The depletion of stocks of fossil fuels and the environment protection requirements increase the significance of hydrogen as a future energy carrier. The present research is focused on the development of new safe methods of production, transport and storage of hydrogen. The paper presents an analysis of problems related to the assessment of the effects of failure of hydrogen transporting pipelines. Scenarios of hazardous events connected with an uncontrollable leakage of hydrogen are discussed. The sizes of heat radiation and pressure wave hazard zones are determined.
The industrial grinding devices, which work in the high-energetic fluidized bed conditions make it possible to obtain guaranteed particle size distribution of product and decrease of consumption energy. The matrix model for transformation of particle size distribution in the fluidized bed opposed jet mill is presented in the part IV of article. The proposed model contains the mass population balance of particle equation, in which are block matrices: the matrix of circuit M, the matrix of inputs F and the matrix of feed F0. The matrix M contains blocks with the transition matrix P, the classification matrix C, the identity matrix I and the zero matrix 0. The matrix was marked using with discrete forms of the selection and breakage functions, mean while the matrices of classification - using the equation, describing classification of grains in the grinding chamber of mill. In paper was discussed this model in details (part 2.1). The correctness of received form of the selection and breakage functions was confirmed. The method determination of the transition matrix for fluidized-jet grinding of grains (part 2.2) and the classification matrix for gravitational and centrifugal zones of grains (part 2.3) are presented. The verification of model obtained on basis results with experimental investigations, which were performed on a laboratory fluidized bed opposed jet mill. The experiment contained grinding of selected narrow size fractions of limestone in turbulent fluidized layer conditions, what in part I and part II of article (Zbroński, Górecka-Zbrońska 2007a, b) are presented. The parameters of parametric identification were: factor of proportionality - contained in the equation on the discrete form of selection function and sizes of limiting grains - contained in equation on the diagonal elements of classification matrix for stage of gravitational and centrifugal (part 3). The classic Fisher-Snedecor test was applied for estimation of prediction particle size distribution of grinding product (part 4). The significant divergences between numerical and experimental results of particle size distribution weren't affirmed. The experimental verification, parametric identification and statistical estimation of the proposed model showed that this model make it possible to forecasting particle size distribution of grinding product.
The purpose of the work was to experimentally determine the characteristics of the prototype of a Roto-Jet pump (the Pitot tube pump) during its operation under conditions typical for the domestic micro power plant. The low-boiling fluid, sold under the trade name of HFE7100 and characterised by a zero ozone depletion potential (ODP) coefficient, was used as a working medium in the organic Rankine cycle (ORC). An electric thermal oil heater with a maximum power of 2×24 kWe was used as a heat source. The pump of Roto-Jet type was specially designed for the operation with the following rated parameters of the thermodynamic cycle: nominal flow rate of the working fluid 0.17 kg/s, operating pressure 1.2 MPa. The pump was put under load using an expansion valve that simulated the operation of an expansion machine. The article discusses thermodynamic and flow conditions to be met by the pumping engine as well as results of the experimental research. Moreover, the article includes the operational characteristics of the ORC installation and the Roto-Jet pump obtained during the operation with the target working medium – HFE7100. The engineering problems the authors of this article faced when designing and testing the pumping engine prototype are also presented.
High-pressure jet grouting pile is a kind of stratum reinforcement technology developed in recent years. Due to its characteristics of high solid strength, fast construction, low noise, safety and reliability, low cost, controllable reinforcement diameter, strong adaptability to stratum, and good reinforcement effect for soft soil, loose soil and water-rich stratum, high-pressure jet grouting pile technology has been more and more widely used in foundation treatment, water stop, and seepage prevention, tunnel lining and other fields in recent years. As a country with a relatively late development of underground construction engineering, Vietnam has little research on special geotechnical reinforcement technology, especially on special geotechnical reinforcement technology around urban underground construction engineering, especially on its theoretical analysis and practical application. Therefore, this thesis combines the Vietnam Trung Hoa tunnel project as an example, using the theoretical calculation formula and field monitoring measurement comparing the two methods, the high pressure jet grouting pile system research in Vietnam in the underground engineering reinforcement principle and application effect, get to the actual engineering design and construction has a guiding significance to the research, provides the reference for future similar projects. Finally, the application effect of high-pressure jet grouting pile in underground building reinforcement project is evaluated, which proves that high-pressure jet grouting pile has good applicability and economic benefit in underground building reinforcement project in Vietnam.
This article proposes to use abrasive waterjet cutting (AWJ) for deflashing, deburring and similar finishing operations in casting. The basic requirements concerning the dimensional accuracy and surface texture of cast components are not met if visible surface flaws are detected. The experiments focused on the removal of external flash from elements made of EN-GJL-150 cast iron. The method employed for finishing was abrasive waterjet cutting. The tests were carried out using an APW 2010BB waterjet cutting machine. The form profiles before and after flash removal were determined with a Taylor Hobson PGI 1200 contact profiler. A Nikon AZ100 optical microscope was applied to observe and measure the changes in the flash height and width. The casting surface after finishing was smooth, without characteristic sharp, rough edges that occur in the cutting of objects with a considerable thickness. It should be emphasized that this method does not replace precise cutting operations. Yet, it can be successfully used to finish castings for which lower surface quality is required. An undoubted advantage of waterjet cutting is no effect of high temperature as is the case with plasma, laser or conventional cutting. This process is also easy to automate; one tool is needed to perform different finishing operations in order to obtain the desired dimensions, both internal and external.