The practice capacity of a railway junction depends, in addition to the effective operation’s conditions, by the potential risk factors related to the design plan of the railway station. With the aim of an approach based on the “fuzzy sets” it is possible to determine the numeric value of the practice capacity by the logic – qualitative relations between the features of the railway junction and the potential risk factors. This methodology permits to try out the absolute value of a suitable vector β, (less then the unit) for the utilization of the theoretic capacity in conditions of maximum reliability of the system related to the aspect of safety (technique “fail safe”).
The Dez dam was commissioned in 1963 and since sediments accumulated in the reservoir up to an elevation of approximately 15m below the intake of the power tunnel. One of the possible measures to improve operation of the reservoir is by heightening of the existing dam. This paper describes the conducted procedure for static and thermal calibration of this 203m dam in Iran based on micro geodesies measurements. Also the nonlinear response of existing dam is investigated under maximum credible earthquake ground motions considering joint behavior and mass concrete cracking and safety of dam is evaluated for possible heightening. For thermal calibration of provided numerical model, transient thermal analysis was conducted and results were compared with thermometers records installed in central block. In addition, for static calibration; thermal distribution within dam body, dam self weight, hydrostatic pressure and silt load applied on the 3D fi nite element model of dam-reservoir-foundation were considered. Results show that the distribution of stresses will be critical within dam for heightening case under seismic loads in MCL.
Wind constitutes one of the major environmental factors affecting the design and performance of built environment. Each country has its unique climatic wind conditions, and the way in which these are considered and implemented in the structural design, is important. An implementation or adoption of any new engineering design stipulations introduces a formidable challenge to the developers of the standards and the design profession. This has been experienced in some of the countries (e.g. the UK, Australia and the USA), where processes of modernising the outdated codifi cation took place in the past. Although both Poland and South Africa are currently at the early implementation stage of the new wind loading design stipulations, there is a major difference between the circumstances of the two countries. Poland, as an EU member state, has a compulsory obligation to adopt the new uniform standarisation requirements, within a stipulated time-frame. The South African code developers, after a thorough investigation process which will be highlighted in the paper, decided voluntarily to adopt the Eurocode as the primary model document.
The volume changes caused by coupled temperature and moisture variations in early-age concrete elements lead to formation of stresses. If a restraint exists along the contact surface of mature concrete against which a new concrete element has been cast, generated stresses are mostly of a restraint origin. In engineering practice a wide range of externally restrained concrete elements can be distinguished such as tank walls or bridge abutments cast against an old set foundation, in which early-age cracking may endanger their durability or functionality. Therefore, for years methods were being developed to predict early-age stresses and cracking risk of externally restrained concrete elements subjected to early-age thermal-moisture effects. The paper presents the comparative study of the most recognised analytical approaches: the method proposed in EC2, the method proposed by ACI Committee 207 and the method developed at the Luleå University of Technology.
Reliable estimation of geotechnical parameters is often based on reconstruction of a complete loading process of subsoil on a specimen in laboratory tests. Unfortunately laboratory equipment available in many laboratories is sometimes limited to just a triaxial apparatus
– the use of which generates diffi culties whenever a non-axisymmetric problem is analysed.
The author suggests two simple operations that may be done to improve the quality of simulation in triaxial tests. The fi rst one is based on the use of triaxial extension along the segments of the stress path p’-q-θ for which the Lode’s angle values are positive. The second one consists in a mod-ifi cation of the equivalent stress value in such a way that the current stress level in the specimen complies with results of FEM analysis.
The paper provides a solution to the problem of dimensioning decisive bars on the basis of the conditions of meeting the recommended reliability classes  of statically determinate structures composed of n members. A theorem was formulated:if a statically determinate structure composed of n decisive members is to attain the reliability greater than, or equal to, the recommended relia-bility p = 1 – q, it is necessary and suffi cient that the damage frequency sum qᵢ of decisive members is smaller than the admissible damage frequency q of thestructure: ∑qᵢ < q. On the basis of this theorem, s coeffi cients that recommend increase of the load bearing capacity of the decisive bars in a statically determinate structure constructed in order to meet the recommended class  of the structure reliability, are estimated and presented in a tabular form.
Each bitumen has a slightly different group composition, thus bitumen modifi cation with the SBS copolymer gives slightly different results in each case. Both in the industry and construction prac-tice there is still no simple method available which would allow the evaluation of the impact of SBS content and the group composition of bitumen on the structural and rheological properties of the polymer bitumen mix. The article presents the results of the dynamic viscosity tests of three bitumen types. Based on the analysis of the results obtained, it was found that changes in the rheological properties caused by SBS additive are characteristic for each of the bitumens tested and their chemical and group composition. They are also proportionate to the amount of the modifi er added. In order to have a possibility to measure this impact, three coeffi cients rheologically charac-terizing polymer and bitumen mixes were applied.
Submission of articles for publication in the journal Archives of Civil Engineering should be made via the website:
Aby subskrybować czasopismo wpisz swój adres e-mail:
*Pola oznaczone gwiazdką są obowiązkowe do wypełnienia i zaznaczenia. Aby subskrybować czasopismo musisz wyrazić zgodę na przetwarzanie danych osobowych.