
[14] González-Ciordia, B., Fernández, B., Artola, G., Muro, M., Sanz, Á., & López de Lacalle, L. N. (2019). Failure-analysis based redesign of furnace conveyor system components: a case study. Metals. 9(8), 816, 1-12. DOI: 10.3390/met9080816.
[15] Srikanth, S., Saravanan, P., Khalkho, B., & Banerjee, P. (2021). Failure analysis of inconel 601 radiant tubes in continuous annealing furnace of hot dip galvanizing line. Journal of Failure Analysis and Preven-tion, 21. 747-758. DOI: 10.1007/s11668-021-01148-0.
[16] Gutowski, P. (1989). Analysis of cracking causes in grates used in carburising furnaces. Szczecin: Diss., Politechnika Szczecińska. (in Polish).
[17] Schnaas, A., Grabke, H.J. (1978). High-Temperature Corrosion and Creep of Ni-Cr-Fe Alloys in Carburizing and Oxidizing Environments. Oxidation of Metals. 12(5), 387-404. https://doi.org/10.1007/BF00612086.
[18] Zatorski, Z. & Tuleja, J. (2017). Numerical modelling of micro-stresses in carbonised austenitic cast steel under rapid cooling conditions. Archives of Metallurgy and Materials. 62(2), 635-641. DOI: 10.1515/amm-2017-0093.
[19] Bajwoluk, A. & Gutowski, P. (2019). Stress and crack propagation in the surface layer of carburized stable austenitic alloys during cooling. Materials at High Temperatures. 36(1), 9-18. DOI: 10.1080/09603409.2018144 8528.
[20] Bajwoluk, A. & Gutowski, P. (2017). The effect of cooling agent on stress and deformation of charge-loaded cast pallets. Archives of Foundry Engineering. 17(4), 13-18. DOI: 10.1515/afe-2017-0123.
[21] Bajwoluk, A. & Gutowski, P. (2018). Design options to decrease the thermal stresses in cast accessories for heat and chemical treatment furnaces. Archives of Foundry Engineering. 18(4), 125-130. DOI:10.24425/afe.2018. 125181.
[22] Bajwoluk, A. & Gutowski, P. (2019). Thermal stresses in the accessories of heat treatment furnaces vs cooling kinetics. Archives of Foundry Engineering. 19(3), 88-93. DOI: 10.24425/afe.2019.127146.
[23] Bajwoluk, A. & Gutowski, P. (2021). Effect of thermal nodes reduction in wall connections of the charge-handling furnace grates on thermal stresses. Archives of Foundry Engineering. 21(3), 53-58. DOI: 10.24425/afe.2021.138665.
[24] Tuleja, J., Kędzierska, K. & Sowa, M. (2022). The use of the finite element method to locate the places of damage occurrence in elements of technological equipment in carburizing furnaces. Procedia Computer Science. 207, 3931-3937. DOI: 10.1016/j.procs.2022.09.455.
[25] Bajwoluk, A. & Gutowski, P. (2023). Analysis of thermal stresses synergy in surface layer of carburised creep-resistant casts during rapid cooling processes. Materials at High Temperatures. 40(1), 64-76. DOI: 10.1080/09603409.2022. 2162684.
[26] Zienkiewicz, O.C. (1971). Finite element method in engineering science. London: McGraw-Hill.
[27] Midas NFX 2017: Analysis Manual, 2017.
[28] Standard PN-EN 10295: 2004. Heat resistant steel castings.
[29] Church, B. C., Sanders, T. H., Speyer, R. F., & Cochran, J. K. (2007). Thermal expansion matching and oxidation resistance of Fe–Ni–Cr interconnect alloys. Material Science and Engineering A. 452-453. https://doi.org/10.1016/j.msea.2006.10.149.
[30] Guo, X., Liu, Z., Li, L., Cheng, J., Su, H., & Zhang, L. (2022). Revealing the long-term oxidation and carburization mechanism of 310S SS and Alloy 800H exposed to supercritical carbon dioxide. Materials Chararacterization. 183, 111603. DOI: 10.1016/j.matchar.2021.111603.
[31] Shaffer, P.T.B.(1964). Plenum Press Handbooks Of High-Temperature Materials, Springer Science + Business Media.
[32] Schutze, M. (1997). Protective oxide scales and their breakdown. Ed. by D. R. Holmes, Institute of Corrosion, John Wiley & Sons.
[33] Huntz, A.M. (1995). Stresses in NiO, Cr2O3, and A2O3, oxide, Mater Science and Engineering A. 201 (1-2), 211-228. https://doi.org/10.1007/BF02648633.
[34] Richard, C. S., Béranger, G., & Decomps, F. (1995). Study of Cr203 coatings Part I: Microstructures and modulus. Journal of Thermal Spray Technology. 4(4), 342-346. https://doi.org/10.1007/BF02648633.
[35] Pang, X., Gao, K., & Volinsky, A. A. (2007). Microstructure and mechanical properties of chromium oxide coatings. Journal of Materials Research. 22(12), 3531-3537.
[36] Ji, A. L., Wang, W., Song, G. H., Wang, Q. M., Sun, C., & Wen, L. S. (2004). Microstructures and mechanical properties of chromium oxide films by arc ion plating. Materials Letters. 58(14), 1993-1998. https://doi.org/10.1016/j.matlet. 2003.12.029.
[37] Barshilia, H.C. & Rajam, K.S. (2008). Growth and characterization of chromium oxide coatings prepared by pulsed-direct current reactive unbalanced magnetron sputtering. Applied Surface Science. 255(9), 2925-2931. https://doi.org/10.1016/j.apsusc.2008.08.057.
[38] Gaillac, R., Pullumbi, P., & Coudert, F. X. (2016). ELATE: an open-source online application for analysis and visualization of elastic tensors. Journal of Physics: Condensed Matter. 28(27), 275201.
Go to article

Authors and Affiliations

A. Bajwoluk
1
ORCID: ORCID
P. Gutowski
1
ORCID: ORCID

  1. Mechanical Engineering Faculty, West Pomeranian University of Technology, Szczecin Al. Piastów 19, 70-310 Szczecin, Poland
Download PDF Download RIS Download Bibtex

Abstract

In view of the increasing scarcity of bauxite resources in China, the high energy consumption and high pollution of electrolytic aluminum, and the requirements for energy conservation and environmental protection, aluminum recycling and high-value utilization of its derivatives have evolved into a crucial development requirement for the aluminum industry in the future. As an important part of the development of recycled aluminum resources, the high-value application of scrap aluminum cans has always been a hot research topic in various recycled aluminum processing enterprises and scientific research units. The traditional regeneration system of waste cans includes a series of complex technological processes such as pretreatment, paint removal, smelting system and casting system, which is difficult to control in the middle of the process. Most of the recycled scrap aluminum cans are cast and downgraded for later use, except for a part of them used as alloy materials for new cans. In this paper, combined with the research on the preparation of metal aluminum alkoxide, combined with recrystallization heat conduction to further study the effective dissolution or adsorption how to remove impurity elements to obtain high-purity aluminum alcohol salt mechanism research, and thermal effect of alcohols with different carbon chains on the synthesis of high-purity aluminum alkoxide was further investigated. Moreover, the changes in morphology and pore size distribution of hydrolyzed alumina precursor materials under different hydrothermal temperature conditions were discussed by means of the alkoxide hydrolysis-sol-gel process. Eventually, the aluminum alkoxide was obtained by the reaction of waste cans with isopropanol and heavy crystal thermal conductivity, and the high-purity aluminum alkoxide was purified by vacuum distillation. Under the hydrothermal condition of 160°C, the high-purity alumina material with a purity of 99.99% and an original crystal size of 200nm was prepared.
Go to article

Bibliography

[1] Duan, R. (2016). Research on key technology of regenerating 3104 aluminum alloy for cans. TaiYuan: North University of China.
[2] Yang, L. (2020). Discussion on recycling of aluminum beverage cans without degrading can stock. Light Alloy Fabrication Technology. 48(2), 8-11.
[3] Liu, J. (2010). Formation and separation of iron-containing organic compounds in aluminum isopropyl alcohol and application of high purity aluminum alcohol salts. DaLIian: Dalian University of Technology.
[4] Cheng, X. (2012). Theoretical investigations on the hydrolysis-oligomerization mechanisms of silicon and aluminum alkoxides. Jinan:Shandong University.
[5] Yoo, S., Yoon, H. & Jang, H. (2007). Synthesis of aluminum ethoxide from used aluminum cans. Korean Journal of Chemical Engineering. 24, 872-876. https://doi.org/10.1007/s11814-007-0057-z.
[6] Yoo, S., Yoon, H. & Jang, H, (2007). Dissolution kinetics of aluminum can in isopropyl alcohol for aluminum isopropoxide. Chemical Engineering Journal. 133(1-3), 79-84. https://doi.org/10.1016/j.cej.2007.02.003.
[7] Zhang, G., Liu, B., Pan, D., Tian, J., Liu, Y., Zhao, R. The invention relates to a green recycling method of waste aluminum cans: CHINA, CN201210432365.2[P]. 22012.11.02.
[8] Li, X. (2021). Multiscale modeling and simulation of particle, batch kettle and fixed bed adsorption kinetics. Beijing: Beijing University of Chemical Technology.
[9] Ning J. Chen D., Liu Y. (2021). Efficient adsorption removal and adsorption mechanism of basic fuchsin by recyclable Fe3O4@CD magnetic microspheres. Journal of Central South University. 28(12), 3666-3680. https://doi.org/10.1007/s11771-021-4845-0.
[10] Rabah, M.A. (2023). Preparation of aluminium-magnesium alloys and some valuable salts from used beverage cans. Waste Management. 23(2), 173-182. https://doi.org/10.1016/S0956-053X(02)00152-6.
[11] Hong, Z., Yoshitaka, N.,& Isamu, Y. (2004). Analysis of the recycling system for aluminum cans, focusing on collection transportation and the intermediate processing methods. Journal of Material Cycles and Waste Management. 6, 153-161. https://doi.org/10.1007/s10163-003-0114-6.
[12] Zhu, W. (2013). Preparation of McM-41 mesoporous molecular sieves and their adsorption of heavy metal ions, Kunming: Kunming University of Science and Technology.
[13] Liu, B., Yang, J., Xue, T. & Sun, K. (2020). Adsorption kinetics and thermodynamics of P(V) by Tio2-Fe3O4-ATP adsorbent. Material Protection. 53(8), 68-73.
[14] Cao, F., Sun, D., Qiu, X., Zhou, D., Zhang, X., & Sun, C. (2022). Design and synthesis of novel thionocarbamate for copper-sulfur flotation separation and research on its adsorption mechanism. Transactions of Nonferrous Metals Society of China.
[15] Tan, S., Yang, J., & Li, C. (2020). Discussion on the practical application of activated carbon adsorption method to treat organic waste gas. Guangdong Chemical Engineering. 47(18), 141-142.
Go to article

Authors and Affiliations

Chengmin Wang
1
Anatoly Politov
2
Xiuhui Wang
1
Jinlong Yang
3

  1. Dalian Jiaotong University, China
  2. Institute of Solid State Chemistry and Mechanochemistry, Russia
  3. State Key Laboratory of New Ceramics & Fine Processing, China

Instructions for authors

Submission


To submit the article, please use the Editorial System provided here:

https://www.editorialsystem.com/afe


Papers submitted in any other way will not be accepted.



The Journal does not have submission charges.


The APC Article Processing Charge is 110 euros (500zł for Polish authors). In some cases, the APC is paid as a part of the scientific conference fee, for which the AFE journal is a supportive one. If not, it is payable after the acceptance of the final article by direct money transfer.


Bank account details:


Account holder: Stowarzyszenie Wychowankow Politechniki Slaskiej Kolo Odlewnikow
Account holder address: ul. Towarowa 7, 44-100 Gliwice, Poland
Account numbers: BIC BPKOPLPW IBAN PL17 1020 2401 0000 0202 0183 3748


Instructions for the preparation of an Archives of Foundry Engineering Paper

Publication Ethics Policy


Publication Ethics Policy

The standards of expected ethical behavior for all parties involved in publishing in the Archives of Foundry Engineering journal: the author, the journal editor and editorial board, the peer reviewers and the publisher are listed below.

All the articles submitted for publication in Archives of Foundry Engineering are peer reviewed for authenticity, ethical issues and usefulness as per Review Procedure document.

Duties of Editors
1. Monitoring the ethical standards: Editorial Board monitors the ethical standards of the submitted manuscripts and takes all possible measures against any publication malpractices.
2. Fair play: Submitted manuscripts are evaluated for their scientific content without regard to race, gender, sexual orientation, religious beliefs, citizenship, political ideology or any other issues that is a personal or human right.
3. Publication decisions: The Editor in Chief is responsible for deciding which of the submitted articles should or should not be published. The decision to accept or reject the article is based on its importance, originality, clarity, and its relevance to the scope of the journal and is made after the review process.
4. Confidentiality: The Editor in Chief and the members of the Editorial Board t ensure that all materials submitted to the journal remain confidential during the review process. They must not disclose any information about a submitted manuscript to anyone other than the parties involved in the publishing process i.e., authors, reviewers, potential reviewers, other editorial advisers, and the publisher.
5. Disclosure and conflict of interest: Unpublished materials disclosed in the submitted manuscript must not be used by the Editor and the Editorial Board in their own research without written consent of authors. Editors always precludes business needs from compromising intellectual and ethical standards.
6. Maintain the integrity of the academic record: The editors will guard the integrity of the published academic record by issuing corrections and retractions when needed and pursuing suspected or alleged research and publication misconduct. Plagiarism and fraudulent data is not acceptable. Editorial Board always be willing to publish corrections, clarifications, retractions and apologies when needed.

Retractions of the articles: the Editor in Chief will consider retracting a publication if:
- there are clear evidences that the findings are unreliable, either as a result of misconduct (e.g. data fabrication) or honest error (e.g. miscalculation or experimental error)
- the findings have previously been published elsewhere without proper cross-referencing, permission or justification (cases of redundant publication)
- it constitutes plagiarism or reports unethical research.
Notice of the retraction will be linked to the retracted article (by including the title and authors in the retraction heading), clearly identifies the retracted article and state who is retracting the article. Retraction notices should always mention the reason(s) for retraction to distinguish honest error from misconduct.
Retracted articles will not be removed from printed copies of the journal nor from electronic archives but their retracted status will be indicated as clearly as possible.

Duties of Authors
1. Reporting standards: Authors of original research should present an accurate account of the work performed as well as an objective discussion of its significance. Underlying data should be represented accurately in the paper. The paper should contain sufficient details and references to permit others to replicate the work. The fabrication of results and making of fraudulent or inaccurate statements constitute unethical behavior and will cause rejection or retraction of a manuscript or a published article.
2. Originality and plagiarism: Authors should ensure that they have written entirely original works, and if the authors have used the work and/or words of others they need to be cited or quoted. Plagiarism and fraudulent data is not acceptable.
3. Data access retention: Authors may be asked to provide the raw data for editorial review, should be prepared to provide public access to such data, and should be prepared to retain such data for a reasonable time after publication of their paper.
4. Multiple or concurrent publication: Authors should not in general publish a manuscript describing essentially the same research in more than one journal. Submitting the same manuscript to more than one journal concurrently constitutes unethical publishing behavior and is unacceptable.
5. Authorship of the manuscript: Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the report study. All those who have made contributions should be listed as co-authors. The corresponding author should ensure that all appropriate co-authors and no inappropriate co-authors are included in the paper, and that all co-authors have seen and approved the final version of the paper and have agreed to its submission for publication.
6. Acknowledgement of sources: The proper acknowledgment of the work of others must always be given. The authors should cite publications that have been influential in determining the scope of the reported work.
7. Fundamental errors in published works: When the author discovers a significant error or inaccuracy in his/her own published work, it is the author’s obligation to promptly notify the journal editor or publisher and cooperate with the editor to retract or correct the paper.

Duties of Reviewers
1. Contribution to editorial decisions: Peer reviews assist the editor in making editorial decisions and may also help authors to improve their manuscript.
2. Promptness: Any selected reviewer who feels unqualified to review the research reported in a manuscript or knows that its timely review will be impossible should notify the editor and excuse himself/herself from the review process.
3. Confidentiality: All manuscript received for review must be treated as confidential documents. They must not be shown to or discussed with others except those authorized by the editor.
4. Standards of objectivity: Reviews should be conducted objectively. Personal criticism of the author is inappropriate. Reviewers should express their views clearly with appropriate supporting arguments.
5. Acknowledgement of sources: Reviewers should identify the relevant published work that has not been cited by authors. Any substantial similarity or overlap between the manuscript under consideration and any other published paper should be reported to the editor.
6. Disclosure and conflict of Interest: Privileged information or ideas obtained through peer review must be kept confidential and not used for personal advantage. Reviewers should not consider evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relations with any of the authors, companies, or institutions involved in writing a paper.

Peer-review Procedure


Review Procedure


The Review Procedure for articles submitted to the Archives of Foundry Engineering agrees with the recommendations of the Ministry of Science and Higher Education published in a booklet: ‘Dobre praktyki w procedurach recenzyjnych w nauce’ (MNiSW, Dobre praktyki w procedurach recenzyjnych w nauce, Warszawa 2011).

Papers submitted to the Editorial System are primarily screened by editors with respect to scope, formal issues and used template. Texts with obvious errors (formatting other than requested, missing references, evidently low scientific quality) will be rejected at this stage or will be sent for the adjustments.

Once verified each article is checked by the anti-plagiarism system Cross Check powered by iThenticate®. After the positive response, the article is moved into: Initially verified manuscripts. When the similarity level is too high, the article will be rejected. There is no strict rule (i.e., percentage of the similarity), and it is always subject to the Editor’s decision.
Initially verified manuscripts are then sent to at least four independent referees outside the author’s institution and at least two of them outside of Poland, who:

have no conflict of interests with the author,
are not in professional relationships with the author,
are competent in a given discipline and have at least a doctorate degree and respective
scientific achievements,
have a good reputation as reviewers.


The review form is available online at the Journal’s Editorial System and contains the following sections:

1. Article number and title in the Editorial System

2. The statement of the Reviewer (to choose the right options):

I declare that I have not guessed the identity of the Author. I declare that I have guessed the identity of the Author, but there is no conflict of interest

3. Detailed evaluation of the manuscript against other researches published to this point:

Do you think that the paper title corresponds with its contents?
Yes No
Do you think that the abstract expresses the paper contents well?
Yes No
Are the results or methods presented in the paper novel?
Yes No
Do the author(s) state clearly what they have achieved?
Yes No
Do you find the terminology employed proper?
Yes No
Do you find the bibliography representative and up-to-date?
Yes No
Do you find all necessary illustrations and tables?
Yes No
Do you think that the paper will be of interest to the journal readers?
Yes No

4. Reviewer conclusion

Accept without changes
Accept after changes suggested by reviewer.
Rate manuscript once again after major changes and another review
Reject


5. Information for Editors (not visible for authors).

6. Information for Authors


Reviewing is carried out in the double blind process (authors and reviewers do not know each other’s names).

The appointed reviewers obtain summary of the text and it is his/her decision upon accepting/rejecting the paper for review within a given time period 21 days.

The reviewers are obliged to keep opinions about the paper confidential and to not use knowledge about it before publication.

The reviewers send their review to the Archives of Foundry Engineering by Editorial System. The review is archived in the system.

Editors do not accept reviews, which do not conform to merit and formal rules of scientific reviewing like short positive or negative remarks not supported by a close scrutiny or definitely critical reviews with positive final conclusion. The reviewer’s remarks are sent to the author. He/she has to consider all remarks and revise the text accordingly.

The author of the text has the right to comment on the conclusions in case he/she does not agree with them. He/she can request the article withdrawal at any step of the article processing.

The Editor-in-Chief (supported by members of the Editorial Board) decides on publication based on remarks and conclusions presented by the reviewers, author’s comments and the final version of the manuscript.

The final Editor’s decision can be as follows:
Accept without changes
Reject


The rules for acceptance or rejection of the paper and the review form are available on the Web page of the AFE publisher.

Once a year Editorial Office publishes present list of cooperating reviewers.
Reviewing is free of charge.
All articles, including those rejected and withdrawn, are archived in the Editorial System.

Reviewers

List of Reviewers 2022

Shailee Acharya - S. V. I. T Vasad, India
Vivek Ayar - Birla Vishvakarma Mahavidyalaya Vallabh Vidyanagar, India
Mohammad Azadi - Semnan University, Iran
Azwinur Azwinur - Politeknik Negeri Lhokseumawe, Indonesia
Czesław Baron - Silesian University of Technology, Gliwice, Poland
Dariusz Bartocha - Silesian University of Technology, Gliwice, Poland
Iwona Bednarczyk - Silesian University of Technology, Gliwice, Poland
Artur Bobrowski - AGH University of Science and Technology, Kraków
Poland Łukasz Bohdal - Koszalin University of Technology, Koszalin Poland
Danka Bolibruchova - University of Zilina, Slovak Republic
Joanna Borowiecka-Jamrozek- The Kielce University of Technology, Poland
Debashish Bose - Metso Outotec India Private Limited, Vadodara, India
Andriy Burbelko - AGH University of Science and Technology, Kraków
Poland Ganesh Chate - KLS Gogte Institute of Technology, India
Murat Çolak - Bayburt University, Turkey
Adam Cwudziński - Politechnika Częstochowska, Częstochowa, Poland
Derya Dispinar- Istanbul Technical University, Turkey
Rafał Dojka - ODLEWNIA RAFAMET Sp. z o. o., Kuźnia Raciborska, Poland
Anna Dolata - Silesian University of Technology, Gliwice, Poland
Tomasz Dyl - Gdynia Maritime University, Gdynia, Poland
Maciej Dyzia - Silesian University of Technology, Gliwice, Poland
Eray Erzi - Istanbul University, Turkey
Flora Faleschini - University of Padova, Italy
Imre Felde - Obuda University, Hungary
Róbert Findorák - Technical University of Košice, Slovak Republic
Aldona Garbacz-Klempka - AGH University of Science and Technology, Kraków, Poland
Katarzyna Gawdzińska - Maritime University of Szczecin, Poland
Marek Góral - Rzeszow University of Technology, Poland
Barbara Grzegorczyk - Silesian University of Technology, Gliwice, Poland
Grzegorz Gumienny - Technical University of Lodz, Poland
Ozen Gursoy - University of Padova, Italy
Gábor Gyarmati - University of Miskolc, Hungary
Jakub Hajkowski - Poznan University of Technology, Poland
Marek Hawryluk - Wroclaw University of Science and Technology, Poland
Aleš Herman - Czech Technical University in Prague, Czech Republic
Mariusz Holtzer - AGH University of Science and Technology, Kraków, Poland
Małgorzata Hosadyna-Kondracka - Łukasiewicz Research Network - Krakow Institute of Technology, Poland
Dario Iljkić - University of Rijeka, Croatia
Magdalena Jabłońska - Silesian University of Technology, Gliwice, Poland
Nalepa Jakub - Silesian University of Technology, Gliwice, Poland
Jarosław Jakubski - AGH University of Science and Technology, Kraków, Poland
Aneta Jakubus - Akademia im. Jakuba z Paradyża w Gorzowie Wielkopolskim, Poland
Łukasz Jamrozowicz - AGH University of Science and Technology, Kraków, Poland
Krzysztof Janerka - Silesian University of Technology, Gliwice, Poland
Karolina Kaczmarska - AGH University of Science and Technology, Kraków, Poland
Jadwiga Kamińska - Łukasiewicz Research Network – Krakow Institute of Technology, Poland
Justyna Kasinska - Kielce University Technology, Poland
Magdalena Kawalec - AGH University of Science and Technology, Kraków, Poland
Gholamreza Khalaj - Islamic Azad University, Saveh Branch, Iran
Angelika Kmita - AGH University of Science and Technology, Kraków, Poland
Marcin Kondracki - Silesian University of Technology, Gliwice Poland
Vitaliy Korendiy - Lviv Polytechnic National University, Lviv, Ukraine
Aleksandra Kozłowska - Silesian University of Technology, Gliwice, Poland
Ivana Kroupová - VSB - Technical University of Ostrava, Czech Republic
Malgorzata Lagiewka - Politechnika Czestochowska, Częstochowa, Poland
Janusz Lelito - AGH University of Science and Technology, Kraków, Poland
Jingkun Li - University of Science and Technology Beijing, China
Petr Lichy - Technical University Ostrava, Czech Republic
Y.C. Lin - Central South University, China
Mariusz Łucarz - AGH University of Science and Technology, Kraków, Poland
Ewa Majchrzak - Silesian University of Technology, Gliwice, Poland
Barnali Maji - NIT-Durgapur: National Institute of Technology, Durgapur, India
Pawel Malinowski - AGH University of Science and Technology, Kraków, Poland
Marek Matejka - University of Zilina, Slovak Republic
Bohdan Mochnacki - Technical University of Occupational Safety Management, Katowice, Poland
Grzegorz Moskal - Silesian University of Technology, Poland
Kostiantyn Mykhalenkov - National Academy of Science of Ukraine, Ukraine
Dawid Myszka - Silesian University of Technology, Gliwice, Poland
Maciej Nadolski - Czestochowa University of Technology, Poland
Krzysztof Naplocha - Wrocław University of Science and Technology, Poland
Daniel Nowak - Wrocław University of Science and Technology, Poland
Tomáš Obzina - VSB - Technical University of Ostrava, Czech Republic
Peiman Omranian Mohammadi - Shahid Bahonar University of Kerman, Iran
Zenon Opiekun - Politechnika Rzeszowska, Rzeszów, Poland
Onur Özbek - Duzce University, Turkey
Richard Pastirčák - University of Žilina, Slovak Republic
Miroslawa Pawlyta - Silesian University of Technology, Gliwice, Poland
Jacek Pezda - ATH Bielsko-Biała, Poland
Bogdan Piekarski - Zachodniopomorski Uniwersytet Technologiczny, Szczecin, Poland
Jacek Pieprzyca - Silesian University of Technology, Gliwice, Poland
Bogusław Pisarek - Politechnika Łódzka, Poland
Marcela Pokusová - Slovak Technical University in Bratislava, Slovak Republic
Hartmut Polzin - TU Bergakademie Freiberg, Germany
Cezary Rapiejko - Lodz University of Technology, Poland
Arron Rimmer - ADI Treatments, Doranda Way, West Bromwich, West Midlands, United Kingdom
Jaromír Roučka - Brno University of Technology, Czech Republic
Charnnarong Saikaew - Khon Kaen University Thailand Amit Sata - MEFGI, Faculty of Engineering, India
Mariola Saternus - Silesian University of Technology, Gliwice, Poland
Vasudev Shinde - DKTE' s Textile and Engineering India Robert Sika - Politechnika Poznańska, Poznań, Poland
Bozo Smoljan - University North Croatia, Croatia
Leszek Sowa - Politechnika Częstochowska, Częstochowa, Poland
Sławomir Spadło - Kielce University of Technology, Poland
Mateusz Stachowicz - Wroclaw University of Technology, Poland
Marcin Stawarz - Silesian University of Technology, Gliwice, Poland
Grzegorz Stradomski - Czestochowa University of Technology, Poland
Roland Suba - Schaeffler Skalica, spol. s r.o., Slovak Republic
Maciej Sułowski - AGH University of Science and Technology, Kraków, Poland
Jan Szajnar - Silesian University of Technology, Gliwice, Poland
Michal Szucki - TU Bergakademie Freiberg, Germany
Tomasz Szymczak - Lodz University of Technology, Poland
Damian Słota - Silesian University of Technology, Gliwice, Poland
Grzegorz Tęcza - AGH University of Science and Technology, Kraków, Poland
Marek Tkocz - Silesian University of Technology, Gliwice, Poland
Andrzej Trytek - Rzeszow University of Technology, Poland
Mirosław Tupaj - Rzeszow University of Technology, Poland
Robert B Tuttle - Western Michigan University United States Seyed Ebrahim Vahdat - Ayatollah Amoli Branch, Islamic Azad University, Amol, Iran
Iveta Vaskova - Technical University of Kosice, Slovak Republic
Dorota Wilk-Kołodziejczyk - AGH University of Science and Technology, Kraków, Poland
Ryszard Władysiak - Lodz University of Technology, Poland
Çağlar Yüksel - Atatürk University, Turkey
Renata Zapała - AGH University of Science and Technology, Kraków, Poland
Jerzy Zych - AGH University of Science and Technology, Kraków, Poland
Andrzej Zyska - Czestochowa University of Technology, Poland



List of Reviewers 2021

Czesław Baron - Silesian University of Technology, Gliwice, Poland
Imam Basori - State University of Jakarta, Indonesia
Leszek Blacha - Silesian University of Technology, Gliwice
Poland Artur Bobrowski - AGH University of Science and Technology, Kraków, Poland
Danka Bolibruchova - University of Zilina, Slovak Republic
Pedro Brito - Pontifical Catholic University of Minas Gerais, Brazil
Marek Bruna - University of Zilina, Slovak Republic
Marcin Brzeziński - AGH University of Science and Technology, Kraków, Poland
Andriy Burbelko - AGH University of Science and Technology, Kraków, Poland
Alexandros Charitos - TU Bergakademie Freiberg, Germany
Ganesh Chate - KLS Gogte Institute of Technology, India
L.Q. Chen - Northeastern University, China
Zhipei Chen - University of Technology, Netherlands
Józef Dańko - AGH University of Science and Technology, Kraków, Poland
Brij Dhindaw - Indian Institute of Technology Bhubaneswar, India
Derya Dispinar - Istanbul Technical University, Turkey
Rafał Dojka - ODLEWNIA RAFAMET Sp. z o. o., Kuźnia Raciborska, Poland
Anna Dolata - Silesian University of Technology, Gliwice, Poland
Agnieszka Dulska - Silesian University of Technology, Gliwice, Poland
Maciej Dyzia - Silesian University of Technology, Poland
Eray Erzi - Istanbul University, Turkey
Przemysław Fima - Institute of Metallurgy and Materials Science PAN, Kraków, Poland
Aldona Garbacz-Klempka - AGH University of Science and Technology, Kraków, Poland
Dipak Ghosh - Forace Polymers P Ltd., India
Beata Grabowska - AGH University of Science and Technology, Kraków, Poland
Adam Grajcar - Silesian University of Technology, Gliwice, Poland
Grzegorz Gumienny - Technical University of Lodz, Poland
Gábor Gyarmati - Foundry Institute, University of Miskolc, Hungary
Krzysztof Herbuś - Silesian University of Technology, Gliwice, Poland
Aleš Herman - Czech Technical University in Prague, Czech Republic
Mariusz Holtzer - AGH University of Science and Technology, Kraków, Poland
Małgorzata Hosadyna-Kondracka - Łukasiewicz Research Network - Krakow Institute of Technology, Kraków, Poland
Jarosław Jakubski - AGH University of Science and Technology, Kraków, Poland
Krzysztof Janerka - Silesian University of Technology, Gliwice, Poland
Robert Jasionowski - Maritime University of Szczecin, Poland
Agata Jażdżewska - Gdansk University of Technology, Poland
Jan Jezierski - Silesian University of Technology, Gliwice, Poland
Karolina Kaczmarska - AGH University of Science and Technology, Kraków, Poland
Jadwiga Kamińska - Centre of Casting Technology, Łukasiewicz Research Network – Krakow Institute of Technology, Poland
Adrian Kampa - Silesian University of Technology, Gliwice, Poland
Wojciech Kapturkiewicz- AGH University of Science and Technology, Kraków, Poland
Tatiana Karkoszka - Silesian University of Technology, Gliwice, Poland
Gholamreza Khalaj - Islamic Azad University, Saveh Branch, Iran
Himanshu Khandelwal - National Institute of Foundry & Forging Technology, Hatia, Ranchi, India
Angelika Kmita - AGH University of Science and Technology, Kraków, Poland
Grzegorz Kokot - Silesian University of Technology, Gliwice, Poland
Ladislav Kolařík - CTU in Prague, Czech Republic
Marcin Kondracki - Silesian University of Technology, Gliwice, Poland
Dariusz Kopyciński - AGH University of Science and Technology, Kraków, Poland
Janusz Kozana - AGH University of Science and Technology, Kraków, Poland
Tomasz Kozieł - AGH University of Science and Technology, Kraków, Poland
Aleksandra Kozłowska - Silesian University of Technology, Gliwice Poland
Halina Krawiec - AGH University of Science and Technology, Kraków, Poland
Ivana Kroupová - VSB - Technical University of Ostrava, Czech Republic
Wacław Kuś - Silesian University of Technology, Gliwice, Poland
Jacques Lacaze - University of Toulouse, France
Avinash Lakshmikanthan - Nitte Meenakshi Institute of Technology, India
Jaime Lazaro-Nebreda - Brunel Centre for Advanced Solidification Technology, Brunel University London, United Kingdom
Janusz Lelito - AGH University of Science and Technology, Kraków, Poland
Tomasz Lipiński - University of Warmia and Mazury in Olsztyn, Poland
Mariusz Łucarz - AGH University of Science and Technology, Kraków, Poland
Maria Maj - AGH University of Science and Technology, Kraków, Poland
Jerzy Mendakiewicz - Silesian University of Technology, Gliwice, Poland
Hanna Myalska-Głowacka - Silesian University of Technology, Gliwice, Poland
Kostiantyn Mykhalenkov - Physics-Technological Institute of Metals and Alloys, National Academy of Science of Ukraine, Ukraine
Dawid Myszka - Politechnika Warszawska, Warszawa, Poland
Maciej Nadolski - Czestochowa University of Technology, Poland
Daniel Nowak - Wrocław University of Science and Technology, Poland
Mitsuhiro Okayasu - Okayama University, Japan
Agung Pambudi - Sebelas Maret University in Indonesia, Indonesia
Richard Pastirčák - University of Žilina, Slovak Republic
Bogdan Piekarski - Zachodniopomorski Uniwersytet Technologiczny, Szczecin, Poland
Bogusław Pisarek - Politechnika Łódzka, Poland
Seyda Polat - Kocaeli University, Turkey
Hartmut Polzin - TU Bergakademie Freiberg, Germany
Alena Pribulova - Technical University of Košice, Slovak Republic
Cezary Rapiejko - Lodz University of Technology, Poland
Arron Rimmer - ADI Treatments, Doranda Way, West Bromwich West Midlands, United Kingdom
Iulian Riposan - Politehnica University of Bucharest, Romania
Ferdynand Romankiewicz - Uniwersytet Zielonogórski, Zielona Góra, Poland
Mario Rosso - Politecnico di Torino, Italy
Jaromír Roučka - Brno University of Technology, Czech Republic
Charnnarong Saikaew - Khon Kaen University, Thailand
Mariola Saternus - Silesian University of Technology, Gliwice, Poland
Karthik Shankar - Amrita Vishwa Vidyapeetham , Amritapuri, India
Vasudev Shinde - Shivaji University, Kolhapur, Rajwada, Ichalkaranji, India
Robert Sika - Politechnika Poznańska, Poznań, Poland
Jerzy Sobczak - AGH University of Science and Technology, Kraków, Poland
Sebastian Sobula - AGH University of Science and Technology, Kraków, Poland
Marek Soiński - Akademia im. Jakuba z Paradyża w Gorzowie Wielkopolskim, Poland
Mateusz Stachowicz - Wroclaw University of Technology, Poland
Marcin Stawarz - Silesian University of Technology, Gliwice, Poland
Andrzej Studnicki - Silesian University of Technology, Gliwice, Poland
Mayur Sutaria - Charotar University of Science and Technology, CHARUSAT, Gujarat, India
Maciej Sułowski - AGH University of Science and Technology, Kraków, Poland
Sutiyoko Sutiyoko - Manufacturing Polytechnic of Ceper, Klaten, Indonesia
Tomasz Szymczak - Lodz University of Technology, Poland
Marek Tkocz - Silesian University of Technology, Gliwice, Poland
Andrzej Trytek - Rzeszow University of Technology, Poland
Jacek Trzaska - Silesian University of Technology, Gliwice, Poland
Robert B Tuttle - Western Michigan University, United States
Muhammet Uludag - Selcuk University, Turkey
Seyed Ebrahim Vahdat - Ayatollah Amoli Branch, Islamic Azad University, Amol, Iran
Tomasz Wrobel - Silesian University of Technology, Gliwice, Poland
Ryszard Władysiak - Lodz University of Technology, Poland
Antonin Zadera - Brno University of Technology, Czech Republic
Renata Zapała - AGH University of Science and Technology, Kraków, Poland
Bo Zhang - Hunan University of Technology, China
Xiang Zhang - Wuhan University of Science and Technology, China
Eugeniusz Ziółkowski - AGH University of Science and Technology, Kraków, Poland
Sylwia Żymankowska-Kumon - AGH University of Science and Technology, Kraków, Poland
Andrzej Zyska - Czestochowa University of Technology, Poland



List of Reviewers 2020

Shailee Acharya - S. V. I. T Vasad, India
Mohammad Azadi - Semnan University, Iran
Rafał Babilas - Silesian University of Technology, Gliwice, Poland
Czesław Baron - Silesian University of Technology, Gliwice, Poland
Dariusz Bartocha - Silesian University of Technology, Gliwice, Poland
Emin Bayraktar - Supmeca/LISMMA-Paris, France
Jaroslav Beňo - VSB-Technical University of Ostrava, Czech Republic
Artur Bobrowski - AGH University of Science and Technology, Kraków, Poland
Grzegorz Boczkal - AGH University of Science and Technology, Kraków, Poland
Wojciech Borek - Silesian University of Technology, Gliwice, Poland
Pedro Brito - Pontifical Catholic University of Minas Gerais, Brazil
Marek Bruna - University of Žilina, Slovak Republic
John Campbell - University of Birmingham, United Kingdom
Ganesh Chate - Gogte Institute of Technology, India
L.Q. Chen - Northeastern University, China
Mirosław Cholewa - Silesian University of Technology, Gliwice, Poland
Khanh Dang - Hanoi University of Science and Technology, Viet Nam
Vladislav Deev - Wuhan Textile University, China
Brij Dhindaw - Indian Institute of Technology Bhubaneswar, India
Derya Dispinar - Istanbul Technical University, Turkey
Malwina Dojka - Silesian University of Technology, Gliwice, Poland
Rafał Dojka - ODLEWNIA RAFAMET Sp. z o. o., Kuźnia Raciborska, Poland
Anna Dolata - Silesian University of Technology, Gliwice, Poland
Agnieszka Dulska - Silesian University of Technology, Gliwice, Poland
Tomasz Dyl - Gdynia Maritime University, Poland
Maciej Dyzia - Silesian University of Technology, Gliwice, Poland
Eray Erzi - Istanbul University, Turkey
Katarzyna Gawdzińska - Maritime University of Szczecin, Poland
Sergii Gerasin - Pryazovskyi State Technical University, Ukraine
Dipak Ghosh - Forace Polymers Ltd, India
Marcin Górny - AGH University of Science and Technology, Kraków, Poland
Marcin Gołąbczak - Lodz University of Technology, Poland
Beata Grabowska - AGH University of Science and Technology, Kraków, Poland
Adam Grajcar - Silesian University of Technology, Gliwice, Poland
Grzegorz Gumienny - Technical University of Lodz, Poland
Libor Hlavac - VSB Ostrava, Czech Republic
Mariusz Holtzer - AGH University of Science and Technology, Kraków, Poland
Philippe Jacquet - ECAM, Lyon, France
Jarosław Jakubski - AGH University of Science and Technology, Kraków, Poland
Damian Janicki - Silesian University of Technology, Gliwice, Poland
Witold Janik - Silesian University of Technology, Gliwice, Poland
Robert Jasionowski - Maritime University of Szczecin, Poland
Jan Jezierski - Silesian University of Technology, Gliwice, Poland
Jadwiga Kamińska - Łukasiewicz Research Network – Krakow Institute of Technology, Poland
Justyna Kasinska - Kielce University Technology, Poland
Magdalena Kawalec - Akademia Górniczo-Hutnicza, Kraków, Poland
Angelika Kmita - AGH University of Science and Technology, Kraków, Poland
Ladislav Kolařík -Institute of Engineering Technology CTU in Prague, Czech Republic
Marcin Kondracki - Silesian University of Technology, Gliwice, Poland
Sergey Konovalov - Samara National Research University, Russia
Aleksandra Kozłowska - Silesian University of Technology, Gliwice, Poland
Janusz Krawczyk - AGH University of Science and Technology, Kraków, Poland
Halina Krawiec - AGH University of Science and Technology, Kraków, Poland
Ivana Kroupová - VSB - Technical University of Ostrava, Czech Republic
Agnieszka Kupiec-Sobczak - Cracow University of Technology, Poland
Tomasz Lipiński - University of Warmia and Mazury in Olsztyn, Poland
Aleksander Lisiecki - Silesian University of Technology, Gliwice, Poland
Krzysztof Lukaszkowicz - Silesian University of Technology, Gliwice, Poland
Mariusz Łucarz - AGH University of Science and Technology, Kraków, Poland
Katarzyna Major-Gabryś - AGH University of Science and Technology, Kraków, Poland
Pavlo Maruschak - Ternopil Ivan Pului National Technical University, Ukraine
Sanjay Mohan - Shri Mata Vaishno Devi University, India
Marek Mróz - Politechnika Rzeszowska, Rzeszów, Poland
Sebastian Mróz - Czestochowa University of Technology, Poland
Kostiantyn Mykhalenkov - National Academy of Science of Ukraine, Ukraine
Dawid Myszka - Politechnika Warszawska, Warszawa, Poland
Maciej Nadolski - Czestochowa University of Technology, Częstochowa, Poland
Konstantin Nikitin - Samara State Technical University, Russia
Daniel Pakuła - Silesian University of Technology, Gliwice, Poland


This page uses 'cookies'. Learn more