In this paper, an analysis of various factors affecting machined surface texture is presented. The investigation was focused on ball end mill inclination against the work piece (defined by surface inclination angle a. Surface roughness was investigated in a 3D array, and measurements were conducted parallel to the feed motion direction. The analysis of machined surface irregularities as a function of frequency (wavelength A), on the basis of the Power Density Spectrum - PDS was also carried out. This kind of analysis is aimed at valuation of primary factors influencing surface roughness generation as well as its randomness. Subsequently, a surface roughness model including cutter displacements was developed. It was found that plain cutting with ball end mill (surface inclination angle a= 0°) is unfavorable from the point of view of surface roughness, because in cutter’s axis the cutting speed vc ~ 0 m/min. This means that a cutting process does not occur, whereas on the machined surface some characteristics marks can be found. These marks do not appear in case of a* 0°, because the cutting speed vc * 0 on the fill I length of the active cutting edge and as a result, the machined surface texture is more homogenous. Surface roughness parameters determined on the basis of the model including cutter displacements are closer to experimental data for cases with inclination angles a* 0°, in comparison with those determined for plain cutting (a= 0°). It is probably caused by higher contribution in surface irregularities generation of plastic and elastic deformations cumulated near the cutter’s free end than kinematic and geometric parameters, as well as cutter displacements.
The paper presents theoretical analysis and simulation results of the process of regular surface texture generation by grinding with the wheel shaped in a special way. Simple variant of the method consists in grinding with the wheel having single helical groove. Non-uniform load of abrasive grains located in different zones of the wheel circumference was described. Two models (deterministic and probabilistic) of the wheel active surface were developed, assuming different grain arrangement. Results of two models were compared and differences were explained.
The results of surface texture measurements obtained with the stylus equipment, white light interferometer
and confocal profilometer of the same samples were compared. Machined isotropic and anisotropic surfaces,
of symmetric and asymmetric ordinate distribution were measured. Forms were removed using polynomials.
Sampling intervals and measuring areas during computations of parameters were the same. Discrepancies
between the results obtained with various methods were observed and discussed. It was found that errors of
surface texture measurement with the optical methods depend on the type of surface topography.
The objective of the study was to assess the potential use of optical measuring instruments to determine the minimum chip thickness in face milling. Images of scanned surfaces were analyzed using mother wavelets. Filtration of optical signals helped identify the characteristic zones observed on the workpiece surface at the beginning of the cutting process. The measurement data were analyzed statistically. The results were then used to estimate how accurate each measuring system was to determine the minimum uncut chip thickness. Also, experimental verification was carried out for each mother wavelet to assess their suitability for analyzing surface images.
We present a prototype of a simple, low-cost setup for a fast scatterometric surface texture measurements. We used a total integrated scatter method (TIS) with a semiconductor laser (λ = 638 nm) and a Si photodiode. Using our setup, we estimated the roughness parameters Rq for two reference surfaces (Al mirrors with flatness λ/10) and seven equal steel plates to compare. The setup is easily adaptable for a fast, preliminary manufacturing quality control. We show is possible to construct a low-cost measurement system with nanometric precision.
Signal analysis performed during surface texture measurement frequently involves applying the Fourier transform. The method is particularly useful for assessing roundness and cylindrical profiles. Since the wavelet transform is becoming a common tool for signal analysis in many metrological applications, it is vital to evaluate its suitability for surface texture profiles. The research presented in this paper focused on signal decomposition and reconstruction during roundness profile measurement and the effect of these processes on the changes in selected roundness profile parameters. The calculations were carried out on a sample of 100 roundness profiles for 12 different forms of mother wavelets using MATLAB. The use of Spearman's rank correlation coefficients allowed us to evaluate the relationship between the two chosen criteria for selecting the optimal mother wavelet.
This work is focused on the issue of non-measured points – one of the most important problems in surface texture measurements using optical methods. The fundamental aim of this research is to analyse errors of surface texture measurements caused by the presence of non-measured points. This study is divided into two parts. In the first part, circles with non-measured points were artificially created on peak portions of measured surfaces. In the second part – the results of measurement by a Talysurf CCI Lite interferometer were analysed. A measurement area of 3.3 × 3.3 mm contained 1024 × 1024 points. The measurements were performed with different intensity of light. Changes of parameters regarding the analysed errors depended on a surface type. The following parameters are susceptible to errors: skewness Ssk, areal material ratio Smr, as well as the following feature parameters: Spd, Sda, Sdv, Sha and Shv. Inaccuracies of measurement in valley parts of two-process textures led usually to larger errors of parameter computations compared with deviations in peak portions.
Hard turning is a machining process that is widely used in the precision mechanical industry. The characterization of the functional surface texture by the ISO 13565 standard holds a key role in automotive mechanics. Until now, the impact of cutting conditions during hard turning operation on the bearing area curve parameters has not been studied (ISO 13565). The three parameters Rpk , Rk and Rvk illustrate the ability of the surface texture to resist friction. In this work, the main objective is to study the impact of cutting conditions (Vc, f and ap) of the hard turning on three parameters of the bearing area curve. The statistical study based on response surface methodology (RSM), analysis of variance (ANOVA) and quadratic regression were performed to model the three output parameters and optimize the input parameters. The experimental design used in this study is the Taguchi L25 orthogonal array. The results obtained show that the cutting speed has a greater effect on the bearing ratio curve (Rpk , Rk and Rvk ) parameters with a percentage contribution of 37.68%, 37.65% and 36.91%, respectively. The second significant parameter is the feed rate and the other parameter is significant only in relation to Rpk and Rk parameters.
In this paper both envelope approach and morphological filters for characterisation of surface textures were proposed, applied and thoroughly examined. Obtained results were compared with those received after appliance of commonly-used algorithms. The effect of appliance of proposed procedures on surface topography parameters (from ISO 25178 standard) was taken into consideration. The following types of surface textureswere assessed: two-process plateau-honed cylinder liners, plateau-honed cylinder liners with additionally burnished dimples, turned piston skirts, grinded and/or isotropic topographies. It was assumed that envelope characteristics (envelope filtration) can provide results useful for assessments of deep and/or wide oil-reservoirs especially when they are edge located. Moreover, some near-valley areas of surface texture details can be less distorted when envelope filtering is accomplished. It was also found that closing and/or opening envelope filtration can be valuable for reduction of some surface topography measurement errors.