Applied sciences

Archive of Mechanical Engineering

Content

Archive of Mechanical Engineering | 2021 | vol. 68 | No 2

Download PDF Download RIS Download Bibtex

Abstract

The perspective of the current analysis is to represent the incompressible viscous flow past a low permeable spheroid contained in a fictitious spheroidal cell. Stokes approximation and Darcy’s equation are adopted to govern the flow in the fluid and permeable zone, respectively. Happel’s and Kuwabara’s cell models are employed as the boundary conditions at the cell surface. At the fluid porous interface, we suppose the conditions of conservation of mass, balancing of pressure component at the permeable area with the normal stresses in the liquid area, and the slip condition, known as Beavers-Joseph-Saffman-Jones condition to be well suitable. A closed-form analytical expression for hydrodynamic drag on the bounded spheroidal particle is determined and therefore, mobility of the particle is also calculated, for both the case of a prolate as well as an oblate spheroid. Several graphs and tables are plotted to observe the dependence of normalized mobility on pertinent parameters including permeability, deformation, the volume fraction of the particle, slip parameter, and the aspect ratio. Significant results that influence the impact of the above parameters in the problem have been pointed out. Our work is validated by referring to previous results available in literature as reduction cases.
Go to article

Bibliography

[1] D.A. Nield and A. Bejan. Convection in Porous Media. Springer, New York, 2006.
[2] H.P.G. Darcy. Les Fontaines Publiques de la Ville de Dijon. Victor Delmont, Paris, 1856.
[3] H.C. Brinkman. A calculation of viscous force exerted by flowing fluid on dense swarm of particles. Applied Science Research, 1:27-34, 1949. doi: 10.1007/BF02120313.
[4] D.D. Joseph and L.N. Tao. The effect of permeability on the slow motion of a porous sphere. Journal of Applied Mathematics and Mechanics, 44(8-9):361-364, 1964. doi: 10.1002/zamm.19640440804.
[5] D.N. Sutherland and C.T. Tan. Sedimentation of a porous sphere. Chemical Engineering Science, 25(12):1948-1950, 1970. doi: 10.1016/0009-2509(70)87013-0.
[6] M.P. Singh and J.L. Gupta. The effect of permeability on the drag of a porous sphere in a uniform stream. Journal of Applied Mathematics and Mechanics, 51(1):27-32, 1971. doi: zamm.19710510103.
[7] I.P. Jones. Low Reynolds number flow past a porous spherical shell. Mathematical Proceedings of the Cambridge Philosophical Society, 73(1):231-238, 1973. doi: 10.1017/S0305004100047642.
[8] G. Neale, N. Epstein, and W. Nader. Creeping flow relative to permeable spheres. Chemical Engineering Science, 28(10):1865-1874, 1973. doi: 10.1016/0009-2509(73)85070-5.
[9] V.M. Shapovalov. Viscous fluid flow around a semipermeable particle. Journal of Applied Mechanics and Technical Physics, 50(4):584-588, 2009. doi: 10.1007/s10808-009-0079-x.
[10] G.S. Beavers and D.D. Joseph. Boundary conditions at a naturally permeable wall. Journal of Fluid Mechanics, 30(1):197-207, 1967. doi: 10.1017/S0022112067001375.
[11] P.G. Saffman. On the boundary condition at the surface of a porous medium. Studies in Applied Mathematics, 50(2):93-101, 1971. doi: 10.1002/sapm197150293.
[12] S. Khabthani, A. Sellier, and F. Feuillebois. Lubricating motion of a sphere towards a thin porous slab with Saffman slip condition. Journal of Fluid Mechanics, 867:949-968, 2019. doi: 10.1017/jfm.2019.169.
[13] M.C. Lai, M.C. Shiue, and K.C. Ong. A simple projection method for the coupled Navier-Stokes and Darcy flows. Computational Geosciences, 23:21-33, 2019. doi: 10.1007/s10596-018-9781-1.
[14] J. Happel and H. Brenner. Low Reynolds Number Hydrodynamics. Englewood Cliffs New Jork, Prentice-Hall, 1965.
[15] J. Happel. Viscous flow in multiparticle systems: slow motion of fluids relative to beds of spherical particles. American Institute of Chemical Engineers Journal, 4(2):197-201, 1958. doi: 10.1002/aic.690040214.
[16] S. Kuwabara. The forces experienced by randomly distributed parallel circular cylinders or spheres in a viscous flow at small Reynolds numbers. Journal of the Physical Society of Japan, 14(4):527-532,1959. doi: 10.1143/JPSJ.14.527.
[17] S.B. Chen and X. Ye. Boundary effect on slow motion of a composite sphere perpendicular to two parallel impermeable plates. Chemical Engineering Science, 55(13):2441-2453, 2000. doi: 10.1016/S0009-2509(99)00509-6.
[18] D. Srinivasacharya. Motion of a porous sphere in a spherical container. Comptes Rendus Mecanique, 333(8):612-616, 2005. doi: 10.1016/j.crme.2005.07.017.
[19] S.I. Vasin, A.N. Fillipov, and V.M. Starov. Hydrodynamic permeability of membranes built up by particles covered by porous shells: Cell models. Advances in Colloid Interface Science, 139(1-2):83-96, 2008. doi: 10.1016/j.cis.2008.01.005.
[20] P.K. Yadav, A. Tiwari, S. Deo, A. Filippov, and S. Vasin. Hydrodynamic permeability of membranes built up by spherical particles covered by porous shells: effect of stress jump condition. Acta Mechanica, 215:193-209, 2010. doi: 10.1007/s00707-010-0331-8.
[21] J. Prakash, G.P. Raja Sekhar, and M. Kohr. Stokes flow of an assemblage of porous particles: stress jump condition. Zeitschrift für angewandte Mathematik und Physik, 62:1027-1046, 2011. doi: 10.1007/s00033-011-0123-6.
[22] E.I. Saad. Stokes flow past an assemblage of axisymmetric porous spherical shell-in-cell models: effect of stress jump condition. Meccanica, 48:1747-1759, 2013. doi: 10.1007/s11012-013-9706-y.
[23] J. Prakash and G.P. Raja Sekhar. Estimation of the dynamic permeability of an assembly of permeable spherical porous particle using cell model. Journal of Engineering Mathematics, 80:63-73, 2013. doi: 10.1007/s10665-012-9580-y.
[24] M.K. Prasad and T. Bucha. Creeping flow of fluid sphere contained in a spherical envelope: magnetic effect. SN Applied Science, 1(12):1594, 2019. doi: 10.1007/s42452-019-1622-x.
[25] M.K. Prasad and T. Bucha. Magnetohydrodynamic creeping flow around a weakly permeable spherical particle in cell models. Pramana - Journal of Physics, 94(1):1-10, 2020. doi: 10.1007/s12043-019-1892-2.
[26] M.K. Prasad and T. Bucha. MHD viscous flow past a weakly permeable cylinder using Happel and Kuwabara cell models. Iranian Journal of Science and Technology Transaction A: Science, 44:1063-1073, 2020. doi: 10.1007/s40995-020-00894-4.
[27] D. Khanukaeva. Filtration of micropolar liquid through a membrane composed of spherical cells with porous layer. Theoretical and Computational Fluid Dynamics, 34(3):215-229, 2020. doi: 10.1007/s00162-020-00527-x.
[28] M.K. Prasad. Boundary effects of a nonconcentric semipermeable sphere using Happel and Kuwabara cell models. Applied and Computational Mechanics, 15:1-12, 2021. doi: 10.24132/acm.2021.620.
[29] G.G. Stokes. On the effect of the internal friction of fluids on the motion of pendulums. Proceedings of Cambridge Philosophical Society, 9:8-106, 1851.
[30] C.R. Reddy and N. Kishore. Momentum and heat transfer phenomena of confined spheroid particles in power-law liquids, Industrial and Engineering Chemical Research, 53(2):989-998, 2014. doi: 10.1021/ie4032428.
[31] A. Acrivos and T.D. Taylor. The Stokes flow past an arbitrary particle: the slightly deformed sphere. Chemical Engineering Science, 19(7):445-451, 1964. doi: 10.1016/0009-2509(64)85071-5.
[32] H. Ramkissoon. Stokes flow past a slightly deformed fluid sphere, Journal of Applied Mathematics and Physics, 37:859-866, 1986. doi: 10.1007/BF00953677.
[33] D. Palaniappan. Creeping flow about a slightly deformed sphere. Zeitschrift für angewandte Mathematik und Physik, 45:832-838, 1994. doi: 10.1007/BF00942756.
[34] G. Dassios, M. Hadjinicolaou, F.A. Coutelieris, and A.C. Payatakes. Stokes flow in spheroidal particle-in-cell models with Happel and Kuwabara boundary conditions. International Journal of Engineering Science, 33(10):1465-1490, 1995. doi: 10.1016/0020-7225(95)00010-U.
[35] H. Ramkissoon. Slip flow past an approximate spheroid. Acta Mechanica, 123:227-233, 1997. doi: 10.1007/BF01178412.
[36] T. Zlatanovski. Axi-symmetric creeping flow past a porous prolate spheroidal particle using the Brinkman model. The Quarterly Journal of Mechanics and Applied Mathematics, 52(1):111-126, 1999. doi: 10.1093/qjmam/52.1.111.
[37] S. Deo and S. Datta. Slip flow past a prolate spheroid. Indian Journal of Pure and Applied Mathematics, 33(6):903-909, 2002.
[38] P. Vainshtein, M. Shapiro, and C. Gutfinger. Creeping flow past and within a permeable spheroid. International Journal of Multiphase Flow, 28(12):1945-1963, 2002. doi: 10.1016/S0301-9322(02)00106-4.
[39] H. Ramkissoon and K. Rahaman. Wall effects on a spherical particle. International Journal of Engineering Science, 41(3-5), 283-290, 2003. doi: 10.1016/S0020-7225(02)00209-4.
[40] S. Senchenko and H.J. Keh. Slipping Stokes flow around a slightly deformed sphere. Physics of Fluids, 18(8):088104, 2006. doi: 10.1063/1.2337666.
[41] D. Srinivasacharya. Flow past a porous approximate spherical shell, Zeitschrift für angewandte Mathematik und Physik, 58, 646-658, 2007. doi: 10.1007/s00033-006-6003-9.
[42] Y.C. Chang and H.J. Keh. Translation and rotation of slightly deformed colloidal spheres experiencing slip. Journal of Colloid and Interface Science, 330:201-210, 2009. doi: 10.1016/j.jcis.2008.10.055.
[43] E.I. Saad. Translation and rotation of a porous spheroid in a spheroidal container. Canadian Journal of Physics, 88(9):689-700, 2010. doi: 10.1139/P10-040.
[44] E.I. Saad. Stokes flow past an assemblage of axisymmetric porous spheroidal particle in cell models. Journal of Porous Media, 15(9):849-866, 2012. doi: /10.1615/JPorMedia.v15.i9.40.
[45] D. Srinivasacharya and M.K. Prasad. Axisymmetric creeping motion of a porous approximate sphere with an impermeable core. The European Physics Journal Plus, 128(1):9, 2013. doi: 10.1140/epjp/i2013-13009-1.
[46] D. Srinivasacharya and M.K. Prasad. Creeping motion of a porous approximate sphere with an impermeable core in a spherical container. European Journal of Mechanics - B/Fluids, 36:104-114, 2012. doi: 10.1016/j.euromechflu.2012.04.001.
[47] D. Srinivasacharya and M.K. Prasad. Axisymmetric motion of a porous approximate sphere in an approximate spherical container. Archive of Mechanics, 65(6):485-509, 2013.
[48] K.P. Chen. Fluid extraction from porous media by a slender permeable prolate-spheroid. Extreme Mechanics Letter, 4:124-130, 2015. doi: 10.1016/j.eml.2015.06.001.
[49] M. Rasoulzadeh and F.J. Kuchuk. Effective permeability of a porous medium with spherical and spheroidal vug and fracture inclusions. Transport in Porous Media, 116:613-644, 2017. doi: 10.1007/s11242-016-0792-x.
[50] P.K. Yadav, A. Tiwari, and P. Singh. Hydrodynamic permeability of a membrane built up by spheroidal particles covered by porous layer. Acta Mechanica, 229:1869-1892, 2018. doi: 10.1007/s00707-017-2054-6.
[51] M.K. Prasad and T. Bucha. Steady viscous flow around a permeable spheroidal particle. International Journal of Applied and Computational Mathematics, 5:109, 2019. doi: 10.1007/s00707-017-2054-6.
[52] M.K. Prasad and T. Bucha. Effect of magnetic field on the slow motion of a porous spheroid: Brinkman's model. Archive of Applied Mechanics, 91:1739-1755, 2021. doi: 10.1007/s00419-020-01852-7.
[53] J.D. Sherwood. Cell models for suspension viscosity. Chemical Engineering Science, 61(10):6727-6731, 2006. doi: 10.1016/j.ces.2006.07.016.
[54] A. Tiwari, P.K. Yadav, and P. Singh. Stokes flow through assemblage of non homogeneous porous cylindrical particle using cell model technique. National Academy of Science Letters, 41(1):53-57, 2018. doi: 10.1007/s40009-017-0605-y.
[55] H.H. Sherief, M.S. Faltas, and E.I. Saad. Slip at the surface of an oscillating spheroidal particle in a micropolar fluid. ANZIAM Journal, 55(E):E1-E50, 2013. doi: 10.21914/anziamj.v55i0.6813.
Go to article

Authors and Affiliations

Tina Bucha
1
ORCID: ORCID
Madasu Krishna Prasad
2
ORCID: ORCID

  1. Department of Mathematics, National Institute of Technology, Raipur, Chhattisgarh, India
  2. Department of Mathematics, National Institute of Technology, Raipur-492010, Chhattisgarh, India
Download PDF Download RIS Download Bibtex

Abstract

The present theoretical study is concerned with the analysis of surface roughness effects on the steady-state performance of stepped circular hydrostatic thrust bearings lubricated with non-Newtonian fluids: Rabinowitsch fluid model. To take the effects of surface roughness into account, Christensen’s theory for rough surfaces has been adopted. The expression for pressure gradient has been derived in stochastic form employing the energy integral approach. Results for stochastic film pressure and load-carrying capacity have been plotted and analyzed based on numerical results. Due to surface roughness, significant variations in the theoretical results of these properties have been observed.
Go to article

Bibliography

[1] U.P. Singh, R.S. Gupta, and V.K. Kapur. On the steady performance of hydrostatic thrust bearing: Rabinowitsch fluid model. Tribology Transactions, 54(5):723-729, 2011. doi: 10.1080/10402004.2011.597541.
[2] U.P. Singh, R.S. Gupta, and V.K. Kapur. On the application of Rabinowitsch fluid model on an annular ring hydrostatic thrust bearing. Tribology International, 58:65-70, 2013. doi: 10.1016/j.triboint.2012.09.014.
[3] U.P. Singh, R.S. Gupta, and V.K. Kapur. On the steady performance of annular hydrostatic thrust bearing: Rabinowitsch fluid model. Journal of Tribology, 134(4):044502, 2012. doi: 10.1115/1.4007350.
[4] B.J. Hamrock, S.R. Schmid, and B.O. Jacobson. Fundamentals of Fluid Film Lubrication. CRC Press, 2004. doi: 10.1201/9780203021187.
[5] R. Bassani and P. Piccigallo. Hydrostatic Lubrication, Elsevier, 1992.
[6] J.A. Coombs and D. Dowson. An experimental investigation of the effects of lubricant inertia in a hydrostatic thrust bearing. Proceedings of the Institution of Mechanical Engineers, Conference Proceedings, 179(10):96-114, 1964. doi: 10.1243/PIME_CONF_1964_179_270_02.
[7] J. Peterson, W.E. Finn, and D.W. Dareing. Non-Newtonian temperature and pressure effects of a lubricant slurry in rotating hydrostatic step bearing. Tribology Transactions, 37(4):857-863, 1994. doi: 10.1080/10402009408983369.
[8] V.K. Kapur and K. Verma. The simultaneous effects of inertia and temperature on the performance of a hydrostatic thrust bearing. Wear, 54(1):113-122, 1979. doi: 10.1016/0043-1648(79)90050-4.
[9] P. Singh, B.D. Gupta, and V.K. Kapur. Design criteria for stepped thrust bearings. Wear, 89(1):41-55, 1983. doi: 10.1016/0043-1648(83)90213-2.
[10] S.C. Sharma, S.C. Jain, and D.K. Bharuka. Influence of recess shape on the performance of a capillary compensated circular thrust pad hydrostatic bearing. Tribology International, 35(6):347-356, 2002. doi: 10.1016/S0301-679X(02)00013-0.
[11] Z. Tian, H. Cao, and Y. Huang. Static characteristics of hydrostatic thrust bearing considering the inertia effect on the region of supply hole. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 233(1):188-193, 2019. doi: 10.1177/1350650118773944.
[12] Y.K. Younes. A revised design of circular hydrostatic bearings for optimal pumping power. Tribology International, 26(3):195-200, 1993. doi: 10.1016/0301-679X(93)90093-G.
[13] O.J. Bakker and R.A.J. van Ostayen. Recess depth optimization for rotating, annular, and circular recess hydrostatic thrust bearings. Journal of Tribology, 132(1):011103, 2010. doi: 10.1115/1.4000545.
[14] H. Sawano, Y. Nakamura, H. Yoshioka, and H. Shinno. High performance hydrostatic bearing using a variable inherent restrictor with a thin metal plate. Precision Engineering, 41:78-85, 2015. doi: 10.1016/j.precisioneng.2015.02.001.
[15] J.S. Yadav and V.K. Kapur. On the viscosity variation with temperature and pressure in thrust bearing. International Journal of Engineering Science, 19(2):269-77, 1981. doi: 10.1016/0020-7225(81)90027-6.
[16] P. Zhicheng, S. Jingwu, Z. Wenjie, L. Qingming, and C. Wei. The dynamic characteristics of hydrostatic bearings. Wear, 166(2):215-220, 1993. doi: 10.1016/0043-1648(93)90264-M.
[17] J.R. Lin. Static and dynamic characteristics of externally pressurized circular step thrust bearings lubricated with couple stress fluids. Tribology International, 32(4):207-216, 1999. doi: 10.1016/S0301-679X(99)00034-1.
[18] H. Christensen. Stochastic models for hydrodynamic lubrication of rough surfaces. Proceedings of the Institution of Mechanical Engineers, 184(1):1013-1026, 1969. doi: 10.1243/PIME_ PROC_1969_184_074_02.
[19] J. Prakash and K. Tiwari. Effect of surface roughness on the squeeze film between rotating porous annular discs with arbitrary porous wall thickness. International Journal of Mechanical Sciences, 27(3):135-144, 1985. doi: 10.1016/0020-7403(85)90054-2.
[20] P. Singh, B.D. Gupta, and V.K. Kapur. Optimization of corrugated thrust bearing characteristics. Wear, 167(2):109-120, 1993. doi: 10.1016/0043-1648(93)90315-D.
[21] J.R. Lin. Surface roughness effect on the dynamic stiffness and damping characteristics of compensated hydrostatic thrust bearings. International Journal of Machine Tools and Manufacture, 40(11):1671-1689, 2000. doi: 10.1016/S0890-6955(00)00012-2.
[22] A.W. Yacout. The surfacse roughness effect on the hydrostatic thrust spherical bearings performance: Part 3 of 5 - Recessed clearance type of bearings. In Proceedings of the ASME International Mechanical Enginering Congress and Exposition, Volume 9: Mechanical Systems and Control, Parts A, B, and C, pages 431-447, Seattle, Washington, USA, November 11-15, 2007. doi: 10.1115/IMECE2007-41013.
[23] Y. Xuebing, X. Wanli, L. Lang, and H. Zhiquan. Analysis of the combined effect of the surface roughness and inertia on the performance of high-speed hydrostatic thrust bearing. In: Luo J., Meng Y., Shao T., Zhao Q. (eds): Advanced Tribology, 197-201, Springer, 2009. doi: 10.1007/978-3-642-03653-8_66.
[24] A. Walicka, E. Walicki, P. Jurczak, and J. Falicki. Thrust bearing with rough surfaces lubricated by an Ellis fluid. International Journal of Applied Mechanics and Engineering, 19(4):809-822, 2014. doi: 10.2478/ijame-2014-0056.
[25] V.K. Stokes. Couple stress in fluids. The Physics of Fluids, 9(9):1709-1715, 1966. doi: 10.1063/1.1761925.
[26] S. Wada and H. Hayashi. Hydrodynamic lubrication of journal bearings by pseudo-plastic lubricants: Part 2, Experimental studies. Bulletin of JSME, 14(69):279-286, 1971. doi: 10.1299/jsme1958.14.279.
[27] H.A. Spikes. The behaviour of lubricants in contacts: current understanding and future possibilities. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 208(1):3-15, 1994. doi: 10.1243/PIME_PROC_1994_208_345_02.
[28] P. Bourging and B. Gay. Determination of the load capacity of finite width journal bearing by finite element method in the case of a non-Newtonian lubricant. Journal of Tribology, 106(2):285-290, 1984. doi: 10.1115/1.3260906.
[29] H. Hayashi and S. Wada. Hydrodynamic lubrication of journal bearings by pseudo-plastic lubricants: Part 3, Theoretical analysis considering effects of correlation. Bulletin of JSME, 17(109):967-974, 1974. doi: 10.1299/jsme1958.17.967.
[30] H. Hashimoto and S. Wada. The effects of fluid inertia forces in parallel circular squeeze film bearings lubricated with pseudo-plastic fluids. Journal of Tribology, 108(2):282-287, 1986. doi: 10.1115/1.3261177.
[31] J.-R. Lin. Non-Newtonian effects on the dynamic characteristics of one dimensional slider bearings: Rabinowitsch fluid model. Tribology Letters, 10:237-243, 2001. doi: 10.1023/A:1016678208150.
[32] U.P. Singh, R.S. Gupta, and V.K. Kapur. Effects of inertia in the steady state pressurised flow of a non-Newtonian fluid between two curvilinear surfaces of revolution: Rabinowitsch fluid model. Chemical and Process Engineering, 32(4):333-349, 2011. doi: 10.2478/v10176-011-0027-1.
[33] J.R. Lin. Non-Newtonian squeeze film characteristics between parallel annular disks: Rabinowitsch fluid model. Tribology International, 52:190-194, 2012. doi: 10.1016/j.triboint. 2012.02.017.
[34] U.P. Singh. Application of Rabinowitsch fluid model to pivoted curved slider bearings. Archive of Mechanical Engineering, 60(2):247-266, 2013. doi: 10.2478/meceng-2013-0016.
[35] U.P. Singh and R.S. Gupta. Dynamic performance characteristics of a curved slider bearing operating with ferrofluids. Advances in Tribology, 2012:1-6, 2012. doi: 10.1155/2012/278723.
[36] U.P. Singh, R.S. Gupta, and V.K. Kapur. On the squeeze film characteristics between a long cylinder and a flat plate: Rabinowitsch model. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 227(1):34-42, 2013. doi: 10.1177/1350650112458742.
[37] S.C. Sharma and S.K. Yadav. Performance of hydrostatic circular thrust pad bearing operating with Rabinowitsch fluid model. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 227(11):1272-1284, 2013. doi: 10.1177/1350650113490147.
[38] Y. Huang and Z. Tian. A new derivation to study the steady performance of hydrostatic thrust bearing: Rabinowitch fluid model. Journal of Non-Newtonian Fluid Mechanics, 246:31-35, 2017. doi: 10.1016/j.jnnfm.2017.04.012.
[39] U.P. Singh, P. Sinha, and M. Kumar. Analysis of hydrostatic rough thrust bearing lubricated with Rabinowitsch fluid considering fluid inertia in supply region. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tibology, 235(2):386-395, 2021. doi: 10.1177/1350650120945887.
[40] A. Cameron. Basic Lubrication Theory, 3rd edition. E. Horwood, 1981.
Go to article

Authors and Affiliations

Udaya P. Singh
1
ORCID: ORCID

  1. Rajkiya Engineering College, Sonbhadra, Uttar Pradesh, India
Download PDF Download RIS Download Bibtex

Abstract

Operating cranes is challenging because payloads can experience large and dangerous oscillations. Anti-sway control of crane payload can be approached by the active methods, such as feedback control, or passive methods. The feedback control uses the feedback measurement of swing vibration to produce the command sent to a motor. The feedback control shows good effectiveness, but conflict with the actions of the human operator is a challenge of this method. The passive method uses the spring-damper to dissipate energy. The passive method does not cause conflict with the human operator but has limited performance. This paper presents the combination of two methods to overcome the disadvantages of each separate one. The passive method is used to improve the efficiency of the feedback method to avoid conflicts with the human operator. The effectiveness of the combination is simulated in a 2D crane model.
Go to article

Bibliography


[1] D. Kim and Y. Park. Tracking control in x-y plane of an offshore container crane. Journal of Vibration and Control, 23(3):469-483, 2017. doi: 10.1177/1077546315581091.
[2] D.H. Kim and J.W. Lee. Model-based PID control of a crane spreader by four auxiliary cables. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 220(8):1151-1165, 2006. doi: 10.1243/09544062JMES120.
[3] N. Uchiyama. Robust control of rotary crane by partial-state feedback with integrator. Mechatronics, 19(8):1294-1302, 2009. doi: 10.1016/j.mechatronics.2009.08.007.
[4] J. Smoczek. Fuzzy crane control with sensorless payload deflection feedback for vibration reduction. Mechanical Systems and Signal Processing, 46(1):70–81, 2014. doi: 10.1016/j.ymssp.2013.12.012.
[5] M. Zhang, X. Ma, X. Rong, X. Tian, and Y. Li. Adaptive tracking control for double-pendulum overhead cranes subject to tracking error limitation, parametric uncertainties and external disturbances. Mechanical Systems and Signal Processing, 76-77:15–32, 2016. doi: 10.1016/j.ymssp.2016.02.013.
[6] L.D. Viet and K.T. Nguyen. Combination of input shaping and radial spring-damper to reduce tridirectional vibration of crane payload. Mechanical Systems and Signal Processing, 116:310-321, 2019. doi: 0.1016/j.ymssp.2018.06.056.
[7] L.D. Viet and Y. Park. A cable-passive damper system for sway and skew motion control of a crane spreader. Shock and Vibration, 2015:507549, 2015. doi: 10.1155/2015/507549.
[8] L.D. Viet. Crane sway reduction using Coriolis force produced by radial spring and damper. Journal of Mechanical Science and Technology, 29(3):973-979, 2015. doi: 10.1007/s12206-015-0211-1.
[9] J. Vaughan, E. Maleki, and W. Singhose. Advantages of using command shaping over feedback for crane control. Proceedings of the 2010 American Control Conference, pages 2308-2313, 2010. doi: 10.1109/ACC.2010.5530548.
[10] J. Vaughan, A. Yano, and W. Singhose. Comparison of robust input shapers. Journal of Sound and Vibration, 315(4-5):797–815, 2008. doi: 10.1016/j.jsv.2008.02.032.
[11] W. Singhose. Command shaping for flexible systems: A review of the first 50 years. International Journal of Precision Engineering and Manufacturing, 10(4):153-168, 2009. doi: 10.1007/s12541-009-0084-2.
[12] J. Lawrence and W. Singhose. Command shaping slewing motions for tower cranes. Journal of Vibration and Acoustics, 132(1):011002, 2010. doi: 10.1115/1.3025845.
[13] D. Blackburn, W. Singhose, J. Kitchen, V. Patrangenaru, J. Lawrence, K. Tatsuaki, and A. Taura. Command shaping for nonlinear crane dynamics. Journal of Vibration and Control, 16(4):477-501, 2010. doi: 10.1177/1077546309106142.
[14] J. Huang, E. Maleki, and W. Singhose. Dynamics and swing control of mobile boom cranes subject to wind disturbances, IET Control Theory and Applications, 7(9):1187–1195, 2013. doi: 10.1049/iet-cta.2012.0957.
[15] R. Schmidt, N. Barry, and J. Vaughan. Tracking of a target payload via a combination of input shaping and feedback control. IFAC-PapersOnLine, 48(12):141-146, 2015. doi: 10.1016/j.ifacol.2015.09.367.
[16] N.D. Anh, H. Matsuhisa, L.D. Viet, and M. Yasuda. Vibration control of an inverted pendulum type structure by passive mass-spring-pendulum dynamic vibration absorber. Journal of Sound and Vibration, 307(1-2):187-201, 2007. doi: 10.1016/j.jsv.2007.06.060.
[17] Function Bay Inc., http://www.functionbay.co.kr/, last checked 27 May 2020.
Go to article

Authors and Affiliations

Trong Kien Nguyen
1

  1. Faculty of Civil Engineering, Vinh University, Vinh City, Nghe An, Vietnam
Download PDF Download RIS Download Bibtex

Abstract

The paper presents a numerical analysis carried out to determine the influence of the ground surface fire on the strain level of shelter housing with the ground cover. It is assumed that the underground shelter is longitudinal and the fire spans on an extensive area. The area surrounding the housing was treated as a material with average constant thermodynamic values. The heating and cooling processes were described on the basis of the Fourier’s equation concerning heat conduction in consideration on material, ground and concrete heterogeneous nature. The numeric analysis was carried out in two stages. In the first stage, a quasi-stationary initial temperature distribution was sought in the ground centre and shelter shield. In the second stage of analysis, the fire effect was considered according to the time profile of temperature variation in object.
Go to article

Bibliography

[1] A. Dorsz, A. Rusowicz, and A. Prawdzik. Comparative analysis of assumptions for numerical simulation of the effects of fire – safety of evacuation from the building structure. Inżynieria Bezpieczeństwa Obiektów Antropogenicznych, 4(2020):212–226, 2020. doi: 10.37105/iboa.89.
[2] A. Asgary, A.S. Naini, and J. Levy. Intelligent security systems engineering for modeling fire critical incidents: towards sustainable security. Journal of Systems Science and Systems Engineering, 18(4):477–488, 2009. doi: 10.1007/s11518-009-5121-2.
[3] J.L. Coen. Some new basics of fire behavior. Fire Management Today, 71(1):38–43, 2011.
[4] T. Putnam and B.W. Butler. Evaluating fire shelter performance in experimental crown fires. Canadian Journal of Forest Research, 34(8):1600–1615, 2004. doi: 10.1139/X04-091.
[5] E. Ozbay, Ö. Çavus, and B.Y. Kara. Shelter site location under multi-hazard scenarios. Computers and Operations Research, 106:102–118, 2019. doi: 10.1016/j.cor.2019.02.008.
[6] R. Linn, K. Anderson, J. Winterkamp, A. Brooks, M. Wotton, J-L. Dupuy, F. Pimont, and C. Edminster. Incorporating field wind data into FIRETEC simulations of the International Crown Fire Modeling Experiment (ICFME): preliminary lessons learned. Canadian Journal of Forest Research, 42(5):879–898, 2012. doi: 10.1139/X2012-038.
[7] Ch. Zhang, J.G. Silva, C. Weinschenk, D. Kamikawa, and Y. Hasemi. Simulation methodology for coupled fire-structure analysis: modeling localized fire tests on a steel column. Fire Technology, 52:239–262, 2016. doi: 10.1007/s10694-015-0495-9.
[8] T. Molkens and B. Rossi. On the simulation of real fire for post fire resistance evaluation of steel structures. Fire Technology, 57:839–871, 2021. doi: 10.1007/s10694-020-01025-6.
[9] N. Johansson, J. Anderson, R. McNamee, and Ch. Pelo. A Round Robin of fire modelling for performance-based design. Fire and Materials, 2020;1–14, doi: 10.1002/fam.2891.
[10] J. Lu, T. Wang, L. Wang, W. Chen, and Y. Chen. Optimization of duct structure and analysis of its impact on temperature inside the shelter. Journal of Physics: Conference Series, 1300:012011, 2019. doi: 10.1088/1742-6596/1300/1/012011.
[11] A.Baryłka. The impact of fire on changing the strength of the underground shelter structure. Rynek Energii, 146(1):71–75, 2020.
[12] T.J. Cova, P.E. Dennison, and F.A. Drews. Modeling evacuate versus shelter-in-place decisions in wildfires. Sustainability, 3(10):1662–1687, 2011. doi: 10.3390/su3101662.
[13] M.D. Lulea, V. Iordache, and I. Năstase. Fire modeling in a nonventilated corridor. E3S Web of Conferences, 32:01011, 2018. doi: 10.1051/e3sconf/20183201011.
[14] C. Salter. Fire modelling within cloud based resources. Fire Technology, 51:491–497, 2015. doi: 10.1007/s10694-014-0433-2.
[15] M. Krajčír and J. Müllerová. 3D small-scale fire modeling experiments. Procedia Engineering, 192:474–479, 2017. doi: 10.1016/j.proeng.2017.06.082.
[16] Y. Varaksin. Concentrated air and fire vortices: Physical modeling (a review). High Temperature, 54(3):409–427, 2016. doi: 10.1134/S0018151X16030226.
[17] Ch. Lautenberger, G. Rein, and C. Fernandez-Pello. The application of a genetic algorithm to estimate material properties for fire modeling from bench-scale fire test data. Fire Safety Journal, 41(3):204–214, 2006. doi: 0.1016/j.firesaf.2005.12.004.
[18] A. Dorsz and A. Rusowicz. Numerical modelling of the influence of thermal effects on the exhaust fans in the fire ventilation systems. Rynek Energii, 154(3):85–90, 2021. (in Polish).
[19] J.A. Prusiel. Theoretical and experimental analysis of thermal fields distribution in granular media stored in silo model. Acta Agrophysica, 19(2):391–402, 2012. (in Polish).
[20] PN-EN: 1991-1-2:2006 – Actions on structures exposed to fire.
[21] Z. Garncarek and J. Idzik. Degree of heterogeneity of thermal field a method of evaluation. International Journal of Heat and Mass Transfer, 35(11):2769–2775, 1992. doi: 10.1016/0017-9310(92)90297-6.
[22] A. Baryłka and D. Tomaszewicz. Influence of measuring deviations of the components of layered walls on their durability. Inżynieria Bezpieczeństwa Obiektów Antropogenicznych, 3(2020):155–162, 2020.doi: 10.37105/iboa.75.
[23] M. Abramowicz. Design of building structures subject to fire exposure according to Eurocodes. Kalendarz budowlany 2008 r.. Chapter 18. Warszawskie Centrum Postępu Techniczno-Organizacyjnego Budownictwa WACETOB. (in Polish)
[24] A. Baryłka. The issue of the fitness of buildings for use in the issues of safety engineering of these objects. Inżynieria Bezpieczeństwa Obiektów Antropogenicznych, 4, 2019, (in Polish). doi: 10.37105/iboa.31.
[25] A. Baryłka and D. Tomaszewicz. Influence of surface shape of glued anchors on their load capacity. Modern Engineering, 2:78–82, 2020.
[26] E. Kostowski. Heat Flow. WPŚL, Gliwice, 2000. (in Polish).
Go to article

Authors and Affiliations

Adam Baryłka
1
ORCID: ORCID

  1. Centre of Construction Expertise, Warsaw, Poland
Download PDF Download RIS Download Bibtex

Abstract

Heat transfer augmentation has become the utmost industrial desire. Turbulence promoters seems to be a better option for better heat transfer but at the expense of enormous pressure drop. In the current study, experimental optimization of heat transfer and pressure drop in various configurations of ribbed and corrugated surfaces on the bottom wall of the Solar Air Heater channel, having aspect ratio of 26:5 was performed. The results were evaluated in terms of enhancement in heat transfer (Nu/Nu s), friction factor ratio (f/f s) and thermal performance factor ( η). Three different cases and nine configurations with a pitch to rib/corrugation height ratio of 4.0 were studied. Case A consists of a smooth, continuous square rib, inline and staggered broken ribs. Case B comprises 30°, 45°, 60° and 90° trapezoidal corrugated geometries while Case C is the comparison of smooth, wavy corrugated and the best configurations of cases A and B. The results show that rectangular duct with staggered broken ribs and trapezoidal corrugation at 45° are the best configurations for case A and B, respectively. The 45° corrugated configuration is the best one amongst all, with values of 1.53, 1.5 and 1.33% for Nu/Nu s, f/f s and η respectively.
Go to article

Bibliography

[1] W.A. Hermann. Quantifying global exergy resources. Energy, 31(12):1685–1702, 2006. doi: 10.1016/j.energy.2005.09.006.
[2] T. Alam, R.P. Saini, and J.S. Saini. Use of turbulators for heat transfer augmentation in an air duct – A review. Renewable Energy, 62:689–715, 2014. doi: 10.1016/j.renene.2013.08.024.
[3] A. Kumar, R.P. Saini, and J.S. Saini. Heat and fluid flow characteristics of roughened solar air heater ducts – A review. Renewable Energy, 47:77–94, 2012. doi: 10.1016/j.renene.2012.04.001.
[4] D. Kumar and L. Prasad. Heat transfer augmentation of various roughness geometry used in solar air heaters. International Journal of Mechanical Engineering and Technology, 8(12):491–508, 2017.
[5] R. Prakash, A.K. Singh, and P.A. Verma. The effect of roughness geometries on heat transfer enhancement in solar air heater – A review. International Journal on Recent and Innovation Trends in Computing and Communication, 6(4):286–291, 2018.
[6] N.N. Sheikh, B. Kumar, and N.K. Saini. A review paper on pin fin efficiency enhancement. International Journal of Applied Engineering Research, 14(8):108–112, 2019.
[7] M. Sethi, V. Goel, and N.S. Thakur. Correlations for solar air heater duct with dimpled shape roughness elements on absorber plate. Solar Energy, 86(9):2852–2861, 2012. doi: 10.1016/j.solener.2012.06.024.
[8] T.-M. Liou, J.-J. Hwang, and S.-H. Chen. Simulation and measurement of enhanced turbulent heat transfer in a channel with periodic ribs on one principal wall. International Journal of Heat and Mass Transfer, 36(2):507–517, 1993. doi: 10.1016/0017-9310(93)80025-P.
[9] M.A. Al-Nimr. Transient behaviour of a matrix solar air heater. Energy Conversion and Management, 34(8):649–656, 1993. doi: 10.1016/0196-8904(93)90099-V.
[10] A. Kumar, A. Gholap, R. Gangarde, S.M. Shinde, M.P. Vyavahare, V.B. Mete, and S.A. Borude. Performance of solar air heaters with corrugated absorber plate – A CFD approach. International Journal of Innovative Research and Advanced Studies, 4(11):76–86, 2017.
[11] W. Xu, S. Wang, L. Huang, Q. Wang, Q. Zhang, and H. Lu. Thermo-hydraulic performance of Therminol liquid phase heat transfer fluid in a ribbed tube of solar heater. Renewable Energy, 101:919–929, 2017. doi: 10.1016/j.renene.2016.09.043.
[12] C. Sivakandhan, T.V. Arjunan, and M.M. Matheswaran. Thermohydraulic performance enhancement of a new hybrid duct solar air heater with inclined rib roughness. Renewable Energy, 147(1):2345–2357, 2020. doi: 10.1016/j.renene.2019.10.007.
[13] S.K. Dehariya and A.R. Jaurker. Experimental analysis for enhancement of heat transfer in two pass solar air heater duct by using square rib in discrete geometry. International Research Journal of Engineering and Technology, 03(06):1839–1846, 2016.
[14] S. Alfarawi, S A. Abdel-Moneim, and A. Bodalal. Experimental investigations of heat transfer enhancement from rectangular duct roughened by hybrid ribs. International Journal of Thermal Sciences, 118:123–138, 2017. doi: 10.1016/j.ijthermalsci.2017.04.017.
[15] G. Tanda. Heat transfer in rectangular channels with transverse and V-shaped broken ribs. International Journal of Heat and Mass Transfer, 47(2):229–243, 2004. doi: 10.1016/S0017-9310(03)00414-9.
[16] V. Kesharwani and R. Vishwakarma. Numerical investigation of heat transfer and fluid flow characteristics of square type tabulator roughness solar air heater. International Journal of Mechanical and Industrial Technology, 3(2):109–116, 2016.
[17] A. Kumar and M.-H. Kim. Thermohydraulic performance of rectangular ducts with different multiple V-rib roughness shapes: A comprehensive review and comparative study. Renewable and Sustainable Energy Reviews, 54:635–652, 2016. doi: 10.1016/j.rser.2015.10.030.
[18] D. Jin, J. Zuo, S. Quan, S. Xu, and H. Gao. Thermohydraulic performance of solar air heater with staggered multiple V-shaped ribs on the absorber plate. Energy, 127:68–77, 2017. doi: 10.1016/j.energy.2017.03.101.
[19] V.S. Bisht, A.K. Patil, and A. Gupta. Review and performance evaluation of roughened solar air heaters. Renewable and Sustainable Energy Reviews, 81(1):954–977, 2018. doi: 10.1016/j.rser.2017.08.036.
[20] A. Kumar and M.-H. Kim. Effect of roughness width ratios in discrete multi V-rib with staggered rib roughness on overall thermal performance of solar air channel. Solar Energy, 119:399–414, 2015. doi: 10.1016/j.solener.2015.06.030.
[21] A.S. Yadav and J. L. Bhagoria. Modeling and simulation of turbulent flows through a solar air heater having square-sectioned transverse rib roughness on the absorber plate. The Scientific World Journal, 2013:ID827131, 2013. doi: 10.1155/2013/827131.
[22] S. Acharya, T. Myrum, X. Qiu, and S. Sinha. Developing and periodically developed flow, temperature and heat transfer in a ribbed duct. International Journal of Heat and Mass Transfer, 40(2):461–479, 1997. doi: 10.1016/0017-9310(96)00033-6.
[23] P.R. Chandra, C.R. Alexander, and J. C. Han. Heat transfer and friction behaviors in rectangular channels with varying number of ribbed walls. International Journal of Heat and Mass Transfer, 46(3):481–495, 2003. doi: 10.1016/S0017-9310(02)00297-1.
[24] S.A. Abdel-Moneim, E.F. Atwan, and A.R. El-Shamy. Heat transfer and flow friction in a rectangular duct with repeated multiple V-ribs mounted on the bottom wall. In Proceedings of the 12th International Mechanical Power Engineering Conference (IMPEC12), pages 11–25, 2001.
[25] A. Gupta, V. SriHarsha, S.V. Prabhu, and R.P. Vedula. Local heat transfer distribution in a square channel with 90° continuous, 90° saw tooth profiled and 60° broken ribs. Experimental Thermal and Fluid Science, 32(4):997–1010, 2008. doi: 10.1016/j.expthermflusci.2007.11.015.
[26] W. Siddique, T.H. Fransson, and L.A. El-Gabry. Improved design of internally cooled trailing edge at engine similar conditions: A conjugate heat transfer problem. In Proceedings of the ASME Turbo Expo 2012: Turbine Technical Conference and Exposition. Volume 4: Heat Transfer, Parts A and B, pages 1357-1372. Copenhagen, Denmark. June 11–15, 2012. doi: 10.1115/GT2012-68557.
[27] J.C. Han, Y.M. Zhang, and C.P. Lee. Augmented heat transfer in square channels with parallel, crossed, and V-shaped angled ribs. Journal of Heat Transfer, 113(3):590–596, 1991. doi: 10.1115/1.2910606.
[28] B. Sundén and T. Sköldheden. Heat transfer and pressure drop in a new type of corrugated channels. International Communications in Heat and Mass Transfer, 12(5):559–566, 1985. doi: 10.1016/0735-1933(85)90079-X.
[29] T. Salameh and B. Sunden. An experimental study of heat transfer and pressure drop on the bend surface of a U-duct. In Proceedings of the ASME Turbo Expo 2010: Power for Land, Sea, and Air. Volume 4: Heat Transfer, Parts A and B, pages 13-21. Glasgow, UK. June 14–18, 2010. doi: 10.1115/GT2010-22139.
[30] T. Salameh and B. Sunden. Effects of ribs on internal blade-tip cooling. In Proceedings of the ASME 2011 Turbo Expo: Turbine Technical Conference and Exposition. Volume 5: Heat Transfer, Parts A and B, pages 1033-1041. Vancouver, British Columbia, Canada. June 6–10, 2011. doi: 10.1115/GT2011-45118.
[31] T. Salameh and B. Sunden. A numerical investigation of heat transfer in a smooth bend part of a U-duct. International Journal of Numerical Methods for Heat & Fluid Flow, 24(1):137–147, 2014. doi: 10.1108/HFF-03-2012-0066.
[32] T. Salameh and B. Sunden. Numerical investigation of convective heat transfer and pressure drop for ribbed surfaces in the bend part of a U-duct. In Proceedings of the ASME 2012 International Mechanical Engineering Congress and Exposition. Volume 7: Fluids and Heat Transfer, Parts A, B, C, and D, pages 1909-1916. Houston, Texas, USA. November 9–15, 2012. doi: 10.1115/IMECE2012-85621.
[33] L. Wang, T. Salameh, and B. Sunden. An experimental study of heat transfer on a smooth U-bend channel surface. In Proceedings of the ASME 2012 International Mechanical Engineering Congress and Exposition. Volume 7: Fluids and Heat Transfer, Parts A, B, C, and D, pages 1667-1674. Houston, Texas, USA. November 9–15, 2012. doi: 10.1115/IMECE2012-87295.
[34] A. Layek, J.S. Saini, and S.C. Solanki. Heat transfer and friction characteristics for artificially roughened ducts with compound turbulators. International Journal of Heat and Mass Transfer, 50(23-24):4845–4854, 2007. doi: 10.1016/j.ijheatmasstransfer.2007.02.042.
[35] E.A.M. Elshafei, M.M. Awad, E. El-Negiry, and A.G. Ali. Heat transfer and pressure drop in corrugated channels. Energy, 35(1):101–110, 2010. doi: 10.1016/j.energy.2009.08.031.
[36] G. Xia, D. Ma, Y. Zhai, Y. Li, R. Liu, and M. Du. Experimental and numerical study of fluid flow and heat transfer characteristics in microchannel heat sink with complex structure. Energy Conversion and Management, 105:848–857, 2015. doi: 10.1016/j.enconman.2015.08.042.
[37] Z. Wan, Q. Lin, X. Wang, and Y. Tang. Flow characteristics and heat transfer performance of half-corrugated microchannels. Applied Thermal Engineering, 123:1140–1151, 2017. doi: 10.1016/j.applthermaleng.2017.05.176.
[38] N. Tokgoz, M.M. Aksoy, and B. Sahin. Investigation of flow characteristics and heat transfer enhancement of corrugated duct geometries. Applied Thermal Engineering, 118:518–530, 2017. doi: 10.1016/j.applthermaleng.2017.03.013.
[39] W. Gao, W. Lin, T. Liu, and C. Xia. Analytical and experimental studies on the thermal performance of cross-corrugated and flat-plate solar air heaters. Applied Energy, 84(4):425–441, 2007. doi: 10.1016/j.apenergy.2006.02.005.
[40] T.A. Yassen, N.D. Mokhlif, and M.A. Eleiwi. Performance investigation of an integrated solar water heater with corrugated absorber surface for domestic use. Renewable Energy, vol. 138:852–860, 2019. doi: 10.1016/j.renene.2019.01.114.
[41] K. Tyagi. Detailed Experimental Measurements of Heat Transfer Augmentation in Internal Channels Using a Thermochromic Liquid Crystal Technique. Master Thesis, Virginia Polytechnic Institute and State University, Blacksburg, Virginia, USA, 2015.
[42] Z. Brodnianska. Experimental investigation of convective heat transfer between corrugated heated surfaces of rectangular channel. Heat Mass Transfer, 55:3151–3164, 2019. doi: 10.1007/s00231-019-02649-3.
[43] M. Khoshvaght-Aliabadi and F. Nozan. Water cooled corrugated minichannel heat sink for electronic devices: Effect of corrugation shape. International Communications in Heat and Mass Transfer, 76:188–196, 2016. doi: 10.1016/j.icheatmasstransfer.2016.05.021.
[44] M.S. Manjunath, K.V. Karanth, and N.Y. Sharma. Numerical investigation on heat transfer enhancement of solar air heater using sinusoidal corrugations on absorber plate. International Journal of Mechanical Sciences, 138-139:219–228, 2018. doi: 10.1016/j.ijmecsci.2018.01.037.
[45] C.-O. Olsson and B. Sunden. Thermal and hydraulic performance of a rectangular duct with multiple V-shaped ribs. Journal of Heat Transfer, 120(4):1072–1077, 1998. doi: 10.1115/1.2825892.
[46] P. Naphon. Heat transfer characteristics and pressure drop in channel with V corrugated upper and lower plates. Energy Conversion and Management, 48(5):1516–1524, 2007. doi: 10.1016/j.enconman.2006.11.020.
[47] C. Zimmerer, P. Gschwind, G. Gaiser, and V. Kottke. Comparison of heat and mass transfer in different heat exchanger geometries with corrugated walls. Experimental Thermal and Fluid Science, 26(2-4):269–273, 2002. doi: 10.1016/S0894-1777(02)00136-X.
[48] H. Pehlivan, I. Taymaz, and Y. İslamoğlu. Experimental study of forced convective heat transfer in a different arranged corrugated channel. International Communications in Heat and Mass Transfer, 46:106–111, 2013. doi: 10.1016/j.icheatmasstransfer.2013.05.016.
[49] K. Sarraf, S. Launay, and L. Tadrist. Complex 3D-flow analysis and corrugation angle effect in plate heat exchangers. International Journal of Thermal Sciences, 94:126–138, 2015. doi: 10.1016/j.ijthermalsci.2015.03.002.
[50] J.E. O’Brien and E. M. Sparrow. Corrugated-duct heat transfer, pressure drop, and flow visualization. Journal of Heat Transfer, 104(3):410–416, 1982. doi: 10.1115/1.3245108.
[51] Y. Islamoglu and C. Parmaksizoglu. The effect of channel height on the enhanced heat transfer characteristics in a corrugated heat exchanger channel. Applied Thermal Engineering, 23(8):979–987, 2003. doi: 10.1016/S1359-4311(03)00029-2.
[52] A.H.H. Ali and Y. Hanaoka. Experimental study on laminar flow forced-convection in a channel with upper V-corrugated plate heated by radiation. International Journal of Heat and Mass Transfer, 45(10):2107–2117, 2002. doi: 10.1016/S0017-9310(01)00309-X.
[53] Y. Qin, X. Guan, Z. Dun, and H. Liu. Numerical simulation on fluid flow and heat transfer in a corrugated plate air preheater. Journal of Chinese Society of Power Engineering, 35:213–218, 2015.
[54] M.A. Mehrabian and R. Poulter. Hydrodynamics and thermal characteristics of corrugated channels: computational approach. Applied Mathematical Modelling, 24(5):343–364, 2000. 10.1016/S0307-904X(99)00039-6.
[55] B.N. Prasad and J.S. Saini. Effect of artificial roughness on heat transfer and friction factor in a solar air heater. Solar Energy, 41(6): 555–560, 1988. 10.1016/0038-092X(88)90058-8.
[56] S. Karsli. Performance analysis of new-design solar air collectors for drying applications. Renewable Energy, 32(10):1645–1660, 2007. 10.1016/j.renene.2006.08.005.
[57] H. Lu, B. Ren, Z. Pu, J. Si, F. Ren, and Y. Du. Simplified calculation of energy efficiency index for plate heat exchanger. IOP Conference Series: Earth and Environment Science, 552:12017, 2020. doi: 10.1088/1755-1315/552/1/012017.
[58] V.S. Hans, R P. Saini, and J.S. Saini. Heat transfer and friction factor correlations for a solar air heater duct roughened artificially with multiple V-ribs. Solar Energy, 84(6):898–911, 2010. doi: 10.1016/j.solener.2010.02.004.
[59] S.K. Saini and R.P. Saini. Development of correlations for Nusselt number and friction factor for solar air heater with roughened duct having arc-shaped wire as artificial roughness. Solar Energy, 82(12)1118–1130, 2008. doi: 10.1016/j.solener.2008.05.010.
[60] A. Raheem, W. Siddique, Z.H. Farooqui, T. Salameh, I. Haq, K. Waheed, and K. Qureshi. Performance evaluation of adding helical-screw tape inserts in parabolic solar trough collectors as a source of cleaner energy production. Journal of Cleaner Production, 297:126628, 2021. 10.1016/j.jclepro.2021.126628.
[61] W.H. Hager. Blasius: A life in research and education. Experiments in Fluids, 34(5)566–571, 2003. doi: 10.1007/s00348-002-0582-9.
[62] C.F. Colebrook, T. Blench, H. Chatley, E.H. Essex, J.R.Finniecome, G. Lacey, J. Williamson, and G.G. Macdonald. Turbulent flow in pipes, with particular reference to the transition region between the smooth and rough pipe laws. Journal of the Institution of Civil Engineers, 11(4)133–156, 1939. doi: 10.1680/ijoti.1939.14509.
[63] D. Brkić. Solution of the implicit Colebrook equation for flow friction using Excel. Spreadsheets in Education, 10(2):Art.2, 2017.
[64] T.L. Bergman, A.S. Lavine, F.P. Incropera, and D.P. DeWitt. Fundamentals of Heat and Mass Transfer. John Wiley & Sons, 2011.
[65] H. Hassan, S. Abo-Elfadl, and M.F. El-Dosoky. An experimental investigation of the performance of new design of solar air heater (tubular). Renewable Energy, 151:1055–1066, 2020. doi: 10.1016/j.renene.2019.11.112.
[66] R.J. Moffat. Describing the uncertainties in experimental results. Experimental Thermal and Fluid Science, 1(1):3–17, 1988. doi: 10.1016/0894-1777(88)90043-X.
Go to article

Authors and Affiliations

Waseem Siddique
1
Aneeq Raheem
1
Muhammad Aqeel
2
Sualeh Qayyum
2
Tareq Salamen
3
Khalid Waheed
2
Kamran Qureshi
1

  1. Department of Mechanical Engineering, Pakistan Institute of Engineering & Applied Sciences, Nilore, Islamabad, Pakistan
  2. Department of Nuclear Engineering, Pakistan Institute of Engineering & Applied Sciences, Nilore, Islamabad, Pakistan
  3. Sustainable and Renewable Energy Engineering Department, University of Sharjah, United Arab Emirates
Download PDF Download RIS Download Bibtex

Abstract

The article describes how different friction coefficients under certain cutting conditions and parameters affect the formation of the stress-strain and thermal states of the product when titanium alloy machining. A new research methodology is used for the study. Firstly, in the initial data for simulation, each time a different declared coefficient of friction is proposed, and every such task of the cutting process modelling is solved for various cutting parameters. The second stage analyzes how these coefficients influence the stress-strain and thermodynamic state of the workpiece and tool during cutting, as well as the tool wear dynamics. In the third stage of the study, ways for ensuring these analytically-grounded tribological cutting conditions are proposed. The analysis of different wear criteria in the simulation models of titanium alloys cutting is carried out. Experimental studies confirm simulation results.
Go to article

Bibliography

[1] M. Motyka, W. Ziaja, and J. Sieniawski. Titanium Alloys – Novel Aspects of Their Manufacturing and Processing. IntechOpen, London, 2019.
[2] A.Í.S. Antonialli, A.E. Diniz, and R. Pederiva. Vibration analysis of cutting force in titanium alloy milling. International Journal of Machine Tools and Manufacture, 50(1):65–74, 2010. doi: 10.1016/j.ijmachtools.2009.09.006.
[3] Q. Yang, Z. Liu, Z. Shi, and B. Wang. Analytical modeling of adiabatic shear band spacing for serrated chip in high-speed machining. The International Journal of Advanced Manufacturing Technology, 71:1901–1908, 2014. doi: 10.1007/s00170-014-5633-x.
[4] V.P. Astakhov. Metal Cutting Mechanics. CRC Press, Boca Raton, 1998.
[5] V.P. Astakhov and J.C. Outeiro. Metal cutting mechanics, finite element modelling. In J.P. Davim (ed), Machining. Fundamentals and Recent Advances, chapter 1, pages 1–27. Springer-Verlag London, 2008. doi: 10.1007/978-1-84800-213-5_1.
[6] F. Novikov and E. Benin. Determination of conditions ensuring cost price reduction of machinery. Economics of Development, 3(63):69–74, 2012.
[7] J.P. Davim (ed.). Machining of Titanium Alloys. Springer-Verlag Berlin, Heidelberg, 2014.
[8] F. Klocke, W. König, and K. Gerschwiler. Advanced machining of titanium- and nickel-based alloys. In: E. Kuljanic (ed.) Advanced Manufacturing Systems and Technology. CISM Courses and Lectures, vol. 372, chapter 1, pages 7–42. Springer, Vienna, 1996. doi: 10.1007/978-3-7091-2678-3_2.
[9] V.P. Astakhov. Tribology of Metal Cutting. Elsevier, London, 2006.
[10] J.P. Davim (ed.). Tribology in Manufacturing Technology. Springer, Berlin, Heidelberg, 2013. doi: 10.1007/978-3-642-31683-8.
[11] S.G. Larsson. The cutting process – A tribological nightmare. Technical Report, Seco Corp., Bern, Switzerland, December 2014. http://cbnexpert.blogspot.com/2014).
[12] P.L.B. Oxley. Mechanics of Machining: An Analytical Approach to Assessing Machinability, John Wiley & Sons, New York, 1989.
[13] A. Moufki, D. Dudzinski, and G. Le Coz. Prediction of cutting forces from an analytical model of oblique cutting, application to peripheral milling of Ti-6Al-4V alloy. The International Journal of Advanced Manufacturing Technology, 81:615–626, 2015. doi: 10.1007/s00170-015-7018-1.
[14] M.J. Bermingham, S. Palanisamy, and M.S. Dargusch. Understanding the tool wear mechanism during thermally assisted machining Ti-6Al-4V. International Journal of Machine Tools and Manufacture, 62:76–87, 2012, doi: 10.1016/j.ijmachtools.2012.07.001.
[15] O.C. Zienkiewicz, R.L. Taylor, and D.D. Fox. The Finite Element Method for Solid and Structural Mechanics. 7th edition. Butterworth-Heinemann, Oxford, 2014.
[16] F. Klocke. Manufacturing Processes 1. Cutting. Springer-Verlag, Berlin Heidelberg, 2011. doi: 10.1007/978-3-642-11979-8.
[17] D.A. Stephenson and J.S. Agapiou. Metal Cutting Theory and Practice. 3rd edition. CRC Press, Boca Raton, 2016.
[18] H. Shi. Metal Cutting Theory. New Perspectives and New Approaches. Springer, 2018.
[19] V. Stupnytskyy and I. Hrytsay. Simulation study of cutting-induced residual stress. In: Advances in Design, Simulation and Manufacturing II. DSMIE 2019. Lecture Notes in Mechanical Engineering: 341-350, 2020. doi: 10.1007/978-3-030-22365-6_34.
[20] N.G. Burago and V.N. Kukudzhanov. About damage and localization of strains. Problems of Strength and Plasticity, 63:40–48, 2001. doi: 10.13140/RG.2.1.4749.9923.
[21] P.Ståhle, A. Spagnoli, and M. Terzano. On the fracture processes of cutting. Procedia Structural Integrity, 3:468–476, 2017. doi: 10.1016/j.prostr.2017.04.063.
[22] E. Gdoutos. Fracture Mechanics Criteria and Applications. Springer Netherlands, 1990.
[23] S.L.M.R. Filho, R.B.D. Pereira, C.H. Lauro, and L.C. Brandao. Investigation and modelling of the cutting forces in turning process of the Ti-6Al-4V and Ti-6Al-7Nb titanium alloys. The International Journal of Advanced Manufacturing Technology, 101:2191–2203, 2019. doi: 10.1007/s00170-018-3110-7.
[24] A. Pramanik and G. Littlefair. Wire EDM mechanism of MMCs with the variation of reinforced particle size. Materials and Manufacturing Processes, 31(13):1700–1708, 2016. doi: 10.1080/10426914.2015.1117621.
[25] V. Stupnytskyy and I. Hrytsay. Comprehensive analysis of the product’s operational properties formation considering machining technology. Archive of Mechanical Engineering, 67(2):149–167, 2020. doi: 10.24425/ame.2020.131688.
[26] T. Obikawa and E. Usui. Computational Mmachining of titanium alloy—finite element modeling and a few results. Journal of Manufacturing Science and Engineering, 118(2):208–215, 1996. doi: 10.1115/1.2831013.
[27} M. Rahman, Z.-G. Wang, and Y.-S. Wong. A review on high-speed machining of titanium alloys. JSME International Journal Series C Mechanical Systems, Machine Elements and Manufacturing, 49(1):11-20, 2006. doi: 10.1299/jsmec.49.11.
[28] G. Chen, C. Ren, X. Yang, X. Jin, and T. Guo. Finite element simulation of high-speed machining of titanium alloy (Ti–6Al–4V) based on ductile failure model. The International Journal of Advanced Manufacturing Technology, 56:1027–1038, 2011. doi: 10.1007/s00170-011-3233-6.
[29] T. Tamizharasan and N. Senthilkumar. Optimization of cutting insert geometry using DEFORM-3D: numerical simulation and experimental validation. International Journal of Simulation Modelling, 11(2):65–76, 2012. doi: 10.2507/IJSIMM11(2)1.200.
[30] E. Usui, T. Shirakashi, and T.Kitagawa. Analytical prediction of cutting tool wear. Wear, 100 (1-3):129–151, 1984. doi: 10.1016/0043-1648(84)90010-3.
[31] J.F. Archard. Contact and rubbing of flat surfaces. Journal of Applied Physics, 24:981–988, 1953. doi: 10.1063/1.1721448.
[32] A.G. Suslov. To the problem of friction and wear of machinery. Journal of Friction and Wear, 5:801-807, 1990.
[33] P.J. Blau. Amontons’ laws of friction. In: Q.J. Wang, Y.W. Chung. (eds) Encyclopedia of Tribology. Springer, Boston, 2013. doi: 10.1007/978-0-387-92897-5_166.
[34] P.D. Hartung, B.M. Kramer, and B.F. von Turkovich. Tool wear in titanium machining. CIRP Annals, 31(1):75–80, 1982. doi: 10.1016/S0007-8506(07)63272-7.
[35] A.G. Kisel’, D.S. Makashin, K.V. Averkov, and A.A. Razhkovskii. Effectiveness and physical characteristics of machining fluid. Russian Engineering Research, 38:508–512, 2018. doi: 10.3103/S1068798X18070092.
[36] D.V. Evdokimov and M.A. Oleynik. Research of the friction coefficient of titanium and instrumental alloys. Dry and boundary friction. News of Samara Scientific Center of the Russian Academy of Sciences, 22(1):43-46, 2020. doi: 10.37313/1990-5378-2020-22-1-43-46 (in Russian).
[37] Y. Su, L. Li, G. Wang, and X. Zhong. Cutting mechanism and performance of high-speed machining of a titanium alloy using a super-hard textured tool. Journal of Manufacturing Processes, 34(A):706-712, 2018. 10.1016/j.jmapro.2018.07.004.
[38] R.B. Da Silva, J.M. Vieira, R.N. Cardoso, H.C. Carvalho, E.S. Costa, A.R. Machado and R.F. De Ávila. Tool wear analysis in milling of medium carbon steel with coated cemented carbide inserts using different machining lubrication/cooling systems. Wear, 271(9-10):2459–2465, 2011. 10.1016/j.wear.2010.12.046.
[39] S.Y. Hong, I. Markus, and W.-C. Jeong. New cooling approach and tool life improvement in cryogenic machining of titanium alloy Ti-6Al-4V. International Journal of Machine Tools and Manufacture, 41(15):2245–2260, 2001. doi: 10.1016/S0890-6955(01)00041-4.
[40] V. Stupnytskyy and I. Hrytsay. Computer-aided conception for planning and researching of the functional-oriented manufacturing process. In: Tonkonogyi V. et al. (eds): Advanced Manufacturing Processes. InterPartner 2019. Lecture Notes in Mechanical Engineering, pages 309–320. Springer, Cham, 2020. doi: 10.1007/978-3-030-40724-7_32.
Go to article

Authors and Affiliations

Vadym Stupnytskyy
1
ORCID: ORCID
Xianning She
1
ORCID: ORCID

  1. Lviv Polytechnic National University, Lviv, Ukraine

Instructions for authors

About the Journal
Archive of Mechanical Engineering is an international journal publishing works of wide significance, originality and relevance in most branches of mechanical engineering. The journal is peer-reviewed and is published both in electronic and printed form. Archive of Mechanical Engineering publishes original papers which have not been previously published in other journal, and are not being prepared for publication elsewhere. The publisher will not be held legally responsible should there be any claims for compensation. The journal accepts papers in English.

Archive of Mechanical Engineering is an Open Access journal. The journal does not have article processing charges (APCs) nor article submission charges.

Outline of procedures
  • To ensure that high scientific standards are met, the editorial office of Archive of Mechanical Engineering implements anti-ghost writing and guest authorship policy. Ghostwriting and guest authorship are indication of scientific dishonesty and all cases will be exposed: editorial office will inform adequate institutions (employers, scientific societies, scientific editors associations, etc.).
  • To maintain high quality of published papers, the editorial office of Archive of Mechanical Engineering applies reviewing procedure. Each manuscript undergoes crosscheck plagiarism screening. Each manuscript is reviewed by at least two independent reviewers.
  • Before publication of the paper, authors are obliged to send scanned copies of the signed originals of the declaration concerning ghostwriting, guest authorship and authors contribution and of the Open Access license.
Submission of manuscripts

The manuscripts must be written in one of the following formats:
  • TeX, LaTeX, AMSTeX, AMSLaTeX (recommended),
  • MS Word, either as standard DOCUMENT (.doc, .docx) or RICH TEXT FORMAT (.rtf).
All submissions to the AME should be made electronically via Editorial System – an online submission and peer review system at https://www.editorialsystem.com/ame. First-time users must create an Author’s account to obtain a user ID and password required to enter the system. All manuscripts receive individual identification codes that should be used in any correspondence with regard to the publication process. For the authors already registered in Editorial System it is enough to enter their username and password to log in as an author. The corresponding author should be identified while submitting a paper – personal e-mail address and postal address of the corresponding author are required. Please note that the manuscript should be prepared using our LaTeX or Word template and uploaded as a PDF file.

If you experience difficulties with the manuscript submission website, please contact the Assistant to the Editor of the AME (ame.eo@meil.pw.edu.pl).

All authors of the manuscript are responsible for its content; they must have agreed to its publication and have given the corresponding author the authority to act on their behalf in all matters pertaining to publication. The corresponding author is responsible for informing the co-authors of the manuscript status throughout the submission, review, and production process.

Length and arrangement

Papers (including tables and figures) should not exceed in length 25 pages of size 12.6 cm x 19.5 cm (printing area) with a font size of 11 pt. For manuscript preparation, the Authors should use the templates for Word or LaTeX available at the journal webpage. Please notice that the final layout of the article will be prepared by the journal's technical staff in LaTeX. Articles should be organized into the following sections:
  • List of keywords (separated by commas),
  • Full Name(s) of Author(s), Affiliation(s), Corresponding Author e-mail address,
  • Title,
  • Abstract,
  • Main text,
  • Appendix,
  • Acknowledgments (if applicable),
  • References.
Affiliations should include department, university, city and country. ORCID identifiers of all Authors should be added.
We suggest the title should be as short as possible but still informative.

An abstract should accompany every article. It should be a brief summary of significant results of the paper and give concise information about the content of the core idea of the paper. It should be informative and not only present the general scope of the paper, but also indicate the main results and conclusions. An abstract should not exceed 200 words.

Please follow the general rules for writing the main text of the paper:
  • use simple and declarative sentences, avoid long sentences, in which the meaning may be lost by complicated construction,
  • divide the main text into sections and subsections (if needed the subsections may be divided into paragraphs),
  • be concise, avoid idle words,
  • make your argumentation complete; use commonly understood terms; define all nonstandard symbols and abbreviations when you introduce them;
  • explain all acronyms and abbreviations when they first appear in the text;
  • use all units consistently throughout the article;
  • be self-critical as you review your drafts.
The authors are advised to use the SI system of units.

Artwork/Equations/Tables

You may use line diagrams and photographs to illustrate theses from your text. The figures should be clear, easy to read and of good quality (300 dpi). The figures are preferred in a vector format (bitmap formats are acceptable, but not recommended). The size of the figures should be adequate to their contents. Use 8-9pt font size of the text within the figures.

You should use tables only to improve conciseness or where the information cannot be given satisfactorily in other ways. Tables should be numbered consecutively and referred to within the text by numbers. Each table should have an explanatory caption which should be as concise as possible. The figures and tables should be inserted in the text file, where they are mentioned.

Displayed equations should be numbered consecutively using Arabic numbers in parentheses. They should be centered, leaving a small space above and below to separate it from the surrounding text.

Footnotes/Endnotes/Acknowledgements

We encourage authors to restrict the use of footnotes. Information concerning research grant support should appear in a separate Acknowledgements section at the end of the paper. Acknowledgements of the assistance of colleagues or similar notes of appreciation should also appear in the Acknowledgements section.

References
References should be numbered and listed in the order that they appear in the text. References indicated by numerals in square brackets should complete the paper in the following style:

Books:
[1] R.O. Author. Title of the Book in Italics. Publisher, City, 2018.

Articles in Journals:
[2] D.F. Author, B.D. Second Author, and P.C. Third Author. Title of the article. Full Name of the Journal in Italics, 52(4):89–96, 2017. doi: 1234565/3554. (where means: 52 – volume; 4 – number or issue; 89–96 – pages, and 1234565/3554 – doi number (if exists).)

Theses:
[3] W. Author. Title of the thesis. Ph.D. Thesis, University, City, Country, 2010.

Conference Proceedings:
[4] H. Author. Title of the paper. In Proc. Conference Name in Italics, pages 001–005, Conference Place, 10-15 Jan. 2015. doi: 98765432/7654vd.

English language

Archive of Mechanical Engineering is published in English. Make sure that your manuscript is clearly and grammatically written. The content should be understandable and should not cause any confusion to the readers, including the reviewers. After accepting the manuscript for a publication in the AME, we offer a free language check service, for correcting small language mistakes.

Submission of Revised Articles

When revision of a manuscript is requested, authors are expected to deliver the revised version of the manuscript as soon as possible. The manuscript should be uploaded directly to the Editorial System as an answer to the Editor's decision, and not as a new manuscript. If it is the 1st revision, the authors are expected to return revised manuscript within 60 days; if it is the 2nd revision, the authors are expected to return revised manuscript within 14 days. Additional time for resubmission must be requested in advance. If the above mentioned deadlines are not met, the manuscript may be treated as a new submission.

Outline of the Production Process

Once an article has been accepted for publication, the manuscript is transferred into our production system to be language-edited and formatted. Language/technical editors reserve the privilege of editing manuscripts to conform with the stylistic conventions of the journal. Once the article has been typeset, PDF proofs are generated so that authors can approve all editing and layout.

Proofreading

Proofreading should be carried out once a final draft has been produced. Since the proofreading stage is the last opportunity to correct the article to be published, the authors are requested to make every effort to check for errors in their proofs before the paper is posted online. Authors may be asked to address remarks and queries from the language and/or technical editors. Queries are written only to request necessary information or clarification of an unclear passage. Please note that language/technical editors do not query at every instance where a change has been made. It is the author's responsibility to read the entire text, tables, and figure legends, not just items queried. Major alterations made will always be submitted to the authors for approval. The corresponding author receives e-mail notification when a PDF is available and should return the comments within 3 days of receipt. Comments must be uploaded to Editorial System.

Reviewers


The Editorial Board of the Archive of Mechanical Engineering (AME) sincerely expresses gratitude to the following individuals who devoted their time to review papers submitted to the journal. Particularly, we express our gratitude to those who reviewed papers several times.

List of reviewers in 2023

Sara I. ABDELSALAM – University of California Riverside, United States
M. ARUNA – Liwa College of Technology, United Arab Emirates
Krzysztof BADYDA – Warsaw University of Technology, Poland
Nathalie BÄSCHLIN – Kunstmuseum Bern, Germany
Joanna BIJAK – Silesian University of Technology, Gliwice, Poland
Tomas BODNAR – The Czech Academy of Sciences, Prague, Czech Republic
Dariusz BUTRYMOWICZ – Białystok University of Technology, Poland
Suleyman CAGAN – Mechanical Engineering, Mersin University, Turkey
Claudia CASAPULLA – University of Naples Federico II, Italy
Peng CHEN – Northwestern Polytechnical University, Xi’an, China
Yao CHENG – Southwest Jiaotong University, Chengdu, China
Jan de JONG – University of Twente, Netherlands
Mariusz DEJA – Gdańsk University of Technology, Poland
Jerzy EJSMONT – Gdańsk University of Technology, Poland
İsmail ESEN – Karabuk University, Turkey
Pedro Javier GAMEZ-MONTERO – Universitat Politecnica de Catalunya, Spain
Aman GARG – National Institute of Technology, Kurukshetra, India
Michał HAĆ – Warsaw University of Technology, Poland
Satoshi ISHIKAWA – Kyushu University, Japan
Jacek JACKIEWICZ – Kazimierz Wielki University, Bydgoszcz, Poland
Krzysztof JAMROZIAK – Wrocław University of Technology, Poland
Hong-Lae JANG – Changwon National University, Korea (South)
Łukasz JANKOWSKI – Institute of Fluid-Flow Machinery, PAS, Gdansk, Poland
Albizuri JOSEBA – University of the Basque Country, Spain
Łukasz KAPUSTA – Warsaw University of Technology, Poland
Dariusz KARDAŚ – Institute of Fluid-Flow Machinery, PAS, Gdansk, Poland
Panagiotis KARMIRIS-OBRATAŃSKI – AGH University of Science and Technology, Cracow, Poland
Sivakumar KARTHIKEYAN – SRM Nagar
Tarek KHELFA – Hunan University of Humanities Science and Technology, China
Sven-Joachim KIMMERLE – Universität der Bundeswehr München, Germany
Thomas KLETSCHKOWSKI – HAW Hamburg, Germany
Piotr KLONOWICZ – Institute of Fluid-Flow Machinery, PAS, Gdansk, Poland
Vladis KOSSE – Queensland University of Technology, Australia
Mariusz KOSTRZEWSKI – Warsaw University of Technology, Poland
Maria KOTELKO – Lodz University of Technology, Poland
Michał KOWALIK – Warsaw University of Technology, Poland
Zbigniew KRZEMIANOWSKI – Institute of Fluid-Flow Machinery, Gdańsk, Poland
Slawomir KUBACKI – Warsaw University of Technology, Poland
Mieczysław KUCZMA – Poznan University of Technology, Poland
Waldemar KUCZYŃSKI – The Koszalin University of Technology, Poland
Rafał KUDELSKI – AGH University of Science and Technology, Cracow, Poland
Rajesh KUMAR – Sant Longowal Institute of Engineering and Technology, India
Mustafa KUNTOĞLU – Selcuk University, Turkey
Anna LEE – Pohang University of Science and Technology, South Korea, Korea (South)
Guolong LI – Chongqing University, China
Luxian LI – Xi'an Jiaotong University, China
Yingchao LI – Ludong University, Yantai, China
Xiaochuan LIN – Nanjing Tech University, China
Zhihong LIN – HuaQiao University, China
Yakun LIU – Massachusetts Institute of Technology, United States
Jinjun LU – Northwest University, Xiʼan, China
Paweł MACIĄG – Warsaw University of Technology, Poland
Paweł MALCZYK – Warsaw University of Technology, Poland
Emil MANOACH – Bulgarian Academy of Sciences, Sofia, Bulgaria
Mihaela MARIN – “Dunărea de Jos” University of Galati, Romania
Miloš MATEJIĆ – University of Kragujevac, Serbia
Krzysztof MIANOWSKI – Warsaw University of Technology, Poland
Tran MINH TU – Hanoi University of Civil Engineering, Viet Nam
Farhad Sadegh MOGHANLOU – University of Mohaghegh Ardabili, Ardabil, Iran
Mohsen MOTAMEDI – University of Isfahan, Iran
Adis MUMINOVIC – University of Sarajevo, Bosnia and Herzegovina
Mohamed NASR – National Research Centre, Giza, Egypt
Huu-That NGUYEN – Nha Trang University, Viet Nam
Tan-Luy NGUYEN – Ho Chi Minh City University of Technology, Viet Nam
Viorel PALEU – Gheorghe Asachi Technical University of Iasi, Romania
Nicolae PANC – Technical University of Cluj-Napoca, Romania
Marcin PĘKAL – Warsaw University of Technology, Poland
Van Vinh PHAM – Le Quy Don Technical University, Hanoi, Viet Nam
Vaclav PISTEK – Brno University of Technology, Czech Republic
Paweł PYRZANOWSKI – Warsaw University of Technology, Poland
Lei QIN – Beijing Information Science & Technology University, China
Milan RACKOV – University of Novi Sad, Serbia
Yuriy ROMASEVYCH – National University of Life and Environmental Sciences of Ukraine, Kiev, Ukraine
Artur RUSOWICZ – Warsaw University of Technology, Poland
Andrzej SACHAJDAK – Silesian University of Technology, Gliwice, Poland
Mirosław SEREDYŃSKI – Warsaw University of Technology, Poland
Maciej SUŁOWICZ – Cracow University of Technology, Poland
Biswajit SWAIN – National Institute of Technology, Rourkela, India
Tadeusz SZYMCZAK – Motor Transport Institute, Warsaw, Poland
Reza TAHERDANGKOO – Institute of Geotechnics, Freiberg, Germany
Rulong TAN – Chongqing University of Technology, China
Daniel TOBOŁA – Łukasiewicz Research Network - Cracow Institute of Technology, Poland
Milan TRIFUNOVIĆ – University of Niš, Serbia
Duong VU – Duy Tan University, Viet Nam
Shaoke WAN – Xi’an Jiaotong University, China
Dong WEI – Northwest A&F University, Yangling , China
Marek WOJTYRA – Warsaw University of Technology, Poland
Mateusz WRZOCHAL – Kielce University of Technology, Poland
Hugo YAÑEZ-BADILLO – TecNM: Tecnológico de Estudios Superiores de Tianguistenco, Mexico
Guichao YANG – Nanjing Tech University, China
Xiao YANG – Chongqing Technology and Business University, China
Yusuf Furkan YAPAN – Yildiz Technical University, Turkey
Luhe ZHANG – Chongqing University, China
Xiuli ZHANG – Shandong University of Technology, Zibo, China

List of reviewers in 2022
Isam Tareq ABDULLAH – Middle Technical University, Baghdad, Iraq
Ahmed AKBAR – University of Technology, Iraq
Nandalur AMER AHAMMAD – University of Tabuk, Saudi Arabia
Ali ARSHAD – Riga Technical University, Latvia
Ihsan A. BAQER – University of Technology, Iraq
Thomas BAR – Daimler AG, Stuttgart, Germany
Huang BIN – Zhejiang University, Zhoushan, China
Zbigniew BULIŃSKI – Silesian University of Technology, Poland
Onur ÇAVUSOGLU – Gazi University, Turkey
Ali J CHAMKHA – Duy Tan University, Da Nang , Vietnam
Dexiong CHEN – Putian University, China
Xiaoquan CHENG – Beihang University, Beijing, China
Piotr CYKLIS – Cracow University of Technology, Poland
Agnieszka DĄBSKA – Warsaw University of Technology, Poland
Raphael DEIMEL – Berlin University of Technology, Germany
Zhe DING – Wuhan University of Science and Technology, China
Anselmo DINIZ – University of Campinas, São Paulo, Brazil
Paweł FLASZYŃSKI – Institute of Fluid-Flow Machinery, Gdańsk, Poland
Jerzy FLOYRAN – University of Western Ontario, London, Canada
Xiuli FU – University of Jinan, China
Piotr FURMAŃSKI – Warsaw University of Technology, Poland
Artur GANCZARSKI – Cracow University of Technology, Poland
Ahmad Reza GHASEMI– University of Kashan, Iran
P.M. GOPAL – Anna University, Regional Campus Coimbatore, India
Michał GUMNIAK – Poznan University of Technology, Poland
Bali GUPTA – Jaypee University of Engineering and Technology, India
Dmitriy GVOZDYAKOV – Tomsk Polytechnic University, Russia
Jianyou HAN – University of Science and Technology, Beijing, China
Tomasz HANISZEWSKI – Silesian University of Technology, Poland
Juipin HUNG – National Chin-Yi University of Technology, Taichung, Taiwan
T. JAAGADEESHA – National Institute of Technology, Calicut, India
Jacek JACKIEWICZ – Kazimierz Wielki University, Bydgoszcz, Poland
JC JI – University of Technology, Sydney, Australia
Feng JIAO – Henan Polytechnic University, Jiaozuo, China
Daria JÓŹWIAK-NIEDŹWIEDZKA – Institute of Fundamental Technological Research, Warsaw, Poland
Rongjie KANG – Tianjin University, China
Dariusz KARDAŚ – Institute of Fluid-Flow Machinery, Gdansk, Poland
Leif KARI – KTH Royal Institute of Technology, Sweden
Daria KHANUKAEVA – Gubkin Russian State University of Oil and Gas, Russia
Sven-Joachim KIMMERLE – Universität der Bundeswehr München, Germany
Yeong-Jin KING – Universiti Tunku Abdul Rahman, Malaysia
Kaushal KISHORE – Tata Steel Limited, Jamshedpur, India
Nataliya KIZILOVA – Warsaw University of Technology, Poland
Adam KLIMANEK – Silesian University of Technology, Poland
Vladis KOSSE – Queensland University of Technology, Australia
Maria KOTEŁKO – Lodz University of Technology, Poland
Roman KRÓL – Kazimierz Pulaski University of Technology and Humanities in Radom, Poland
Krzysztof KUBRYŃSKI – Airforce Institute of Technology, Warsaw, Poland
Mieczysław KUCZMA – Poznan University of Technology, Poland
Paweł KWIATOŃ – Czestochowa University of Technology, Poland
Lihui Lang – Beihang University, China
Rafał LASKOWSKI – Warsaw University of Technology, Poland
Guolong Li – Chongqing University, China
Leo Gu LI – Guangzhou University, China
Pengnan LI – Hunan University of Science and Technology, China
Nan LIANG – University of Toronto, Mississauga, Canada
Michał LIBERA – Poznan University of Technology, Poland
Wen-Yi LIN – Hungkuo Delin University of Technology, Taiwan
Wojciech LIPINSKI – Austrialian National University, Canberra, Australia
Linas LITVINAS – Vilnius University, Lithuania
Paweł MACIĄG – Warsaw University of Technology, Poland
Krishna Prasad MADASU – National Institute of Technology Raipur, Chhattisgarh, India
Trent MAKI – Amino North America Corporation, Canada
Marco MANCINI – Institut für Energieverfahrenstechnik und Brennstofftechnik, Germany
Piotr MAREK – Warsaw University of Technology, Poland
Miloš MATEJIĆ – University of Kragujevac, Serbia
Phani Kumar MEDURI – VIT-AP University, Amaravati, India
Fei MENG – University of Shanghai for Science and Technology, China
Saleh MOBAYEN – University of Zanjan, Iran
Vedran MRZLJAK – Rijeka University, Croatia
Adis MUMINOVIC – University of Sarajevo, Bosnia and Herzegovina
Mohamed Fawzy NASR – National Research Centre, Giza, Egypt
Paweł OCŁOŃ – Cracow University of Technology, Poland
Yusuf Aytaç ONUR – Zonguldak Bulent Ecevit University, Turkey
Grzegorz ORZECHOWSKI – LUT University, Lappeenranta, Finland
Halil ÖZER – Yıldız Technical University, Turkey
Muthuswamy PADMAKUMAR – Technology Centre Kennametal India Ltd., Bangalore, India
Viorel PALEU – Gheorghe Asachi Technical University of Iasi, Romania
Andrzej PANAS – Warsaw Military Academy, Poland
Carmine Maria PAPPALARDO – University of Salerno, Italy
Paweł PARULSKI – Poznan University of Technology, Poland
Antonio PICCININNI – Politecnico di Bari, Italy
Janusz PIECHNA – Warsaw University of Technology, Poland
Vaclav PISTEK – Brno University of Technology, Czech Republic
Grzegorz PRZYBYŁA – Silesian University of Technology, Poland
Paweł PYRZANOWSKI – Warsaw University of Technology, Poland
K.P. RAJURKARB – University of Nebraska-Lincoln, United States
Michał REJDAK – Institute of Chemical Processing of Coal, Zabrze, Poland
Krzysztof ROGOWSKI – Warsaw University of Technology, Poland
Juan RUBIO – University of Minas Gerais, Belo Horizonte, Brazil
Artur RUSOWICZ – Warsaw University of Technology, Poland
Wagner Figueiredo SACCO – Universidade Federal Fluminense, Petropolis, Brazil
Andrzej SACHAJDAK – Silesian University of Technology, Poland
Bikash SARKAR – NIT Meghalaya, Shillong, India
Bozidar SARLER – University of Lubljana, Slovenia
Veerendra SINGH – TATA STEEL, India
Wieńczysław STALEWSKI – Institute of Aviation, Warsaw, Poland
Cyprian SUCHOCKI – Institute of Fundamental Technological Research, Warsaw, Poland
Maciej SUŁOWICZ – Cracov University of Technology, Poland
Wojciech SUMELKA – Poznan University of Technology, Poland
Tomasz SZOLC – Institute of Fundamental Technological Research, Warsaw, Poland
Oskar SZULC – Institute of Fluid-Flow Machinery, Gdansk, Poland
Rafał ŚWIERCZ – Warsaw University of Technology, Poland
Raquel TABOADA VAZQUEZ – University of Coruña, Spain
Halit TURKMEN – Istanbul Technical University, Turkey
Daniel UGURU-OKORIE – Federal University, Oye Ekiti, Nigeria
Alper UYSAL – Yildiz Technical University, Turkey
Yeqin WANG – Syndem LLC, United States
Xiaoqiong WEN – Dalian University of Technology, China
Szymon WOJCIECHOWSKI – Poznan University of Technology, Poland
Marek WOJTYRA – Warsaw University of Technology, Poland
Guenter WOZNIAK – Technische Universität Chemnitz, Germany
Guanlun WU – Shanghai Jiao Tong University, China
Xiangyu WU – University of California at Berkeley, United States
Guang XIA – Hefei University of Technology, China
Jiawei XIANG – Wenzhou University, China
Jinyang XU – Shanghai Jiao Tong University,China
Jianwei YANG – Beijing University of Civil Engineering and Architecture, China
Xiao YANG – Chongqing Technology and Business University, China
Oguzhan YILMAZ – Gazi University, Turkey
Aznifa Mahyam ZAHARUDIN – Universiti Teknologi MARA, Shah Alam, Malaysia
Zdzislaw ZATORSKI – Polish Naval Academy, Gdynia, Poland
S.H. ZHANG – Institute of Metal Research, Chinese Academy of Sciences, China
Yu ZHANG – Shenyang Jianzhu University, China
Shun-Peng ZHU – University of Electronic Science and Technology of China, Chengdu, China
Yongsheng ZHU – Xi’an Jiaotong University, China

List of reviewers of volume 68 (2021)
Ahmad ABDALLA – Huaiyin Institute of Technology, China
Sara ABDELSALAM – University of California, Riverside, United States
Muhammad Ilman Hakimi Chua ABDULLAH – Universiti Teknikal Malaysia Melaka, Malaysia
Hafiz Malik Naqash AFZAL – University of New South Wales, Sydney, Australia
Reza ANSARI – University of Guilan, Rasht, Iran
Jeewan C. ATWAL – Indian Institute of Technology Delhi, New Delhi, India
Hadi BABAEI – Islamic Azad University, Tehran, Iran
Sakthi BALAN – K. Ramakrishnan college of Engineering, Trichy, India
Leszek BARANOWSKI – Military University of Technology, Warsaw, Poland
Elias BRASSITOS – Lebanese American University, Byblos, Lebanon
Tadeusz BURCZYŃSKI – Institute of Fundamental Technological Research, Warsaw, Poland
Nguyen Duy CHINH – Hung Yen University of Technology and Education, Hung Yen, Vietnam
Dorota CHWIEDUK – Warsaw University of Technology, Poland
Adam CISZKIEWICZ – Cracow University of Technology, Poland
Meera CS – University of Petroleum and Energy Studies, Duhradun, India
Piotr CYKLIS – Cracow University of Technology, Poland
Abanti DATTA – Indian Institute of Engineering Science and Technology, Shibpur, India
Piotr DEUSZKIEWICZ – Warsaw University of Technology, Poland
Dinesh DHANDE – AISSMS College of Engineering, Pune, India
Sufen DONG – Dalian University of Technology, China
N. Godwin Raja EBENEZER – Loyola-ICAM College of Engineering and Technology, Chennai, India
Halina EGNER – Cracow University of Technology, Poland
Fehim FINDIK – Sakarya University of Applied Sciences, Turkey
Artur GANCZARSKI – Cracow University of Technology, Poland
Peng GAO – Northeastern University, Shenyang, China
Rafał GOŁĘBSKI – Czestochowa University of Technology, Poland
Andrzej GRZEBIELEC – Warsaw University of Technology, Poland
Ngoc San HA – Curtin University, Perth, Australia
Mehmet HASKUL – University of Sirnak, Turkey
Michal HATALA – Technical University of Košice, Slovak Republic
Dewey HODGES – Georgia Institute of Technology, Atlanta, United States
Hamed HONARI – Johns Hopkins University, Baltimore, United States
Olga IWASINSKA – Warsaw University of Technology, Poland
Emmanuelle JACQUET – University of Franche-Comté, Besançon, France
Maciej JAWORSKI – Warsaw University of Technology, Poland
Xiaoling JIN – Zhejiang University, Hangzhou, China
Halil Burak KAYBAL – Amasya University, Turkey
Vladis KOSSE – Queensland University of Technology, Brisbane, Australia
Krzysztof KUBRYŃSKI – Air Force Institute of Technology, Warsaw, Poland
Waldemar KUCZYŃSKI – Koszalin University of Technology, Poland
Igor KURYTNIK – State Higher School in Oswiecim, Poland
Daniel LESNIC – University of Leeds, United Kingdom
Witold LEWANDOWSKI – Gdańsk University of Technology, Poland
Guolu LI – Hebei University of Technology, Tianjin, China
Jun LI – Xi’an Jiaotong University, China
Baiquan LIN – China University of Mining and Technology, Xuzhou, China
Dawei LIU – Yanshan University, Qinhuangdao, China
Luis Norberto LÓPEZ DE LACALLE – University of the Basque Country, Bilbao, Spain
Ming LUO – Northwestern Polytechnical University, Xi’an, China
Xin MA – Shandong University, Jinan, China
Najmuldeen Yousif MAHMOOD – University of Technology, Baghdad, Iraq
Arun Kumar MAJUMDER – Indian Institute of Technology, Kharagpur, India
Paweł MALCZYK – Warsaw University of Technology, Poland
Miloš MATEJIĆ – University of Kragujevac, Serbia
Norkhairunnisa MAZLAN – Universiti Putra Malaysia, Serdang, Malaysia
Dariusz MAZURKIEWICZ – Lublin University of Technology, Poland
Florin MINGIREANU – Romanian Space Agency, Bucharest, Romania
Vladimir MITYUSHEV – Pedagogical University of Cracow, Poland
Adis MUMINOVIC – University of Sarajevo, Bosnia and Herzegovina
Baraka Olivier MUSHAGE – Université Libre des Pays des Grands Lacs, Goma, Congo (DRC)
Tomasz MUSZYŃSKI – Gdansk University of Technology, Poland
Mohamed NASR – National Research Centre, Giza, Egypt
Driss NEHARI – University of Ain Temouchent, Algeria
Oleksii NOSKO – Bialystok University of Technology, Poland
Grzegorz NOWAK – Silesian University of Technology, Gliwice, Poland
Iwona NOWAK – Silesian University of Technology, Gliwice, Poland
Samy ORABY – Pharos University in Alexandria, Egypt
Marcin PĘKAL – Warsaw University of Technology, Poland
Bo PENG – University of Huddersfield, United Kingdom
Janusz PIECHNA – Warsaw University of Technology, Poland
Maciej PIKULIŃSKI – Warsaw University of Technology, Poland
T.V.V.L.N. RAO – The LNM Institute of Information Technology, Jaipur, India
Andrzej RUSIN – Silesian University of Technology, Gliwice, Poland
Artur RUSOWICZ – Warsaw University of Technology, Poland
Benjamin SCHLEICH – Friedrich-Alexander-Universität Erlangen-Nürnberg, Germany
Jerzy SĘK – Lodz University of Technology, Poland
Reza SERAJIAN – University of California, Merced, USA
Artem SHAKLEIN – Udmurt Federal Research Center, Izhevsk, Russia
G.L. SHI – Guangxi University of Science and Technology, Liuzhou, China
Muhammad Faheem SIDDIQUI – Vrije University, Brussels, Belgium
Jarosław SMOCZEK – AGH University of Science and Technology, Cracow, Poland
Josip STJEPANDIC – PROSTEP AG, Darmstadt, Germany
Pavel A. STRIZHAK – Tomsk Polytechnic University, Russia
Vadym STUPNYTSKYY – Lviv Polytechnic National University, Ukraine
Miklós SZAKÁLL – Johannes Gutenberg-Universität Mainz, Germany
Agnieszka TOMASZEWSKA – Gdansk University of Technology, Poland
Artur TYLISZCZAK – Czestochowa University of Technology, Poland
Aneta USTRZYCKA – Institute of Fundamental Technological Research, Warsaw, Poland
Alper UYSAL – Yildiz Technical University, Turkey
Gabriel WĘCEL – Silesian University of Technology, Gliwice, Poland
Marek WĘGLOWSKI – Welding Institute, Gliwice, Poland
Frank WILL – Technische Universität Dresden, Germany
Michał WODTKE – Gdańsk University of Technology, Poland
Marek WOJTYRA – Warsaw University of Technology, Poland
Włodzimierz WRÓBLEWSKI – Silesian University of Technology, Gliwice, Poland
Hongtao WU – Nanjing University of Aeronautics and Astronautics, China
Jinyang XU – Shanghai Jiao Tong University, China
Zhiwu XU – Harbin Institute of Technology, China
Zbigniew ZAPAŁOWICZ – West Pomeranian University of Technology, Szczecin, Poland
Zdzislaw ZATORSKI – Polish Naval Academy, Gdynia, Poland
Wanming ZHAI – Southwest Jiaotong University, Chengdu, China
Xin ZHANG – Wenzhou University of Technology, China
Su ZHAO – Ningbo Institute of Materials Technology and Engineering, China



This page uses 'cookies'. Learn more