Nauki Techniczne

Opto-Electronics Review

Zawartość

Opto-Electronics Review | 2018 | vol. 26 | No 2 |

Abstrakt

In this topic review the results of the X-band electron paramagnetic resonance (EPR) measurements of Mn, Co, Cr, Fe ions in YAlO3 (YAP) crystals and Fe ions in LiNbO3 (LNO) crystals and of chromium doped Bi12GeO20 (BGO) and Ca4GdO(BO3)3 single crystals, are presented. It is well known that the oxide crystals (for example:YAP, LNO, BGO) are one of the most widely used host materials for different optoelectronic applications. The nature of point defect of impurities and produced in the oxide crystal after irradiation by bismuth ions and after irradiation by the 235U ions with energy 9.47 MeV/u and fluency 5 × 1011 cm−1 is discussed. The latter is important for applications of these oxide crystal as laser materials.

Przejdź do artykułu

Autorzy i Afiliacje

I. Stefaniuk

Abstrakt

This paper presents the current state of a photoconductive semiconductor switch engineering. A photoconductive semiconductor switch is an electric switch with its principle of operation based on the phenomenon of photoconductivity. The wide application range, in both low and high-power devices or instruments, makes it necessary to take design requirements into account. This paper presents selected problems in the scope of designing photoconductive switches, taking into account, i.e. issues associated with the element trigger speed, uniform distribution of current density, thermal resistance, operational lifespan, and a high, local electric field generated at the location of electrodes. A review of semiconductor materials used to construct devices of this type was also presented.

Przejdź do artykułu

Autorzy i Afiliacje

E. Majda-Zdancewicz
M. Suproniuk
M. Pawłowski
M. Wierzbowski

Abstrakt

A method for frequency-multiplexed multi-sample gas sensing is presented. It enables measuring multiple samples placed simultaneously in the setup, without any optical or mechanical switching. Samples are measured using heterodyne detection and signal from each sensing path is encoded at different carrier frequency. Subsequently, a signal from particular sample is retrieved through heterodyne beatnote demodulation at unique frequency. This technique is particularly suitable for real-time calibration of the sensor through a sequential (or simultaneous) detection of three signals: from unknown sample, reference sample and baseline. Basic setup is demonstrated and proof-of-concept experiments are presented. Very good agreement with spectra measured using standard tunable diode absorption spectroscopy is obtained.

Przejdź do artykułu

Autorzy i Afiliacje

D. Tomaszewska
P. Jaworski
M. Nikodem

Abstrakt

In this attempt, Two Dimensional Photonic Crystal (2DPC) Quasi Square Ring Resonator (QSRR) based four channel demultiplexer is proposed and designed for Wavelength Division Multiplexing systems. The performance parameters of the demultiplexer such as transmission efficiency, passband width, line spacing, Q factor and crosstalk are investigated. The proposed demultiplexer is composed of bus waveguide, drop waveguide and QSRR. In the proposed demultiplexer, the output ports are arranged separately in odd and even number, where an odd number of ports are located on the right side and even number of ports are located on the left side of the bus waveguide that are used to reduce the channel interference or crosstalk. Further, the refractive index of rods around the center rod is increased linearly one to another in order to improve the signal quality. The resonant wavelengths of the proposed demultiplexer are of 1521.1 nm, 1522.0 nm, 1523.2 nm and 1524.3 nm, respectively. The footprint of the device is of 180.96 μm2. Then, a four channel point to point network is designed and the proposed four channel demultiplexer is implemented by replacing a conventional demultiplexer. Finally, functional parameters of the network, namely, BER, receiver sensitivity and Q factor are estimated by varying the link distance. This attempt could create new dimensions of research in the domain of photonic networks.

Przejdź do artykułu

Autorzy i Afiliacje

V. Kannaiyan
R. Savarimuthu
S.K. Dhamodharan

Abstrakt

In recent years, many scientific and industrial centres in the world developed a virtual reality systems or laboratories. The effect of user “immersion” into virtual reality in such systems is largely dependent on optical properties of the system. In this paper, problems of luminance distribution uniformity in CAVE-type virtual reality systems are analyzed. For better characterization of CAVE luminance nonuniformity corner and edge CAVE nonuniformity were introduced. Based on described CAVE-type virtual reality laboratory, named Immersive 3D Visualization Lab (I3DVL) just opened at the Gdansk University of Technology, luminance nonuniformity of the system is evaluated and discussed. Data collection of luminance distribution allows for software compensation of intensity distribution of individual images projected onto the screen (luminance non-uniformity minimization) in the further research.

Przejdź do artykułu

Autorzy i Afiliacje

A. Mazikowski

Abstrakt

Optoelectronic technology plays an important role in medical diagnosis. In the paper a review of some optoelectronic sensors for invasive and non-invasive human health test is presented. The main attention is paid on their basic operation principle and medical usefulness. The paper presents also own research related to developing of tools for human breath analysis. Breath sample unit and three gaseous biomarkers analyzer employing laser absorption spectroscopy designed for clinical diagnostics were described. The analyzer is equipped with sensors for CO, CH4 and NO detection. The sensors operate using multi-pass spectroscopy with wavelength modulation method (MUPASS-WMS) and cavity enhanced spectroscopy (CEAS).

Przejdź do artykułu

Autorzy i Afiliacje

Z. Bielecki
T. Stacewicz
J. Wojtas
J. Mikołajczyk
D. Szabra
A. Prokopiuk

Abstrakt

The behaviour of energy levels and optical spectra of a charged particle (electron or hole) confined within a potential well of ellipsoidal shape is investigated as a function of the shape-anisotropy parameter. If two energy levels of the same symmetry intersect in a perturbation-theory approximation, they move apart on direct diagonalization of the appropriate Hamiltonian. The intersection of the energy levels leads to a discontinuity of the corresponding dipole-moment matrix element. The discontinuity of matrix elements is not reflected in the behaviour of transition probabilities which are continuous functions of the shape-anisotropy parameter. The profiles of a spectral line emitted or absorbed by an ensemble of ellipsoidally shaped nanoparticles with a Gaussian distribution of size are calculated and discussed.

Przejdź do artykułu

Autorzy i Afiliacje

T. Kereselidze
T. Tchelidze
A. Devdariani

Abstrakt

In this paper, a low power highly sensitive Triple Metal Surrounding Gate (TM-SG) Nanowire MOSFET photosensor is proposed which uses triple metal gates for controlling short channel effects and III–V compound as the channel material for effective photonic absorption. Most of the conventional FET based photosensors that are available use threshold voltage as the parameter for sensitivity comparison but in this proposed sensor on being exposed to light there is a substantial increase in conductance of the GaAs channel underneath and, thereby change in the subthreshold current under exposure is used as a sensitivity parameter (i.e., Iillumination/IDark). In order to further enhance the device performance it is coated with a shell of AlxGa1-xAs which effectively passivates the GaAs surface and provides a better carrier confinement at the interface results in an increased photoabsorption. At last performance parameters of TM-SG Bare GaAs Nanowire MOSFET are compared with TM-SG core-shell GaAs/AlGaAs Nanowire MOSFET and the results show that Core-Shell structures can be a better choice for photodetection in visible region.

Przejdź do artykułu

Autorzy i Afiliacje

S.K. Sharma
A. Jain
B. Raj

Abstrakt

In this paper, detailed theoretical investigation on the frequency response and responsivity of a strain balanced SiGeSn/GeSn quantum well infrared photodetector (QWIP) is made. Rate equation and continuity equation in the well are solved simultaneously to obtain photo generated current. Quantum mechanical carrier transport like carrier capture in QW, escape of carrier from the well due to thermionic emission and tunneling are considered in this calculation. Impact of Sn composition in the GeSn well on the frequency response, bandwidth and responsivity are studied. Results show that Sn concentration in the GeSn active layer and applied bias have important role on the performance of the device. Significant bandwidth is obtained at low reverse bias voltage, e.g., 200 GHz is obtained at 0.28 V bias for a single Ge0.83Sn0.17 layer. Whereas, the maximum responsivity is of 8.6 mA/W at 0.5 V bias for the same structure. However, this can be enhanced by using MQW structure.

Przejdź do artykułu

Autorzy i Afiliacje

P. Pareek
M.K. Das
S. Kumar

Abstrakt

Power loss mechanisms in small area monolithic-interconnected photovoltaic modules (MIM) are described and evaluated. Optical and electrical losses are quantified and individual loss components are derived for loss mechanisms of small area radial (radius = 1 mm) pie-shaped six-segment GaAs MIM laser power converter. At low monochromatic homogeneous illumination (Glow = 1.8 W/cm2, λ0 = 809 nm) conversion efficiency of the cell, designed for a low irradiance, is reduced by 3.7%abs. due to isolation trench optical losses and by 7.0%abs. due to electrical losses (mainly perimeter recombination). Electrical losses in a device designed for a high irradiance, result in 18%abs. decrease of output power under homogeneous monochromatic illumination (Ghigh = 83.1 W/cm2, λ0 = 809 nm), while 11.6%abs. losses are attributed to optical reasons. Regardless the irradiance level, optical losses further increase if the device is illuminated with a Gaussian instead of an ideal flattop beam profile. In this case, beam spillage losses occur and losses due to isolation trenches and reflections from metallization are elevated. On top of that, additional current mismatch losses occur, if individual MIM’s segments are not equally illuminated. For the studied device, a 29 μm off center misalignment of a Gaussian shaped beam (with 1% spillage) reduces the short circuit current Isc by 10%abs. due to the current mismatch between segments.

Przejdź do artykułu

Autorzy i Afiliacje

R. Kimovec
H. Helmers
A.W. Bett
M. Topič

Abstrakt

Four dye-sensitized solar cell devices are designed and fabricated based on natural dyes extracted from Celosia Cristata, Saffron, Cynoglossum, and eggplant peel, as photosensitizers. The UV–vis technique has been served to determine maximum absorption of natural extract and pre-dyed photoanode. The Fourier transform infrared (FT-IR) was employed to cover the presence of functional groups. The cyclic voltammetry method has been employed to assess the possibility of charge transfer from dried natural dyes to the photoelectrode. The performance of natural-based dye-sensitized solar cells is determined subsequently. The highest power conversion efficiency was ca. 1.38%, which belonged to Celosia Cristata extract. The devices were examined for higher efficiencies, individually, co-sensitized arrangement and/or in tandem with each other.

Przejdź do artykułu

Autorzy i Afiliacje

M. Hosseinnezhad
S. Rouhani
K. Gharanjig

Abstrakt

Photoactive nanofilled nematic is proposed. Stable three-component photoresponsive nanocomposite was prepared from photo-insensitive nanofilled nematic by inclusion of 3 wt.% azobenzene-containing photoactive mesogen 4-(4′-ethoxyphenylazo)phenyl hexanoate (EPH). The host nanofilled nematic was produced from the room-temperature nematic liquid crystal 4-n-heptyl cyanobiphenyl (7CB) and 3 wt.% filler of Aerosil 300 hydrophilic silica nanospheres of size 7 nm. Apparent effect of stimulation with a relatively weak continuous illumination by UV light (375 nm wavelength) takes place for both the alternating-current electric field-dependent optical transmittance and the electro-optic amplitude-frequency modulation by thin films (25 µm thick) of the EPH/aerosil/7CB nanocomposite. The light-stimulated electro-optics of EPH-doped aerosil/7CB films and the corresponding reversible light control are achieved through trans-cis-trans photoisomerization of the photoactive agent EPH. As such, the initial electro-optical response of the studied photoactive nanocomposites is recovered with continuous blue-light illumination. The examined EPH/aerosil/7CB nanocomposites exhibit photo-controllable electro-optical response that is of practical interest.

Przejdź do artykułu

Autorzy i Afiliacje

Georgi B. Hadjichristov
Yordan G. Marinov
Alexander G. Petrov
Subbarao Krishna Prasad

Abstrakt

A modified optical fibre based Mach-Zehnder interferometer was applied as a sensor to detect wiretapping in long transmission optical fibre lines. The signal consisting of short pulses (around 1 ns) was launched to the input of the interferometer based on the polarization maintaining fibres and polarization elements. When the sensing line was undisturbed, detectors registered only a single pulse. The additional two side pulses appear, if the wiretapping attempt took place. For robust detection of any alarm situation we proposed two-criteria algorithm to minimize false alarm rate. Moreover, slow environmental fluctuations were continuously monitored and compensated by polarization controllers. We measured frequency characteristics of the sensor and performed a hundred wiretapping attempts, which proved high performance of the sensor.

Przejdź do artykułu

Autorzy i Afiliacje

M. Życzkowski
M. Karol

Abstrakt

We demonstrate MW-level, single resonance optical parametric oscillator, based on KTP Type-II crystal with noncritical phase-matching. The OPO is pumped by electro-optically Q-switched Nd:YAG slab laser providing 55 mJ of pulse energy. At the output, we achieved 28 mJ of signal pulse energy at 1.57 μm with 51% conversion efficiency, corresponding to 1.4 MW of peak power.

Przejdź do artykułu

Autorzy i Afiliacje

M. Kaskow
L. Gorajek
W. Zendzian
J. Jabczynski

Redakcja

Opto-Electronics Review - Editorial Board

Editor-in-Chief:
L. R. JAROSZEWICZ, Military University of Technology, Warsaw, Poland

Deputy Editor-in Chief:
P. MARTYNIUK, Military University of Technology, Warsaw, Poland


Board of Co-editors:

Optical Design and Applications
V.O. ANGELSKY, Chernivtsi National University, Chernivtsi, Ukraine

Image Processing
M. JÓŹWIK, Warsaw University of Technology, Warsaw, Poland

Metamaterials
T. ANTOSIEWICZ, Warsaw University, Warsaw, Poland

Modelling of Optoelectronic Devices. Semiconductor Lasers
M. DEMS, Łódź Technical University, Łódź, Poland

Optoelectronics Materials
D. DOROSZ, AGH University of Science and Technology, Cracow, Poland

Micro-Opto-Electro-Mechanical Systems
T.P. GOTSZALK, Wrocław University of Technology, Wrocław, Poland

Infrared Physics and Technology <
M. KOPYTKO, Military University of Technology, Warsaw, Poland

Technology and Fabrication of Optoelectronic Devices
J. MUSZALSKI, Institute of Electron Technology, Warsaw, Poland

Photonic Crystals
K. PANAJOTOV, Vrije Universiteit Brussels, Brussels, Belgium

Laser Physics, Technology and Applications
J. ŚWIDERSKI, Warsaw University of Technology, Warsaw, Poland

Optical Sensors and Applications
M. ŚMIETANA, Warsaw University of Technology, Warsaw, Poland

Photovoltaics
A. IWAN, Military Institute of Engineer Technology, Wroclaw, Poland

Biomedical Optics and Photonics
A. LIEBERT, Institute of Biocybernetics and Biomedical Engineering, Warsaw, Poland


International Editorial Advisory Board


D. BIMBERG, Technische Universitaet Berlin, Berlin, Germany

F. CAPASSO, Harvard University, Cambridge, USA

A.I. DIROCHKA, Production Center ORION, Moscow, Russia

P.G. ELISEEV, University of New Mexico, Albuquerque, USA

P. HARING−BOLIVAR, University of Siegen, Siegen, Germany

M. HENINI, University of Nottingham, Nottingham, England

B. JASKORZYNSKA, Royal Institute of Technology, Kista, Sweden

M. KIMATA, Ritsumeikan University, Shiga, Japan

R. KLETTE, University of Auckland, Auckland, New Zealand

S. KRISHNA, University of New Mexico, Albuquerque, USA

H.C. LIU, Shanghai Jiao Tong University, Shanghai, China

J. MISIEWICZ, Wrocław University of Technology, Wrocław, Poland

E. OZBAY, Bilkent University, Ankara, Turkey

J.G. PELLEGRINI, Night Vision and Electronic Sensors Directorate, Fort Belvoir, USA

M. RAZEGHI, Northwestern University, Evanston, USA

A. ROGALSKI, Military University of Technology, Warsaw, Poland

P. RUSSELL, Max Planck Institute for the Science of Light, Erlangen, Germany

V. RYZHII, University of Aizu, Aizu, Japan

C. SIBILIA, Universita' di Roma “La Sapienza”, Roma, Italy

A. TORRICELLI, Politecnico di Milano, Milano, Italy

T. WOLIŃSKI, Warsaw University of Technology, Warsaw, Poland

W. WOLIŃSKI, Warsaw University of Technology, Warsaw, Poland

S.−T. WU, University of Central Florida, Orlando, USA

Y.P. YAKOVLEV, Ioffe Physicotechnical Institute, St. Petersburg, Russia

J. ZIELŃSKI, Military University of Technology, Warsaw, Poland


Language Editor

J. Kulesza, e-mail: jolanta.kulesza@wat.edu.pl


Technical Editors:

R.Podraza, e-mail: renata.podraza@wat.edu.pl

E.Sadowska, e-mail: elzbieta.sadowska@wat.edu.pl

Kontakt

Military University of Technology,

Gen. Sylwestra Kaliskiego St. 2,

00 – 908 Warsaw, Poland

opelre@wat.edu.pl

Instrukcje dla autorów

Polityka Open Access

Opto-Electronics Review is an open access journal with all content available with no charge for readers in full text version. The journal content is available under the licencse CC BY-SA 4.0

Dodatkowe informacje

Opto-Electronics Review was established in 1992 for the publication of scientific papers concerning optoelectronics and photonics materials, system and signal processing. This journal covers the whole field of theory, experimental verification, techniques and instrumentation and brings together, within one journal, contributions from a wide range of disciplines. Papers covering novel topics extending the frontiers in optoelectronics and photonics are very encourage. The main goal of this magazine is promotion of papers presented by European scientific teams, especially those submitted by important team from Central and Eastern Europe. However, contributions from other parts of the world are by no means excluded.

Articles are published in OPELRE in the following categories:

-invited reviews presenting the current state of the knowledge,

-specialized topics at the forefront of optoelectronics and photonics and their applications,

-refereed research contributions reporting on original scientific or technological achievements,

-conference papers printed in normal issues as invited or contributed papers.

Authors of review papers are encouraged to write articles of relevance to a wide readership including both those established in this field of research and non-specialists working in related areas. Papers considered as “letters” are not published in OPELRE.

Opto-Electronics Review is published quarterly as a journal of the Association of Polish Electrical Engineers (SEP) and Polish Academy of Sciences (PAS) in cooperation with the Military University of Technology and under the auspices of the Polish Optoelectronics Committee of SEP.

Abstracting and Indexing:

Current Contents - Physical, Chemical & Earth Sciences

Current Contents - Engineering, Technology & Applied Sciences

Science Citation Index Expanded

Journal Citation Reports - Science Edition

Scopus

INSPEC

Policies and ethics:

The editors of the journal place particular emphasis on compliance with the following principles:

Authorship of the paper: Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the reported study.

Originality and plagiarism: The authors should ensure that they have written entirely original works, and if the authors have used the work and/or words of others, that this has been appropriately cited or quoted.

Data access and retention: Authors may be asked to provide the raw data in connection with a paper for editorial review, and should be prepared to provide public access to such data.

Multiple, redundant or concurrent publication: An author should not in general publish manuscripts describing essentially the same research in more than one journal or primary publication.

Acknowledgement of sources: Proper acknowledgment of the work of others must always be given.

Disclosure and conflicts of interest: All submissions must include disclosure of all relationships that could be viewed as presenting a potential conflict of interest.

Fundamental errors in published works: When an author discovers a significant error or inaccuracy in his/her own published work, it is the author's obligation to promptly notify the journal editor or publisher and cooperate with the editor to retract or correct the paper.

Reporting standards: Authors of reports of original research should present an accurate account of the work performed as well as an objective discussion of its significance.

Hazards and human or animal subjects: Statements of compliance are required if the work involves chemicals, procedures or equipment that have any unusual hazards inherent in their use, or if it involves the use of animal or human subjects.

Use of patient images or case details: Studies on patients or volunteers require ethics committee approval and informed consent, which should be documented in the paper.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji