Applied sciences

Archives of Thermodynamics

Content

Archives of Thermodynamics | 2022 | vol. 43 | No 1

Download PDF Download RIS Download Bibtex

Abstract

Local wind conditions can vary strongly depending on the landmark and vegetation, as well as on the skyline of the buildings in an urban surrounding. Weather, season and time of day influence the yield of electric power. In order to promote the use of small wind turbines as an alternative to photovoltaic power generation, design optimization for locationoptimized small wind turbines was carried out. In this work, we want to concentrate on vertical axis wind turbines. Experimental studies, as well as numerical simulations, have been conducted. On the one hand, bionically optimized core structures will be integrated and implemented in the hybrid material of the turbine blades. Several optimization attempts have been examined for single blades. Detailed simulative investigations with large eddy simulations improve the aerodynamic behaviour of the new rotor design. Finally, based on the results of the studies and investigations, a new rotor will be manufactured and tested experimentally in the wind tunnel. A comparison with the reference system from the first part of the paper shows the improvements and effectiveness of the measures and processes investigated.
Go to article

Bibliography

[1] Lehser-Pfeffermann D., Häfele T., Rückert F., Griebsch J., Müller T., Joos F.: Location-optimized aerodynamic design of small wind turbines and lightweight implementation using additive hybrid material. Mech. Mech. Eng. 22(2018), 2437–445.
[2] Rezaeiha A., Kalkman I., Montazeri H., Blocken B.: Effect of the shaft on the aerodynamic performance of urban vertical axis wind turbines. Energ. Convers. Manage. 149(2017), 616–630.
[3] https://www.ansys.com/ (accessed 4 April 2021).
[4] Lehser-Pfeffermann D., Häfele T., Lehmon D., Hamman A., Griebsch J., Rückert F.: Aerodynamically and structurally optimized rotor of a vertical axis small wind turbine for suburban areas. In: Proc. ICCE2019 – 8th Int. Conf. Exhib. on Clean Energy, 12-14 August, Montreal, Canada, 2019.
[5] https://www.rhino3d.com/de/6/new/grasshopper/ (accessed 5 April 2021).
[6] Lehser-Pfeffermann D.: Untersuchung des Strömungsverlaufes einer Rotorkonzeptstudie für vertikale Kleinwindkraftanlagen, PhD thesis, Helmut-Schmidt Univ., Hamburg 2021.
[7] Lehser-Pfeffermann D., Theis D., Hamman A., Rückert F.: Investigation and evaluation of aerodynamic efficiency improvement measures for vertical axis small wind turbines. In: Proc. 6th Int. Conf. on Renewable and Non-Renewable Energy, Miami, May 20–21, 2019.
[8] http://web.mit.edu/drela/Public/web/xfoil/ (accessed 15 March 2021).
[9] MacPhee D., Beyene A.: Performance analysis of a small wind turbine equipped with flexible blades. Renew. Energ. 132(2019), 497–508,
[10] Hoogedoorn E., Jacobs G., Beyene A.: Aero-elastic behavior of a flexible blade for wind turbine application: a 2d computational study. Energy 35(2010), 2, 778–785.
[11] MacPhee D., BeyeneA.: Fluid-structure interaction of a morphing symmetrical wind turbine blade subjected to variable load. Int. J. Energ. Res. 37(2013), 1, 69–79.
[12] M. Kerho, S. Hutcherson, R.F. Blackwelder, R.H. Liebeck: vortex generators used to control laminar separation bubbles. Int. J. Aircraft 30(1993), 3, 315–319.
[13] Koehler R.: Wirbel und Schrauben in Scherströmungen. Elemente der Naturwissenschaft 20(1974), 8–25.
[14] Taneda S.: Experimental investigation of the wakes behind cylinders and plates at low reynolds numbers. J. Phys. Soc. Japan 11(1956), 3, 302–307.
[15] Benim A.C., Epple B., Krohmer B.: Modelling of pulverised coal combustion by a Eulerian-Eulerian two-phase flow formulation, Prog. Comput. Fluid Dyn. 5(2005), 6, 345–361.
[16] Ahmed A., Ibrar B., Lehser-Pfeffermann D., Theis D., Benim A., Rückert F., Joos F.: Investigation of wake flow and turbulence development behind small wind turbines. In: Proc. ICREN – 2019 Int. Conf. on Renewabl, Paris, 24–26 April, 2019.
[17] Stasko T., Majkut M., Dykas S., Smołka K.: Selection of a numerical model to predict the flowin a fan with a cycloidal rotor. Arch. Thermodyn. 42(2021), 4, 3–15.
[18] Marchewka E., Sobczak K., Reorowicz P., Obidowski S.D., Józwik K.: Application of overset mesh approach in the investigation of the Savonius wind turbines with rigid and deformable blades. Arch. Thermodyn. 42(2021), 4, 201–216.
[19] Lipian M., Dobrev I., Massouh F., Jozwik K.: Small wind turbine augmentation: Numerical investigations of shrouded- and twin-rotor wind turbines. Energy 201(2020), 117588.
Go to article

Authors and Affiliations

Daniel Lehser-Pfeffermann
1
Alexander Hamman
1
Frank Ulrich Rückert
1

  1. University of Applied Sciences Saarbrücken (htw saar), Faculty of Economic Sciences, Campus Rotenbühl, Waldhausweg 14, 66123 Saarbrücken, Germany
Download PDF Download RIS Download Bibtex

Abstract

In the presented work Egorov’s approach (adding a source term to the ω-equation in the k-! model, which mimics the damping of turbulence close to a solid wall) was implemented in on the subclass of shear stress transport models. Hence, turbulence damping is available for all shear stress transport type models, including hybrid models that are based on the ω-equation. It is shown that turbulence damping improves the prediction of the axial velocity profile not only for Reynolds-averaged Navier–Stokes simulation but also for detached eddy simulation and delayed detached eddy simulation models. Furthermore, it leads to a more realistic estimation of the pressure drop and, hence, to a more correct prediction of the liquid level. In this paper, simulation results for four different turbulence models are presented and validated by comparison with experimental data. Furthermore, the influence of the magnitude of the damping factor on the pressure drop in the channel is investigated for a variety of different gas-to-liquid flow rate ratios. These investigations show that higher gas-to-liquid flow rate ratios require higher damping factors to correctly predict the pressure drop. In the end, advice is formulated on how an appropriate damping factor can be determined for a specific test case.
Go to article

Bibliography

[1] Egorov Y., Boucker M., Martin A., Pigny S., Scheuerer M., Willemsen S.: Validation of CFD codes with PTS-relevant test cases. Tech. Rep. EVOL-ECORAD07, 2004.
[2] Fabre J., Masbernat L., Suzanne C.: Stratified flow. Part I: Local structure. Multiphas. Sci. Technol. 3(1987), 285–301.
[3] Höhne T., Vallée C.: Experiments and numerical simulations of horizontal twophase flow regimes using an interfacial area density model. J. Comput. Multiphas. Flow. 2(2010), 3, 131–143.
[4] Vallée C., Höhne T.: CFD validation of stratified two-phase flows in a horizontal channel. In: Annual Report 2006 (F.-P. Weiss, U. Rindelhardt, Eds.), FZR-465, Forschungszentrum Dresden Rossendorf, 2007, 33–38.
[5] Frederix E.M.A., Mathur A., Dovizio D., Geurts B.J., Komen E.M.J.: Reynolds-averaged modeling of turbulence damping near a large-scale interface in two-phase flow. Nucl. Eng. Design 333(2018), 122–130.
[6] Höhne T., Vallée C.: Modelling of stratified two phase flows using an interfacial area density model. In: Proc. Multiphase Flow 2009, 5th Int. Conf. on Computational and Experimental Methods in Multiphase and Complex Flow, New Forest, 15-17 June, 2009, 123–133.
[7] Höhne T., Mehlhoop J.-P.: Validation of closure models for interfacial drag and turbulence in numerical simulations of horizontal stratified gas–liquid flows. Int. J. Multiphas. Flow 62(2014), 1–16.
[8] Porombka P., Höhne,T.: Drag and turbulence modelling for free surface flows within the two-fluid Euler–Euler framework. Chem. Eng. Sci. 134(2015), 348–359.
[9] Ansys Fluent User’s Guide. Release 2021 R1. Ansys, Inc., Canonsburg 2021.
[10] Chinello G., Ayati A.A., McGlinchey D., Ooms G., Henkes R.: Comparison of computational fluid dynamics simulations and experiments for stratified air-water flows in pipes. J. Fluid. Eng. 141(2019), 5, 051302-1–051302-12.
[11] Gada V.H., Tandon M.P., Elias J., Vikulov R., Lo S.: A large scale interface multi-fluid model for simulating multiphase flows. Appl. Math. Model. 44(2017), 189–204.
[12] Lo S., Tomasello A.: Recent progress in CFD modelling of multiphase flow in horizontal and near-horizontal pipes. In: Proc. 7th North American Conf. on Multiphase Technology, Banff, June 2010, BHR-2010-F1.
[13] Fan W., Li H., Anglart H.: Numerical investigation of spatial and temporal structure of annular flow with disturbance waves. Int. J. Multiphas. Flow 110(2019), 256–272.
[14] Fan W., Anglart H.: Progress in phenomenological modeling of turbulence damping around a two-phase interface. Fluids 4(2019), 3, 136.
[15] Fan W., Anglart H.: varRhoTurbVOF 2: Modified OpenFOAM volume of fluid solvers with advanced turbulence modeling capability. Comput. Phys. Commun. 256(2020), 107467.
[16] Wilcox D.C.: Turbulence Modeling for CFD Vol. 2. DCW Industries, La Canada 1998.
[17] Menter F., Kuntz M., Langtry R.: Ten years of industrial experience with the SST turbulence model. In: Turbulence, Heat and Mass Transfer 4 (K. Hanjalic, Y. Nagano, M. Tummers, Eds.). Begell House, 2003.
[18] Langtry R.B., Menter F.R.: Correlation-based transition modeling for unstructured parallelized computational fluid dynamics codes. AIAA J. 47(2009), 12, 2894–2906.
[19] Egorov Y., Menter F.: Development and application of SST-SAS turbulence model in the desider project. In: Advances in Hybrid RANS-LES Modelling (S.-H. Peng, W. Haase, Eds.), Springer, Berlin Heidelberg, 2008, 261–270.
[20] Strelets M.: Detached eddy simulation of massively separated flows. In: Proc. 39th AIAA Aerospace Sciences Meet. Exhib., Reno, Jan. 8-11, 2001.
[21] Gritskevich M., Garbaruk A., Schütze J., Menter F.: Development of DDES and IDDES formulations for the k-ω shear stress transport model. Flow Turbul. Combust. 88(2012), 3, 431–449.
[22] Müller-Steinhagen H., Heck K.: A simple friction pressure drop correlation for two-phase flow in pipes. Chem. Eng. Process. 20(1986), 6, 297–308.
[23] Launder B., Spalding D.: The numerical computation of turbulent flows. Comput. Methods Appl. Mech. Eng. 3(1974), 2, 269– 289.
[24] Menter F.R.: Two-equation eddy-viscosity turbulence models for engineering applications. AIAA J. 32(1994), 8, 1598–1605.
[25] Spalart P., Deck S., Shur M., Squires K., Strelets M., Travin A.: A new version of detached-eddy simulation, resistant to ambiguous grid densities. Theor. Comput. Fluid Dyn. 20(2006), 181–195.
[26] Frank T.: Numerical simulation of slug flow regime for an air-water two-phase flow in horizontal pipes. In: Proc. 11th Int. Topical Meeting on Nuclear Reactor Thermal-Hydraulics (NURETH-11), Avignon, Oct. 2–6, 2005.
Go to article

Authors and Affiliations

Jiri Polansky
1
Sonja Schmelter
2

  1. Czech Technical University in Prague, Jugoslávských partyzánu 1580/3, 160 00 Prague 6 – Dejvice, Czech Republic
  2. Physikalisch-Technische Bundesanstalt (PTB), Abbestraße 2-12, D-10587 Berlin-Charlottenburg, Germany
Download PDF Download RIS Download Bibtex

Abstract

Paper is considering the purpose and the process of development of last stage blade for intermediate pressure module of 13K215 steam turbine. In the last 20–30 years most of the steam turbine manufacturers were focused on improving such a turbine mainly by upgrading low pressure module. In a result of such a modernization technology were changed from impulse to reaction. The best results of upgrading were given by developing low pressure last stage blade. With some uncertainty and based on state of art knowledge, it can be stand that improving of this part of steam turbine is close to the end. These above indicators show an element on which future research should be focused on – in the next step it should be intermediate pressure module. In the primary design the height of intermediate pressure last stage blade was 500 mm but because of change of technology this value was decreased to 400 mm. When to focus on reaction technology, the height of the last stage blade is related to output power and efficiency. Considered here is the checking the possibility of implementing blades, in a reaction technology, higher than 400 mm and potentially highest. Article shows a whole chosen methodology of topic described above. It leads through the reasons of research, limitations of 13K215 steam turbine, creation of three-dimensional models, fluid flow calculations, mechanical integrity calculations and proposed solutions of design.
Go to article

Bibliography

[1] Choudhary A., Prasad E.: Steam Turbine Market by Design (Reaction and Impulse) and Application (Power generation, Petrochemical, Oil & Gas and Others): Global Opportunity Analysis and Industry Forecast, 2020–2027. Market Research Report 2019. Allied Market Research, 2020.
[2] Termuehlen H., Emsperger W.: Steam turbine technology. In: Clean and Efficient Coal-Fired Power Plants. ASME Press, New York 2003, 60–62.
[3] Dominiczak K., Radulski W., Banaszkiewicz M., Mróz K., Bondyra R.: Thermal stress limiter for 13K215 steam turbine retrofit in Połaniec Power Plant, Poland. J. Power Technol. 96(2016), 4, 285–294.
[4] Singh M.P., Lucas G.M.: Blade design and analysis for steam turbines. McGraw- Hill, New York 2011.
[5] Reddy A.S., Ahmed M.D.I., Kumar T.S., Reddy A.V.K., Bharathi W.P.: Analysis of steam turbines. Int. Refer. J. Eng. Sci. 3(2014), 2, 32–48.
[6] Bloch H.P., Singh M.P.: Steam Turbines Design, Application, and Re-Rating. McGraw Hill Prof., 2008, 109–124, 188–218.
[7] Jansen M., Ulm W.: Modern blade design for improving steam turbine efficiency. In: Proc. 1st Eur. Conf.: Turbomachinery – Fluid Dynamic and Thermodynamic Aspects, Erlangen, 1–3 Mar 1995.
[8] Segawa K., Shikano Y., Tsubouchi K., Shibashita N.: Development of a highly loaded rotor blade for steam turbines. JSME Int. J. B-Fuid. Therm. Eng. 45(2002), 4, 881–890.
[9] Shimoyama K., Yoshimzu S, Jeong S., Obayashi S, Yokono Y.: Multi-objective design optimization for a steam turbine stator blade using LES and GA. J. Comput. Sci. Technol. 5(2011), 3, 134–47.
[10] Mohan R.S., Sarkar A., Sekhar A.S.: Vibration analysis of a steam turbine blade. In: Proc. 43rd Int. Cong. Expo. on Noise Control Engineering: Improving the World Through Noise Control., Internoise 2014 (J. Davy, T. McMinn, N. Broner, Ch. Don, L. Dowsett, M. Burgess, Eds.), Melbourne, 16–19 Nov. 2014.
[11] Heidari M., Amini K.: Structural modification of a steam turbine blade. In: Proc. IOP Conf. Ser.: Mater. Sci. Eng. 203 (2017), 012007.
[12] https://www.ansys.com/products/fluids/ansys-blademodeler (accessed 16 April 2021).
[13] https://www.ansys.com (accessed 16 April 2021).
[14] Rusanov A.V., Paschenko N.W., Kosianova A.I.: Method for analythical profiling of axial turbine blade rows. East Eur. J. Power Technol. 2(2009), 7, 32–37 (in Russian).
[15] Lampart P., Ershov S.: 3D shape optimisation of turbomachinery blading. TASK Quart. 6(2002), 1, 113–125.
[16] https://www.ansys.com/products/fluids/ansys-cfx (accessed 16 Apr. 2021).
[17] https://www.ansys.com/products/fluids/ansys-turbogrid (accessed 16 Apr. 2021).
[18] Yoon S., Vandeputte T., Mistry H., Ong J., Stein A.: Loss audit of a turbine stage. J. Turbomach. 138(2016), 5, 051004.
[19] https://www.3ds.com/products-services/catia/ (accessed 10 March 2021).
[20] Stuck Z., Schurdak S.: Steam turbine blade design. In: Proc. 20th Ann. Freshman Conf., 14 April 2012, 2214.
[21] Rzadkowski R., Kubitz L., Maziarz M., Troka P., Dominiczak K., Szczepanik R.: Tip-timing measurements and numerical analysis of last-stage steam turbine mistuned bladed disc during run-down. J. Vib. Eng. Technol. 8(2020), 3, 409– 415.
[22] Rzadkowski R., Lampart P., Kwapisz L., Szymaniak M., Drewczynski M.: Transient thermodynamic, thermal and structure analysis of a steam turbine during its start-up. In: Proc. ASME Turbo Expo 2010: Power for Land, Sea and Air, Vol. 4: Heat Transfer, Glasgow, June 14–18, 2010, GT 2010-22813, 2010, 1103–1112.
[23] Dominiczak K., Rzadkowski R., Radulski W., Szczepanik R.: Online prediction of temperature and stress in steam turbine components using neural network. J. Eng. Gas Turbines Powers 138(2016), 5: 052606.
[24] Singh M.P., Vargo J.J., Schiffer D.M., Dello J.D.: SAFE diagram – A design and reliability tool for turbine blading. In: Proc. 17th Turbomachinery Symp. Houston, 1988, 93–102, Texas A&M Univ. Turbomach. Lab.
[25] Singh M.P.: History of evolution, progress and application of SAFE diagram for tuned and mistuned systems. In: Proc. 42nd Turbomachinery Symp., Houston, Oct. 1-3, 2013, Texas A&M Univ. Turbomach. Lab.
Go to article

Authors and Affiliations

Radoslaw Bondyra
1
Jan Przytulski
1
Krzysztof Dominiczak
2

  1. GE Power Ltd, Stoczniowa 2, 82-300 Elblag, Poland
  2. Institute of Fluid Flow Machinery Polish Academy of Sciences, Fiszera 14, 80-231 Gdansk, Poland
Download PDF Download RIS Download Bibtex

Abstract

The results of the gas-dynamic calculation of the low-pressure cylinder flow part of the K-220-44 type steam turbine intended for operation at nuclear power plants are presented. The ways of the flow part improvement were determined. Some of those ways include the use of innovative approaches that were not previously used in steam turbines. The design of the new flow part was carried out on the basis of a comprehensive methodology implemented in the IPMFlow software package. The methodology includes gas-dynamic calculations of various levels of complexity, as well as methods for analytical construction of the spatial shape of the blade tracts based on a limited number of parameterized values. The real thermodynamic properties of water and steam were taken into account in 3D calculations of turbulent flows. At the final step, end-to-end 3D calculations of the lowpressure cylinder that consists of 5 stages were performed. The technology of parallel computing was applied in those calculations. It is shown that due to the application of innovative solutions, a significant increase in efficiency can be achieved in the developed low-pressure cylinder.
Go to article

Bibliography

[1] Rosenkranz G.: Myths of Nuclear Energy. How we are deceived by the Energy Lobby. Heinrich-Böll-Stiftung, Brussels 2010.
[2] Duffey R., Pioro I.: Ensuring the Future of Nuclear Power. ASME Mech. Eng. 141(2019), 11, 30–35.
[3] Moore Ch., Brown S., Alparslan U., Cremona E., Alster G.: European Electricity Review 6-month update H1-2021. Ember, July 2021. https://emberclimate.org/project/european-electricity-review-h1-2021/ (accessed 16 Sept. 2021).
[4] Directive 2004/8/EC of the European Parliament and of the Council of 11 February 2004 on the promotion of cogeneration based on a useful heat demand in the internal energy market and amending Directive 92/42/EEC. O.J.L 52/50, 11 Feb. 2004, p. 60.
[5] Alparslan U.: Turkey, Ukraine and Western Balkan countries compete for top spot in coal power air pollution in Europe. Ember, May 25, 2021. https://emberclimate.org/commentary/2021/05/25/coal-power-air-pollution/ (accessed 16 Sept. 2021).
[6] Maradin D.: Advantages and disadvantages of renewable energy sources utilization. Int. J. Energ. Econ. Policy 11(2021), 3, 176-183.
[7] Nuclear Power in the European Union. World-Nuclear Assoc. rep. Feb. 2021. https://www.world-nuclear.org/information-library/country-profiles/others/europeanunion.aspx (accessed 16 Sept. 2021).
[8] Nuclear Power in the World Today. World-Nuclear Assoc. rep., June 2021. https://world-nuclear.org/information-library/current-and-future-generation/nuclear-powerin-the-world-today.aspx (accessed 16 Sept. 2021).
[9] Ojovan M.I., Lee W.E.: An Introduction to Nuclear Waste Immobilisation. Elsevier, Amsterdam 2005.
[10] Energoatom and Westinghouse strengthen bilateral cooperation. Energoatom. https://www.energoatom.com.ua/en/press_center-19/company-20/p/energoatom_ and_westinghouse_strengthen_bilateral_cooperation-47995 (accessed 20 Sept. 2021).
[11] Hibbs M.: The Future of Nuclear Power in China. Carnegie Endowment for International Peace, Washington, DC 2018.
[12] EIA Open Data. U.S. Energy Information Administration. https://www.eia.gov/ (accessed 15 Aug. 2021).
[13] Jun G., Kolovratník M., Hoznedl M.: Wet steam flow in 1100 MW turbine. Arch. Thermodyn. 42(2021), 3, 63–85.
[14] Shvetsov V., Galatsan V.: PJSC “Turboatom” works in modernization and improvement of NPP turbines. Bull. National Technical University “KhPI”, ser. Power Heat Eng. Process. Equip. (2007), 2, 6–10 (in Russian).
[15] Lifetime extension of SE ZNPP power units. Zaporizhzhia NPP. https://www.npp.zp.ua/en/activities/lifetime-extension (accessed 15 Sept. 2021).
[16] Nuclear Power in Ukraine. World-Nuclear Association, rep. from Aug. 2021. https://world-nuclear.org/information-library/country-profiles/countries-t-z/ukraine.aspx (accessed 16 Sept. 2021).
[17] Yershov S., Rusanov A., Gardzilewicz A., Lampart P.: Calculations of 3D viscous compressible turbomachinery flows. In: Proc. 2nd Symp. on Comp. Technologies for Fluid/Thermal/Chemical Systems with Industrial Applications. ASME PVP Division Conf., 1-5 August 1999, Boston, PVP, 397.2(1999), 143–154.
[18] Menter F.R.: Two-equation eddy viscosity turbulence models for engineering applications. AIAA J. 32 (1994), 8, 1598–1605.
[19] Rusanov A.V., Lampart P., Pashchenko N.V., Rusanov R.A.: Modelling 3D steam turbine flow using thermodynamic properties of steam IAPWS-95. Pol. Marit. Res. 23(2016), 1, 61–67.
[20] Rusanov A., Rusanov R., Klonowicz P., Lampart P., Zywica G., Borsukiewicz A.: Development and experimental validation of real fluid models for CFD calculation of ORC and steam turbine flows. Materials 14(2021), 6879.
[21] Lampart P., Gardzilewicz A., Rusanov A., Yershov S.: The effect of stator blade compound lean and twist on flow characteristics of a turbine stage - numerical study based on 3D RANS simulations. In: Proc. 2nd Symp. on Comp. Technologies for Fluid/Thermal/Chemical Systems with Industrial Applications, ASME PVP Div. Conf., 1–5 Aug. 1999, Boston 397.2 (1999), 195–204.
[22] Fischer P.F., Venugopal M.: A commercial CFD application on a shared memory multiprocessor using MPI. Editor(s): In: Parallel Computational Fluid Dynamics 1995 (A. Ecer, J. Periaux, N. Satdfuka, S. Taylor, Eds.). North-Holland, 1996, 231– 238.
[23] Rusanov A., Rusanov R., Lampart P.: Designing and updating the flow part of axial and radial-axial turbines through mathematical modeling. Open Eng. 5(2015), 399–410.
[24] Kosiak Yu.F.: Steam Turbine for Nuclear Power Plants. Energia, Moscow 1978 (in Russian).
[25] Akkerman G., Hampel R., Hentshel G.: Investigation of the operating modes of NPP with VVER. Teploenergetika (1976), 11, 85–87 (in Russian).
[26] Miettinen E., Loukia A., Vuorennaia A.: Experience in setting up and operating the turbine unit of the NPP “Loviisa-1”. Teploenergetika (1980), 2, 36–40 (in Russian).
[27] Konovalov G.M., Korsh A.K., Pomerantsev L.I.: Efficiency of serial NPP units with a capacity of 440 MW with VVER 440 reactors. Teploenergetika (1975), 9, 52–56 (in Russian).
[28] Arkadiev B.A.: Nuclear Power Plant Turbine Operation Modes. Energoizdat, Moscow 1986 (in Russian).

Go to article

Authors and Affiliations

Andrii Rusanov
1
Viktor Subotin
2
Viktor Shvetsov
2
Roman Rusanov
1
Serhii Palkov
1 2
Ihor Palkov
1 2
Marina Chugay
1

  1. The A.N. Podgorny Institute for Mechanical Engineering Problems, National Academy of Sciences of Ukraine, Pozharsky 2/10, 61046 Kharkiv, Ukraine
  2. JSC “Ukrainian Energy Machines” Moskovsky 199, 61037 Kharkiv, Ukraine
Download PDF Download RIS Download Bibtex

Abstract

Artificial neural networks are gaining popularity thank to their fast and accurate response paired with low computing power requirements. They have been proven as a method for compressor performance prediction with satisfactory results. In this paper a new approach of artificial neural networks modelling is evaluated. The auxiliary parameter of ‘relative stability margin Z’ was introduced and used in learning process. This approach connects two methods of compressor modelling such as neuralnetworks and auxiliary parameter utilization. Two models were created, one with utilization of the ‘relative stability margin Z’ as a direct indication of surge margin of any estimated condition, and other with standard compressor parameters. The results were compared by determination of fitting, interpolation and extrapolation capabilities of both approaches. The artificial neural networks used during the process was a two-layer feed-forward neural-network with Levenberg–Marquardt algorithm with Bayesian regularization. The experimental data was interpolated to increase the amount of learning data for the neural network. With the two models created, capabilities of this relatively simple type of neural-network to approximate compressor map was also assessed.
Go to article

Bibliography

[1] Sieber J.: European Technology Programs for Eco-Efficient Ducted Turbofans. ISABE-2015-20029, 2015.
[2] European Commission, Directorate-General for Mobility and Transport, Directorate- General for Research and Innovation. Flightpath 2050: Europe’s vision for aviation: maintaining global leadership and serving society’s needs. Publications Office, 2011.
[3] Orkisz M., Stawarz S.: Modeling of turbine engine axial-flow compressor and turbine characteristics. J. Propul. Power 16(2000), 2, 336–339.
[4] Gholamrezaei M., Ghorbanian K.: Compressor map generation using a feedforward neural network and rig data. P.I. Mech. Eng. A: J. Power Energ. 224(2010), 1, 97–108.
[5] Tsoutsanis E., Meskin N., Benammar M., Khorasani K.: Transient gas turbine performance diagnostics through nonlinear adaptation of compressor and turbine maps. ASME J. Eng. Gas Turbines Power 137(2015), 9, 091201.
[6] Walsh P., Fletcher P.: Gas Turbine Performance. Blackwel, Bristol 2004.
[7] Sethi V., Doulgeris G., Pilidis P., Nind, A., Doussinault M., Cobas P., Rueda A.: The map fitting tool methodology: gas turbine compressor off-design performance modeling. ASME J. Turbomach. 135(2013), 6, 061010.
[8] Kurzke J.: How to get component maps for aircraft gas turbine performance calculations. Proc. ASME 1996 Int. Gas Turbine and Aeroengine Cong. Exhibit., Vol. 5, Birmingham, June 10–13, 1996, V005T16A0011996. ASME Pap. 96-GT-164.
[9] Misté G., Benini E.: Improvements in off design aeroengine performance prediction using analytic compressor map interpolation. Int. J. Turbo Jet Eng. 29(2012), 69–77.
[10] Muszynski M., Orkisz M.: Turbine Jet Engine Modelling. Ser. Scientific Library 7, Institute of Aviation, Warszawa 1997 (in Polish).
[11] Jones G., Pilidis P., Curnock B.: Extrapolation of Compressor Characteristics to the Low-Speed Region for Sub-Idle Performance Modelling. Proc. ASME Turbo Expo 2002, Power for Land, Sea, and Air, Vol, 2, Turbo Expo 2002, Pts., A, B, Amsterdam, June 3–6, 2002, 861–867. ASME Pap. GT2002–30649.
[12] De-You Y., Zhong-Fan M.: A dynamic model of turbojet in starting at high altitude. AIAA Pap. 83–7045, 1983.
[13] Jensen J., Kristensen A., Sorenson S., Houbak N. Hendricks E.: Mean value modeling of a small turbocharged diesel engine. SAE Tech. Pap. 910070, 1991.
[14] Tsoutsanis E., Meskin N., Benammar M., Khorasani K.: A component map tuning method for performance prediction and diagnostics of gas turbine compressors. Appl. Energ. 135(2014), 572–585.
[15] Tsoutsanis E., Meskin N., Benammar M., Khorasani K.: An Efficient Component Map Generation Method for Prediction of Gas Turbine Performance. Proc. ASME Turbo Expo 2014, Turbine Technical Conference and Exposition, Vol. 6, Düsseldorf, June 16–20, 2014, V006T06A006, ASME Pap. GT2014–25753.
[16] Trawinski P.: Development of flow and efficiency characteristics of an axial compressor with an analytical method including cooling air extraction and variable inlet guide vane angle. Arch. Thermodyn. 42(2021), 4, 17–46.
[17] Converse G.L., Giffen R.G.: Representation of Compressor Fans and Turbines. Vol. 1. CMGEN User’s Manual, NASA-CR-174645, 1984.
[18] Kong C., Ki J., Kang M.: A new scaling method for component maps of gas turbine using system identification. ASME J. Eng. Gas Turbines Power 125(2003), 4, 979–985.
[19] Kong C., Kho S., Ki J.: Component map generation of a gas turbine using genetic algorithms. ASME J. Eng. Gas Turbines Power 128(2006), 1, 92–96.
[20] Kong C., Ki J., Lee C.: Components map generation of gas turbine engine using genetic algorithms and engine performance deck data. Proc. ASME Turbo Expo 2006, Power for Land, Sea, and Air, Vol. 4, Barcelona, May 8–11, 2006, 377–383. ASME Pap. GT2006–90975.
[21] Zagorowska M., Thornhill N.: Compressor map approximation using Chebyshev polynominals. In: Proc. IEEE 2017, 25th Mediterranean Conf. on Control and Automation, Valletta, July 3–6, 2017, 864–869.
[22] Li X., Yang C., Wang Y., Wang H., Zu X., Sun Y., Hu S.: Compressor map regression modelling based on partial least squares. R. Soc. Open Sci. 5(2018), 8, 172454.
[23] Ghorbanian K., Gholamrezaei Mohammad.: An artificial neural network approach to compressor performance prediction. Appl. Energ. 86(2009), 1210–1221.
[24] Ghorbanian K, Gholamrezaei M.: Axial compressor performance map prediction using artificial neural network. Proc. ASME Turbo Expo 2007, Power for Land, Sea, and Air, Vol. 6, Turbo Expo 2007, Pts. A, B, Montreal, May 14-17, 2007, 1199–1208, ASME Pap. GT2007–27165.
[25] Youhong Y., Lingen Ch., Fengrui S., Chih W.: Neural-network based analysis and prediction of a compressor’s characteristic performance map. Appl. Energ. 84(2007), 1, 48–55.
[26] Hornik K., Stinchcombe M., White H.: Multilayer feedforward networks are universal approximators. Neural Networks 2(1989), 5, 359–366.
[27] Pinkus A.: Approximation theory of the MLP model in neural networks. Acta Numerica, 8(1999), 143–195.
[28] Hagan M.T., Demuth H.B., Jesús O.D.: An introduction to the use of neural networks in control systems. Int. J. Robust Nonlin. Contr. 12(2002), 959–985.
[29] www.mathworks.com/help/deeplearning/ref/neuralnetfitting-app.html (accessed 17 Apr. 2021).
[30] Hagan M.T., Menhaj M.B.: Training feedforward networks with the Marquardt algorithm. IEEE T. Neural Netw. 5(1994), 6, 989–993.
[31] Burden F., Winkler D.: Bayesian regularization of neural networks. In: Artificial Neural Networks), ser. Methods in Molecular Biology Vol. 458 (D.J. Livingstone, Eds.). Humana Press, 2008.
Go to article

Authors and Affiliations

Sergiusz Michał Loryś
1
Marek Orkisz
2

  1. Hamilton Sundstrand Poland / Pratt & Whitney AeroPower Rzeszów, Hetmanska 120, 35-078 Rzeszów, Poland
  2. Rzeszow University of Technology, Department of Aerospace Engineering, Powstanców Warszawy 8, 35-959 Rzeszów, Poland
Download PDF Download RIS Download Bibtex

Abstract

Air pollution has a serious impact on the health of human beings and is a major cause of death worldwide every year. Out of the many sources of air pollution, the smoke generated from household combustion devices is very dangerous due to the incomplete combustion of fuel. Women from rural areas suffer a lot due to this harmful smoke. Diseases like cancer, throat, and lung infection occur in adults and children due to inhalation of this smoke. The traditional chulha used by rural women is operated by using cow dung, straw, and wood, and the air is blown manually by using small metallic pipes. This paper presents the design and development of an innovative stove to maximize flame temperature and minimize air pollution to overcome the health-related issues of rural women. A smokeless stove is presented, in which wood, straw, and cow dung are taken as primary fuel, and superheated steam as a secondary oxidizer for its operation. In this stove, a forced draft is created by the provision of a small fan, which is operated by solar power thus eliminating the need of creating a forced draft manually by the cook which makes this innovative stove superior to the traditional chulha. Owing to the provision of superheated steam, the flame temperature as well as the burning efficiency increases. The cooking time is reduced due to higher flame temperature as compared to the liquefied petroleum gas stove. The main objective of this work is to minimize air pollution and provide a smoke-free environment to the people using such devices as this innovative stove offers complete combustion of fuel. The flame temperature of the designed stove ranges from 595˚C to 700˚C and its thermal efficiency is 10–17% higher than that of the traditional chulha. The design of this stove is unique, and its maintenance cost is also much less.
Go to article

Bibliography

[1] James B.S., Shetty R.S., Kamath A., Shetty A.: Household cooking fuel use and its health effects among rural women in southern India — A cross-sectional study. PLoS ONE 15(2020), 4, e0231757.
[2] Balakrishnan K.: Examining health effects of air pollution in India. ICMR Cent. Adv. Res. Environ. Health, New Delhi 2013.
[3] Onah I., Ayuba H.K., Idris N.M.: Estimation of fuelwood-induced carbon emission from the use of improved cook stoves by selected households in Kwara State, Nigeria. Clim. Change 160 (2020), 3, 463–477.
[4] Obi O.F., Ezema J.C., Okonkwo W.I.: Energy performance of biomass cookstoves using fuel briquettes. Biofuels 11 (2020), 4, 467–478.
[5] Woldesemayate A.T., Atnaw S.M.: A review on design and performance of improved biomass cooks stoves. L. N. Inst. Comp. Sci. Soc.-Inf. Telecomm. Eng. LNICST 308(2020), 557–565.
[6] Flores W.C., Bustamante B., Pino H.N., Al-Sumaiti A., Rivera S.: A national strategy proposal for improved cooking stove adoption in Honduras: Energy consumption and cost-benefit analysis. Energies 13(2020), 4, en13040921.
[7] Mekonnen B.Y., Hassen A.A.: Design, construction and testing of hybrid solarbiomass cook stove. L. N. Inst. Comp. Sci. Soc.-Inf. Telecomm. Eng. LNICST 274 (2019), 225–238.
[8] Jain T., Sheth P.N.: Design of energy utilization test for a biomass cook stove. Formulation of an optimum air flow recipe. Energy 166(2019), 1097–1105.
[9] Manyuchi M.M., Mbohwa C., Muzenda E., Mpeta, M.: Adoption of eco cook stoves as a way of improving energy efficiency. In: Proc. Int. Conf. on Industrial Engineering and Operations Management, Pilsen, July 23–26, 2019, 35–39.
[10] Prasannakumaran K.M., Karthikeyan M., Sanjay Kumar C., Premkumar, D., Kirubakaran V.: Integration of cooking trays for waste heat recovery in the energy efficient wood stove. Indian J. Environ. Prot. 39(2019), 1, 69–73.
[11] Emetere M.E., Okonkwo O.D., Jack-Quincy S.: Investigating heat sink properties for an efficient construction of energy generating cook stove for rural settler. Int. J. Manuf. Mater. Mech. Eng. 8(2018), 3, 12–22.
[12] Tom S., Shuma M.R., Madyira D.M., Kaymakci A.: Performance testing of a multi-layer biomass briquette stove. In: Proc. Conf. Ind. Commer. Use Energy ICUE (2017), 8068008.
[13] Roul M.K., Nayak, R.C.: Experimental investigation of natural convection heat transfer through heated vertical tubes. Int. J. Eng Res Appl. 2(2012), 6, 1088–1096.
[14] Nayak R.C., Roul M.K., Sarangi S.K.: Experimental investigation of natural convection heat transfer in heated vertical tubes with discrete rings. Exp. Tech. 41(2017), 585–603.
[15] Nayak R.C., Roul M.K., Sarangi S.K.: Experimental investigation of natural convection heat transfer in heated vertical tubes. Int. J. Appl. Eng. Res. 12(2017), 2538–2550.
[16] Nayak R.C., Roul M.K., Sarangi, S.K.: Natural convection heat transfer in heated vertical tubes with internal rings. Arch. Thermodyn. 39(2018), 4, 85–111.
[17] Sahoo L.K., Roul, M.K., Swain R.K.: CFD analysis of steady laminar natural convection heat transfer from a pin finned isothermal vertical plate. Heat Transf. – Asian Res. 46(2017), 840–862.
[18] Sahoo L.K., Roul M.K., Swain R.K.: Natural convection heat transfer augmentation factor with square conductive pin fin arrays. J. Appl. Mech. Tech. Phys. 58(2017), 1115–1122.
[19] Sahoo L.K., Roul M.K., Swain R.K.: CFD analysis of natural convection heat transfer augmentation from square conductive horizontal and inclined pin fin arrays. Int. J. Ambient Energy 39(2018), 840–851.
[20] Baqir M., Bharti S.K., Kothari R., Singh, R.P.: Assessment of an energyefficient metal stove for solid biomass fuel and evaluation of its performance. Int. J. Environ. Sci. Technol. 16(2019), 11, 6773–6784.
[21] Saravanna J.Y., KantamnenR., Fasil N., Sivamani S., Hariram V., Micha Premkumar T., Mohan., T.: Modelling and analysis of water heating using recovered waste heat from hot flue gases of stove. ARPN J. Eng. Appl. Sci. 12(2017), 21, 6164–6171.
[22] Thakur M., Boudewijns E.A., Babu G.R., Winkens B., de Witte L.P., Gruiskens J., Sushama P., Ghergu C.T., van Schayck O.C.P.: Low-smoke stove in Indian slums: Study protocol for a randomised controlled trial. BMC Public Health 17(2017), 1, 454.
[23] Smith K.R., Sagar A.: Making the clean available: Escaping India’s Stove Trap. Energy Policy 75(2014), 410–414.
[24] Hanbar R.D., Karve, P.: National Programme on Improved Stove (NPIC) of the Government of India: an overview. Energy Sustain. Dev. 6(2002), 2, 49–55.
[25] Gowda M.C., Raghavan G.S.V., Ranganna B., Barrington S.: Rural waste management in a south Indian village – A case study. Bioresour. Technol. 53(1995), 2, 157–164.
[26] Wang Y., Bailis R.: The revolution from the kitchen: Social processes of the removal of traditional cookstoves in Himachal Pradesh, India. Energy Sustain. Dev. 27(2015), 127–136.
[27] Kammen D.M.: Cook stoves for the developing world. Sci. Am. 273(1995), 1, 72–75.
[28] Asi E.M.: An integrated analytical framework for analysing expansive learning in improved cook stove practice. Learn. Cult. Soc. Interact. 26(2020), 100414.
[29] Kshirsagar M.P., Kalamkar V.R.: Application of multi-response robust parameter design for performance optimization of a hybrid draft biomass cook stove. Renew. Energy 153(2020), 1127–1139.
[30] Koroll G.W., Mulpuru S.R.: The effect of dilution with steam on the burning velocity and structure of premixed hydrogen flames. Symp. (Int.) Combust. 21(1988), 1, 1811–1819.
[31] Mujumdar A.S.: Superheated steam drying. In: Handbook of Industrial Drying (3rd Edn.). CRC Press, Boca Raton 2006.
[32] Potter D.: Measuring Temperature with Thermocouples – A Tutorial. National Instruments Application Note 043, Nov. (1996).
Go to article

Authors and Affiliations

Ramesh Chandra Nayak
1
Manmatha K. Roul
2
Prateek Debadarsi Roul
3

  1. Synergy Institute of Technology, Bhubaneswar – 752101, Odisha, India
  2. GITA Autonomous College, Bhubaneswar – 752054, Odisha, India
  3. Odisha University of Technology and Research, Bhubaneswar – 751003, Odisha, India
Download PDF Download RIS Download Bibtex

Abstract

In this paper, the logarithmic mean temperature difference method is used to determine the heat power of a tube-in-tube exchanger. Analytical solutions of the heat balance equations for the exchanger are presented. The considerations are illustrated by an example solution of the problem. In particular, the heat power of the tube-in-tube heat exchanger is determined taking into account the variants of work in the co-current and counter-current mode. Apart from the analytical solutions, appropriate numerical calculations in Matlab environment have been carried out.
Go to article

Bibliography

[1] Andrzejczyk R., Muszynski T.: Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator. Arch. Thermodyn. 40(2019), 2, 17–33.
[2] Bury T., Składzien J., Widziewicz K.: Experimental and numerical analyses of finned cross flow heat exchangers efficiency under non-uniform gas inlet flow conditions. Arch. Thermodyn. 31(2010), 4, 133–144.
[3] Hobler T.: Heat Transfer and Exchangers. Warszawa 1971 (in Polish).
[4] Kuppan T.: Heat Exchanger Design Handbook (2nd Edn.). CRC Press Taylor & Francis Group, Boca Raton 2013.
[5] Nitsche M., Gbadamosi R.O.: Heat Exchanger Design Guide. Elsevier, New York 2016.
[6] Pakowski Z., Adamski R.: Fundamentals of MATLAB in Process Engineering. Lodz Univ. Technol. Press, Łódz 2014 (in Polish).
[7] Roetzel W., Luo X.: Thermal analysis of heat exchanger networks. Arch. Thermodyn. 26(2005), 1, 5–16.
[8] Shah R.K., Sekulic D.P.: Fundamentals of Heat Exchanger Ddesign. Wiley, Hoboken 2003.
[9] Smith E.M.: Thermal Design of Heat Exchangers. A Numerical Approach: Direct- Sizing and Step-Wise Rating. Wiley, Chichester 1997.
[10] Taler D.: Numerical Modeling and Experimental Testing of Heat Exchangers. Springer, Berlin 2018.
Go to article

Authors and Affiliations

Kazimierz Rup
1

  1. Cracow University of Technology, al. Jana Pawła II 37, Cracow, Poland
Download PDF Download RIS Download Bibtex

Abstract

This paper presents the influence of cooling water regulation on power plant net efficiency. It was examined whether, for the non-nominal low-pressure turbine load, it is justified to reduce the cooling water pump load, and how it would affect the unit net efficiency. Calculations for two types of power units were carried out: with condensing and extractioncondensing turbine. The tested condensing power plant consists of three surface condensers. The calculation included four condensers’ connections set up on the cooling water side to check how the cooling water system pressure drop affects the net unit performance. The result has confirmed that implementing serial connection decreases net efficiency when cooling water flow regulation is used, but the mixed connection should be applied when pump load is not controlled. It was proved that the cooling water flow control gives a profit for both units. Net efficiency for combined heat and power plant can be improved by 0.1–0.5 pp, the gain is remarkable below 60% of the low-pressure turbine part load. Flow control implementation in the unit with condensing turbine water control gives a similar profit just below 80% of the turbine load. Next, an influence of the additional limitations of a cooling water system (minimal total pump head, cooling tower) affecting the feasibility of implementing the water control has been considered. Applying a multi-cell forced draft cooling tower does not have a significant impact on results, but when a natural draft cooling tower is used, the flow control range is strongly reduced.
Go to article

Bibliography

[1] Chmielniak T., Łukowicz H.: Modeling and optimization of coal power units with CO2 capture. WPS, Gliwice 2015 (in Polish).
[2] Chmielniak T., Łukowicz H.: Condensing power plant cycle assessing possibilities of improving its e?ciency. Arch. Thermodyn. 31(2010), 3, 105–113.
[3] Grzesiczek E., Mendecki J., Komarnicki Z.: Optimization of cooling water flow in 225 MW turbine condenser. Energetyka (2007), 8, 574–575.
[4] Rusak J.: Reduction of auxiliary energy consumption in TAURON Wytwarzanie S.A. on the example of cooling water systems modernization. Energetyka (2013), 1, 43–47.
[5] Laskowski R.: Wybrane zagadnienia modelowania i optymalizacji skraplaczy energetycznych i wymienników regeneracyjnych. Warszawa: Oficyna Wydawnicza Politechniki Warszawskiej, 2018.
[6] Laskowski R., Smyk A., Rusowicz A., Grzebielec A.: Optimization of the cooling water mass flow rate under variable load of a power unit. Appl. Therm. Eng. 191(2021), 116874.
[7] Gardzilewicz A., Błaszczyk A., Głuch J.: Operating and economic conditions of cooling water control for marine steam turbine condensers. Pol. Marit. Res. 18(2011), 3(70), 48–54.
[8] Harish R., Subhramanyan E.E., Madhavan R., Vidyanand S.: Theoretical model for evaluation of variable frequency drive for cooling water pumps in sea water based once through condenser cooling water systems. Appl. Therm. Eng. 30(2010), 2051–2057.
[9] Xia L., Liu D., Zhou L., Wang P., Chen Y.: Optimization of a seawater oncethrough cooling system with variable speed pumps in fossil fuel power plants. Int. J. Therm. Sci., 91(2015), 105–112.
[10] Dobkiewicz-Wieczorek E.: Cooling water mass flow optimization for low load of condensing turbine including CHP turbine. Rynek Energii (2020), 6, 15–20.
[11] Dobkiewicz-Wieczorek E.: Influence of surface condensers connection configuration on power plant unit performance. Arch. Thermodyn. 41(2020), 4, 115–145.
[12] Revised Release on the IAPWS Industrial Formulation 1997 for the Thermodynamic Properties of Water and Steam, The International Association for the Properties of Water and Steam. Lucerne 1997.
[13] Dobkiewicz-Wieczorek E.: Method for calculating the exhaust steam pressure of a condensing turbine. Energetyka (2019), 11, 725–730.
[14] KSB, Tips for the correct design of pumping stations equipped with submersible pumps. https://www.ksb.com/blob/173022/c7fe2d9f8e342c707efa5e0966136752/pumpenstation-download-data.pdf (accessed 6 Oct. 2021). [15] PN-76/M-34034 Pipelines – Principles of pressure loss calculations.
[16] EMBER, Average monthly wholesale electricity prices. https://ember-climate.org/european-electricity-transition/ (accessed 6 Oct. 2021).
[17] Market electrical energy price. https://wysokienapiecie.pl/40547-o-ile-wzrosna-cenypradu-w-2022-policzylismy/ (accessed 6 Oct. 2021).
[18] PSE, Daily market electrical energy price. https://www.pse.pl/dane-systemowe/funkcjonowanie-rb/raporty-dobowe-z-funkcjonowania-rb/podstawowe-wskazniki -cenowe-i-kosztowe/rynkowa-cena-energii-elektrycznej-rce (accessed 6 Oct. 2021).
Go to article

Authors and Affiliations

Ewa Dobkiewicz-Wieczorek
1

  1. Silesian University of Technology Department of Power Engineering and Turbomachinery, Konarskiego 18, 44-100, Gliwice, Poland
Download PDF Download RIS Download Bibtex

Abstract

This paper presents a test stand equipped, among others, with two boilers intended for the combustion of solid fuels. The first is a single-fuel boiler designed to burn wood pellets only. The second is a multi-fuel boiler intended for the combustion of mainly hard coal (basic fuel) with the grain size of 0.005–0.025 m. Wood pellets can also be fired in this boiler, which in such a case are treated as a substitute fuel. There is a developed and verified algorithm for the control of the multi-fuel boiler operation in a wide range of loads for the basic fuel. However, for the substitute fuel (wood pellets) there are no documented and confirmed results of such testing. The paper presents selected results of testing performed during the combustion of wood pellets in a multi-fuel automatically stoked boiler. Several measuring series were carried out, for which optimal operating conditions were indicated. These conditions may serve as the basis for the development of the boiler operation control algorithm. A detailed analysis was carried out of the flue gas temperatures obtained at the outlet of the boiler combustion chamber and of the contents of carbon monoxide and oxygen in the boiler flue gases.
Go to article

Bibliography

[1] Announcement of the Sejm Speaker of the Republic of Poland on the promulgation of a consolidated text of the Act on renewable energy sources. Journal of Laws – Republic of Poland (Dziennik Ustaw Rzeczypospolitej Polskiej) 2021, Item 610 (in Polish).
[2] Regulation of the Minister of Development and Finance on the requirements for solid-fuel boilers. Journal of Laws – Republic of Poland (Dziennik Ustaw Rzeczypospolitej Polskiej) 2017, Item 1690 (in Polish).
[3] EN 303-5:2021: Heating boilers – Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW – Terminology, requirements, testing and marking.
[4] Poland’s Energy Policy until 2040. Ministry of Climate and the Environment, Appendix to Resolution 22/2021 of the Council of Ministers, 2021 (in Polish).
[5] Commission Regulation (EU) 2019/2146 amending Regulation (EC) 1099/2008 of the European Parliament and of the Council on energy statistics, as regards the implementation of updates for the annual, monthly and short-term monthly energy statistics. OJ L 325, 16.12.2019.
[6] Directive (EU) 2018/2001 of the European Parliament and of the Council on the promotion of the use of energy from renewable sources. OJ L 328, 21.12.2018.
[7] Zima W., Ojczyk G.: Current status and prospects for solid multi-fuel boilers of low power. Rynek Energii 5(2013), 108, 50–56 (in Polish).
[8] Juszczak M., Pałaszynska K., Rolirad K., Janicki M., Szczechowiak E.: Attempt to use additives increasing ash melting point while firing agricultural biomass pellets in order to avoid slag production in the furnace. Ciepłownictwo, Ogrzewnictwo, Wentylacja 48(2017), 8, 320–326 (in Polish).
[9] Ciupek B., Urbaniak R., Judt W.: Experimental research of changes in co, nox and pm concentrations in flue gases during combustion of wood pellets with wheat seeds. Ciepłownictwo, Ogrzewnictwo, Wentylacja 50(2019), 2, 56–61.
[10] Orłowska A., Sroka K.: Changes in legal regulations concerning supplying households with heat. Rynek Energii 140(2019), 1, 38–47.
[11] Zima W., Ojczyk G.: Analysis of combustion of wood pellets as a substitute fuel in a low-power boiler. Arch. Combust. 35(2015), 2, 117–130.
[12] Ziebik A., Stanek W.: Energy effciency – selected thermo-ecological problems. Arch. Thermodyn. 41(2020), 2, 277–299.
[13] https://www.herz-energie.at/pl/ (accessed 6 Sept. 2021).
[14] http://www.ogniwobiecz.com.pl/ (accessed 12 Sept. 2021).
[15] Ecological Safety Mark: Certificate 1035. Inst. Chem. Process. Coal, Zabrze 2009 (in Polish).
[16] https://www.keison.co.uk/ (accessed 17 Aug. 2021).
[17] Kuznetsov N.V., Mitor V.V., Dubovsky I.E., Karasina E.S. (Eds.): Thermal Calculation of Steam Boilers. Normative Method (2nd Edn.). Energia, Moscow 1973 (in Russian).
[18] Rutkowski Ł., Szczygieł I.: Calculation of the furnace exit gas temperature of stoker fired boilers. Arch. Thermodyn. 42(2021), 3, 3–24.


Go to article

Authors and Affiliations

Wiesław Zima
1
Grzegorz Ojczyk
2

  1. Cracow University of Technology, Department of Energy, al. Jana Pawła II 37, 31-864 Kraków, Poland
  2. MTHE Modern Technologies in Heating Engineering, Młynska-Boczna 7/2, 31-470 Kraków, Poland
Download PDF Download RIS Download Bibtex

Abstract

This paper presents the experimental investigation of an earthto- air heat exchanger for heating purposes in the Patna region of India, using an experimental test rig. In the view of the author, real field experiments have several limitations such as lack of repeatability and uncontrolled conditions. It also takes more time for the response of parameters that depends on nature and climate. Moreover, earth-to-air heat exchangers may be expensive to fabricate and require more land area. Thus, in this work authors executed their experimental work in indoor controllable environments to investigate the thermal performance of an earth-to-air heat exchanger. The actual soil conditions were created and maintained the temperature at 26˚C throughout the soil in the vicinity of pipes. Three horizontal PVC pipes of equal lengths and diameters of 0.0285 m, 0.038 m and 0.0485 m were installed in the test rig. The experiments were performed for different inlet air velocities at ambient air temperature. This study acknowledges that the maximum rise in outlet temperature occurs at a lower speed for smaller pipes. Also, the maximum effectiveness of 0.83 was observed at 2 m/s for the smallest diameter pipe.
Go to article

Bibliography

[1] Uddin M.S., Ahmed R., Rahman M.: Performance evaluation and life cycle analysis of earth to air heat exchanger in a developing country. Energy Build. 128(2016), 254–261.
[2] Yusof T.M., Anuar S., Ibrahim H.: A review of ground heat exchangers for cooling application in the Malaysian climate. J. Mech. Eng. Sci. 8(2015), 1426–1439.
[3] Bisoniya T.S., Kumar A., Baredar P.: Heating potential evaluation of earth-air heat exchanger system for winter season. J. Build. Phys. 39(2015), 3, 242–260.
[4] Sehli A., Hasni A., Tamali M.: The potential of earth-air heat exchangers for low energy cooling of buildings in South Algeria. Energy Proced. 18(2012), 496–506.
[5] D’Agostino D., Marino C., Minichiello F.: Earth-to-air versus air-to-air heat exchangers: A numerical study on the energetic, economic, and environmental performances for Italian office buildings. Heat Transf. Eng. 41(2020), 12, 1040–1051.
[6] Benrachi N., Ouzzane M., Smaili A., Lamarche L., Badache M., Maref W.: Numerical parametric study of a new earth-air heat exchanger configuration designed for hot and arid climates. Int. J. Green Energy 17(2020), 2, 115–126.
[7] Abbaspour-Fard M.H., Gholami A., Khojastehpour M.: Evaluation of an earth-to-air heat exchanger for the north-east of Iran with semi-arid climate. Int. J. Green Energy 8(2011), 4, 499–510.
[8] Lin J., Nowamooz H., Braymand S.,Wolff P., Fond C.: Impact of soil moisture on the long-term energy performance of an earth-air heat exchanger system. Renew. Energy 147(2018), 2, 2676–2687.
[9] Agrawal K.K., Yadav T., Misra R., Agrawal G.D.: Effect of soil moisture contents on thermal performance of earth-air-pipe heat exchanger for winter heating in arid climate: In situ measurement. Geothermics 77 (2019), 12–23
[10] Abu-Hamdeh N.H.: Thermal properties of soils as affected by density and water content. Biosyst. Eng. 86(2003), 1, 97–102.
[11] Balghouthi M., Kooli S., Farhat A., Daghari H., Belghith A.: Experimental investigation of thermal and moisture behaviors of wet and dry soils with buried capillary heating system. Sol. Energy 79(2005), 6, 669–681.
[12] Mihalakakou G., Santamouris M., Asimakopoulos D.: Use of the ground for heat dissipation. Energy. 19(1994), 17–25.
[13] Gan G.: Simulation of dynamic interactions of the earth–air heat exchanger with soil and atmosphere for preheating of ventilation air. Appl. Energy 158(2015), 118–132.
[14] Abu-Hamdeh N.H., Reederb R.C.: Soil thermal conductivity effects of density, moisture, salt concentration, and organic matter. Soil Sci. Soc. Am. J. 64(2000), 1285–1290.
[15] Mei V.C.: Effect of backfilling material on ground coil performance. In: Proc. Ann. meeting of the ASHRAE, Nashville, 28 Jun, 1987, Oak Ridge Nat. Lab. 1987.
[16] Shojaee S.M.N., Malek K.: Earth-to-air heat exchangers cooling evaluation for different climates of Iran. Sustain. Energy Technol. Assess. 23(2017), 111–120.
[17] Mathur A., Srivastava A., Agrawal G.D., Mathur S., Mathur J.: CFD analysis of EATHE system under transient conditions for intermittent operation. Energy Build. 87(2015), 37–44.
[18] Serageldin A.A., Abdelrahman A.K., Ookawara S.: Earth-air heat exchanger thermal performance in Egyptian conditions: experimental results, mathematical model, and computational fluid dynamics simulation. Energy Convers. Manage. 122(2016), 25–38.
[19] Ahmad Sn., Prakash O.: Optimization of earth air tube heat exchanger for cooling application using Taguchi technique. Int. J. Heat Technol. 38(2020), 4, 854–862.
[20] Vargas J.V.C., Ordonez. J.C., Zamfirescu C., Campos M.C., Bejan A.: Optimal ground tube length for cooling of electronics shelters. Heat Transf. Eng. 26(2005), 10, 8–20.
[21] Ahmad S.N., Prakash O.: Optimization of ground heat exchanger of the ground source heat pump system based on exergetic analysis using Taguchi technique. Proc. Inst. Mech. Eng. C. J. Mech. Eng. Sci. 235(2021), 21, 5892–5901.
[22] Gao J., Li A., Xu X., Gang W., Yan T.: Ground heat exchangers: Applications, technology integration and potentials for zero energy buildings. Renew. Energy 128(2018), 337–349.
[23] Ahmad S.N., Prakash O.: A review on pre-installing investigations of earth air tube heat exchanger (EATHE). In Advances in Industrial Automation and Smart Manufacturing (A. Arockiarajan, M. Duraiselvam, Ramesh Raju, Eds.). Springer, Singapore 2020, 225–232.
[24] Yassine B., Ghali K., Ghaddar N., Chehab G., Srour I.: Effectiveness of the earth tube heat exchanger system coupled to a space model in achieving thermal comfort in rural areas. Int. J. Sustain. Energy 33(2014), 3, 567–586.
[25] Qi D., Li S., Zhao C., Xie W., Li A.: Structural optimization of multi-pipe earth to air heat exchanger in greenhouse. Geothermics 98(2022), 102288.
[26] Amanowicz A.: Influence of geometrical parameters on the flow characterictics of multi-pipe earth-to-air heat exchangers- experimental and CFD investigations. Appl. Energy 226(2018), 849–861.
[27] Amanowicz L., Wojtkowiak J.: Comparison of single- and multipipe earth-to-air heat exchangers in terms of energy gains and electricity consumption: A case study for the temperate climate of central europe. Energies 14(2021), 8217, 1–28.
[28] Hasan M.I., Noori S.W., Shkarah A.J.: Parametric study on the performance of the earth to air heat exchanger for cooling and heating applications. Heat Transf. – Asian Res. 48(2019), 4, 1805–1829.
[29] Wu H., Wang S., Zhu D.: Modelling and evaluation of cooling capacity of earthair- pipe systems. Energy Convers. Manage. 48(2007), 1462–1471.
[30] Ghosal M.K., Tiwari G.N.: Modeling and parametric studies for thermal performance of an earth to air heat exchanger integrated with a greenhouse. Energy Convers. Manage. 47(2006), 1779–1798.
[31] Ahmed S.F., Amanullah M.T.O., Khan M.M.K., Rasul M., Hassan N.M.S.: Parametric study on thermal performance of horizontal earth pipe cooling system in summer. Energy Convers. Manage. 114(2016), 324–337. [32] Singh B., Kumar R., Asati A.K.: Influence of parameters on performance of Earth-to-air heat exchanger in hot-dry climate. J. Mech. Sci. Technol. 32(2018), 5457–5463.
[33] Liu Z., Yu Z., Yang T., Roccamena L., Sun P., Li S., Zhang G., Mankibi M.: Numerical modeling and parametric study of a vertical earth-to-air heat exchanger system. Energy 172(2019), 220–231.
[34] Hasan M.I., Noori S.W.: Study the potential of using Earth to air heat exchanger for cooling and heating of the residential buildings in Iraq. Heat Transf. – Asian Res. 48(2019), 9, 1–26.
[35] Ahmad S.N., Prakash O.: Earth air tube heat exchanger - A parametric study. In: Theoretical, Computational, and Experimental Solutions to Thermo-Fluid Systems (M. Palanisamy, V. Ramalingam, M. Sivalingam, Eds.), Lecture Notes in Mechanical Engineering. Springer 2021, 53–62.
[36] Amanowicz L., Wojtkowiak J.: Thermal performance of multi-pipe earth-to-air heat exchangers considering the non-uniform distribution of air between parallel pipes. Geothermics 88(2020), 1–11.
[37] Amanowicz L., Wojtkowiak J.: Approximated flow characteristics of multi-pipe earth-to-air heat exchangers for thermal analysis under variable airflow conditions. Renew. Energy 158(2020), 585–597.
[38] Sakhri N., Menni Y., Chamkha A.J., Lorenzini G., Ameur H., Kaid N., Bensafi M.: Experimental study of an earth-to-air heat exchanger coupled to the solar chimney for heating and cooling applications in arid regions. J. Therm. Anal. Calorim. 145(2020), 3, 1–10.
[39] Chel A., Tiwari G.: Stand-alone photovoltaic (PV) integrated with earth to air heat exchanger (eahe) for space heating/cooling of adobe house in New Delhi (India). Energy Convers. Manage. 51(2010), 393–409.
[40] Li H., Yu Y., Niu F., Shafik M., Chen B.: Performance of a coupled cooling system with earth-to-air heat exchanger and solar chimney. Renew. Energy 62(2014), 468–77.
[41] Maerefat M., Haghighi A.: Passive cooling of buildings by using integrated earth to air heat exchanger and solar chimney. Renew. Energy 35(2010), 2316–24.
[42] Singh B, Asati A., Kumar R.: Evaluation of the cooling potential of earth-to-air heat exchanger using concrete pipes. Int. J. Thermophys. 42(2021), 2, 1–19.
[43] Lee K.H., Strand R.K.: The cooling and heating potential of an earth tube system in buildings. Energy Build. 40(2008), 486–494.
[44] Zhao Y., Li R., Ji C., Huan C., Zhang B., Liu L.: Parametric study and design of an earth-to-air heat exchanger using model experiment for memorial heating and cooling. Appl. Therm. Eng. 148(2019), 838–845.
[45] Rosa N., Soares N., Costa J.J., Santos P., Gervasio H.: Assessment of an earth-air heat exchanger (EAHE) system for residential buildings in warm summer Mediterranean climate. Sustain. Energy Technol. Assess. 38(2020), 1–11.
[46] Misra A.K., Gupta M., Lather M., Garg H.: Design and performance evaluation of low-cost Earth to air heat exchanger model suitable for small buildings in arid and semi-arid regions. KSCE J. Civ. Eng. 19(2015), 4, 853–856.
[47] Yoon S., Lee S.R., Go G.H.: Evaluation of thermal efficiency in different types of horizontal ground heat exchangers. Energy Build. 105(2015), 100–105.
[48] Molcrette V.F.A., Autier V.R.B.: New expression to calculate quantity of recovered heat in the earth-pipe-air heat-exchanger operating in winter heating mode. Arch. Thermodyn. 41(2020), 2, 103–117
[49] Yang W., Lu P., Chen Y.: Laboratory investigations of the thermal performance of an energy pile with spiral coil ground heat exchanger. Energy Build. 128(2016), 491–502.
[50] Elminshawy N.A.S., Siddiqui F.R., Farooq Q.U., Addas M.F.: Experimental investigation on the performance of earth-air pipe heat exchanger for different soil compaction levels. Appl. Therm. Eng. 124(2017), 1319–1327.
[51] Kim M.J., Lee S.R., Yoon S., Jeon J.S.: An applicable design method for horizontal spiral-coil-type ground heat exchangers. Geothermics 72(2018), 338–347.
[52] Yusof T.M., Ibrahim H., Azmi W.H., Rejab M.R.M.: Thermal analysis of earthto- air heat exchanger using laboratory simulator. Appl. Therm. Eng. 134(2018), 130–140.
[53] Agrawal K.K., Misra R., Agrawal G.D.: Improving the thermal performance of ground air heat exchanger system using sand-bentonite (in dry and wet condition) as backfilling material. Renew. Energy 146(2020), 2008–2023.
[54] Mazarron F.R., Cid-Falceto J., Canas I.: Ground thermal inertia for energy efficient building design: A case study on food industry. Energies 5(2012), 2, 227–242.
[55] Mihalakakou G., Santamouris M., Asimakopoulos D.: Modelling the thermal performance of earth-to-air heat exchangers. Sol. Energy 53(1994), 3, 301–305.
[56] Badescu V.: Simple and accurate model for the ground heat exchanger of a passive house. Renew. Energy 32(2007), 5, 845–855.
[57] Mathur A., Srivastava J., Mathur S., Agrawal G.D.: Transient effect of soil thermal diffusivity on performance of EATHE system. Energy Rep. 1(2015), 17–21.
[58] Zhang N., Wang Z.: Review of soil thermal conductivity and predictive models. Int. J. Therm. Sci. 117(2017), 172–183.
[59] Holman J.P.: Experimental Methods for Engineers (8th Edn.). Tata McGraw-Hill, New York 2007.
[60] Bansal V., Misra R., Agrawal G.D., Mathur J.: Performance analysis of earthpipe- air heat exchanger for winter heating. Energy Build. 41(2009), 11, 1151–1154.
Go to article

Authors and Affiliations

Saif Nawaz Ahmad
1
Om Prakash
1

  1. National Institute of Technology Patna, Bihar 800005, India

Instructions for authors

Archives of Thermodynamics publishes original papers which have not previously appeared in other journals. The journal does not have article processing charges (APCs) nor article submission charges. The language of the papers is English. The paper should not exceed the length of 25 pages. All pages should be numbered. The plan and form of the papers should be as follows:

1. The heading should specify the title (as short as possible), author, his/her complete affiliation, town, zip code, country and e-mail. Please indicate the corresponding author. The heading should be followed by Abstract of maximum 15 typewritten lines and Keywords.

2. More important symbols used in the paper can be listed in Nomenclature, placed below Abstract and arranged in a column, e.g.:
u – velocity, m/s
v – specific volume, m/kg etc.
The list should begin with Latin symbols in alphabetical order followed by Greek symbols also in alphabetical order and with a separate heading. Subscripts and superscripts should follow Greek symbols and should be identified with separate headings. Physical quantities should be expressed in SI units ( Système International d’Unités).

3. All abbreviations should be spelled out first time they are introduced in the text.

4. The equations should be each in a separate line. Standard mathematical notation should be used. All symbols used in equations must be clearly defined. The numbers of equations should run consecutively, irrespective of the division of the paper into sections. The numbers should be given in round brackets on the righthand side of the page.

5. Particular attention should be paid to the differentiation between capital and small letters. If there is a risk of confusion, the symbols should be explained (for example small c) in the margins. Indices of more than one level (such as Bfa) should be avoided wherever possible.

6. Computer-generated figures should be produced using bold lines and characters. No remarks should be written directly on the figures, except numerals or letter symbols only. Figures should be as small as possible while displaying clearly all the information requires, and with all lettering readable. The relevant explanations can be given in the caption.

7. The figures, including photographs, diagrams, etc., should be numbered with Arabic numerals in the same order in which they appear in the text. Each figure should have its own caption explaining the content without reference to the text.

8. Computer files on an enclosed disc or sent by e-mail to the Editorial Office are welcome. The manuscript should be written as a MS Word file – ∗.doc, ∗.docx or LATEX file – ∗.tex. For revised manuscripts after peer review process, figures should be submitted as separate graphic files in either vector formats (PostScript (PS), Encapsulated PostScript (EPS), preferable, CorelDraw (CDR), etc.) or bitmap formats (Tagged Image File Format (TIFF), Joint Photographic Experts Group (JPEG), etc.), with the resolution not lower than 300 dpi, preferably 600 dpi. These resolutions refer to images sized at dimensions comparable to those of figures in the print journal. Therefore, electronic figures should be sized to fit on single printed page and can have maximum 120 mm x 170 mm. Figures created in MS World, Exel, or PowerPoint will not be accepted. The quality of images downloaded from websites and the Internet are also not acceptable, because of their low resolution (usually only 72 dpi), inadequate for print reproduction.

9. The references for the paper should be numbered in the order in which they are called in the text. Calling the references is by giving the appropriate numbers in square brackets. The references should be listed with the following information provided: the author’s surname and the initials of his/her names, the complete title of the work (in English translation) and, in addition:

(a) for books: the publishing house and the place and year of publication, for example:
[1] Holman J.P.: Heat Transfer. McGraw-Hill, New York 1968.

(b) for journals: the name of the journal, volume (Arabic numerals in bold), year of publication (in round brackets), number and, if appropriate, numbers of relevant pages, for example:
[2] Rizzo F.I., Shippy D.I.: A method of solution for certain problems of transient heat conduction . AIAA J. 8(1970), No. 11, 2004–2009.

For works originally published in a language other than English, the language should be indicated in parentheses at the end of the reference.

Authors are responsible for ensuring that the information in each reference is complete and accurate.

10. As the papers are published in English, the authors who are not native speakers of English are obliged to have the paper thoroughly reviewed language-wise before submitting for publication.


Manuscript submission

Manuscripts to be considered for publication should be electronically submitted to the Editorial Office via the online submission and reviewing system, the Editorial System, at http://www.editorialsystem.com/aot. Submission to the journal proceeds totally on line and you will be guided stepwise throughout the process of the creation and uploading of your files. The body of the text, tables and figures, along with captions for figures and tables should be submitted separately. The system automatically converts source files to a single PDF file article, for subsequent approval by the corresponding Author, which is then used in the peer-review process. All correspondence, including notification confirming the submission of the manuscripts to the Editorial Office, notification of the Editorsñs decision and requests for revision, takes place by e-mails. Authors should designate the corresponding author, whose responsibility is to represent the Authors in contacts with the Editorial Office. Authors are requested not to submit the manuscripts by post or e-mail.
The illustrations may be submitted in color, however they will be printed in black and white in the journal, so the grayscale contributions are preferable. Therefore, the figure caption and the entire text of the paper should not make any reference to color in the illustration. Moreover the illustration should effectively convey author’s intended meaning when it is printed as a halftone. The illustrations will be reproduced in color in the online publication.


Further information

All manuscripts will undergo some editorial modification. The paper proofs (as PDF file) will be sent by e-mail to the corresponding author for acceptance, and should be returned within two weeks of receipt. Within the proofs corrections of minor and typographical errors in: author names, affiliations, articles titles, abstracts and keywords, formulas, symbols, grammatical error, details in figures, etc., are only allowed, as well as necessary small additions. The changes within the text will be accepted in case of serious errors, for example with regard to scientific accuracy, or if authors reputation and that of the journal would be affected. Submitted material will not be returned to the author, unless specifically requested. A PDF file of published paper will be supplied free of charge to the Corresponding Author. Submission of the manuscript expresses at the same time the authors consent to its publishing in both printed and electronic versions.


Transfer of Copyright Agreement

Submission of the manuscript means that the authors automatically agree to assign the copyright to the Publisher. Once a paper has been accepted for publication, as a condition of publication, the authors are asked to send by email a scanned copy of the signed original of the Transfer of Copyright Agreement, signed by the Corresponding Author on behalf of all authors to the Managing Editor of the Journal. The copyright form can be downloaded from the journal’s website at http://www.imp.gda.pl/archives-of-thermodynamics/ under Notes for Contributors.

This page uses 'cookies'. Learn more