Dr. Krzysztof Fic of the Poznań University of Technology discusses energy storage, aesthetic medicine’s quest for immortality, and how much time goes into being a scientist.
This paper presents a study on the effect of cleaning factors on the energy consumption of the cleaning process in a CIP system, and the correlation between single components of electricity necessary to perform this process and the cleanliness degree obtained. Studies were carried out in a laboratory cleaning station, wherein a plate heat exchanger contaminated with hot milk was included. The research program was developed according to a 5-level statistical plan. Based on the results, obtained with Experiment Planner 1.0, a regression function of energy requirement considering variables such as: cleaning time, temperature and flow rate of the cleaning liquid via the cleaned exchanger has been developed. Describing this relationship, linear and quadratic functions with double interactions were used. Significance level for the analysis was established at α = 0.05. Correlation analysis between components of the electricity necessary to perform the cleaning process (pump drive and heating of the cleaning agent) and the resulting degree of cleaning of heat exchanger plates was performed.
Mobile devices have become an integral part of our life and provide dozens of useful services to their users. However, usability of mobile devices is hindered by battery lifetime. Energy conservation can extend battery lifetime, however, any energy management policy requires accurate prediction of energy consumption, which is impossible without reliable energy measurement and estimation methods and tools. We present an analysis of the energy measurement methodologies and describe the implementations of the internal (profiling) software (proprietary, custom) and external software-based (Java API, Sensor API, GSM AT) energy measurement methodologies. The methods are applied to measure energy consumption on a variety of mobile devices (laptop PC, PDA, smart phone). A case study of measuring energy consumption on a mobile computer using 3DMark06 benchmarking software is presented
This paper proposes an analysis of the effect of vertical position of the pivot point of the inverted pendulum during humanoid walking. We introduce a new feature of the inverted pendulum by taking a pivot point under the ground level allowing a natural trajectory for the center of pressure (CoP), like in human walking. The influence of the vertical position of the pivot point on energy consumption is analyzed here. The evaluation of a 3D Walking gait is based on the energy consumption. A sthenic criterion is used to depict this evaluation. A consequent reduction of joint torques is shown with a pivot point under the ground.
This research presents a 3D FE method for the simulation of the variable reluctance stepper motor dynamics. The proposed model is used to obtain the optimal minimum energy control law that minimizes the energy injected by the controller. The method is based on the strong coupling of field - circuit equations and extended to eddy current, motion and nonlinearity problem. The linearization technique for the coupled problem is presented. Also the lamination of the motor core is considered. In the paper the open - loop control problem is analyzed. The proposed model is validated by the comparison with measurements. Next, to demonstrate the effectiveness of the proposed optimal minimum energy control method is applied. In both cases, the examination of the variable reluctance stepper motor dynamics and the steel loss in the core is presented and compared.
The aim of the research is to assess and discuss the diversity of energy production and consumption in European Union countries. The time scope covers the years 2007 and 2016. The diversity of EU countries was examined using the cluster analysis. The following diagnostic features were adopted for the analysis: energy dependency rate (in %), gross inland consumption of energy per 10,000 inhabitants (toe/10,000 inhabitants), primary production of energy (all products) per 10,000 inhabitants (toe/10,000 inhabitants), primary production of renewable energies per 10,000 inhabitants (toe/10,000 inhabitants), primary production of energy (without renewable energy) per 10,000 inhabitants (toe/10,000 inhabitants). Comparing the included indicators from 2016 to 2007 for all EU countries, an increase was recorded only for the primary production of renewable energies per 10,000 inhabitants,. Based on the cluster analysis, the examined countries were divided into six groups. According to the results of the research carried out, Northern and Eastern European countries are characterized by low energy dependence. However, according to the analysis carried out, this dependence is guaranteed based on various energy sources. The Scandinavian countries (Sweden, Finland) owe their high independence to the production of large amounts of energy from renewable sources. On the other hand, countries such as the Netherlands, Denmark, Estonia and the whole of Eastern Europe are based on primary energy sources such as: coal, oil and gas. Southern Europe countries (Greece, Spain, Italy, Portugal, Cyprus, Malta) are characterized by high energy dependence, as evidenced by low rates in the area of energy production, both in total and renewable and non-renewable energy production.
In this article, the authors propose and investigate a new concept of HAPS aerostat design in a modular form, which allows for sequential increasing or decreasing of the total volume, up to the desired size. In its initial form, the aerostat has relatively small dimensions but its central cylindrical part is multi-segmented and can be easily extended. The application of controllable construction couplings enables precise control of the aerostat expansion process and significantly improves its vertical mobility. The paper describes details of telescopic aerostat construction, presents a mathematical model of its vertical motion and investigates numerically two volume control strategies aimed at maximization of operation efficiency and minimization of operation cost. The results obtained reveal the main problems that have to be addressed and the factors that play a key role in design of such telescopic aerostats and control of their vertical mobility.
This paper presents the Life Cycle Assessment (LCA) analysis concerning the selected options of supercritical coal power units. The investigation covers a pulverized power unit without a CCS (Carbon Capture and Storage) installation, a pulverized unit with a "post-combustion" installation (MEA type) and a pulverized power unit working in the "oxy-combustion" mode. For each variant the net electric power amounts to 600 MW. The energy component of the LCA analysis has been determined. It describes the depletion of non-renewable natural resources. The energy component is determined by the coefficient of cumulative energy consumption in the life cycle. For the calculation of the ecological component of the LCA analysis the cumulative CO2 emission has been applied. At present it is the basic emission factor for the LCA analysis of power plants. The work also presents the sensitivity analysis of calculated energy and ecological factors.
Energy efficiency improvement and ecological safety of heat power plants are urgent problems, which require scientifically grounded approaches and solutions. These problems can be solved partly within the presented heat-and-power cycles by including contact energy exchange equipment in the circuits of existing installations. A significant positive effectis obtained in the contact energy exchange installations, such as gas-steam installation ‘Aquarius’ and the contact hydrogen heat generator that also can use hydrogen as a fuel. In these plants, the efficiency increases approximately by 10–12% in comparison with traditional installations, and the concentration of toxic substances, such as nitrogen oxides and carbon monoxide in flue gas can be reduced to 30 mg/m3and to 5 mg/m3, respectively. Moreover, the plants additionally ‘generate’ the clean water, which can be used for technical purposes.