Reconciliation between two copper ore mines transferred ore from one mine to another for processing in enrichment plants generated the need to regularly study the amount and composition of the ore on the conveyor connecting these two mines. To ensure the objectivity of the study, taking composite samples and their analysis was entrusted to a specialized outside laboratory. However, the managing staff of both mines still have doubts whether sampling results reflect correctly content of transported ore especially when the fed is highly variable. In order to investigate how the relatively low sampling rate affects the accuracy and precision of the measurement, the article investigates the hypothetical situation on the linking conveyor with the ore having extremely differentiated mineralization: 80% of almost barren rock (below 0.7% Cu) and 20% of the richly mineralized shale (around 10% Cu). Such ore occurs in some areas of the mine, from which it is fed onto a connecting conveyor. Through simulation techniques it was examined how the frequency of sampling can influence the distribution of the pooled sample results. It turned out that for 16 randomly selected samples in the following 15 minutes time intervals of a working shift, the spread of results around the simulated value is very large. A satisfactory accuracy level for the estimations of mean Cu content in the transported ore is achieved when the samples are collected at 30-second intervals. Only with sampling frequency close to on-line scanner parameters the probability of obtaining estimations with deviation exceeding 10% drops to the level of 2%. In the case of extremely differentiated ore doubts about confidence in the described measurements are fully confirmed, because with over 50% probability a single measurement could be deviated by 50% up and down from the true value.

One of the most critical aspects of mine design is to determine the optimum cut-off grade. Despite Lane’s theory, which aims to optimize the cut-off grade by maximizing the net present value (NPV), which is now an accepted principle used in open pit planning studies, it is less developed and applied in optimizing the cut-off grade for underground polymetallic mines than open pit mines, as optimization in underground polymetallic mines is more difficult. Since there is a similar potential for optimization between open pit mines and underground mines, this paper extends the utilization of Lane’s theory and proposes an optimization model of the cut-off grade applied to combined mining-mineral processing in underground mines with multi-metals. With the help of 3D visualization model of deposits and using the equivalent factors, the objective function is expressed as one variable function of the cut-off grade. Then, the curves of increment in present value versus the cut-off grade concerning different constraints of production capacities are constructed respectively, and the reasonable cut-off grade corresponding to each constraint is calculated by using the golden section search method. The defined criterion for the global optimization of the cut-off grade is determined by maximizing the overall marginal economics. An underground polymetallic copper deposit in Tibet is taken as an example to validate the proposed model in the case study. The results show that the overall optimum equivalent cut-off grade, 0.28%, improves NPV by RMB 170.2 million in comparison with the cut-off grade policy currently used. Thus, the application of the optimization model is conducive to achieving more satisfactory economic benefits under the premise of the rational utilization of mineral resources.

In order to enhance bioactive properties of titanium 99.2 used in implantology and various biomedical applications, numerous methods to form tight oxide coatings are being investigated. Some of these interesting techniques for generating TiO2 coatings include: electrochemical methods with anodizing, electric discharge treatment, plasma methods (PVD) and diffusive methods (i.e. oxidation in a fluidized bed). Each method aims to create a thin homogenous oxide coating characterized with thermal stability and repassivation ability in the presence of body fluid environment. However, new methods are still sought for increasing the biocompatibility of the substrate following a change in the intensity of depositing on the oxide coating compounds with high biocompatibility with body tissues, including hydroxyapatite, which constitutes the basis for subsequent osseointegration processes. The article presents investigation of HAp formation on titanium substrate surface after hybrid oxidation process. Hybrid surface treatments combine methods of fluidized bed atmospheric diffusive treatment FADT with the PVD surface treatment realized with different parameters (FADT – 640°C / 8h and PVD – magnetron sputtering with TiO2 target). In order to investigate the effects of hybrid oxidation and the formation of HAp molecules, SEM-EDS, SEM-EBSD, STEM-EDS, RS, nanoindentation and Kokubo bioactivity tests (c-SBF2) were carried out. The hybrid method of titanium oxidation, proposed by the Author, presents a new outlook on the modification and development of the properties of oxide coatings in the area of biomedical applications. Combining the ways of Ti Grade 2 oxidation in the hybrid method highly improves the formation of hydroxyapatite compounds and shows the potential of applying such a technique in implantology, where the intensive growth of bone tissues is crucial.

Over the past few years, a great deal of research has been conducted concerning the mathematical skills of children after the first stage of education. In my report, I present a selection of results from this research in order to illustrate the most typical didactical effects of the style in which mathematical education is performed in our schools. Comparing some detailed results from research in a number of chosen fields, I also try to assess whether or not, and how, the level of schoolchildren’s skills has changed in the recent years.

Safety and reliability are primary concerns in launch vehicle performance due to the involved costs and risk. Pressure vessels are one of the significant subsystems of launch vehicles. In order to have minimal weight, high strength material viz. maraging steel M250 grade is used in realizing the pressure vessel casing hardware. Despite the best efforts in design methodology, quality evaluation in production and effective structural integrity assessment is still a farfetched goal. The evolution of such a system requires, first, identification of an appropriate technique and next its adoption to meet the challenges posed by advanced materials like maraging steels. In fact, a quick survey of the available Non-Destructive Evaluation (NDE) techniques suggests Acoustic Emission (AE) as an effective structural integrity assessment tool capable of identifying any impending failure or degradation at an earlier stage. Experience shows that the longitudinal welds in the pressure vessels are quite vulnerable to failure due to the fact that they experience the maximum stress (i.e. hoop stress). Loading welded tensile samples are quite synonymous to the hoop stress experienced by longitudinal welds. An attempt is made to compare the Acoustic Emission data acquired during tensile deformation of maraging steel welded specimens. A total of 16 welded specimen’s with known defects were studied for their tensile behaviour is in connection with Acoustic Emission data. The lowest failure load was 70.5 kN and the highest being 84.8 kN. AE activity graphs viz. cumulative AE activity, hit rate, energy rate, count rate, AE amplitude history, AE count history, AE energy history, amplitude-count correlation and hit amplitude distribution have been investigated and salient features with respect to the data have been critically studied and relevant correlations are arrived at.

In order to recover the low grade waste heat and increase system fuel economy for main engine 10S90ME-C9.2-TII(part load, exhaust gas bypass) installed on a 10000 TEU container ship, a non-cogeneration and single-pressure type of waste heat recovery system based on organic Rankine cycle is proposed. Organic compound candidates appropriate to the system are analyzed and selected. Thermodynamic model of the whole system and thermoeconomic optimization are performed. The saturated organic compound vapor mass flow rate, net electric power output, pinch point, thermal efficiency and exergy efficiency varied with different evaporating temperature are thermodynamically analyzed. The results of thermodynamic and thermoeconomic optimization indicate that the most appropriate organic compound candidate is R141b due to its highest exergy efficiency, biggest unit cost benefit and shortest payback time.

Non-metallic inclusions found in steel can affect its performance characteristics. Their impact depends not only on their quality, but also,

among others, on their size and distribution in the steel volume. The literature mainly describes the results of tests on hard steels,

particularly bearing steels. The amount of non-metallic inclusions found in steel with a medium carbon content melted under industrial

conditions is rarely presented in the literature. The tested steel was melted in an electric arc furnace and then desulfurized and argonrefined.

Seven typical industrial melts were analyzed, in which ca. 75% secondary raw materials were used. The amount of non-metallic

inclusions was determined by optical and extraction methods. The test results are presented using stereometric indices. Inclusions are

characterized by measuring ranges. The chemical composition of steel and contents of inclusions in every melts are presented. The results

are shown in graphical form. The presented analysis of the tests results on the amount and size of non-metallic inclusions can be used to

assess them operational strength and durability of steel melted and refined in the desulfurization and argon refining processes.

In the work results of research on electrodischarge machining (EDM) of titanium alloy Ti10V2Fe3Al with (α + β) structure were presented. Preliminary heat treatment of samples allows to obtain different morphology and volume fraction of the α phase. The main goal of research was to assessment of the material microstructure impact on EDM technological factors (ie. material removal rate, tool wear) and morphology of technological surface layer. Electrodischarge machining is alternative and increasingly used method of titanium alloys machining. Research allowed to indicate the possibilities and limitations of use EDM in this area. It is especially important in the aspect of parts produced for aircraft industry and related requirements for the technological surface layer quality.

B a c k g r o u n d: A novel paradigm of diastolic heart failure with preserved ejection fraction (HFpEF) proposed the induction of coronary microvascular dysfunction by HFpEF comorbidities via a systemic pro-infl ammatory state and associated oxidative stress. Th e consequent nitric oxide deficiency would increase diastolic tension and favor fi brosis of adjacent myocardium, which implies not only left ventricular (LV), but all-chamber myocardial stiff ening. Our aim was to assess relations between low-grade chronic systemic infl ammation and left atrial (LA) pressure-volume relations in real-world HFpEF patients.

Me t h o d s: We retrospectively analyzed medical records of 60 clinically stable HpEFF patients in sinus rhythm with assayed high-sensitive C-reactive protein (CRP) during the index hospitalization. Subjects with CRP >10 mg/L or coexistent diseases, including coronary artery disease, were excluded. LV and LA diameters and mitral E/E’ ratio (an index of LA pressure) were extracted from routine echocardiographic 46 Cyrus M. Sani, Elahn P.L. Pogue, et al. records. A surrogate measure of LA stiff ness was computed as the averaged mitral E/e’ ratio divided by LA diameter.

R e s u l t s: With ascending CRP tertiles, we observed trends for elevated mitral E/e’ ratio (p <0.001), increased relative LV wall thickness (p = 0.01) and higher NYHA functional class (p = 0.02). Th e LA stiffness estimate and log-transformed CRP levels (log-CRP) were interrelated (r = 0.38, p = 0.003). On multivariate analysis, the LA stiff ness index was independently associated with log-CRP (β ± SEM: 0.21 ± 0.07, p = 0.007) and age (β ± SEM: 0.16 ± 0.07, p = 0.03), which was maintained upon adjustment for LV mass index and relative LV wall thickness.

C o n c l u s i o n s: Low-grade chronic infl ammation may contribute to LA stiff ening additively to age and regardless of the magnitude of associated LV hypertrophy and concentricity. LA stiff ening can exacerbate symptoms of congestion in HFpEF jointly with LV remodeling.

In this text, a critical reflection is presented on assessment practices in early childhood education, which are discussed in the context of the creation by those practices of the students’ sense of agency which, according to J. Bruner, is treated as a category of school culture. The discussion is based on the results of the recent research conducted in Poland on students’ agency and an analysis of the data collected as part of the author’s own research.

The picture obtained by using the triangulation of methods and sources confirms that assessment in early childhood education strips children of the opportunity to build a sense of agency, even in terms of independent control of a task situation. The surveyed students, admittedly, are capable of a relatively independent reflection on the context of school assessment, but the world of their educational experience is limited to the incapacitating culture of the school grade. It is a culture that becomes one of the sources of children’s self-restraint in the perception of themselves as agents, perpetuating their external steerability and passivity. To change this situation, external regulations will not suffice, but only the organizing of the learning environment based on the relationship between the teacher and the student, which is free from the daily pressures of assessment and the worship of formal correctness.

In this study, the compressive deformation of crushed sandstone was tested using a crushed rock deformation-seepage test system, and the effects of various factors, including crushed rock grade, grade combination, water saturation status, and stress loading method (i.e., continuous loading or cyclic loading and unloading), on the compressive deformation of crushed sandstone was analyzed from four perspectives including stress-strain, bulking coefficient, deformation mechanism and energy dissipation. The results indicate that the stress-strain relations of crushed sandstone are closely associated with all factors considered, and are well represented by exponential functions. The strain observed for a given applied stress increased with increasing crushed rock grade throughout the loading period. Crushed sandstone grades were combined according to a grading index (n), where the proportion of large-grade rocks in the sample increased with increasing n. The bearing capacity of a water-saturated crushed sandstone sample with n = 0.2 was less than that of an equivalent dry sample for a given applied stress. The stress-strain curve of a water-saturated crushed sandstone sample with n = 0.2 under cyclic loading and unloading was similar to that obtained under continuous loading. Observation and discovery, the deformation mechanism of crushed sandstone was mainly divided into four stages, including crushing, rupture, corner detachment and corner wear. And 20% of the work done by testing machine is used for friction between the crushed sandstone with the inner wall of the test chamber, and 80% is used for the closing of the void between the crushed sandstone, friction sliding, crushing damage.

Chromium ore is treated as an important strategic raw material. It is used by many branches of the industry. The most important applications are metallurgical, refractory and chemical. Unfortunately, no chromium ore deposits have been found in Poland until now, with the exception of two chromium ore sites described in the Lower Silesia region. These concentrations are formed by chromitite, which is rock consisting mainly of chromian spinel. They are localized within so called Sudetic Ophiolite rocks along the edge of the Góry Sowie Massif. They form typical podiform deposits, which are characterized by the high Al content of the rock. The first locality, near Tąpadła village (the Gogołów-Jordanów Massif), is better known. The ore was exploited here at the turn of the19th century and at the beginning of the 20th century. According to the literature, 3500 tons of the ore was obtained - all the resources at this location. The second locality, situated at the Braszowice-Brzeźnica Massif, was never studied and described properly, falling into obscurity since the 19th century. During the field work at the Braszowice-Brzeźnica Massif, the author has found numerous chromium ore fragments among the debris. The rising prices of chromium on the world's markets suggest that it is reasonable to study the ore quality and overall resource potential of this deposit. The preliminary studies have shown that chromitities from Braszowice are typical ores of the podiform variety, the majority texturally massive and nodular. The chemical analyses of the primary chromianspinels grains revealed that they could be treated as refractory chromite (38% wt. of Cr2O3, lower than 30% wt. of Al2O3, and Cr/Fe ratio about 3:1). However, the metamorphic processes modified the primary chemical composition of the studied ore. They caused enrichment in Fe and Cr, and a decrease in Al in comparison to the primary ore. Moreover, the whole rock chemical analyses revealed that the content of the main elements is insufficient to use the ore without enrichment processes. Furthermore, the size and number of the potential ore bodies are presumably small. Consequently, both the chemical composition and the resources of the chromium ores from the Braszowice–Brzeźnica Massif are insufficient to allow for profitable exploitation, despite the high price of chromium.

Ballast layer has weighty share in the lifecycle costs of railway track. The strict standards and maintenance rules of ballast grading significantly contribute to the ballast costs. One ways to the costs reduction is differential demands to ballast grading for the secondary and low loaded railway lines. Additional one is the different ballast grading over the ballast height. This study presents a full scale laboratory investigation of technical efficiency of such railway ballast under the long-term cyclic loading in comparison with the standard ballast layer. The double layer is presented with standard grading ballast upper layer and bottom sub ballast layer consists of ballast mixture. Pressure distribution under the ballast layer and permanent settlements of the layers are measured during the loading cycles. The reference measurements with standard grading ballast material are carried out. The study shows that initial settlement accumulation of the double layer railway ballast are lower to that of the standard ballast layer. However, the settlements accumulation intensity of the ballast is higher. The analysis of the pressure distribution measurements under the ballast layer and the settlements inside the ballast layer explain the causes of the different settlement accumulation.