This paper presents the method of analysis of parametric systems in frequency domain. These systems are also referred to as linear time varying systems (LTV). The article includes a description of an analytical method for determining the frequency response of the first order parametric circuit with non-periodically variable parameters. The results have been illustrated by an example.
The article proposes the method of synthesis of active elements with time-varying parameters R(t), C(t) and L(t). In order to construct the elements, it is necessary to use operational amplifiers, multipliers and classic RLC components. The variability in time of the elements results from applying voltage to control terminals. Assuming that the parameters of elements R(t), L(t), C(t) are exponentially varying, dependencies describing the control voltage waveforms which enable such a parameter variability were determined. The obtained results were illustrated with examples and PSpice simulations.
The paper presents results of numerical calculations and experimental data on the directional pattern of two 38-element parametric arrays composed of ultrasound sources. Two types of antenna arrays are considered, namely with parallel and coaxial connections of ultrasonic transducers (elements). The results of selecting and functional testing of unit elements are described in this paper. It is found that in the coaxial element connection of the antenna array, the level of side lobes is higher than that in the parallel element connection.
One of the problems in Russia Power Sector strategy until 2035 is the technologies development for mitigation of harmful emissions by the heat and power production industry. This goal may be reached by the transition to environmentally friendly generation units such as oxy-fuel combustion power cycles that burn organic fuels in pure oxygen. This paper provides the results of research on one of the most efficient oxy-fuel combustion power cycle, which was modified by the usage of nitrogen for turbine cooling. The computer simulation and parametric optimization approaches are described in detail. The net efficiency of the oxy-fuel combustion power cycle in relationship to the carbon dioxide turbine exhaust pressure is shown. Moreover, the influence of the regenerator scheme and modeling parameters on heat performance is obtained. Particularly, it was found that the transition to a scheme with five two-threaded heat exchangers decrease cycle efficiency by 4.2% compare to a scheme with a multi-stream regenerator.
We demonstrate MW-level, single resonance optical parametric oscillator, based on KTP Type-II crystal with noncritical phase-matching. The OPO is pumped by electro-optically Q-switched Nd:YAG slab laser providing 55 mJ of pulse energy. At the output, we achieved 28 mJ of signal pulse energy at 1.57 μm with 51% conversion efficiency, corresponding to 1.4 MW of peak power.
This paper proposes a design procedure for observer-based controllers of discrete-time switched systems, in the presence of state’s time-delay, nonlinear terms, arbitrary switching signals, and affine parametric uncertainties. The proposed switched observer and the state- feedback controller are designed simultaneously using a set of linear matrix inequalities (LMIs). The stability analysis is performed based on an appropriate Lyapunov–Krasovskii functional with one switched expression, and in the meantime, the sufficient conditions for observer-based stabilization are developed. These conditions are formulated in the form of a feasibility test of a proposed bilinear matrix inequality (BMI) which is a non-convex problem. To make the problem easy to solve, the BMI is transformed into a set of LMIs using the singular value decomposition of output matrices. An important advantage of the proposed method is that the established sufficient conditions depend only on the upper bound of uncertain parameters. Furthermore, in the proposed method, an admissible upper bound for unknown nonlinear terms of the switched system may be calculated using a simple search algorithm. Finally, the efficiency of the proposed controller and the validity of the theoretical results are illustrated through a simulation example.
The industrial grinding devices, which work in the high-energetic fluidized bed conditions make it possible to obtain guaranteed particle size distribution of product and decrease of consumption energy. The matrix model for transformation of particle size distribution in the fluidized bed opposed jet mill is presented in the part IV of article. The proposed model contains the mass population balance of particle equation, in which are block matrices: the matrix of circuit M, the matrix of inputs F and the matrix of feed F0. The matrix M contains blocks with the transition matrix P, the classification matrix C, the identity matrix I and the zero matrix 0. The matrix was marked using with discrete forms of the selection and breakage functions, mean while the matrices of classification - using the equation, describing classification of grains in the grinding chamber of mill. In paper was discussed this model in details (part 2.1). The correctness of received form of the selection and breakage functions was confirmed. The method determination of the transition matrix for fluidized-jet grinding of grains (part 2.2) and the classification matrix for gravitational and centrifugal zones of grains (part 2.3) are presented. The verification of model obtained on basis results with experimental investigations, which were performed on a laboratory fluidized bed opposed jet mill. The experiment contained grinding of selected narrow size fractions of limestone in turbulent fluidized layer conditions, what in part I and part II of article (Zbroński, Górecka-Zbrońska 2007a, b) are presented. The parameters of parametric identification were: factor of proportionality - contained in the equation on the discrete form of selection function and sizes of limiting grains - contained in equation on the diagonal elements of classification matrix for stage of gravitational and centrifugal (part 3). The classic Fisher-Snedecor test was applied for estimation of prediction particle size distribution of grinding product (part 4). The significant divergences between numerical and experimental results of particle size distribution weren't affirmed. The experimental verification, parametric identification and statistical estimation of the proposed model showed that this model make it possible to forecasting particle size distribution of grinding product.
The article discusses the issues of accounting the direction pattern of parametric antenna array the propagation of sound over the Earth’s surface. As a radiator, a parametric antenna array is used. A description is given of measuring equipment and experimental research methods. The Delaney-Bezley model was used as a model of the Earth’s surface impedance. The research results showed the importance of accounting the direction pattern of parametric antenna array in predicting the sound pressure level of a propagating acoustic signal over the Earth’s surface. On the example of a difference signal with a frequency of 2 kHz, the calculation of the sound pressure level on a 100-meter path with the influence of the Earth’s surface is shown. The results obtained showed a good agreement between the theoretical calculation and experimental data.
A navigation complex of an unmanned flight vehicle of small class is considered. Increasing the accuracy of navigation definitions is done with the help of a nonlinear Kalman filter in the implementation of the algorithm on board an aircraft in the face of severe limitations on the performance of the special calculator. The accuracy of the assessment depends on the available reliable information on the model of the process under study, which has a high degree of uncertainty. To carry out high-precision correction of the navigation complex, an adaptive non-linear Kalman filter with parametric identification was developed. The model of errors of the inertial navigation system is considered in the navigation complex, which is used in the algorithmic support. The procedure for identifying the parameters of a non-linear model represented by the SDC method in a scalar form is used. The developed adaptive non-linear Kalman filter is compact and easy to implement on board an aircraft.
The paper considers parametric optimization problems for the steel bar structures formulated as nonlinear programming ones with variable unknown cross-sectional sizes of the structural members, as well as initial prestressing forces introduced into the specified redundant members of the structure. The system of constraints covers load-bearing capacity constraints for all the design sections of the structural members subjected to all the design load combinations at ultimate limit state, as well as displacement constraints for the specified nodes of the bar system, subjected to all design load combinations at serviceability limit state. The method of the objective function gradient projection onto the active constraints surface with simultaneous correction of the constraints violations has been used to solve the parametric optimization problem. A numerical technique to determine the optimal number of the redundant members to introduce the initial prestressing forces has been offered for high-order statically indeterminate bar structures. It reduces the dimension for the design variable vector of unknown initial prestressing forces for considered optimization problems.
The aim of the study was to develop a practical approach to parametric shaping of spatial steel rod structures formed based on a hyperbolic paraboloid. This design approach was realized by application of designing tools working in environment of Rhinoceros 3D, that is its plug-in Grasshopper for geometric modelling and Karamba 3D for structural analysis. The goal of this research was to elaborate an universal scripts in order to create rod structures‘ models of various forms and grid patterns, as well as evaluating their structural behaviour dependently on various boundary conditions. The optimisation criterion was the minimum mass and deflection. Several proposals of coverings by means of single layer grid structures were presented and analysed to choose the best solution. The rod structures generated based on a hyperbolic paraboloid turned out to be structures with good static properties, so may be an interesting proposals to cover large areas.
The paper deals with the digital architecture concept which is trying to introduce a new spatial language into the con-text of water urbanism, using nature as a model, measure and mentor. The first part analyses Biomimetics with its design strategies and methods. The Problem-Based Approach (designers look to nature for solutions) and the Solution-Based Ap-proach (biological knowledge influences human design) are defined here. In the second part of the research, the authors present selected examples to the topic. This case study has demonstrated that a new approach to architectural design is emerging. This approach redefines the process of architectural design, understood not as the traditional shaping of the ob-ject's form, but as a compilation of various factors resulting from changeable climate characteristics and ecology. The con-clusions emphasize that not only the contemporary understanding of ecology should be changed, but also the way architects approach the built environment, especially in the aquatic environment.