Almost all matter in our Universe exists in the form of plasma. Although it’s not easy to generate on Earth, it has a vast range of applications in medicine, biotechnology, farming and industry.

This article deals with the testing of surface layers produced on technical titanium Ti99.2 under glow discharge conditions. In order to determine the effect of process temperature on the produced surface layers, nitriding processes were carried out at 700°C and 800°C and for 3 and 5 hours. The research results on evaluating the properties of the obtained surface layers and the characterization of their morphology were presented. The impact of the adopted nitriding process variant on the quality of the obtained layers was evaluated. It was demonstrated that the use of the supplementary potential during the ion nitriding process reduces the unwanted edge effect, which results in a significant increase in the homogeneity of the nitrided layers and improves the functional properties of the technical titanium Ti99.2.

The presented work gives an overview on simulation and experimental results of the power supply parameters’ influence on DBD discharge uniformity. The proposed study is about the use of quasi-pulsed, power electronic power supply and a saturable inductor in series with the discharge cell [1]. The simulation results are presented with a parallel DBD reactor model with linear critical voltage distribution. A more uniform current waveform is observed, however, due to small reactor capacitances no streamer formation could be verified in calculations. An experimental test stand was prepared with a double dielectric barrier discharge arrangement. The experimental results are presented with regard to the electrical oscilloscope waveforms and ICCD camera imaging. A more homogenous plasma was observed in the case of saturable inductor with saturation current set at the point of discharge formation. Two possible mechanisms are connected with this phenomenon – inductive element current support during discharge and/or current rise-time limitation [1].

Filtering nonwovens produced with melt-blown technology are one of the most basic materials used in the construction of respiratory protective equipment (RPE) against harmful aerosols, including bio- and nanoaerosols. The improvement of their filtering properties can be achieved by the development of quasi-permanent electric charge on the fibres. Usually corona discharge method is utilized for this purpose. In the presented study, it was assumed that the low-temperature plasma treatment could be applied as an alternative method for the manufacturing of conventional electret nonwovens for the RPE construction. Low temperature plasma treatment of polypropylene nonwovens was carried out with various process gases (argon, nitrogen, oxygen or air) in a wide range of process parameters (gas flow velocity, time of treatment and power supplied to the reactor electrodes). After the modification, nonwovens were evaluated in terms of filtration efficiency of paraffin oil mist. The stability of the modification results was tested after 12 months of storage and after conditioning at elevated temperature and relative humidity conditions. Moreover, scanning electron microscopy and ATR-IR spectroscopy were used to assess changes in surface topography and chemical composition of the fibres. The modification of melt-blown nonwovens with nitrogen, oxygen and air plasma did not result in a satisfactory improvement of the filtration efficiency. In case of argon plasma treatment, up to 82% increase of filtration efficiency of paraffin oil mist was observed in relation to untreated samples. This effect was stable after 12 months of storage in normal conditions and after thermal conditioning in (70 ± 3)°C for 24 h. The use of low-temperature plasma treatment was proven to be a promising improvement direction of filtering properties of nonwovens used for the protection of respiratory tract against harmful aerosols.

In this work, the change of the structure and microhardness of Ti6Al4V titanium alloy after remelting and remelting with SiC alloing by electric arc welding (GTAW method) was studied. The current intensity equal 100 A and fixed scan speed rate equal 0,2 m/min has been used to remelting surface of the alloy. Change of structure were investigated by optical and scanning electron microscopy. Microhardness test showed, that the remelting of the surface does not change the hardness of the alloy. Treated by GTAW SiC alloying leads to the formation of hard (570 HV0, 1) surface layer with a thickness of 2 mm. The resulting surface layer is characterized by diverse morphology alloyed zone. The fracture of alloy after conventional heat treatment, similarly to fracture after remelting with GTAW is characterized by extremely fine dimples of plastic deformation. In the alloyed specimens the intergranular and crystalline fracture was identified.

The amorphous Mg-based alloys may be used as metallic biomaterials for resorbable orthopedic implants. The Mg-Zn-Ca metallic glasses demonstrate variable in time degradation rate in simulated body fluid. In this work the Mg₆₆Zn₃₀Ca₄ alloy was chosen as a substrate for coatings. This paper reports on the surface modification of a Mg₆₆Zn₃₀Ca₄ metallic glass by plasma electrolytic oxidation (PEO). The structure characterization of uncoated Mg₆₆Zn₃₀Ca₄ alloy was performed by using TEMand XRD method. The immersion tests of coated and uncoated Mg₆₆Zn₃₀Ca₄ alloy were carried out in Ringer’s solutionat 37°C. The volume of released hydrogen by immersion tests was determined. The coatings structure and chemical composition after immersion tests by SEM/EDS were studied. Based on SEM images of surface structure samples, immersion tests results and hydrogen evolution measurement was proposed the course of corrosion process in Ringer’s solution for Mg-based metallic glasses with PEO coating. Results of immersion tests in Ringer’s solution allowed to determine the amount of evolved hydrogen in a function of time for Mg₆₆Zn₃₀Ca₄ metallic glass and sample with PEO coating. In comparison to the non-coated Mg₆₆Zn₃₀Ca₄ alloy, the sample with PEO layer showed a significantly decreased hydrogen evolution volume.

One of the ways to decrease thermal conductivity is nano structurization. Cobalt triantimonide (CoSb3) samples with added indium or tellurium were prepared by the direct fusion technique from high purity elements. Ingots were pulverized and re-compacted to form electrodes. Then, the pulsed plasma in liquid (PPL) method was applied. All materials were consolidated using rapid spark plasma sintering (SPS). For the analysis, methods such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM) with a laser flash apparatus (LFA) were used. For density measurement, the Archimedes’ method was used. Electrical conductivity was measured using a standard four-wire method. The Seebeck coefficient was calculated to form measured Seebeck voltage in the sample placed in a temperature gradient. The preparation method allowed for obtaining CoSb3 nanomaterial with significantly lower thermal conductivity (10 Wm^–1K^–1 for pure CoSb₃ and 3 Wm^–1K^–1 for the nanostructured sample in room temperature (RT)). The size of crystallites (from SEM observations) in the powders prepared was about 20 nm, joined into larger agglomerates. The Seebeck coefficient, α, was about –200 µVK^–1 in the case of both dopants, In and Te, in microsized material and about –400 µVK^–1 for the nanomaterial at RT. For pure CoSb3, α was about 150 µVK^–1 and it stood at –50 µVK^–1 for nanomaterial at RT. In bulk nanomaterial samples, due to a decrease in electrical conductivity and inversion of the Seebeck coefficient, there was no increase in ZT values and the ZT for the nanosized material was below 0.02 in the measured temperature range, while for microsized In-doped sample it reached maximum ZT = 0.7 in (600K).

This work reports the results of a study of Mo thin films synthesis by DC Pulsed Magnetron Sputtering method (PMS), operating at pulse main frequency of 100 kHz and modulated by the additional modulation frequency, driving in the range of 5-1000 Hz (modulated Pulse Magnetron Sputtering – mPMS). We have studied the influence of mPMS on plasma chemical reactions and mechanisms of layer growth using optical emission spectroscopy technique. Our experiment showed strong influence of mPMS method, on the morphology (scanning electron microscopy), phase composition (X-ray diffractometry) and electric properties (4-point probes method) of nanocrystalline and amorphous Mo films. From the utilitarian point of view, low value of resistivity – 43,2 μΩcm of synthesized Mo films predestines them as back contacts for thin solar cells CIGS. Our results revealed that additional modulation frequency should be considered as an important factor for optimization of films synthesis by means of PMS-based methods.

The mechanical behavior and the change of retained austenite of nanocrystalline Fe-Ni alloy have been investigated by considering the effect of various Ni addition amount. The nanocrystalline Fe-Ni alloy samples were rapidly fabricated by spark plasma sintering (SPS). The SPS is a well-known effective sintering process with an extremely short densification time not only to reach a theoretical density value but also to prevent a grain growth, which could result in a nanocrystalline structures. The effect of Ni addition on the compressive stress-strain behavior was analyzed. The variation of the volume fraction of retained austenite due to deformation was quantitatively measured by means of x-ray diffraction and microscope analyses. The strain-induced martensite transformation was observed in Fe-Ni alloy. The different amount of Ni influenced the rate of the strain-induced martensite transformation kinetics and resulted in the change of the work hardening during the compressive deformation.

The aim of this study was to analyse and identify specific buffalo seminal plasma proteins (SPPs) responsible for sperm cryotolerance during low temperature storage. Computer Assisted Sperm Analysis (CASA) of the motility and viability of buffalo spermatozoa was performed before freezing and after thawing. Two sample groups were formed – ejaculates with high cryotol- erance (group A) and low cryotolerance (group B). CASA demonstrated that the initial progres- sive motility after thawing of the spermatozoa in group A is significantly higher than in group B (p<0.001). Group B showed a significant increase in the percentage of static and non-progressive spermatozoa at 240 min, when compared to group A (p<0.05). SPPs, proteins in the cryoprotec- tive medium (PM) and proteins in the mixture of PM and SP were separated by High Perfor- mance Liquid Chromatography (HPLC). Comparative analysis of the chromatographic profiles was performed to identify specific proteins related to sperm cryotolerance. SPPs profiles showed 5 distinct protein peaks in both groups, ranging from 500 kDa to 50 Da. Chromatograms of group A and group B showed quantitative and qualitative differences in protein content. Chromato- grams of proteins in PM showed 11 well-expressed peaks. HPLC analysis of the mixtures of SPPs from the two groups and PM visualized the formation of a new bio-complex structure expressed by a protein peak specific for group A (7.674 min, AU 1.50). This protein peak can be referred as a phenotypic trait for buffalo ejaculates with high sperm cryotolerance.

In our recent study we demonstrated that the holding of fresh semen in fractionated seminal plasma (SP1, >40 kDa; SP2, <40 kDa), obtained by gel filtration chromatography, significantly improved the sperm quality characteristics following cryopreservation (Wasilewska-Sakowska et al. 2019). In this study we investigated the effect of post-thaw (PT) supplementation of fractionated SP (SP1 and SP2) on the survival of spermatozoa from boars with good and poor semen freezability, GSF and PSF, respectively. Two-dimensional polyacrylamide gel electrophoresis (2D-PAGE) analysis showed distinct differences in the protein profiles of SP1 and SP2 from boars with GSF or PSF regarding the number of protein spots. Sperm motility characteristics and the motion patterns, assessed using the computer-assisted sperm analysis (CASA) system, were markedly higher in PT semen supplemented with SP1 and SP2 from boars with GSF. Post-thaw supplementation of either SP1 or SP2 from boars with GSF significantly improved mitochondrial function, plasma membrane and acrosome integrity, and viability during storage. The findings of this study have confirmed that the presence of protective protein components in varying abundance in either fractionated SP from boars with good freezability ejaculates significantly improved the sperm survival following PT storage.

The aim of this study was to identify the proteoforms of albumin and kallikrein in stallion seminal plasma (SP), and to determine their correlations with sperm motility parameters. The experimental material consisted of ejaculates from 8 stallions, which were collected during the breeding and non-breeding seasons (BS and NBS, respectively). SP proteins were identified by 2-D PAGE and mass spectrometry (MALDI TOT/TOF MS). Sperm motility parameters were analyzed using the CASA system. Protein expression (integrated optical density-IOD) of albumin proteoforms 1 (ALB 1) and 2 (ALB 2) and kallikrein proteoforms 1 (KAL 1) and 2 (KAL 2) was correlated (p<0.05) with sperm motility parameters (total motility and progressive motility) during the BS. No significant correlations were found between the expression of albumin or kallikrein and sperm motility parameters during the NBS. The presence of correlations between the expression of ALB 1, ALB 2, KAL 1, KAL 2 and selected sperm motility parameters could suggest that the analyzed components of the SP belong to the group of fertility-associated pro- teins (FAPs).

In this work a review of investigations concerning interaction of intense extreme ultraviolet (EUV) and soft X-ray (SXR) pulses with matter is presented. The investigations were performed using laser-produced plasma (LPP) EUV/SXR sources based on a double stream gas puff target. The sources are equipped with dedicated collectors allowing for efficient focusing of the EUV/SXR radiation pulses. Intense radiation in a wide spectral range, as well as a quasi-monochromatic radiation can be produced. In the paper different kinds of LPP EUV/SXR sources developed in the Institute of Optoelectronics, Military University of Technology are described.

Radiation intensities delivered by the sources are sufficient for different kinds of interaction experiments including EUV/SXR induced ablation, surface treatment, EUV fluorescence or photoionized plasma creation. A brief review of the main results concerning this kind of experiments performed by author of the paper are presented. However, since the LPP sources cannot compete with large scale X-ray sources like synchrotrons, free electron lasers or high energy density plasma sources, it was indicated that some investigations not requiring extreme irradiation parameters can be performed using the small scale installations. Some results, especially concerning low temperature photoionized plasmas are very unique and could be hardly obtained using the large facilities.

We present spectral emission characteristics from laser-plasma EUV/SXR sources produced by irradiation of < 1 J energy laser pulse on eleven different double stream gas puff targets, with most intense electronic transitions identified in the spectral range from 1 nm to 70 nm wavelength which corresponds to photon energy from 18 eV to 1240 eV. The spectra were obtained using grazing incidence and transmission spectro- graphs from laser-produced plasma emission, formed by the interaction of a laser beam with a double stream gas puff target. Laser pulses with a duration of 4 ns and energy of 650 mJ were used for the experiment. We present the results obtained from three different spectrometers in the wavelength ranges of SXR (1–5.5 nm), SXR/EUV (4–15.5 nm), and EUV (10–70 nm). In this paper, detailed information about the source, gas targets under investigation, the experimental setup, spectral measurements and the results are presented and discussed. Such data may be useful for the identification of adequate spectral emissions from gasses in the EUV and SXR wavelength ranges dedicated to various experiments (i.e. broadband emission for the X-ray coherence tomography XCT) or may be used for verification of magnetohydrodynamic plasma codes.

The aim of the present study was to determine changes in oxidative status in plasma of sows during periparturient period using markers of lipid and protein peroxidation intensity. Plasma from 12 pregnant gilts collected on days 14 and 1 before parturition and on days 1, 7 and 14 postpartum was used in the study. As indicators of alterations in the oxidative status, plasma concentrations of thiobarbituric acid reactive substances (TBARS) and sulphydryl groups (SH groups) were measured spectrophotometrically, as well as plasma concentrations of bityrosine and formylokinurenine were determined by the spectrofluorimetric method. Compared to the 14th day antepartum, the concentration of TBARS increased significantly on day 1 postpartum and then decreased significantly on days 7 and 14 after parturition. The concentration of SH groups increased significantly on the last day before parturition and decreased significantly on day 14 postpartum. The concentration of bityrosine increased significantly on the last day before parturition and decreased significantly on days 7 and 14 postpartum. The concentration of formylokinurenine increased significantly on the last day before parturition, remained at this level on the first day after parturition and then decreased slightly on days 7 and 14 postpartum. These results indicate that during periparturient period in sows, especially around the parturition, the oxidative/antioxidative balance is disturbed, which leads to oxidative stress. Considering that oxidative stress is potentially harmful for mothers and neonates, this may be an important factor in the increased risk of diseases occurring during this period.