Applied sciences

Archive of Mechanical Engineering

Content

Archive of Mechanical Engineering | 2024 | vol. 71 | No 4

Download PDF Download RIS Download Bibtex

Abstract

This research presents an enhanced methodology for diagnosing bearing faults using Variational Mode Decomposition (VMD) based on L-Kurtosis analysis. The proposed method focuses on selecting optimal parameters for VMD to extract the mode containing the most information related to the fault. The selection of these parameters is based on comparing the energy ratio of each mode and the absolute difference in L-Kurtosis between the Intrinsic Mode Function (IMF) with the highest energy and the original signal. The extracted mode is further refined using a specified kurtosis rate threshold to ensure the most relevant significant modes are captured. The proposed methodology was tested using real fault data from the CWRU, XJTU-SY, and a real-world wind turbine dataset related to electric motors and wind turbine systems. The results demonstrated high accuracy in fault detection compared to other methods such as the Gini Index, correlation, and traditional decomposition techniques like EMD. Furthermore, due to the simple computational nature of the improved VMD method, it is faster and more efficient compared to methods that rely on complex calculations or frequency band analysis, making it suitable for applications requiring real-time, reliable fault diagnosis
Go to article

Authors and Affiliations

Abderrahmane Lakikza
1
ORCID: ORCID
Hocine Cheghib
1
ORCID: ORCID
Nabil Kahoul
1
ORCID: ORCID

  1. Electromechanical Systems Laboratory, Badji Mokhtar-Annaba University, Annaba, Algeria
Download PDF Download RIS Download Bibtex

Abstract

In this paper, a novel analytical approach is proposed to predict the performance and onset criteria of a three-stage double-acting thermoacoustic Stirling oscillator (TDTASO). First, a coupled dynamic-thermodynamic model justifying the behavior of TDTASO is presented, taking into account Schmidt's theory assumptions. Subsequently, the manipulation of the obtained governing equations reveals that the considered Stirling oscillator is a physical regulator system. Thus, the onset criteria, which are the necessary conditions for designing such oscillators, are assessed based on a new analytical method resulting from a regulator-like model. Accordingly, the onset temperature difference is predicted corresponding to different dimensions of the resonator section in the TDTASO. Next, the sensitivity of the TDTASO to the inconsistency of resonators' dimensions is investigated. The results show that increasing the length of the mismatched water column results in a higher frequency. Finally, a prototype TDTASO is constructed and experimentally evaluated. Accordingly, the oscillator frequency is measured 3.14 Hz corresponding to the onset temperature of 163 C and the resonator length of 0.52 m. The experimental data demonstrate the effectiveness of the proposed analytical scheme in predicting the necessary conditions for designing the TDTASO.
Go to article

Authors and Affiliations

Mohammad Hossein Sangdani
1
ORCID: ORCID
Alireza Tavakolpour-Saleh
1
ORCID: ORCID

  1. Department of Mechanical Engineering, Shiraz University of Technology, Shiraz, Iran
Download PDF Download RIS Download Bibtex

Abstract

The article focuses on the load spectrum of a lightweight unmanned aircraft. It examines the impact of load signal sampling frequency on the load spectrum derived from the load signal. The flight sessions followed two scenarios: a maneuvering flight causing a wide range of load factor variations and a calm photogrammetric flight. The recorded load signals from two types of sensors were initially rescaled into load factor time series, with an optional signal smoothing process. These series were then downsampled by selecting every nth term, resulting in load factor sequences recorded at a lower frequency. Next, all sequences were transformed into sequences of local extremes of the Load Levels, resulting from quantifying the operational load variability into 32 intervals. Two options were considered: without filtering or with filtering of sequential pairs of terms generating small Load Level increments. Subsequently, the Rainflow Counting algorithm was applied, producing 32x32 load half-cycle arrays. Based on these arrays, incremental load spectra were calculated. The study provides a detailed comparison of load spectra for different load signal sources and recording frequencies. Additionally, calculations of the fatigue life of a structural element subjected to various load spectra were performed, leading to the formulated conclusions.
Go to article

Authors and Affiliations

Mirosław Rodzewicz
1
ORCID: ORCID

  1. Warsaw University of Technology, Warsaw, Poland
Download PDF Download RIS Download Bibtex

Abstract

Flow control is studied to improve the aerodynamic performance of an aerofoil. A strategy for maintaining the near-wall flow structure with a given spatial scale, developed within the framework of interdisciplinary research, is used. The proposed active flow control method is based on the application of spanwise arrays of mechanical, thermal, or plasma vortex generators. The latter are found most versatile and efficient for the formulated goal. Aerodynamic coefficients measured in the specified wind tunnel are discussed for the 12.5% supercritical airfoil model. The model is controlled by the spanwise array of pulsating high-voltage plasma discharges. This multi-actuator system provides a sufficient number of control parameters such as pulse duration and repetition rate, the distance between the neighboring actuators (space scale of generated disturbances), and the plasma array location along the airfoil chord. Measurements in a range of Reynolds numbers of Rec=(3-7)x105 showed growth of a maximal lift coefficient CLmax up to 10% and the stall angle by 1.5°-3.5° accompanied by drag reduction up to 7%.
Go to article

Authors and Affiliations

Nina Yurchenko
1
ORCID: ORCID
Pavlo Vynogradskyy
1
ORCID: ORCID
Roman Pavlovskyy

  1. Institute of Hydromechanics, National Academy of Sciences of Ukraine, Laboratory for Advanced Aerodynamics and Interdisciplinary Research, Kyiv, Ukraine
Download PDF Download RIS Download Bibtex

Abstract

The impact of a simple trailing-edge plain flap on the aerodynamics of the SD7037 airfoil have been studied in this paper using computational fluid dynamics at Reynolds number of 3×105 across various low angles of attack and flap deflection angles. The computational model was evaluated by using Star CCM+ software with κ--ω SST turbulence and gamma transition model to solve Navier-Stokes equations. The accuracy of the computational model has been confirmed through comparison with experimental data, showing a high level of agreement at low angles of attack. The findings revealed that specific combinations of angles of attack and flap deflection angles could increase the lift-to-drag ratio by over 70% compared to baseline conditions, benefiting airfoil performance, particularly during takeoff. Some combinations, however, resulted in decreased performance and should be avoided. The results also showed that with the increase of either the angle of attack or the flap deflection angle, the pitching moment increased.
Go to article

Authors and Affiliations

Ahmed Tawfeeq Mustafa Ali Abed
1
ORCID: ORCID

  1. Department of Aeronautical Engineering, College of Engineering, University of Baghdad, Baghdad, Iraq
Download PDF Download RIS Download Bibtex

Abstract

This paper presents a mathematical model for the flow of micropolar fluid in a horizontal channel filled with an anisotropic porous medium, bounded by two parallel plates—where the upper plate is stationary, and the lower plate moves at a constant velocity. The flow, driven by both a constant pressure gradient and the movement of the lower plate, is governed by the Darcy-Brinkman equation. Using no-slip and no-spin boundary conditions, we analytically derive expressions for the velocity, microrotational velocity, and stress distributions. The study provides a graphical analysis of the flow behavior influenced by key parameters such as the Darcy number, porous medium anisotropy, anisotropy angle, and the micropolar fluid’s material parameters. Furthermore, the effects of the material parameters and Darcy number on shear stress and couple stress are thoroughly investigated. The findings have applications in modeling fluid flow in striated or fractured rock formations.
Go to article

Authors and Affiliations

Vineet Kumar Verma
1
ORCID: ORCID
Abdul Faiz Ansari
1
ORCID: ORCID

  1. Department of Mathematics and Astronomy, University of Lucknow, Lucknow-226007, India
Download PDF Download RIS Download Bibtex

Abstract

Textile composites can be manufactured utilizing both synthetic and natural fibers, such as Corypha gebanga fiber, being a viable option. The weaving of Corypha gebanga fiber with cotton thread in a plain weave configuration enables its application as a reinforcement material in textile composites involving a resin matrix. This research aims to investigate the mechanical characteristics of plain woven Corypha gebanga fiber textile fabric-reinforced polymer hybrid composites made from epoxy resin. This study utilized four different variations: a control group without any treatment, and three treatment groups using solutions with NaOH concentrations of 2.5%, 5%, and 7.5%. The result showed that NaOH concentrations above 2.5% seem to have a detrimental effect, as indicated by the gradual decrease in mechanical performance observed in the 5% and 7.5% NaOH-treated specimens. The decrease in tensile strength suggests that prolonged exposure to alkaline conditions leads to permanent alterations in the cellulose structure and morphology. The optimal concentration of NaOH for maximum mechanical performance enhancement is found to be 5%, which balances the removal of impurities and the avoidance of excessive fiber damage. Microscopy image analysis showed that fiber pullout occurred in all specimens tested that were cut in the direction of the warp during tensile testing. The onset of fracture was characterized by the resin breaking initially, followed by the fibers stretching and ultimately breaking.
Go to article

Authors and Affiliations

I Gusti Ngurah Nitya Santhiarsa
1
ORCID: ORCID
I Gusti Bagus Wijaya Kusuma
1
ORCID: ORCID
I Putu Lokantara
1
ORCID: ORCID
Ni Made Dwidiani
1
ORCID: ORCID
Si Putu Gede Gunawan Tista
1
ORCID: ORCID
I Gede Artha Negara
2

  1. Mechanical Engineering Department, Udayana University, Badung, Indonesia
  2. Mechanical Engineering Department, Bali State Polytechnic, Badung, Indonesia
Download PDF Download RIS Download Bibtex

Abstract

Exoskeletons of lower extremities are used mainly for gait treatment in physical rehabilitation. However, they are also capable of being involved in other types of exercises. Nevertheless, their structure needs to be adequately adjusted for such applications. To analyse approaches to that, this review paper investigates the mechanical designs of rehabilitation exoskeletons for lower extremities. The study seeks to identify best practices in designing and implementing these devices by analysing fifty-two articles. It covers aspects such as kinematic structures, materials used, types of drives, and the range of exercises. Standard design features include multiple degrees of freedom, primarily at the hip, knee, and ankle joints, and using lightweight materials to enhance mobility and reduce power consumption. The review also discusses the advantages of different driving systems. The findings provide valuable insights for developing effective and safe rehabilitation exoskeletons, contributing to improved patient outcomes in physiotherapy and rehabilitation settings.
Go to article

Authors and Affiliations

Piotr Falkowski
1 2
ORCID: ORCID
Krzysztof Zawalski
1
ORCID: ORCID
Jan Oleksiuk
1
ORCID: ORCID
Bazyli Leczkowski
1
ORCID: ORCID
Zbigniew Pilat
1
ORCID: ORCID
Mehmet Emin Aktan
3
ORCID: ORCID
Erhan Akdogan
4
ORCID: ORCID
Paweł Niedbalski
5
Vasfi Emre Omurlu
6
ORCID: ORCID
Michał Jarek
2
Mateusz Wawrzyniak
2
Maciej Mazowiec
2

  1. Łukasiewicz Research Network – Industrial Research Institute for Automation and Measurements PIAP, Poland
  2. Warsaw University of Technology, Poland
  3. Bartin University, Türkiye
  4. Yıldız Technical University, Türkiye
  5. Elmiko Biosignals, Poland
  6. 3LS, Türkiye

Instructions for authors

About the Journal
Archive of Mechanical Engineering is an international journal publishing works of wide significance, originality and relevance in most branches of mechanical engineering. The journal is peer-reviewed and is published both in electronic and printed form. Archive of Mechanical Engineering publishes original papers which have not been previously published in other journal, and are not being prepared for publication elsewhere. The publisher will not be held legally responsible should there be any claims for compensation. The journal accepts papers in English.

Archive of Mechanical Engineering is an Open Access journal. The journal does not have article processing charges (APCs) nor article submission charges.

Outline of procedures
  • To ensure that high scientific standards are met, the editorial office of Archive of Mechanical Engineering implements anti-ghost writing and guest authorship policy. Ghostwriting and guest authorship are indication of scientific dishonesty and all cases will be exposed: editorial office will inform adequate institutions (employers, scientific societies, scientific editors associations, etc.).
  • To maintain high quality of published papers, the editorial office of Archive of Mechanical Engineering applies reviewing procedure. Each manuscript undergoes crosscheck plagiarism screening. Each manuscript is reviewed by at least two independent reviewers.
  • Before publication of the paper, authors are obliged to send scanned copies of the signed originals of the declaration concerning ghostwriting, guest authorship and authors contribution and of the Open Access license.
Submission of manuscripts

The manuscripts must be written in one of the following formats:
  • TeX, LaTeX, AMSTeX, AMSLaTeX (recommended),
  • MS Word, either as standard DOCUMENT (.doc, .docx) or RICH TEXT FORMAT (.rtf).
All submissions to the AME should be made electronically via Editorial System – an online submission and peer review system at https://www.editorialsystem.com/ame. First-time users must create an Author’s account to obtain a user ID and password required to enter the system. All manuscripts receive individual identification codes that should be used in any correspondence with regard to the publication process. For the authors already registered in Editorial System it is enough to enter their username and password to log in as an author. The corresponding author should be identified while submitting a paper – personal e-mail address and postal address of the corresponding author are required. Please note that the manuscript should be prepared using our LaTeX or Word template and uploaded as a PDF file.

If you experience difficulties with the manuscript submission website, please contact the Assistant to the Editor of the AME (ame.eo@meil.pw.edu.pl).

All authors of the manuscript are responsible for its content; they must have agreed to its publication and have given the corresponding author the authority to act on their behalf in all matters pertaining to publication. The corresponding author is responsible for informing the co-authors of the manuscript status throughout the submission, review, and production process.

Length and arrangement

Papers (including tables and figures) should not exceed in length 25 pages of size 12.6 cm x 19.5 cm (printing area) with a font size of 11 pt. For manuscript preparation, the Authors should use the templates for Word or LaTeX available at the journal webpage. Please notice that the final layout of the article will be prepared by the journal's technical staff in LaTeX. Articles should be organized into the following sections:
  • List of keywords (separated by commas),
  • Full Name(s) of Author(s), Affiliation(s), Corresponding Author e-mail address,
  • Title,
  • Abstract,
  • Main text,
  • Appendix,
  • Acknowledgments (if applicable),
  • References.
Affiliations should include department, university, city and country. ORCID identifiers of all Authors should be added.
We suggest the title should be as short as possible but still informative.

An abstract should accompany every article. It should be a brief summary of significant results of the paper and give concise information about the content of the core idea of the paper. It should be informative and not only present the general scope of the paper, but also indicate the main results and conclusions. An abstract should not exceed 200 words.

Please follow the general rules for writing the main text of the paper:
  • use simple and declarative sentences, avoid long sentences, in which the meaning may be lost by complicated construction,
  • divide the main text into sections and subsections (if needed the subsections may be divided into paragraphs),
  • be concise, avoid idle words,
  • make your argumentation complete; use commonly understood terms; define all nonstandard symbols and abbreviations when you introduce them;
  • explain all acronyms and abbreviations when they first appear in the text;
  • use all units consistently throughout the article;
  • be self-critical as you review your drafts.
The authors are advised to use the SI system of units.

Artwork/Equations/Tables

You may use line diagrams and photographs to illustrate theses from your text. The figures should be clear, easy to read and of good quality (300 dpi). The figures are preferred in a vector format (bitmap formats are acceptable, but not recommended). The size of the figures should be adequate to their contents. Use 8-9pt font size of the text within the figures.

You should use tables only to improve conciseness or where the information cannot be given satisfactorily in other ways. Tables should be numbered consecutively and referred to within the text by numbers. Each table should have an explanatory caption which should be as concise as possible. The figures and tables should be inserted in the text file, where they are mentioned.

Displayed equations should be numbered consecutively using Arabic numbers in parentheses. They should be centered, leaving a small space above and below to separate it from the surrounding text.

Footnotes/Endnotes/Acknowledgements

We encourage authors to restrict the use of footnotes. Information concerning research grant support should appear in a separate Acknowledgements section at the end of the paper. Acknowledgements of the assistance of colleagues or similar notes of appreciation should also appear in the Acknowledgements section.

References
References should be numbered and listed in the order that they appear in the text. References indicated by numerals in square brackets should complete the paper in the following style:

Books:
[1] R.O. Author. Title of the Book in Italics. Publisher, City, 2018.

Articles in Journals:
[2] D.F. Author, B.D. Second Author, and P.C. Third Author. Title of the article. Full Name of the Journal in Italics, 52(4):89–96, 2017. doi: 1234565/3554. (where means: 52 – volume; 4 – number or issue; 89–96 – pages, and 1234565/3554 – doi number (if exists).)

Theses:
[3] W. Author. Title of the thesis. Ph.D. Thesis, University, City, Country, 2010.

Conference Proceedings:
[4] H. Author. Title of the paper. In Proc. Conference Name in Italics, pages 001–005, Conference Place, 10-15 Jan. 2015. doi: 98765432/7654vd.

English language

Archive of Mechanical Engineering is published in English. Make sure that your manuscript is clearly and grammatically written. The content should be understandable and should not cause any confusion to the readers, including the reviewers. After accepting the manuscript for a publication in the AME, we offer a free language check service, for correcting small language mistakes.

Submission of Revised Articles

When revision of a manuscript is requested, authors are expected to deliver the revised version of the manuscript as soon as possible. The manuscript should be uploaded directly to the Editorial System as an answer to the Editor's decision, and not as a new manuscript. If it is the 1st revision, the authors are expected to return revised manuscript within 60 days; if it is the 2nd revision, the authors are expected to return revised manuscript within 14 days. Additional time for resubmission must be requested in advance. If the above mentioned deadlines are not met, the manuscript may be treated as a new submission.

Outline of the Production Process

Once an article has been accepted for publication, the manuscript is transferred into our production system to be language-edited and formatted. Language/technical editors reserve the privilege of editing manuscripts to conform with the stylistic conventions of the journal. Once the article has been typeset, PDF proofs are generated so that authors can approve all editing and layout.

Proofreading

Proofreading should be carried out once a final draft has been produced. Since the proofreading stage is the last opportunity to correct the article to be published, the authors are requested to make every effort to check for errors in their proofs before the paper is posted online. Authors may be asked to address remarks and queries from the language and/or technical editors. Queries are written only to request necessary information or clarification of an unclear passage. Please note that language/technical editors do not query at every instance where a change has been made. It is the author's responsibility to read the entire text, tables, and figure legends, not just items queried. Major alterations made will always be submitted to the authors for approval. The corresponding author receives e-mail notification when a PDF is available and should return the comments within 3 days of receipt. Comments must be uploaded to Editorial System.

Reviewers


The Editorial Board of the Archive of Mechanical Engineering (AME) sincerely expresses gratitude to the following individuals who devoted their time to review papers submitted to the journal. Particularly, we express our gratitude to those who reviewed papers several times.

List of reviewers in 2023

Sara I. ABDELSALAM – University of California Riverside, United States
M. ARUNA – Liwa College of Technology, United Arab Emirates
Krzysztof BADYDA – Warsaw University of Technology, Poland
Nathalie BÄSCHLIN – Kunstmuseum Bern, Germany
Joanna BIJAK – Silesian University of Technology, Gliwice, Poland
Tomas BODNAR – The Czech Academy of Sciences, Prague, Czech Republic
Dariusz BUTRYMOWICZ – Białystok University of Technology, Poland
Suleyman CAGAN – Mechanical Engineering, Mersin University, Turkey
Claudia CASAPULLA – University of Naples Federico II, Italy
Peng CHEN – Northwestern Polytechnical University, Xi’an, China
Yao CHENG – Southwest Jiaotong University, Chengdu, China
Jan de JONG – University of Twente, Netherlands
Mariusz DEJA – Gdańsk University of Technology, Poland
Jerzy EJSMONT – Gdańsk University of Technology, Poland
İsmail ESEN – Karabuk University, Turkey
Pedro Javier GAMEZ-MONTERO – Universitat Politecnica de Catalunya, Spain
Aman GARG – National Institute of Technology, Kurukshetra, India
Michał HAĆ – Warsaw University of Technology, Poland
Satoshi ISHIKAWA – Kyushu University, Japan
Jacek JACKIEWICZ – Kazimierz Wielki University, Bydgoszcz, Poland
Krzysztof JAMROZIAK – Wrocław University of Technology, Poland
Hong-Lae JANG – Changwon National University, Korea (South)
Łukasz JANKOWSKI – Institute of Fluid-Flow Machinery, PAS, Gdansk, Poland
Albizuri JOSEBA – University of the Basque Country, Spain
Łukasz KAPUSTA – Warsaw University of Technology, Poland
Dariusz KARDAŚ – Institute of Fluid-Flow Machinery, PAS, Gdansk, Poland
Panagiotis KARMIRIS-OBRATAŃSKI – AGH University of Science and Technology, Cracow, Poland
Sivakumar KARTHIKEYAN – SRM Nagar
Tarek KHELFA – Hunan University of Humanities Science and Technology, China
Sven-Joachim KIMMERLE – Universität der Bundeswehr München, Germany
Thomas KLETSCHKOWSKI – HAW Hamburg, Germany
Piotr KLONOWICZ – Institute of Fluid-Flow Machinery, PAS, Gdansk, Poland
Vladis KOSSE – Queensland University of Technology, Australia
Mariusz KOSTRZEWSKI – Warsaw University of Technology, Poland
Maria KOTELKO – Lodz University of Technology, Poland
Michał KOWALIK – Warsaw University of Technology, Poland
Zbigniew KRZEMIANOWSKI – Institute of Fluid-Flow Machinery, Gdańsk, Poland
Slawomir KUBACKI – Warsaw University of Technology, Poland
Mieczysław KUCZMA – Poznan University of Technology, Poland
Waldemar KUCZYŃSKI – The Koszalin University of Technology, Poland
Rafał KUDELSKI – AGH University of Science and Technology, Cracow, Poland
Rajesh KUMAR – Sant Longowal Institute of Engineering and Technology, India
Mustafa KUNTOĞLU – Selcuk University, Turkey
Anna LEE – Pohang University of Science and Technology, South Korea, Korea (South)
Guolong LI – Chongqing University, China
Luxian LI – Xi'an Jiaotong University, China
Yingchao LI – Ludong University, Yantai, China
Xiaochuan LIN – Nanjing Tech University, China
Zhihong LIN – HuaQiao University, China
Yakun LIU – Massachusetts Institute of Technology, United States
Jinjun LU – Northwest University, Xiʼan, China
Paweł MACIĄG – Warsaw University of Technology, Poland
Paweł MALCZYK – Warsaw University of Technology, Poland
Emil MANOACH – Bulgarian Academy of Sciences, Sofia, Bulgaria
Mihaela MARIN – “Dunărea de Jos” University of Galati, Romania
Miloš MATEJIĆ – University of Kragujevac, Serbia
Krzysztof MIANOWSKI – Warsaw University of Technology, Poland
Tran MINH TU – Hanoi University of Civil Engineering, Viet Nam
Farhad Sadegh MOGHANLOU – University of Mohaghegh Ardabili, Ardabil, Iran
Mohsen MOTAMEDI – University of Isfahan, Iran
Adis MUMINOVIC – University of Sarajevo, Bosnia and Herzegovina
Mohamed NASR – National Research Centre, Giza, Egypt
Huu-That NGUYEN – Nha Trang University, Viet Nam
Tan-Luy NGUYEN – Ho Chi Minh City University of Technology, Viet Nam
Viorel PALEU – Gheorghe Asachi Technical University of Iasi, Romania
Nicolae PANC – Technical University of Cluj-Napoca, Romania
Marcin PĘKAL – Warsaw University of Technology, Poland
Van Vinh PHAM – Le Quy Don Technical University, Hanoi, Viet Nam
Vaclav PISTEK – Brno University of Technology, Czech Republic
Paweł PYRZANOWSKI – Warsaw University of Technology, Poland
Lei QIN – Beijing Information Science & Technology University, China
Milan RACKOV – University of Novi Sad, Serbia
Yuriy ROMASEVYCH – National University of Life and Environmental Sciences of Ukraine, Kiev, Ukraine
Artur RUSOWICZ – Warsaw University of Technology, Poland
Andrzej SACHAJDAK – Silesian University of Technology, Gliwice, Poland
Mirosław SEREDYŃSKI – Warsaw University of Technology, Poland
Maciej SUŁOWICZ – Cracow University of Technology, Poland
Biswajit SWAIN – National Institute of Technology, Rourkela, India
Tadeusz SZYMCZAK – Motor Transport Institute, Warsaw, Poland
Reza TAHERDANGKOO – Institute of Geotechnics, Freiberg, Germany
Rulong TAN – Chongqing University of Technology, China
Daniel TOBOŁA – Łukasiewicz Research Network - Cracow Institute of Technology, Poland
Milan TRIFUNOVIĆ – University of Niš, Serbia
Duong VU – Duy Tan University, Viet Nam
Shaoke WAN – Xi’an Jiaotong University, China
Dong WEI – Northwest A&F University, Yangling , China
Marek WOJTYRA – Warsaw University of Technology, Poland
Mateusz WRZOCHAL – Kielce University of Technology, Poland
Hugo YAÑEZ-BADILLO – TecNM: Tecnológico de Estudios Superiores de Tianguistenco, Mexico
Guichao YANG – Nanjing Tech University, China
Xiao YANG – Chongqing Technology and Business University, China
Yusuf Furkan YAPAN – Yildiz Technical University, Turkey
Luhe ZHANG – Chongqing University, China
Xiuli ZHANG – Shandong University of Technology, Zibo, China

List of reviewers in 2022
Isam Tareq ABDULLAH – Middle Technical University, Baghdad, Iraq
Ahmed AKBAR – University of Technology, Iraq
Nandalur AMER AHAMMAD – University of Tabuk, Saudi Arabia
Ali ARSHAD – Riga Technical University, Latvia
Ihsan A. BAQER – University of Technology, Iraq
Thomas BAR – Daimler AG, Stuttgart, Germany
Huang BIN – Zhejiang University, Zhoushan, China
Zbigniew BULIŃSKI – Silesian University of Technology, Poland
Onur ÇAVUSOGLU – Gazi University, Turkey
Ali J CHAMKHA – Duy Tan University, Da Nang , Vietnam
Dexiong CHEN – Putian University, China
Xiaoquan CHENG – Beihang University, Beijing, China
Piotr CYKLIS – Cracow University of Technology, Poland
Agnieszka DĄBSKA – Warsaw University of Technology, Poland
Raphael DEIMEL – Berlin University of Technology, Germany
Zhe DING – Wuhan University of Science and Technology, China
Anselmo DINIZ – University of Campinas, São Paulo, Brazil
Paweł FLASZYŃSKI – Institute of Fluid-Flow Machinery, Gdańsk, Poland
Jerzy FLOYRAN – University of Western Ontario, London, Canada
Xiuli FU – University of Jinan, China
Piotr FURMAŃSKI – Warsaw University of Technology, Poland
Artur GANCZARSKI – Cracow University of Technology, Poland
Ahmad Reza GHASEMI– University of Kashan, Iran
P.M. GOPAL – Anna University, Regional Campus Coimbatore, India
Michał GUMNIAK – Poznan University of Technology, Poland
Bali GUPTA – Jaypee University of Engineering and Technology, India
Dmitriy GVOZDYAKOV – Tomsk Polytechnic University, Russia
Jianyou HAN – University of Science and Technology, Beijing, China
Tomasz HANISZEWSKI – Silesian University of Technology, Poland
Juipin HUNG – National Chin-Yi University of Technology, Taichung, Taiwan
T. JAAGADEESHA – National Institute of Technology, Calicut, India
Jacek JACKIEWICZ – Kazimierz Wielki University, Bydgoszcz, Poland
JC JI – University of Technology, Sydney, Australia
Feng JIAO – Henan Polytechnic University, Jiaozuo, China
Daria JÓŹWIAK-NIEDŹWIEDZKA – Institute of Fundamental Technological Research, Warsaw, Poland
Rongjie KANG – Tianjin University, China
Dariusz KARDAŚ – Institute of Fluid-Flow Machinery, Gdansk, Poland
Leif KARI – KTH Royal Institute of Technology, Sweden
Daria KHANUKAEVA – Gubkin Russian State University of Oil and Gas, Russia
Sven-Joachim KIMMERLE – Universität der Bundeswehr München, Germany
Yeong-Jin KING – Universiti Tunku Abdul Rahman, Malaysia
Kaushal KISHORE – Tata Steel Limited, Jamshedpur, India
Nataliya KIZILOVA – Warsaw University of Technology, Poland
Adam KLIMANEK – Silesian University of Technology, Poland
Vladis KOSSE – Queensland University of Technology, Australia
Maria KOTEŁKO – Lodz University of Technology, Poland
Roman KRÓL – Kazimierz Pulaski University of Technology and Humanities in Radom, Poland
Krzysztof KUBRYŃSKI – Airforce Institute of Technology, Warsaw, Poland
Mieczysław KUCZMA – Poznan University of Technology, Poland
Paweł KWIATOŃ – Czestochowa University of Technology, Poland
Lihui Lang – Beihang University, China
Rafał LASKOWSKI – Warsaw University of Technology, Poland
Guolong Li – Chongqing University, China
Leo Gu LI – Guangzhou University, China
Pengnan LI – Hunan University of Science and Technology, China
Nan LIANG – University of Toronto, Mississauga, Canada
Michał LIBERA – Poznan University of Technology, Poland
Wen-Yi LIN – Hungkuo Delin University of Technology, Taiwan
Wojciech LIPINSKI – Austrialian National University, Canberra, Australia
Linas LITVINAS – Vilnius University, Lithuania
Paweł MACIĄG – Warsaw University of Technology, Poland
Krishna Prasad MADASU – National Institute of Technology Raipur, Chhattisgarh, India
Trent MAKI – Amino North America Corporation, Canada
Marco MANCINI – Institut für Energieverfahrenstechnik und Brennstofftechnik, Germany
Piotr MAREK – Warsaw University of Technology, Poland
Miloš MATEJIĆ – University of Kragujevac, Serbia
Phani Kumar MEDURI – VIT-AP University, Amaravati, India
Fei MENG – University of Shanghai for Science and Technology, China
Saleh MOBAYEN – University of Zanjan, Iran
Vedran MRZLJAK – Rijeka University, Croatia
Adis MUMINOVIC – University of Sarajevo, Bosnia and Herzegovina
Mohamed Fawzy NASR – National Research Centre, Giza, Egypt
Paweł OCŁOŃ – Cracow University of Technology, Poland
Yusuf Aytaç ONUR – Zonguldak Bulent Ecevit University, Turkey
Grzegorz ORZECHOWSKI – LUT University, Lappeenranta, Finland
Halil ÖZER – Yıldız Technical University, Turkey
Muthuswamy PADMAKUMAR – Technology Centre Kennametal India Ltd., Bangalore, India
Viorel PALEU – Gheorghe Asachi Technical University of Iasi, Romania
Andrzej PANAS – Warsaw Military Academy, Poland
Carmine Maria PAPPALARDO – University of Salerno, Italy
Paweł PARULSKI – Poznan University of Technology, Poland
Antonio PICCININNI – Politecnico di Bari, Italy
Janusz PIECHNA – Warsaw University of Technology, Poland
Vaclav PISTEK – Brno University of Technology, Czech Republic
Grzegorz PRZYBYŁA – Silesian University of Technology, Poland
Paweł PYRZANOWSKI – Warsaw University of Technology, Poland
K.P. RAJURKARB – University of Nebraska-Lincoln, United States
Michał REJDAK – Institute of Chemical Processing of Coal, Zabrze, Poland
Krzysztof ROGOWSKI – Warsaw University of Technology, Poland
Juan RUBIO – University of Minas Gerais, Belo Horizonte, Brazil
Artur RUSOWICZ – Warsaw University of Technology, Poland
Wagner Figueiredo SACCO – Universidade Federal Fluminense, Petropolis, Brazil
Andrzej SACHAJDAK – Silesian University of Technology, Poland
Bikash SARKAR – NIT Meghalaya, Shillong, India
Bozidar SARLER – University of Lubljana, Slovenia
Veerendra SINGH – TATA STEEL, India
Wieńczysław STALEWSKI – Institute of Aviation, Warsaw, Poland
Cyprian SUCHOCKI – Institute of Fundamental Technological Research, Warsaw, Poland
Maciej SUŁOWICZ – Cracov University of Technology, Poland
Wojciech SUMELKA – Poznan University of Technology, Poland
Tomasz SZOLC – Institute of Fundamental Technological Research, Warsaw, Poland
Oskar SZULC – Institute of Fluid-Flow Machinery, Gdansk, Poland
Rafał ŚWIERCZ – Warsaw University of Technology, Poland
Raquel TABOADA VAZQUEZ – University of Coruña, Spain
Halit TURKMEN – Istanbul Technical University, Turkey
Daniel UGURU-OKORIE – Federal University, Oye Ekiti, Nigeria
Alper UYSAL – Yildiz Technical University, Turkey
Yeqin WANG – Syndem LLC, United States
Xiaoqiong WEN – Dalian University of Technology, China
Szymon WOJCIECHOWSKI – Poznan University of Technology, Poland
Marek WOJTYRA – Warsaw University of Technology, Poland
Guenter WOZNIAK – Technische Universität Chemnitz, Germany
Guanlun WU – Shanghai Jiao Tong University, China
Xiangyu WU – University of California at Berkeley, United States
Guang XIA – Hefei University of Technology, China
Jiawei XIANG – Wenzhou University, China
Jinyang XU – Shanghai Jiao Tong University,China
Jianwei YANG – Beijing University of Civil Engineering and Architecture, China
Xiao YANG – Chongqing Technology and Business University, China
Oguzhan YILMAZ – Gazi University, Turkey
Aznifa Mahyam ZAHARUDIN – Universiti Teknologi MARA, Shah Alam, Malaysia
Zdzislaw ZATORSKI – Polish Naval Academy, Gdynia, Poland
S.H. ZHANG – Institute of Metal Research, Chinese Academy of Sciences, China
Yu ZHANG – Shenyang Jianzhu University, China
Shun-Peng ZHU – University of Electronic Science and Technology of China, Chengdu, China
Yongsheng ZHU – Xi’an Jiaotong University, China

List of reviewers of volume 68 (2021)
Ahmad ABDALLA – Huaiyin Institute of Technology, China
Sara ABDELSALAM – University of California, Riverside, United States
Muhammad Ilman Hakimi Chua ABDULLAH – Universiti Teknikal Malaysia Melaka, Malaysia
Hafiz Malik Naqash AFZAL – University of New South Wales, Sydney, Australia
Reza ANSARI – University of Guilan, Rasht, Iran
Jeewan C. ATWAL – Indian Institute of Technology Delhi, New Delhi, India
Hadi BABAEI – Islamic Azad University, Tehran, Iran
Sakthi BALAN – K. Ramakrishnan college of Engineering, Trichy, India
Leszek BARANOWSKI – Military University of Technology, Warsaw, Poland
Elias BRASSITOS – Lebanese American University, Byblos, Lebanon
Tadeusz BURCZYŃSKI – Institute of Fundamental Technological Research, Warsaw, Poland
Nguyen Duy CHINH – Hung Yen University of Technology and Education, Hung Yen, Vietnam
Dorota CHWIEDUK – Warsaw University of Technology, Poland
Adam CISZKIEWICZ – Cracow University of Technology, Poland
Meera CS – University of Petroleum and Energy Studies, Duhradun, India
Piotr CYKLIS – Cracow University of Technology, Poland
Abanti DATTA – Indian Institute of Engineering Science and Technology, Shibpur, India
Piotr DEUSZKIEWICZ – Warsaw University of Technology, Poland
Dinesh DHANDE – AISSMS College of Engineering, Pune, India
Sufen DONG – Dalian University of Technology, China
N. Godwin Raja EBENEZER – Loyola-ICAM College of Engineering and Technology, Chennai, India
Halina EGNER – Cracow University of Technology, Poland
Fehim FINDIK – Sakarya University of Applied Sciences, Turkey
Artur GANCZARSKI – Cracow University of Technology, Poland
Peng GAO – Northeastern University, Shenyang, China
Rafał GOŁĘBSKI – Czestochowa University of Technology, Poland
Andrzej GRZEBIELEC – Warsaw University of Technology, Poland
Ngoc San HA – Curtin University, Perth, Australia
Mehmet HASKUL – University of Sirnak, Turkey
Michal HATALA – Technical University of Košice, Slovak Republic
Dewey HODGES – Georgia Institute of Technology, Atlanta, United States
Hamed HONARI – Johns Hopkins University, Baltimore, United States
Olga IWASINSKA – Warsaw University of Technology, Poland
Emmanuelle JACQUET – University of Franche-Comté, Besançon, France
Maciej JAWORSKI – Warsaw University of Technology, Poland
Xiaoling JIN – Zhejiang University, Hangzhou, China
Halil Burak KAYBAL – Amasya University, Turkey
Vladis KOSSE – Queensland University of Technology, Brisbane, Australia
Krzysztof KUBRYŃSKI – Air Force Institute of Technology, Warsaw, Poland
Waldemar KUCZYŃSKI – Koszalin University of Technology, Poland
Igor KURYTNIK – State Higher School in Oswiecim, Poland
Daniel LESNIC – University of Leeds, United Kingdom
Witold LEWANDOWSKI – Gdańsk University of Technology, Poland
Guolu LI – Hebei University of Technology, Tianjin, China
Jun LI – Xi’an Jiaotong University, China
Baiquan LIN – China University of Mining and Technology, Xuzhou, China
Dawei LIU – Yanshan University, Qinhuangdao, China
Luis Norberto LÓPEZ DE LACALLE – University of the Basque Country, Bilbao, Spain
Ming LUO – Northwestern Polytechnical University, Xi’an, China
Xin MA – Shandong University, Jinan, China
Najmuldeen Yousif MAHMOOD – University of Technology, Baghdad, Iraq
Arun Kumar MAJUMDER – Indian Institute of Technology, Kharagpur, India
Paweł MALCZYK – Warsaw University of Technology, Poland
Miloš MATEJIĆ – University of Kragujevac, Serbia
Norkhairunnisa MAZLAN – Universiti Putra Malaysia, Serdang, Malaysia
Dariusz MAZURKIEWICZ – Lublin University of Technology, Poland
Florin MINGIREANU – Romanian Space Agency, Bucharest, Romania
Vladimir MITYUSHEV – Pedagogical University of Cracow, Poland
Adis MUMINOVIC – University of Sarajevo, Bosnia and Herzegovina
Baraka Olivier MUSHAGE – Université Libre des Pays des Grands Lacs, Goma, Congo (DRC)
Tomasz MUSZYŃSKI – Gdansk University of Technology, Poland
Mohamed NASR – National Research Centre, Giza, Egypt
Driss NEHARI – University of Ain Temouchent, Algeria
Oleksii NOSKO – Bialystok University of Technology, Poland
Grzegorz NOWAK – Silesian University of Technology, Gliwice, Poland
Iwona NOWAK – Silesian University of Technology, Gliwice, Poland
Samy ORABY – Pharos University in Alexandria, Egypt
Marcin PĘKAL – Warsaw University of Technology, Poland
Bo PENG – University of Huddersfield, United Kingdom
Janusz PIECHNA – Warsaw University of Technology, Poland
Maciej PIKULIŃSKI – Warsaw University of Technology, Poland
T.V.V.L.N. RAO – The LNM Institute of Information Technology, Jaipur, India
Andrzej RUSIN – Silesian University of Technology, Gliwice, Poland
Artur RUSOWICZ – Warsaw University of Technology, Poland
Benjamin SCHLEICH – Friedrich-Alexander-Universität Erlangen-Nürnberg, Germany
Jerzy SĘK – Lodz University of Technology, Poland
Reza SERAJIAN – University of California, Merced, USA
Artem SHAKLEIN – Udmurt Federal Research Center, Izhevsk, Russia
G.L. SHI – Guangxi University of Science and Technology, Liuzhou, China
Muhammad Faheem SIDDIQUI – Vrije University, Brussels, Belgium
Jarosław SMOCZEK – AGH University of Science and Technology, Cracow, Poland
Josip STJEPANDIC – PROSTEP AG, Darmstadt, Germany
Pavel A. STRIZHAK – Tomsk Polytechnic University, Russia
Vadym STUPNYTSKYY – Lviv Polytechnic National University, Ukraine
Miklós SZAKÁLL – Johannes Gutenberg-Universität Mainz, Germany
Agnieszka TOMASZEWSKA – Gdansk University of Technology, Poland
Artur TYLISZCZAK – Czestochowa University of Technology, Poland
Aneta USTRZYCKA – Institute of Fundamental Technological Research, Warsaw, Poland
Alper UYSAL – Yildiz Technical University, Turkey
Gabriel WĘCEL – Silesian University of Technology, Gliwice, Poland
Marek WĘGLOWSKI – Welding Institute, Gliwice, Poland
Frank WILL – Technische Universität Dresden, Germany
Michał WODTKE – Gdańsk University of Technology, Poland
Marek WOJTYRA – Warsaw University of Technology, Poland
Włodzimierz WRÓBLEWSKI – Silesian University of Technology, Gliwice, Poland
Hongtao WU – Nanjing University of Aeronautics and Astronautics, China
Jinyang XU – Shanghai Jiao Tong University, China
Zhiwu XU – Harbin Institute of Technology, China
Zbigniew ZAPAŁOWICZ – West Pomeranian University of Technology, Szczecin, Poland
Zdzislaw ZATORSKI – Polish Naval Academy, Gdynia, Poland
Wanming ZHAI – Southwest Jiaotong University, Chengdu, China
Xin ZHANG – Wenzhou University of Technology, China
Su ZHAO – Ningbo Institute of Materials Technology and Engineering, China



This page uses 'cookies'. Learn more