In this paper, numerical results of modeling of acoustic waves propagation are presented. For calculation of the acoustic fluctuations, a solution of the full non-linear Euler equation is used. The Euler equations are solved with the use of a numerical scheme of third-order accuracy in space and time. The paper shows a validation process of the described method. This method is suitable also for an aerodynamic noise assessment on the basis of unsteady mean flow field data obtained from a CFD calculations. In such case this method is called a hybrid CFD/CAA method. The proposed method is numerically decoupled with CFD solution, therefore the information about the mean unsteady flow field can be obtained using an arbitrary CFD method (solver). The accuracy of the acoustic field assessment depends on the quality of the CFD solutions. This decomposition reduces considerably the computational cost in comparison with direct noise calculations.

The presented Euler acoustic postprocessor (EAP) has been used for modeling of the acoustic waves propagation in a cavity and in the flow field around a cylinder and an aerodynamic profile.

We propose a numerical surface integral method to study complex acoustic systems, for interior and exterior problems. The method is based on a parametric representation in terms of the arc’s lengths in curvilinear orthogonal coordinates. With this method, any geometry that involves quadric or higher order surfaces, irregular objects or even randomly rough surfaces can be considered. In order to validate the method, the modes in cubic, spherical and cylindrical cavities are calculated and compared to analytical results, which produced very good agreement. In addition, as examples, we calculated the scattering in the far field and the near field by an acoustic sphere and a cylindrical structure with a rough cross-section.

Periodic adsorption in a perfect mixing tank of a limited volume was considered. It was assumed that the adsorption rate is limited by diffusion resistance in a pellet. The approximate model of diffusion kinetics based on a continued fraction approximation was compared with the exact analytical solution. For the approximate model an algorithm was developed to determine a temporal variation of the adsorbate concentration in the pellet. The comparison was made for different values of the adsorbent load factor. In the numerical tests different shapes of pellets were considered. Both the numerical tests as well as our own experimental results showed that the approximate model provides results that are in good agreement with the exact solution. In the experimental part of this work adsorption of p-nitrophenol and acetic acid from aqueous solutions on cylindrical pellets of activated carbon was conducted.

The paper describes analytical approach solving the problem of dynamic analysis of two-dimensional fields of vibrational displacements and rotations caused by magnetic forces acting on stator of AC machine. Final set of three differential equations converted into algebraic ones is given and it is confronted with numerical solutions obtained by finite element method.

In the paper a novel mathematical model of electromechanical actuator is presented. It is based on application of Hamiltonian equations in the description of electro-mechanical energy conversion. It results in employment of flux linkages as state variables in the state space equations. For simplicity only a 3-phase wye connected stator winding without a neutral wire is considered in detail. The procedure can be generalised to any number of phases. Topology-based approach is used in the model implementation. Procedures for evaluation of all quantities (currents, energy/coenergy, electro-magnetic torque) present in model equations are described. Eddy currents and hysteresis phenolmenon are neglected in formulation of the model to enable application of state-space description.

The paper is devoted to the finding of the coefficient of one nonlinear wave equation in the mixed problem. The considered problem is reduced to the optimal control problem with proper functional. Differentiability of functional is proved and the necessary optimality conditions are derived in the form of the variational inequality. Existence of the optimal control is proved.

The nonlinear interaction of wave and non-wave modes in a gas planar flow are considered. Attention is mainly paid to the case when one sound mode is dominant and excites the counter-propagating sound mode and the entropy mode. The modes are determined by links between perturbations of pressure, density, and fluid velocity. This definition follows from the linear conservation equations in the differential form and thermodynamic equations of state. The leading order system of coupling equations for interacting modes is derived. It consists of diffusion inhomogeneous equations. The main aim of this study is to identify the principle features of the interaction and to establish individual contributions of attenuation (mechanical and thermal attenuation) in the solution to the system.

The sound speed and parameters of nonlinearity B/A, C/A in a fluid are expressed in terms of coefficients in the Taylor series expansion of an excess internal energy, in powers of excess pressure and density. That allows to conclude about features of the sound propagation in fluids, the internal energy of which is known as a function of pressure and density. The sound speed and parameters of nonlinearity in the mixture consisting of boiling water and its vapor under different temperatures, are evaluated as functions of mass concentration of the vapor. The relations analogous to that in the Riemann wave in an ideal gas are obtained in a fluid obeying an arbitrary equation of state. An example concerns the van der Waals gases. An excess pressure in the reflected wave, which appears when standard or nonlinear absorption in a fluid takes place, is evaluated in an arbitrary fluid.

The majority of publications and monographs present investigations which concern exclusively twophase flows and particulary dispersed flows. However, in the chemical and petrochemical industries as well as in refineries or bioengineering, besides the apparatuses of two-phase flows there is an extremely broad region of three-phase systems, where the third phase constitutes the catalyst in form of solid particles (Duduković et al., 2002; Martinez et al., 1999) in either fixed bed or slurry reactors. Therefore, the goal of this study is to develop macroscopic, averaged balances of mass, momentum and energy for systems with three-phase flow. Local instantaneous conservation equations are derived, which constitute the basis of the method applied, and are averaged by means of Euler’s volumetric averaging procedure. In order to obtain the final balance equations which define the averaged variables of the system, the weighted averaging connected with Reynolds decomposition is used. The derived conservation equations of the trickle-bed reactor (mass, momentum and energy balance) and especially the interphase effects appearing in these equations are discussed in detail.

In the paper a novel mathematical model of electromechanical actuator is presented. It is based on application of Hamiltonian equations in the description of electromechanical energy conversion. It results in employment of flux linkages as state variables in the state space equations. For simplicity only a 3-phase wye connected stator winding without a neutral wire is considered in detail. The procedure can be generalised to any number of phases. Topology-based approach is used in the model implementation. Procedures for evaluation of all quantities (currents, energy/coenergy, electromagnetic torque) present in model equations are described. Eddy currents and hysteresis phenolmenon are neglected in formulation of the model to enable application of state-space description.

Commonly, the Park model is used to calculate transients or steady-state operations of synchronous machines. The expanded Park theory derives the Park equations from the phase-domain model of the synchronous machine by the use of transformations. Thereby, several hypothesis are made, which are under investigation in this article in respect to the main inductances of two different types of synchronous machines. It is shown, that the derivation of the Park equations from the phase-domain model does not lead to constant inductances, as it is usually assumed for these equations. Nevertheless the Park model is the most common analytic model of synchronous machines. Therefore, in the second part of this article a method using the evolution strategy is shown to obtain the parameters of the Park model.

In this paper, Lagrange’s equations along with the Ritz method are used to obtain the equation of motion for a flexible, slender cylinder subjected to axial flow. The cylinder is supported only by a translational and a rotational spring at the upstream end, and at the free end, it is terminated by a tapering end-piece. The equation of motion is solved numerically for a system in which the translational spring is infinitely stiff, thus acting as a pin, while the stiffness of the rotational spring is generally non-zero. The dynamics of such a system with the rotational spring of an average stiffness is described briefly. Moreover, the effects of the length of the cylinder and the shape of the end-piece on the critical flow velocities and the modal shapes of the unstable modes are investigated.

The considerations presented in this paper include a computer analysis of slide bearing wear prognosis using the solutions of recurrence equations complemented with the experimental data values. On the ground of the results obtained from analytical and computational numerical calculations, and taking into account the experimental parameters of bearing material and operation boundary conditions, the control problems of slide bearing wear surfaces have been presented. The obtained results allow us to see a connection between roughness, material properties, the amplitude of vibrations, the kind of the friction forces, the hardness of materials, the sliding speed in one side and the wear increments in succeeding time units of the exploitation process in other side.

The effects of friction were observed in electric guitar strings passing over an electric guitar saddle. The effects of changing the ratio of the diameter of the winding to the diameter of the core of the string, the angle through which the string is bent, and the length on either side of the saddle were measured. Relative tensions were deduced by plucking and measuring the frequencies of vibration of the two portions of string. Coefficients of friction consistent with the capstan equation were calculated and were found to be lower than 0.26 for wound strings (nickel plated steel windings on steel cores) and lower than 0.17 for unwound (tin plated steel) strings. The largest values of friction were associated with strings of narrower windings and wider cores and this may be due to the uneven nature of the contact between the string and saddle for wound strings or due the surface of the windings deforming more, encouraging fresh (and therefore higher friction) metal to metal contact. It is advised to apply lubrication under the saddle to string contact point after first bringing the string up to pitch rather than before in order to prevent this fresh metal to metal contact.

In the paper, maximal values xe(τ) of the solutions x(t) of the linear differential equations excited by the Dirac delta function are determined. There are obtained the analytical solutions of the equations and also the maximal positive values of these solutions. The obtained sufficient conditions of the positivity of these solutions are defined by the Theorems. There are also formulated the necessary conditions of the positivity of these solutions. The analytical formulae enable the design of the system with prescribed properties [3].