Tytuł artykułu

The Effect of Water Mist Cooling of Casting Die on the Solidification, Microstructure and Properties of AlSi20 Alloy

Tytuł czasopisma

Archives of Metallurgy and Materials




vol. 62


No 1


Wydział PAN

Nauki Techniczne


Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences




DOI: 10.1515/amm-2017-0026 ; e-ISSN 2300-1909


Archives of Metallurgy and Materials; 2017; vol. 62; No 1


Xu (2014), Influence of pressure and surface roughness on the heat transfer efficiency during water spray quenching of aluminum alloy, Mater Process Technol, 214. ; Władysiak (2013), Computer Control the Cooling Process in Permanent Mold Casting of Al Si Alloy, Arch Metall Mater, 58, 10, ; Duggan (2015), Modelling the creation and destruction of columnar and equiaxed zones during solidification and melting in multi - pass welding of steel, Comput Mater Sci, 97. ; Władysiak (2010), Effect of water mist on cooling process of casting die and microstructure of alsi alloy, Arch Metall Mater, 11, 93. ; Yamagata (2008), Thermal and metallographic characteristics of the Si high - pressure die - casting alloy for monolithic cylinder blocks, Mater Process Technol, 20, 199. ; Nowak (6082), Water - Air Spray Cooling of Extruded Profiles : Process Integrated Heat Treatment of the Alloy EN, Mater Eng Perform, 22, 2580, ; Rapiejko (2014), Effect Of Cr and V Alloy Additions on the Microstructure and Mechanical Properties of Am Magnesium Alloy, Arch Metall Mater, 60, 10. ; Heusler (2002), and Influence of alloying elements on the thermal analysis results of Al - Si cast alloys Feb, Light Met, 2, 17, ; Raghukiran (2015), Effect of scandium addition on the microstructure mechanical and wear properties of the spray formed hypereutectic aluminum - silicon alloys, Mater Sci Eng, 641. ; Yamagata (2008), The effect of average cooling rates on the microstructure of the Si high pressure die casting alloy used for monolithic cylinder blocks, Mater Process Technol, 20, 203. ; Kang (2015), Intensive riser cooling of castings after solidification, Mater Process Technol, 215. ; Karpe (2013), The influence of Si and V on the kinetics of phase transformation and microstructure of rapidly solidified Zr alloys, Min Metall Sect B Metall, 49, 83, ; Shabestari (2005), Thermal analysis study of the effect of the cooling rate on the microstructure and solidification parameters of aluminum alloy, Can Metall, 44, 305, ; Bamberger (1986), and Some observations on dendritic arm spacing in Mg and Al - Cu alloy chill castings, Mater Sci, 21, 2781, ; Kaya (2007), Dendritic Growth in an Aluminum - Silicon Alloy, Mater Eng Perform, 16, 12, ; Władysiak (2014), Effect of Water Mist Cooling on Microstructure of Hypereutectic Si Alloy, Arch Foundry Eng, 14, 117, ; Hejazi (2010), A Cu - Cr alloy with nano and microscale Cr particles produced in a water - cooled copper mold, Int J Miner Metall Mater, 17, 629, ; Wang (2014), Development and evaluation of a new rapid mold heating and cooling method for rapid heat cycle molding, Int J Heat Mass Transf, 78. ; Pillai (2004), A simple inexpensive technique for enhancing density and mechanical properties of Al - Si alloys, Mater Process Technol, 146, 338, ; Jones (1996), Cooling rates during rapid solidification from a chill surface, Mater Lett, 26, 133, ; Chen (1998), Dendrite coarsening during directional solidification of alloys, Mater Sci Eng, 247. ; Kubiak (2011), Surface morphology in engineering applications : Influence of roughness on sliding and wear in dry fretting, Int, 44, 1427. ; Uzun (2004), Hardness and microstructural characteristics of rapidly solidified wt Si alloys, Alloys Compd, 8, 376. ; Zhu (2014), Microstructure evolution of spray - formed hypereutectic Al - Si alloys in semisolid reheating process China, Trans Nonferrous Met Soc, 24, 1766,