Fast and accurate grid signal frequency estimation is a very important issue in the control of renewable energy systems. Important factors that influence the estimation accuracy include the A/D converter parameters in the inverter control system. This paper presents the influence of the number of A/D converter bits b, the phase shift of the grid signal relative to the time window, the width of the time window relative to the grid signal period (expressed as a cycle in range (CiR) parameter) and the number of N samples obtained in this window with the A/D converter on the developed estimation method results. An increase in the number b by 8 decreases the estimation error by approximately 256 times. The largest estimation error occurs when the signal module maximum is in the time window center (for small values of CiR) or when the signal value is zero in the time window center (for large values of CiR). In practical applications, the dominant component of the frequency estimation error is the error caused by the quantization noise, and its range is from approximately 8×10-10 to 6×10-4.

An integrated Z-source inverter for the single-phase single-stage grid-connected photovoltaic system is proposed in this paper. The inverter integrates three functional blocks including maximum-power-point-tracking, step-up/down DC-side voltage and output grid-connected current. According to the non-minimum-phase characteristic presented in DC-side and the functional demands of the system, two constant-frequency sliding-mode controllers with integral compensation are proposed to guarantee the system robustness. By using two controllers, the effects caused by the non-minimum-phase characteristic are mitigated. Under the circumstance of that the input voltage or the grid-connected current changes suddenly, the notches/protrusions following the over-shoot/ under-shoot of the DC-bus voltage are eliminated. The quality of grid-connected current is ensured. Also, a small-signal modelling method is employed to analyze the close-loop system. A 300W prototype is built in the laboratory. A solar-array simulator (SAS) is used to verify the systematic responses in the experiment. The correctness and validity of the inverter and proposed control algorithm are proved by simulation and experimental results.

This article considers designing of a renewable electrical power generation system for self-contained homes away from conventional grids. A model based on a technique for the analysis and evaluation of two solar and wind energy sources, electrochemical storage and charging of a housing area is introduced into a simulation and calculation program that aims to decide, based on the optimized results, on electrical energy production system coupled or separated from the two sources mentioned above that must be able to ensure a continuous energy balance at any time of the day. Such system is the most cost-effective among the systems found. The wind system adopted in the study is of the low starting speed that meets the criteria of low winds in the selected region under study unlike the adequate solar resource, which will lead to an examination of its feasibility and profitability to compensate for the inactivity of photovoltaic panels in periods of no sunlight. That is a system with fewer photovoltaic panels and storage batteries whereby these should return a full day of autonomy. Two configurations are selected and discussed. The first is composed of photovoltaic panels and storage batteries and the other includes the addition of a wind system in combination with the photovoltaic system with storage but at a higher investment cost than the first. Consequently, this result proves that is preferable to opt for a purely photovoltaic system supported by the storage in this type of site and invalidates the interest of adding micro wind turbines adapted to sites with low wind resources.

In this work, two thermal- and air-stable, hole transporting materials (HTM) in perovskite solar cells are analyzed. Those obtained and investigated materials were two polyazomethines: the first one with three thiophene rings and 3,3′-dimethoxybenzidine moieties (S9) and the second one with three thiophene rings and fluorene moieties (S7). Furthermore, presented polyazomethines were characterized by Fourier transform infrared spectroscopy (FTIR), UV–vis spectroscopy, atomic force microscopy (AFM) and thermogravimetric analysis (TGA) experiments. Both polyazomethines (S7 and S9) possessed good thermal stability with a 5% weight loss at 406 and 377°C, respectively. The conductivity of S7 was two orders of magnitude higher than for S9 polymer (2.7 × 10⁻⁸ S/cm, and 2.6 × 10⁻¹⁰ S/cm, respectively). Moreover, polyazomethine S9 exhibited 31 nm bathochromic shift of the absorption band maximum compared to S7.

Obtained perovskite was investigated by UV–vis and XRD. Electrical parameters of perovskite solar cells (PSC) were investigated at Standard Test Conditions (STC). It was found that both polyazomethines protect perovskite which is confirmed by ageing test where Voc did not decrease significantly for solar cells with HTM in contrast to solar cell without hole conductor, where V_oc decrease was substantial. The best photoconversion efficiency (PCE = 6.9%), among two investigated in this work polyazomethines, was obtained for device with the following architectures FTO/TiO₂/TiO₂ + perovskite/S7/Au. Stability test proved the procreative effects of polyazomethines on perovskite absorber.

The energy efficiency of photovoltaic modules is one of the most important aspects in energetic and economic aspects of the project related to system installations. The efficiency of modules and the electricity produced by photovoltaic conversion in solar modules is affected by many factors, both internal, related to the module structure itself and its technical and external factors related to the energy infrastructure, which includes: cabling, inverters, climate conditions prevailing at the micro-installation location and the orientation and angle of inclination of the solar modules. The installation of photovoltaic modules should be preceded by an energy efficiency analysis, which will help to indicate the optimal solution adapted to the given conditions. The article presents a comparative analysis of the amount of energy produced under real and simulated conditions. Analyzes were made on the basis of research carried out in the Wind and Solar Energy Laboratory located at the AGH University of Science and Technology, data from solar irradiation data-bases and computer software for estimating energy resources. The study examined the correlation of the solar irradiation on the modules and the amount of electricity generated in the photovoltaic module. The electricity produced by the module was compared under real conditions and simulated based on two sources of data. The comparison and analysis of the amount of energy of the module were also made, taking simulated different angles of the module’s inclination into account.

The paper presents the results of the energy analysis of the conversion of solar radiation energy into electrical energy in Polish weather conditions. The effect of sunlight and working temperature on the photovoltaic module on its power curve P = f(U) is shown. STC and NOCT conditions are described for which the manufacturers specify the parameters of the photovoltaic modules. The manufacturers of photovoltaic panels should give the PPV = f(E) characteristic for the different values of the operating temperature of the modules. An analysis of the economic efficiency of a photovoltaic power plant investment of 1 MWp taking the current legal regulations for the three variants into account was presented. Variant I – the investor benefits from the support of public aid of operational only, Variant II – the investor benefits from the support of public aid for investment in the amount of PLN 1 million, Variant III – the investor benefits from the support of public aid for investment in the amount of PLN 2 million. For all variants, indicators for assessing the economic effectiveness of the investment and the value of the auction price from the maximum price to the price at which the project loses its profitability are determined.

Photovoltaic (PV) technologies which play a role in PV market are divided into basic two types: wafer-based (1st generation PV) and thin-film cell (2nd generation PV). To the first category belong mainly crystalline silicon (c-Si) cells (both mono- and multi-crystalline). In 2015 around 90% of the solar market belonged to crystalline silicon. To the 2nd generation solar cells belongs thin film amorphous silicon (a-Si) or a combination of amorphous and microcrystalline silicon (a-Si/μc-Si), compound semiconductor cadmium telluride (CdTe), compound semiconductor made of copper, indium, gallium and selenium (CIS or CIGS) and III–V materials. The PV market for thin film technology is dominated by CdTe and CIGS solar cells. Thin film solar cells’ share for all thin film technologies was only 10% in 2015. New emerging technologies, called 3rd generation solar cells, remain the subject of extensive R&D studies but have not been used in the PV market, so far.

In this review the best laboratory 1st and 2nd generation solar cells that were recently achieved are described. The scheme of the layer structure and energy band diagrams will be analyzed in order to explain the boost of their efficiency with reference to the earlier standard designs.

The large variability and unpredictability of energy production from photovoltaic power microinstallations results from the dependence on the current weather conditions. These conditions depend on a number of factors and are variable over the time. Despite this specificity, photovoltaic micro-installations are becoming more and more popular in the world and in Poland. This is mainly due to the fact that the generation of energy from renewable sources has numerous advantages, the energy is free, renewable in time and ecological, and its production on its own gives partial independence from energy supplies from the power grid. In addition, the observed significant prices decrease of solar modules has further accelerated the development of the use of this energy source. Concern for this method of energy production among households has increased significantly in Poland after introducing the prosumer in the legal framework and the use of administrative and financial support. The implemented prosumer mechanisms allowed, for example, the net balancing of the energy consumed and produced by the micro-installation through storage in the power grid. The article describes the problem of balancing sources using solar energy, based on micro-installation used in the household (the so-called prosumer installation). The conducted analyses compared the load profile of a typical household and the energy generation profile from a photovoltaic installation, determining the real balancing formation level of such a system.

Recently, the search for new effective energy production solutions has been focused on the production of electricity using renewable and environmentally friendly carriers. This resulted in an increased interest in PV cells and cogeneration systems. The article looks at the main factors affecting their operational parameters against the background of the development history of subsequent generations of PV cells. Average daily solar radiation and wind velocity in Lodz were characterized. The research was done on a static and tracking system with a total peak power of 15 kWp and a 30 kW microturbine. PV panels are installed on the building of the Institute of Electrical Power Engineering of the Lodz University of Technology and they work as part of DERLab. A microturbine is inside the building. Energy measurements were carried out in 2016 giving grounds for the analysis of energy efficiency and financial analysis of the energy supply in buildings. Energy yields in the static and tracking system as well as percentage coverage of electricity from PV cells and microturbines were assessed. The distribution of monthly savings, annual savings of energy costs and the payback time of the investment costs of the systems subject to the test were determined. The research we have done allows us to say that the energy produced by follow-up modules is about 3 times greater than that generated in stationary modules. On the other hand, the annual savings of energy costs using gas micro-turbines are about 10 times higher than those of lagging panels. The analysis shows that it is possible to determine the profitability of the microturbine and photovoltaic panels use despite large financial outlays. The payback period of investment outlays is about 12 years when using the installation throughout the year.

The overriding objective of the National Electric Power System (KSE) is to ensure the security of electricity supply. In summer, the upward trend in the demand for electric energy is caused by, among others, the proliferation of air conditioners. Therefore, the upward trend in summer’s on-peak demand is expected to be maintained. Examples from 2015, 2016 or 2018 indicate that National Electric Power System needs a summer’s on-peak source that will be able to produce electricity regardless of the hydrological conditions. Photovoltaics is a source of energy that can cover the peak demand during sweltering heat. This article briefly characterizes the problem of increasing demand for electricity in summer and uses examples that have taken place in recent years. The main conclusion is the postulate for the extension of photovoltaic power in the National Electric Power System, the purpose of which will be the production of electricity during sweltering heat, covering the peak load in the system. This article presented both the advantages and disadvantages of such a solution. Unfavorable weather conditions (high air temperature, low water level, lack of wind) limit the production of electricity from wind farms or conventional power plants, and also increase transmission losses, which is why photovoltaics is a desirable source from the National Electric Power System’s point of view. The article refers to examples from the Czech Republic and Germany, where a significant installed capacity of photovoltaics enables the stable operation of the power system during sweltering heat. It was also pointed out that the role of photovoltaics in the National Electric Power System is growing, which is consistent with the assumptions of the Polish Energy Policy Project until 2040.