Based on laboratory tests of selected properties of secondary waste (ashes and dusts) from municipal waste incineration plants, the possibility of recovering some properties of waste in the process of filling the post-mining voids in the salt mine was assessed. The furnace bottom ash and the waste from the flue gas treatment from one of the national incineration plants were examined. The grain curves of dry waste and the density of the prepared mixtures were characterized. Twelve variants of the compositions of ash-based mixtures with varying proportions of the individual components were considered, taking into account both fresh water and brine. For each variant of the composition, the amount of redundant liquid appeared as well as the time of solidifying of the mixture to a certain strength and the compressibility values obtained. Considering the possibility of transporting mixtures in mines by means of pipelines at relatively long distances, and allowing the filling of large salt chambers to be filled and evenly filled, flow parameters were determined. In addition, the permeability of solidified waste samples was investigated, showing the potential for reducing the strength of the waste mass due to the action of water or brine. The technical feasibility of eliminating redundant liquid in the binding process has been confirmed, which is particularly important in salt mines. Preliminary values for the amount of binder (5%÷10%) to be added to the mixtures to obtain the specified strength properties of the artificially formed mass at Rc = 0.5 MPa. Attention was paid to the important practical aspect resulting from the rapid increase of this type of waste in the comming years in Poland and at the same time vast potential for their use in salt mining, where we have a huge capacity of salt chambers available.
The ablation casting technology consists in pouring castings in single-use moulds made from the mixture of sand and water-soluble binder. After pouring the mould with liquid metal the mould is destructed (washed out) using a stream of cooling medium, which in this case is water. The process takes place while the casting is still solidifying.
The following paper focuses on testing the influence of the modified ablation casting of aluminum alloy on casts properties produced in moulds with hydrated sodium silicate binder. The authors showed that the best kind of moulding sands for Al alloy casting will be those hardened with physical factors – through dehydration. The analysis of literature data and own research have shown that the moulding sand with hydrated sodium silicate hardened by dehydration is characterized by sufficient strength properties for the modified ablation casting of Al alloys. In the paper the use of microwave hardened moulding sands has been proposed.
The moulds were prepared in the matrix specially designed for this technology. Two castings from the AlSi7Mg alloy were made; one by traditional gravity casting and the other by gravity casting using ablation.
The conducted casts tests showed that the casting made in modified ablation casting technology characterizes by higher mechanical properties than the casting made in traditional casting technology. In both experimental castings the directional solidification was observed, however in casting made by ablation casting, dimensions of dendrites in the structure at appropriate levels were smaller.
A hot compression test was conducted on a Gleeble-3500 thermo-simulation machine to study the critical conditions and kinetics of dynamic recrystallization in a high-carbon tool steel. The critical conditions for the initiation of dynamic recrystallization were determined using the working-hardening theory. The quantitative relationship between the critical characteristics of dynamic recrystallization and the hot deformation parameters were elucidated based on two different methods:the apparent method and physically based method. It was found that the two methods both have high applicability for the investigated steel, but the physically-based method needs less parameters and makes it possible to study the effect of different factors. A dynamic recrystallization kinetics model was used to calculate the recrystallization volume fraction under different conditions. The calculation results matched well with the data obtained from the flow curves.
Increasing demands are imposed on foundries to enforce the manufacture of castings characterized by tight dimensional tolerances, high surface finish and total absence of casting defects. To face these challenges, castings are increasingly made in loose self-hardening sands with furfuryl resin, commonly known as furan sands. In the group of self-hardening sands with synthetic resins, loose self-hardening sands with furfuryl resin enjoy the greatest popularity. The sand mixtures based on furan resins are usually subjected to mechanical reclamation. The consumption of binder and hardener and thus the cost of the sand depend on the quality of reclaim, and mainly on the dust removal degree.
The planned tightening of the environmental protection regulations in the EU countries, including limiting the content of free furfuryl alcohol in resins and reducing the emission of furfuryl alcohol, formaldehyde and BTEX compounds at workplaces, necessitated the development of a new generation of eco-friendly furfuryl resins that have recently appeared on the market.
The main aim of this article was to determine the effect of reclaim content on the sand parameters, such as bending strength, tensile strength, bench life, gas-forming tendency and loss on ignition. Tests were carried out with reclaim content in the sand mixture varying from 50 to 90%. The reclaim obtained by dry mechanical reclamation was supplied by one of the domestic foundries.
The results showed that the highest mechanical properties were obtained in sands containing 60% of the reclaim.