Archives of Metallurgy and Materials
Archives of Metallurgy and Materials is a quarterly of Polish Academy of Sciences and Institute of Metallurgy and Materials Science of the Polish Academy of Sciences, which publishes original scientific papers and reviews in the fields of metallurgy and materials science. Papers with focus on synthesis, processing and properties of metal materials, including thermodynamic and physical properties, phase relations, and their relation to microstructure of materials are of particular interest.
IMPACT FACTOR 2023: 0.7
CiteScore 2023 - 1,20
SNIP 2023 - 0,343
SJR 2023 - 0,208
Score of the Ministry of Science and Higher Education = 40
Submit your article
The grain boundary wetting phase transition in an industrial EZ33A cast
alloy is studied. 12% of the grain boundaries are completely wetted at
the temperature slightly higher than the eutectic transformation
temperature (530°C). The fraction of wetted grain boundaries increases
with temperature, reaches a maximum of 85% at 570°C, and does not change
further until the alloy melts. In the as-cast state, the alloy has low
ductile properties at the ambient temperature. The microstructure in the
as-cast state corresponds to the wetting state at about 560°C, which
indicates that the cooling rate in casting is almost equal to that in
quenching. The volume and the surface fraction of the second phase and
the hardness measured at the least wetted state of samples point to its
good machinability. The wetting data are used to suggest a sequence of
heat treatment and machining for processing EZ33A alloy parts.
Editorial address: Marta Bitner Strata Mechanics Research Institute, Polish Academy of Science, 27 Reymonta Str., 30-059 Kraków, Poland tel. +48 (012) 637 62 00 w. 58, e-mail: archiwum4@wp.pl, amm@imim.pl Technical Editors: Piotr Bala, AGH University of Science and Technology, Poland Paweł Czaja, Institute of Metallurgy and Materials Science PAS, Poland Przemysław Fima, Institute of Metallurgy and Materials Science PAS, Poland Marek Kopyto, Institute of Metallurgy and Materials Science PAS, Poland Wojciech Święszkowski, Warsaw University and Technology, Poland Maciej Szczerba, Institute of Metallurgy and Materials Science PAS, Poland
Assistant Editor:
EDITORIAL BOARD Editor-in-Chief: Maciej Szczerba, Institute of Metallurgy and Materials Science PAS, Poland Piotr Bała, AGH University of Science and Technology, Poland Przemysław Fima, Institute of Metallurgy and Materials Science PAS, Poland Krzysztof Fitzner, AGH University of Science and Technology, Poland Bogusław Major, Institute of Metallurgy and Materials Science PAS, Poland Romana Ewa Śliwa, Rzeszow Univesity of Technology, Poland Wojciech Święszkowski, Warsaw University of Technology, Poland Paweł Zięba, Institute of Metallurgy and Materials Science PAS, Poland EDITORIAL ADVISORY BOARD Mohd Mustafa Al Bakri Abdullah, University of Malaysia Leszek Blacha, Silesian University of Technology, Poland Zbigniew Bojar, Military University of Technology, Poland Eduardo Cesari, University of the Balearic Islands, Spain Kyu Rhee Chang, Korea Atomic Energy Research Institute, Korea Volodymyr Chernenko, Basque Center For Materials, Spain Jan Dusza, Institute of Materials Research, SAS, Slovakia Władysław Gąsior, Institute of Metallurgy and Materials Science PAS, Poland Volodymyr Golub, Institute of Magnetism NASU, Ukraine Zbigniew Gronostajski, Wroclaw University of Technology, Poland Edward Guzik, AGH University of Science and Technology, Poland George Kaptay, Research Institute on Nanotechnology, Hungary Alexandre Kodentsov, Eindhoven University of Technology, Netherlands Rafał Kozubski, Jagiellonian University, Poland Aleš Kroupa, Institute of Physics of Materials AS CR, Czech Republic Piotr Kula, Lodz University of Technology, Poland Jan Kusiński, AGH University of Science and Technology, Poland Roman Kuziak, Institute of Ferrous Metallurgy, Poland Jüergen Lackner, Laser Center Leoben, Joanneum Research, Austria Kee Ahn Lee, Inha University, Korea Marcin Leonowicz, Warsaw University of Technology, Poland Małgorzata Lewandowska, Warsaw University of Technology, Poland Jerzy Lis, AGH University of Science and Technology, Poland Viktor Lvov, Kyiv National University, Ukraine Leszek B. Magalas, AGH University of Science and Technology, Poland Graeme E. Murch, University of Newcastle, Australia Marcin Nabiałek, Czestochowa University of Technology, Poland Alberto Passerone, Institute of Physical Chemistry of Materials, Italy Eugen Rabkin, Technion Israel Institute of Technology, Israel Amir Shirzadi, University of Cambridge, United Kingdom Jerzy Sobczak, Foundry Research Institute, Poland Sudipta Seal, University of Central Florida, United States of America Pekka Taskinen, Aalto University, Finland Stefan Zaefferer, Max-Planck-Institut, Germany Ehrenfried Zschech, BTU Cottbus-Senftenberg, Germany BOARD OF REVIEW Janusz Adamiec, Marek Blicharski, Marcin Brzeziński, Ryszard Dąbrowski, Stanisław Dymek, Robert Filipek, Sebastian Garus, Franciszek Grosman, Halina Garbacz, Marcin Górny, Adam Grajcar, Marek Hetmańczyk, Jarosław Jakubski, Mieczysław Jurczyk, Agnieszka Kopia, Marian Kucharski, Beata Leszczyńska-Madej, Marcin Leonowicz, Łukasz Madej, Piotr Migas, Maciej Motyka, Jerzy Pacyna, Zbigniew Pędzich, Łukasz Rauch, Kinga Rodak, Maria Sozańska, Tomasz Tański, Krzysztof Wierzbanowski, Joanna Wojewoda-Budka, Waldemar Wołczyński, Piotr Żabiński
EDITORS
When preparing the manuscript, please pay attention to the following rules: 1. Manuscript submission 1.1. Manuscripts to be considered for publication should be submitted to the Editorial Office via www.editorialsystem.com/amm/. Authors should designate corresponding author, whose responsibility is to represent the Authors in contacts with the Editorial Office. The corresponding author receives an e-mail notification confirming the submission of the manuscript to the Editorial Office and is informed about the progress of the review process. 1.2. Manuscript should not exceed 15 pages of full-size paper (A4), must be double spaced (please use 12 point font), with generous margins, and the pages must be numbered. Authors should submit an electronic file of their manuscript in Microsoft Word (minimum : version 2000). 1.3. All manuscripts must be written in good English. Both British and U.S. English are acceptable but Authors should be consistent in their usage. It is sole responsibility of the Authors to make sure that the manuscript is grammatically correct and spell checked. Authors are strongly encouraged to have the manuscript proofread by a native speaker of English or a language professional, before it is submitted to the editorial office. Papers written in poor English will be automatically rejected without being subjected to review. 1.4. Authors should submit an electronic copy of final version of their paper in Microsoft Word Format, shemes (sketches) and figures saved as .eps, .jpeg, or .tiff. 1.5. Articles submitted for publication should include abstract and maximum 5 keywords. 1.6. Please adhere to the following order of presentation: Author(s) with first names in full and ORCID. Affiliation(s): in a short form (Institution, City, Country). Use the superscripts (*, **, . . .) after the Authors’ names in case of different affiliations. Title: All words in lower case (first letter of first word capitalized). Keywords: 5 maximum. Main text: Begin on the second page with Introduction, followed by Experimental (Materials and Methods) and/or Theory section, Results, Discussion, and end with Conclusion section and Acknowledgement. When appropriate the Authors may choose to combine Results section and Discussion section into one Results and Discussion section. Make sure the text in sections is divided logically into paragraphs. References Correspondence address: title, name, postal address, telephone and e-mail address of the corresponding Author, number ORCID. Figure captions Tables 2. Manuscript preparation 2.2. Figures Figures should be complete without corrections and additions in the word. Figures are usually printed in reduced size (fitting column width of 85 mm) and this should be taken into account when preparing them. For the best results, make sure that lettering on figures and micrographs is at least 2 mm high after reduction, and the style of labeling must be uniform for all figures. Each figure should have its own caption explaining the content without reference to the text. Figure captions should be typed on a separate page at the end of manuscript. The appropriate place of in the text should be indicated by <Fig. 3 > written in separate line. Figures should be referred to in text as follows: Fig. 1. The magnification must be indicated by a labeled scale marker on the micrograph itself, not drawn below it. For optimum printing quality micrographs should be saved as .eps or .tiff at a resolution of at least 300 dpi while line drawings at a resolution of at least 600 dpi. 2.3. Move file The files will be removed from the edytorial system when rejected or published article (moved to Rejected or Published manuscripts). Tables together with captions should be typed on separate page at the end of manuscript. Tables are to be numbered consecutively using Arabic numbers in the text (TABLE 1 . . . n). A caption must be placed above respective table and should explain the symbols used in the heading and in the left hand column. Tables should be referred to in the text as follows: TABLE 1. References should be typed on separate pages and numbered consecutively applying the system accepted by the Quarterly (initials and names all authors, journal title [abbreviated according to the Journal Title Abbreviations of Web of Science: http://library.caltech.edu/reference/abbreviations/, everyone abbreviation should be end with a dot - example. Arch.Metall.Mater.] or book title; journal volume or book publisher; page spread; publication year in bracket). The use of DOI numbers (full notation and linked) is mandatory for each paper and should be formatted as shown in the examples below: Journals: [1] L.B. Magalas, Development of High-Resolution Mechanical Spectroscopy, HRMS: Status and Perspectives. HRMS Coupled with a Laser Dilatometer. Arch. Metall. Mater. 60 (3), 2069-2076 (2015). DOI: https://doi.org/10.1515/AMM-2015-0350 [2] E. Pagounis, M.J. Szczerba, R. Chulist, M. Laufenberg, Large Magnetic Field-Induced Work output in a NiMgGa Seven-Lavered Modulated Martensite. Appl. Phys. Lett. 107, 152407 (2015). DOI: https://doi.org/10.1063/1.4933303 [3] H. Etschmaier, H. Torwesten, H. Eder, P. Hadley, Suppression of Interdiffusion in Copper/Tin thin Films. J. Mater. Eng. Perform. (2012).DOI: https://doi.org/10.1007/s11665-011-0090-2 (in press). Books: [2] M. H. Kamdar, A.M.C. Westwood, Environment-Sensitive Mechanical Behaviour, New York 1981. Proceedings: [3] F. Erdogan, in: H. Liebowitz (Ed.), Fracture 2, Academic Press 684, New York (1968). Internet resource: [4] http://www.twi.co.uk/content/fswqual.html PhD Thesis: [6] F.M. LIang. World Hyphenation by Computer. PhD thesis, Stanford University, Stanford, CA 94305, June. Chapter in books: [7] R. Major, P. Lacki, R. Kustosz, J. M. Lackner, Modelling of nanoindentation to simulate thin layer behavior, in: K. J. Kurzydłowski, B. Major, P. Zięba (Ed.), Foundation of Materials Design 2006, Research Signpost (2006). Articles in press: [8] H. EtschmaIer, H. Torwesten, H. Eder, P. Hadley, J. Mater. Eng. Perform. (2012), DOI: 10.1007/s11665-011-0090-2 (in press). 3. Fees No honorarium will be paid. The journal does not have article processing charges (APCs) nor article submission charges. 4. Review and proofread process 4.1. Peer review process All submitted manuscripts undergo review by renowned specialists appointed by the Editor-in-Chief and members of the Editorial Board. Reviewers receive guidance to help them perform the review, and submit written opinion on the manuscript together with recommendation to accept as is, or reject, or accept after revision. In the latter case i.e. when revision is requested, the authors are obliged to respond to Editor and Reviewers’ comments in detail and make revisions to the manuscript. A rebuttal to Reviewers’ comments can also be sent via the Editorial System in writing. Decision to reject the article is taken by the Editorial Board with the final decision belonging to the Editor, who may appoint another reviewer if necessary. Reviewers remain anonymous to Authors and their identity cannot be revealed by the Editorial Office. In a separate file, the authors are requested to suggest names and contact details (affiliations and valid e-mail addresses) of at least three experts who could serve as reviewers. Brief explanation (2-3 sentence-long) why each person is suitable as a reviewer should also be provided. The suggested reviewers cannot be from the same country as affiliation of the corresponding author. The decision to appoint a reviewer belongs solely to the editor. 4.2. Revised manuscript submission When revision of a manuscript is requested, Authors should return the revised version of their manuscript as soon as possible. Prompt action may ensure fast publication if a paper is finally accepted for publication in Arch. Metall. Mater. If it is the first revision of an article Authors are requested to return their revised manuscript within 7 days. If it is the second revision Authors are requested to return their revised manuscript within 1 day. 4.3. Final proofreading Authors will receive a pdf file with the edited version of their manuscript for final proofreading. This is the last opportunity to view an article before its publication on the journal web site. No changes or modifications can be introduced once it is published. Thus authors are requested to check their proof pages carefully against manuscript within 3 working days and prepare a separate document containing all changes that should be introduced. Authors are sometimes asked to provide additional comments and explanations in response to remarks and queries from the language or technical editors. 5. Original version Starting from issue 1/ 2018, Volume 63, Archives of Metallurgy and Materials is published in electronic via www.journals.pan.pl. The printed version is printed only for designated libraries (legal basis: Regulation of the Minister of Culture and Art of March 6, 1997). 6. Prevent cases of plagiarism Readers should be sure that the authors present the results of their work transparently, fair and honest, regardless of whether they are the direct authors, or used the help of a specialized entity (natural or legal person). To prevent cases of plagiarism, "ghostwriting" and "guest Authorship", the Editorial Office will require that the Authors disclosed the contribution of individual Authors in the creation of manuscript (with their affiliations and contributions, i.e. the information who is responsible for: research concept and design, collection and/or assembly of data, data analysis and interpretation, writing the manuscript). Funding sources (together with grant number) must also be revealed. The corresponding Author will bear the main responsibility for the manuscript. Detected cases will be exposed, including notifying the appropriate entities (institutions employing the Authors, scientific societies, associations of editors of scientific journals, etc.). 7. License type Articles are printed in an open access and distributed under the terms of the Creative Commons Attribution-NonCommercial (CC BY-NC 4.0, https://creativecommons.org/licenses/by-nc/4.0/). This license allows authors to copy and redistribute the material in any medium or format, remix, transform, and build upon the material. Authors may not use the material for commercial purposes. However, this condition does not include dependent works (they may be covered by another license). Submission of an article to the journal is unequivocal to expressing consent to the publication in both paper and electronic form.
Archives of Metallurgy and Materials is a quarterly journal of Polish Academy of Sciences and Institute of Metallurgy and Materials Science PAS which publishes original scientific papers and reviews in the fields of metallurgy and materials science, foundry, mechanical working of metals, thermal engineering in metallurgy, thermodynamic and physical properties of materials, phase equilibria in the broad context and diffusion. In addition to the regular, original scientific papers and conference proceedings, invited reviews presenting the up-to-date knowledge and monothematic issues devoted to preferred areas of research will be published. Submission of a paper implies that it has not been published previously, that it is not under consideration for publication elsewhere, and that if accepted it will not be published elsewhere in the same form.
Abstract: maximum 10 lines, including primary objective, research design, methods and procedures, main outcomes and results. Do not use abbreviations in the abstract.
Use the decimal system for sections, subsections and (at the most) sub-subsections, as exemplified in the headings of these instructions.
All abbreviations should be spelled out the first time they are introduced in text or references. Thereafter the abbreviation can be used.
Appendices
The editorial system includes:
1. Manuscript, which should contain the full text with figures, tables and signatures to them where they are placed.
2. Figures, tables and signatures to them as separate files.
2.1. Formulae, equations and units
The formulas should be written in Microsoft Equation and MathType with the possibility of editing (not as graphics).
Formulae and equations should be typed on separate lines and numbered consecutively in parentheses on the right side (1) . . . (n). Vectors must be indicated as such. Size of symbols should be kept uniform for all equations in the manuscript. Formulae and equations should be referred to in the text as follows: Eq. (1).
Numbers and units must be separated by a space, e.g. 5.5 wt.%, 273.15 K, 1013 MPa, etc. The only exception are angle degrees, e.g. 90°.
The authors can make movie files up to 100 MB in MP4 format.
The author at the first reference (Movie 1. Click here) should with the Click here command connect the web address with the place of uploading the movie (hyperlink) and at the end of the article provide a list of hyperlinks (samples: Movie 1, hyperlink, movie no 2, hyperlink ......).
2.4. Tables
2.5. References
Archives of Metallurgy and Materials is covered by the following
services:
Arianta, Baidu Scholar, BazTech, Celdes, Chemical Abstracts Service
(CAS) - CAplus, Clarivate Analytics (formerly Thomson Reuters) - Current
Contents/Engineering, Computing, and Technology, Clarivate Analytics
(formerly Thomson Reuters) - Journal Citation Reports/Science Edition,
Clarivate Analytics (formerly Thomson Reuters) - Materials Science
Citation Index, Clarivate Analytics (formerly Thomson Reuters) - Science
Citation Index Expanded, CNKI Scholar (China National Knowledge
Infrastructure), CNPIEC, DOAJ (Directory of Open Access Journals), EBSCO
(relevant databases), EBSCO Discovery Service, Elsevier - SCOPUS,
Genamics JournalSeek, Google Scholar, Index Copernicus, J-Gate,
JournalTOCs, KESLI-NDSL (Korean National Discovery for Science Leaders),
Microsoft Academic, Naviga (Softweco), Primo Central (ExLibris),
ProQuest (relevant databases), ReadCube, ResearchGate, SCImago (SJR),
Sherpa/RoMEO, Summon (Serials Solutions/ProQuest), TDNet, TEMA Technik
und Management, Ulrich's Periodicals Directory/ulrichsweb, WanFang Data,
WorldCat (OCLC)
Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
oai:journals.pan.pl:112991 ; DOI: 10.24425/amm.2019.129463 ; e-ISSN 2300-1909
Archives of Metallurgy and Materials; 2019; vol. 64; No 3; 869-873
Archive of Metallurgy and Materials is an open access journal with all content available with no charge in full text version.
Articles are printed in an open access and distributed under the terms of the Creative Commons Attribution-NonCommercial (CC BY-NC 4.0, https://creativecommons.org/licenses/by-nc/4.0/.).
This license allows authors to copy and redistribute the material in any medium or format, remix, transform, and build upon the material.
Authors may not use the material for commercial purposes. However, this condition does not include dependent works (they may be covered by another license).
19 sie 2024
17 cze 2019
$number.toString().replaceAll("[0-9](?=(?:[0-9]{3})+(?![0-9]))", "$0 ")
780
https://journals.pan.pl/publication/129463
| Nazwa wydania | Data |
|---|---|
| 10 | 19 sie 2024 |
pl
en
