This paper presents a numerical investigation of the effects of lamination orientation on the fracture behaviour of rectangular steel wires for civil engineering applications using finite element (FE) analysis. The presence of mid-thickness across-the-width lamination changes the cup and cone fracture shape exhibited by the lamination-free wire to a V-shaped fracture with an opening at the bottom/pointed end of the V-shape at the mid-thickness across-the-width lamination location. The presence of mid-width across-the-thickness lamination changes the cup and cone fracture shape of the lamination-free wire without an opening to a cup and cone fracture shape with an opening at the lamination location. The FE fracture behaviour prediction approach adopted in this work provides an understanding of the effects of lamination orientation on the fracture behaviour of wires for civil engineering applications which cannot be understood through experimental investigations because it is impossible to machine laminations in different orientations into wire specimens.

The article presents a precise method for the orientation process of NiMnGa-based single crystals. For this method, a scanning electron microscope equipped with an EBSD camera and a heating stage allowing temperatures exceeding 873 K was used. The orientation process was carried out in both the high-temperature austenite phase and in the room-temperature martensite phase. The facilities allowed for determining the orientation of a single grain of austenite at elevated temperatures as well as the orientation of particular martensitic variants at room temperature. A practically perfect cubic orientation was obtained in the austenitic case with a deviation of about 1° while the samples oriented in the martensitic phase deviated from the desired orientation by 4.5-5.2°. Additionally, the training process of single crystals was carried out in order to show the influence of the orientation process on twinning stress.

The discourse on homosexually has largely remained Euro-American with a focus on human right of African homosexuals residing in Africa. However, current debates in Africa have centered on the cultural acceptability, legality as well as mental health concerns presumed to be associated with homosexuality. The paper approaches the issue of homosexuality from a perspective that is sensitive to the cultural context of Ghana and also through a non-Euro-American lens. The author attempts to address some of the misunderstanding about the legal status of homosexuals and the negative attitudes in Ghana. The paper concludes that Ghanaians face a paradox of accepting homosexuality because it cannot be understood to further growth of human society from their perspective. Similarly, if Ghanaians view homosexuality as a mental health issue, then it is more appropriate to decriminalize it as it is not appropriate to criminalize mental disorders. Reconceptualizing the issue as a human rights one in which both anti- and pro-homosexual religious and sexual rights respectively are accommodated may be more progressive than promoting one set of rights at the expense of the other. Though Ghana is the focus of this paper, it is believed that the discussions presented are applicable to the rest of Africa and other non-Western societies.

Twinned dendrites in Al-Zn alloy with high Zn content (40% wt.%) were successfully prepared by directional solidification. At different directional solidification rates (1000 and 1500 μm/s), microstructures and growth orientation variations of Al twinned dendrite and non-twinned dendrite were characterized. By using the inverted trapezoidal graphite sleeve at 1000 μm/s, Al twinned dendrite were formed to developed feather crystal structures in longitudinal section. Its primary and secondary twinned dendrite were grew along [110] direction. Moreover the deviation angle between [110] direction of Al twinned dendrite and the heat flow direction was about 27.15°. While not using the inverted trapezoidal graphite sleeve at 1000 and 1500 μm/s, Al dendrite was the non-twinned dendrite and the twinned dendrite was not appeared. The experimental results showed that the higher temperature gradient, a certain pulling rate and convection environment were the formation conditions of twinned dendrites.

Palaeostresses inferred from brittle mesostructures in the southern Wright Peninsula show a stress field characterized by compressional, strike−slip and extensional regime stress states. The compressional stress ( s 1 ) shows a main NW−SE direction and the extensional stress ( s 3 ) shows a relative scattering with two main modes: NE−SW to E−W and NW−SE. The maximum horizontal stress ( s y ) has a bimodal distribution with NW−SE and NE−SW direction. The compressional orientation is related to subduction of the former Phoenix Plate under the Antarctic Plate from the Early Jurassic to the Early Miocene. Extensional structures within a broad−scale compressional stress field can be related to both the decrease in relative stress magnitudes from active margins to intraplate regions and stretching processes occurring in eastern Adelaide Island, which develop a fore−arc or intra−arc basin from the Early Miocene. Stress states with NW−SE−trending s 1 are compatible with the dominant pattern established for the western Antarctic Peninsula. NW−SE orientations of s 3 suggest the occurrence of tectonic forces coming from fore−arc extension along the western Antarctic Peninsula.

The article is devoted to the establishment, development and activity of the Committee of Oriental Studies of the Polish Academy of Sciences, which has been operating under various names since 1952 and celebrates its 70th anniversary this year. The Committee is the most important institution of Oriental studies in Poland, coordinating and monitoring the development of various fields of this area of science. It also conducts organizational activities (conferences, symposia, conventions) and publishing – among others it is the publisher of the oldest Polish scientific journal in this field, Rocznik Orientalistyczny / Yearbook of Oriental Studies and various publishing series.

This paper presents results of object-oriented classification of Landsat ETM+ satellite im-age conducted using eCognition software. The classified image was acquired on 7 May 2000. In this particular study, an area of 423 km2 within the borders of Legionowo Community near Warsaw is considered.

Prior to classification, segmentation of the Landsat ETM+ image is performed using panchro-matic channel, fused multispectral and panchromatic data. The applied methods of classification en-abled the identification of 18 land cover and land use classes. After the classification, generalization and raster to vector conversion, verification and accuracy assessment are performed by means of vis-ual interpretation. Overall accuracy of the classification reached 94.6%. The verification and classifi-cation results are combined to form the final database.

This is followed by comparing the object-oriented with traditional pixel-based classification. The latter is performed using the so-called hybrid classification based on both supervised and unsuper-vised classification approaches. The traditional pixel-based approach identified only 8 classes. Com-parison of the pixel-based classification with the database obtained using the object-oriented ap-proach revealed that the former reached 72% and 61% accuracy, according to the applied method.

The article deals with the appropriation of postcolonial studies to look at Central Europe and Galicia. Beginning with the concept of“internal colonialism“, we follow the evolution of postcolonial theory from a basically economy-based concept into a poststructuralist cultural theory, presenting the development and uses of its central concepts, such as Orientalism or othering. Based on some examples, we also highlight its previous appropriation to Central Europe and the political implications it carries in this region.

17 November 2022 marks the centenary of the death of Jan Grzegorzewski – Orientalist, Slavist, publicist and social activist. The aim of this article is to highlight this figure and to show his activity in various areas of social and scientific life, especially his contribution to Polish Oriental studies. This somewhat forgotten but extremely interesting and colourful, although somewhat controversial, figure has still not received the comprehensive biographical treatment he fully deserves. Thanks to his extraordinary determination and commitment to his activities, Jan Grzegorzewski initiated the establishing of the first Polish scientific journal of Oriental studies, Rocznik Orientalistyczny, for which he also obtained funds. The first part of the first volume of Rocznik, covering the years 1914–1915, was published in 1915 in Cracow, and the second part (for the years 1916–1918) only in 1918. There is also no doubt that with his activities, both academic and journalistic, Jan Grzegorzewski contributed to the establishment of the first Polish Oriental studies in Poland, which took place in 1919 at the Jagiellonian University in Cracow. Analysing some of Grzegorzewski’s achievements from today’s perspective, one can venture to say that with the issues presented in his publications, he undoubtedly inspired many later Orientalists to set new research directions.

Professor Tadeusz Kowalski (1889–1948) was in correspondence with scholars from practically all over the world. He had an active interest in the developments of Oriental studies in the Soviet Union. He valued the publications he received from the USSR as well as all contacts he had with Russian researchers. He sought to cooperate with Alexander Samoylovich (1880–1938) – one of the most eminent Turkologists in the Soviet Union. This goal had been partially achieved. The archives of the Polish Academy of Sciences and the Polish Academy of Arts and Sciences in Kraków now hold, catalogued under ref. no. K III-4, j. 174, just three letters from the Russian Turkologist. These materials, despite their small number, are an engrossing source of knowledge on the state of Soviet Turkish studies in the mid-1920s and the Soviet Oriental studies community. As the author managed to determine, these letters are all the more precious as the branch of the archives at the Russian Academy of Sciences in St.-Petersburg, where the legacy of professor Samoylovich is kept, has no copies. Interestingly, there are no surviving copies of the letters from professor Kowalski to the Russian Turkologist. This article aims to analyse the contents of the letters written by Alexander Samoylovich, the Soviet Turkologist, to professor Tadeusz Kowalski, and determine the purpose and direction in which Turkish studies were developing in the USSR in the period described in these sources.

The article describes the process of creating 3D models of architectural objects on the basis of video images, which had been acquired by a Sony NEX-VG10E fixed focal length video camera. It was assumed, that based on video and Terrestrial Laser Scanning data it is possible to develop 3D models of architectural objects. The acquisition of video data was preceded by the calibration of video camera. The process of creating 3D models from video data involves the following steps: video frames selection for the orientation process, orientation of video frames using points with known coordinates from Terrestrial Laser Scanning (TLS), generating a TIN model using automatic matching methods. The above objects have been measured with an impulse laser scanner, Leica ScanStation 2. Created 3D models of architectural objects were compared with 3D models of the same objects for which the self-calibration bundle adjustment process was performed. In this order a PhotoModeler Software was used. In order to assess the accuracy of the developed 3D models of architectural objects, points with known coordinates from Terrestrial Laser Scanning were used. To assess the accuracy a shortest distance method was used. Analysis of the accuracy showed that 3D models generated from video images differ by about 0.06 ÷ 0.13 m compared to TLS data.

A particle-level simulation technique has been developed for modelling fibre suspension flow in a converging channel of a papermachine headbox. The fibre model is represented by a chain of elements connected together. The model was verified by the simulation of rigid fibre dynamics in a simple shear flow. The period of rotation was found to be in a very good agreement with theory and reference data. The model was then employed to simulate fibre motion in a converging channel of a papermachine headbox. Fibre suspension motion was resolved using two-step procedure. Velocity field was calculated by means of a commercial CFD code ANSYS Fluent with RSM turbulence model applied and used as an input to the in-house code allowing to simulate fibre dynamics. Results of the calculations were used to construct the fibre orientation probability distribution (FOPD) which was found to be consistent with available experimental data.

Rare earth Nd-Fe-B, a widely used magnet composition, was synthesized in a shape of powders using gas atomization, a rapid solidification based process. The microstructure and properties were investigated in accordance with solidification rate and densification. Detailed microstructural characterization was performed by using scanning electron microscope (SEM) and the structural properties were measured by using X-ray diffraction. Iron in the form of α-Fe phase was observed in powder of about 30 μm. It was expected that fraction of Nd2Fe14B phase increased rapidly with decrease in powder size, on the other hand that of α-Fe phase was decreased. Nd-rich phase diffused from grain boundary to particle boundary after hot deformation due to capillary action. The coercivity of the alloy decreased with increase in powder size. After hot deformation, Nd2Fe14B phase tend to align to c-axis.

Understanding the factors that influence the quality of unmanned aerial vehicle (UAV)-based products is

a scientifically ongoing and relevant topic. Our research focused on the impact of the interior orientation

parameters (IOPs) on the positional accuracy of points in a calibration field, identified and measured in an

orthophoto and a point cloud. We established a calibration field consisting of 20 materialized points and

10 detailed points measured with high accuracy. Surveying missions with a fixed-wing UAV were carried

out in three series. Several image blocks that differed in flight direction (along, across), flight altitude

(70 m, 120 m), and IOPs (known or unknown values in the image-block adjustment) were composed. The

analysis of the various scenarios indicated that fixed IOPs, computed from a good geometric composition,

can especially improve vertical accuracy in comparison with self-calibration; an image block composed

from two perpendicular flight directions can yield better results than an image block composed from a single

flight direction.

In the article the author discusses the relationship between education and socio-cultural needs. The socio – cultural reality is the reality of a permanent change. It is difficult to describe and even more difficult to understand. The specific character of qualitatively new changes in the relations between globality and locality implies a completely new perception of reality, ways of interpreting the world, and a new quality of judgments about the condition of the modern man. This reality is also a ”multiplicity of worlds”, which means a large number of possibilities to create oneself. What individuals perceive as their ”own” has the biggest developmental potential when it is worked out on the proactivity path. proactive people are distinguished by interrelated features: the search for a possibility of change (the environment examination, going beyond limitations of a given situation), establishing effective and change oriented goals (opening new paths of action), foreseeing problems and remedia measures (the analysis of one’s own achievements, looking for signals of threats or dangers), looking for new ways of achieving goals (the ambition is to make a new tradition).

Hope is often treated as a priceless human value anchored in goal-related cognitions. The experiment aimed to investigate whether current hopeful thinking is related to problem-solving performance and how induced goal-oriented thinking influences this problem-solving process. Participants (N = 410) were asked to recall and describe their successful or unsuccessful goal pursuit and complete a scale assessing current hopeful thinking. Subsequently, participants were instructed to (1) think about actions that would be taken to solve the societal problem (i.e., an insufficient number of volunteers in Social Welfare Centers) and (2) describe these actions. In general, people who recalled successful events felt more hopeful than those who recalled unsuccessful events. State Hope was positively correlated with both the quantity (i.e., the total number of solutions) and quality (i.e., usefulness) of participants’ offered solutions. No interaction between State Hope and type of conditions with solution quantity or solution quality was found. State hope, however, interacted with the type of recalled goal pursuit when sex differences were considered. More hopeful women had a better solution quality when they recalled an unsuccessful goal pursuit. For men, a similar pattern was found when they recalled a successful goal pursuit. Lastly, the findings were discussed in light of Snyder’s Theory of Hope.

The study considers remittances as part of the lifeworlds of immigrants in multiple interactions with return intentions and communication with those left behind. This is an alternative view of the standard approach to remittances as a possible source of development or as a variable to be explained by family solidarity, investment projects or the reasons for return. The key dependent variable is the home orien-tation of immigrants as a function of remittances, return intentions and communication behaviours, measured in quantitative and typological terms. The typological analysis of home orientation diverges from the standard approach, which is in terms of high or low intensity of cross-border activities of remitting or communicating between immigrants and those they have left behind. It argues for the fact that cross-border activities combine in different ways to generate specific social types of remitting prac-tices. The remitting behaviours of migrants are, in our approach, multidimensional, encompassing eco-nomic, social and cultural content. Three hypotheses are formulated on: 1) collective deprivation in remitting money; 2) survival–development–identification strategies of migrants’ families; and 3) higher predictability of home orientation compared to economic remitting behaviours. In this context, higher predictability means greater variation of the synthetic variable of home orientation by social, cultural and economic factors as compared to the impact of the same factors on the more abstract variable of economic remittances.

The article presents the results of research on the development of a method for improving the positioning accuracy of an UAV equipped with a single-frequency GPS receiver for determining the linear elements of exterior orientation in aerial photogrammetry. Thus, the paper presents a computational strategy for improving UAV position determination using the SPP code method and the products of the IGS service. The developed algorithmswere tested in two independent research experiments performed with theUAVplatform on which an AsteRx-m2 UAS single-frequency receiver was installed. As a result of the experiments, it was shown that the use of IGS products in the SPP code method made it possible to improve the accuracy of the linear elements to the level of about ±2.088 m for X coordinate, ±1.547 m for Y coordinate, ±3.712 m for Z coordinate. The paper also shows the trend of changes in the obtained accuracy in determining linear elements of exterior orientation in the form of a linear regression function. Finally, the paper also applies the SBAS corrections model for the improvement of UAV position calculation and determination of linear elements of exterior orientation. In this case, the improvement in the accuracy of determining the linear elements of exterior orientation is about ±1.843 m for X coordinate, ±1.658 m for Y coordinate, ±7.930 m for Z coordinate. As the obtained test results show, the use of IGS products and SBAS corrections in the SPP code method makes it possible to improve the determination ofUAVpositions for the use in aerial photogrammetry. Keywords: UAV, GNSS measurements, linear elements of exterior orientation, accuracy.

The main goal of estimating models for industrial applications is to guarantee the cheapest system identification. The requirements for the identification experiment should not be allowed to affect product quality under normal operating conditions. This paper deals with ensuring the required liquid levels of the cascade system tanks using the model predictive control (MPC) method. The MPC strategy was extended with the Kalman filter (KF) to predict the system’s succeeding states subject to a reference trajectory in the presence of both process and measurement noise covariances. The main contribution is to use the application-oriented input design to update the parameters of the model during system degradation. This framework delivers the least-costly identification experiment and guarantees high performance of the system with the updated model. The methods presented are evaluated both in the experiments on a real process and in the computer simulations. The results of the robust MPC application for cascade system water levels control are discussed.

In this paper deep neural networks are proposed to diagnose inter-turn short-circuits of induction motor stator windings operating under the Direct Field Oriented Control method. A convolutional neural network (CNN), trained with a Stochastic Gradient Descent with Momentum method is used. This kind of deep-trained neural network allows to significantly accelerate the diagnostic process compared to the traditional methods based on the Fast Fourier Transform as well as it does not require stationary operating conditions. To assess the effectiveness of the applied CNN-based detectors, the tests were carried out for variable load conditions and different values of the supply voltage frequency. Experimental results of the proposed induction motor fault detection system are presented and discussed.

Orhan Pamuk, the winner of the Nobel Prize in Literature in 2006, is one of the most interesting and versatile of contemporary writers whose prose contributes to the understanding of the cultural background of the Orient and the Occident forged out of the juxtaposition of Islam and Christianity. As a might-have-been artist, who is currently an amateur photographer, the author, in an uncommon way, visualizes the continual wonder towards colors in the surrounding reality featuring in his fictional and non-fictional texts. The most important aspects of Pamuk’s works, however, are the journeys near and far and those within oneself, as well as the wanderings through cities, especially those of his native Istanbul. Aside from the returns home and to the motherland, Pamuk contrasts the inspiring voyages out with the voyages into the collective and individual past, in all their historical and political complexity. The present paper is an overview of Orhan Pamuk’s works from the perspective of colors and the aforesaid passages, which remind his readers of travelling as a basic topos of the course of human existence.

The paper examines Edward Said's critique of Thomas Edward Lawrence view on Arabs and Arabian culture and society. On the one hand some of Said's allegations seems poorly grounded and can be deny with some excerpts from Lawrence's Seven Pillars of Wisdom. On the other hand Said doesn't remark serious shortcomings of Lawrence's outlook of intercultural relations.

Fruit flies belonging to the Bactrocera dorsalis species complex pose a significant threat to mangoes and other crops in the Philippines and worldwide. Identifying cryptic species within this complex is challenging, particularly when relying solely on morphological analysis. In this study, we sequenced two fragments of the nuclear 18S and ITS2-28S rRNA genes from specimens of Bactrocera dorsalis Hendel collected in the Philippines to assess their applicability for species diagnostics. Subsequent sequencing and analysis revealed that the 18S and 28S rRNA gene fragments matched B. dorsalis sequences in NCBI but also displayed high similarity with other Bactrocera and insect species. On the other hand, sequences of the ITS2 segment showed hits specific to B. dorsalis. Further analysis of the 18S rRNA gene in fruit flies collected from various sources and host plants in the country suggests conserved sequences among Bactrocera samples, irrespective of collection site and host plant species. In conclusion, our findings suggest that, among the tested nuclear DNA fragments, only the ITS2 demonstrates sufficient species-level nucleotide variation for effective use as a molecular diagnostic marker for B. dorsalis identification.