Nauki Techniczne

Opto-Electronics Review

Zawartość

Opto-Electronics Review | 2018 | vol. 26 | No 1

Abstrakt

Transparent Al doped ZnO nanocrystalline films with a crystallite size less than 19 nm are obtained by spray pyrolysis. Band gap increases monotonically from 3.16 to 3.31 eV with increasing aluminum dopant up to 1.56 at.% facilitating increasing width of a transmission window in addition to the band gap tuning of 4.74% which compares favorably well with literature. UV emission with continuously increasing intensity is obtained which reflects on the good crystalline quality of the films. Also the defect emissions are suppressed remarkably as the dopant Al concentration increases in ZnO. The band gap tuning by quite small increment in dopant amount makes the present films, much attractive for the fabrication of light emitting devices with a much sought-for benefit of large area fabrication. FESEM shows the surface is granular with grain size lying in the range of 20–35 nm and EDX confirms the presence of Al in the doped samples.

Przejdź do artykułu

Autorzy i Afiliacje

N. Kumar
A. Srivastava

Abstrakt

In the present work TiO2 nanoparticles (NPs) have been dispersed into three different nematic liquid crystals (2020, 1823A and 1550C) in different concentration. The value of the birefringence (Δn) has been calculated by the transmitted intensity method at a 632.8 nm wavelength. NLC 2020 used in the present study is a high birefringent material (Δn = 0.44), NLC 1550C is a low birefringent material (Δn = 0.067) and NLC 1823A is a mid birefringent material (Δn = 0.14). An increased value of birefringence has been found after dispersion of TiO2 NPs in all three NLCs but this increment depends upon the concentration of the dopant material, temperature range and chemical character of the mixtures. It is suggested that this LC materials can be applicable in making of phase shifters, compensators and many more photonic devices.

Przejdź do artykułu

Autorzy i Afiliacje

G. Pathak
R. Katiyar
K. Agrahari
A. Srivastava
R. Dabrowski
K. Garbat
R. Manohar

Abstrakt

Photofield emission from SiGe nanoislands formed by molecular beam epitaxy (MBE) have been investigated. Two types of nanoislands, namely the domes and pyramids with different heights, have been addressed. It was found that the arrays of SiGe nanoislands exhibited a low onset voltage for field emission. The increase of emission current and the decrease of the curve slope in Fowler-Nordheim coordinates under green light illumination have been revealed. Electron field emission and photoemission from SiGe nanoislands have been explained based on the energy band diagram of Si-Ge heterostructure and some energy barriers have been determined.

Przejdź do artykułu

Autorzy i Afiliacje

O. Steblova
A. Evtukh
O. Yilmazoglu
V. Yukhymchuk
H. Hartnagel
H. Mimura

Abstrakt

An interferometric structure based on a Dual-Resonance Long-Period Grating (DRLPG) within a Fiber Loop Mirror (FLM) is presented in this paper. Its purpose is to measure the refractive index (RI) of liquid analytes. The grating is the RI sensing probe, while the FLM serves as a band-pass filter. Due to the high extinction ratio of the FLM, amplitude measurements can be obtained, allowing implementation of the differential interrogation method to establish the sensitivity of the device. The use of a polarization controller makes it possible to fine-tune the interferometric peaks with respect to the two notches of the DRLPG. Precisely aligned configuration produces a maximum sensitivity of 3871.5 dB/RIU within the RI range of 1.3333 up to 1.3419 with linear sensor response.

Przejdź do artykułu

Autorzy i Afiliacje

R. Zawisza
T. Eftimov
P. Mikulic
Y. Chinifooroshan
A. Celebańska
W.J. Bock
L.R. Jaroszewicz
ORCID: ORCID

Abstrakt

Self-swept erbium fiber laser emitting around 1.56 μm is reported in detail. Both sweep directions were registered: pointing toward longer and shorter wavelengths, redshift and blueshift sweeping, respectively. We describe method of determining the direction of the wavelength drift using the monochromator based optical spectrum analyzer. Possible root for this sweeping regime, i.e., the gain modulation along active fiber, is discussed with the help of a simple model calculating the overall cavity gain that can predict the direction of the laser wavelength sweeping.

Przejdź do artykułu

Autorzy i Afiliacje

P. Navratil
Pavel Peterka
ORCID: ORCID
P. Vojtisek
I. Kasik
J. Aubrecht
P. Honzatko
V. Kubecek

Abstrakt

We have presented dielectric and conductivity studies of two liquid crystal (LC) compounds- p-octyloxybenzoic acid (8OBA) and p-decyloxybenzoic acid (10OBA). Dielectric permittivity study of those compounds gives the evidence of space charge polarization and ionic conductance in the samples. Dielectric permittivity is found to be the highest for 8OBA than 10OBA. Both compounds found to exhibit positive dielectric anisotropy. Splay elastic constant as a function of temperature has also been investigated. Frequency and temperature dependent electrical conductivity of these two LC compounds have been studied in detail. Activation energy has been estimated from both dc and ac conduction process.

Przejdź do artykułu

Autorzy i Afiliacje

S. Patari
A. Nath

Abstrakt

Dielectric properties of a nematic liquid crystal (NLC) mixture ZhK-1282 were investigated in the frequency range of 102–106 Hz and a temperature range of −20 to 80°С. On the basis of the Debye’s relaxation polarization model dielectric spectra of temperature dependence of the orientational relaxation time τ and the dielectric strength δe were numerically approximated at the parallel orientation of a molecular director relative to alternating electric field. Influence of ester components in the mixture plays crucial role in relaxation processes at low temperature and external field frequency. The activation energy of the relaxation process of a rotation of molecules around their short axis was measured in a temperature interval of −20 to  +15°С in which the dispersion of a longitudinal component of the dielectric constant takes place. The energy of potential barrier for polar molecules rotation in the mesophase was calculated. The value of the transition entropy from the nematic to isotropic phase was obtained from this calculation. The values of the coefficient of molecular friction and rotational diffusion were obtained by different methods. The experimental data obtained are in a satisfactory agreement with the existing theoretical models.

Przejdź do artykułu

Autorzy i Afiliacje

D.N. Chausov
А.D. Kurilov
V.V. Belyaev
S. Kumar

Abstrakt

A highly sensitive photonic crystal fiber based on the surface plasmon resonance (PCF-SPR) biosensor for the detection of the density alteration in non-physiological cells (DANCE) is described. Human acute leukemia cells are determined by the discontinuous sucrose gradient centrifugation (DSGC) in which the cells are separated into several bands. The separated cells with different intracellular densities and refractive indexes (RI) ranging from 1.3342 to 1.3344 are distinguished in situ by means of the differential transmission spectrum. The biosensor shows a maximum amplitude sensitivity of 2000 nm/RIU and resolution as high as 5 × 10−5 RIU. According to the wavelength interrogation method, a maximum spectral sensitivity of 9000 nm/RIU in the sensing range between 1.33 and 1.53 is achieved, corresponding to a resolution as high as 1.11 × 10−5 RIU for the biosensor. The proposed PCF-SPR biosensor has promising application in biological and biochemical detection.

Przejdź do artykułu

Autorzy i Afiliacje

F. Wang
Z. Sun
C. Liu
T. Sun
P.K. Chu

Abstrakt

We have numerically studied different designs of technologically feasible microstructured fibers with a germanium-doped core in order to obtain normal dispersion reaching possibly far in the mid infrared. Hexagonal, Kagome and the combination of both geometries were numerically examined with respect to different constructional parameters like pitch distance, filling factor of air holes, number of layers surrounding the core, and level of germanium doping in the core. Our analysis showed that the broadest range of normal dispersion reaching 2.81 μm, while keeping an effective mode area smaller than 30 μm2, was achieved for a hexagonal lattice and a 40 mol% GeO2 doped core. The proposed fibers designs can be used in generation of a normal dispersion supercontinuum reaching the mid-IR region.

Przejdź do artykułu

Autorzy i Afiliacje

J. Biedrzycki
K. Tarnowski
W. Urbańczyk

Abstrakt

In this article, we propose the realization of XNOR logic function by using all-optical XOR and NOT logic gates. Initially, both XOR and NOT gates are designed, simulated and optimized for high contrast outputs. T-shaped waveguides are created on the photonic crystal platform to realize these logic gates. An extra input is used to perform the inversion operation in the NOT gate. Inputs in both the gates are applied with out of phase so as to have a destructive interference between them and produce negligible intensity for logic ‘0'. The XOR and NOT gates are simulated using Finite Difference Time Domain method which results with a high contrast ratio of 55.23 dB and 54.83 dB, respectively at a response time of 0.136 ps and 0.1256 ps. Later, both the gates are cascaded by superimposing the output branch of the waveguide of XOR gate with the input branch of the waveguide of NOT gate so that it can be resulted with compact size for XNOR logic function. The resultant structure of XNOR logic came out with the contrast ratio of 12.27 dB at a response time of 0.1588 ps. Finally, it can be concluded that the proposed structures with fair output performance can suitably be applied in the design of photonic integrated circuits for high speed computing and telecommunication systems.

Przejdź do artykułu

Autorzy i Afiliacje

E.H. Shaik
N. Rangaswamy

Abstrakt

Properties of excitons confined to potential fluctuations due to indium distribution in the wetting layer which accompany self-assembled InAs/GaAs quantum dots are reviewed. Spectroscopic studies are summarized including time-resolved photoluminescence and corresponding single-photon emission correlation measurements. The identification of charge states of excitons is presented which is based on results of a theoretical analysis of interactions between the involved carriers. The effect of the dots’ environment on their optical spectra is also shown.

Przejdź do artykułu

Autorzy i Afiliacje

A. Babiński

Instrukcja dla autorów

Guide for Authors

https://www.editorialsystem.com/opelre/journal/for_authors/

OPTO-ELECTRONICS REVIEW is an open access journal. This involves the payment of an article publishing charge (APC) by the authors, their institution or funding body. We make the article freely available immediately upon publication on PAS Jornals platform (https://journals.pan.pl/opelre)

As of July 1st, 2024, there are changes in the fees for open access publications in Opto-Electronics Review: 2000 PLN (500 EUR) - up to 8 pages of the journal format and mandatory over-length charges of 200 PLN (50 EUR) per page (see the above link with instructions for Authors for details)

Articles submitted by June 30th, 2024: existing fee: 1750 PLN (or 400 EUR)

Articles submitted from July 1st, 2024: new fee: 2000 PLN (or 500 EUR) - a flat fee per paper up to 8 pages of the journal format (each additional page will be charged an additional 200 PLN or 50 EUR).

Dodatkowe informacje

Opto-Electronics Review was established in 1992 for the publication of scientific papers concerning optoelectronics and photonics materials, system and signal processing. This journal covers the whole field of theory, experimental verification, techniques and instrumentation and brings together, within one journal, contributions from a wide range of disciplines. Papers covering novel topics extending the frontiers in optoelectronics and photonics are very encouraged. The main goal of this magazine is promotion of papers presented by European scientific teams, especially those submitted by important team from Central and Eastern Europe. However, contributions from other parts of the world are by no means excluded.

Articles are published in OPELRE in the following categories:

-invited reviews presenting the current state of the knowledge,

-specialized topics at the forefront of optoelectronics and photonics and their applications,

-refereed research contributions reporting on original scientific or technological achievements,

-conference papers printed in normal issues as invited or contributed papers.

Authors of review papers are encouraged to write articles of relevance to a wide readership including both those established in this field of research and non-specialists working in related areas. Papers considered as “letters” are not published in OPELRE.

Opto-Electronics Review is published quarterly as a journal of the Association of Polish Electrical Engineers (SEP) and Polish Academy of Sciences (PAS) in cooperation with the Military University of Technology and under the auspices of the Polish Optoelectronics Committee of SEP.

Abstracting and Indexing:

Arianta

BazTech

EBSCO relevant databases

EBSCO Discovery Service

SCOPUS relevant databases

ProQuest relevant databases

Clarivate Analytics relevant databases

WangFang

additionally:

ProQuesta (Ex Libris, Ulrich, Summon)

Google Scholar

Policies and ethics:

The editors of the journal place particular emphasis on compliance with the following principles:

Ethical policy of Opto-Electronics Review

The ethical policy of Opto-Electronics Review follows the European Code of Conduct for Research Integrity and is also guided by the core practices and policies outlined by the Committee on Publication Ethics (COPE).

Authors must be honest in presenting their results and conclusions of their research. Research misconduct is harmful for knowledge.

Research results

Fabrication, falsification, or selective reporting of data with the intent to mislead or deceive is unethical, as is the theft of data or research results from others. The results of research should be recorded and maintained to allow for analysis and review. Following publication, the data should be retained for a reasonable period and made available upon request. Exceptions may be appropriate in certain circumstances to preserve privacy, to assure patent protection, or for similar reasons.

Authorship

All those who have made a significant contribution should be given chance to be cited as authors. Other individuals who have contributed to the work should be acknowledged. Articles should include a full list of the current institutional affiliations of all authors, both academic and corporate.

Competing interests

All authors, referees and editors must declare any conflicting or competing interests relating to a given article. Competing interests through their potential influence on behavior or content or perception may undermine the objectivity, integrity, or perceived value of publication.

Peer Review

We are committed to prompt evaluation and publication of fully accepted papers in Opto-Electronics Review’s publications. To maintain a high-quality publication, all submissions undergo a rigorous review process.

Characteristics of the peer review process are as follows:

• Simultaneous submissions of the same manuscript to different journals will not be tolerated.

• Manuscripts with contents outside the scope will not be considered for review.

• Opto-Electronics Review is a single-blind review journal.

• Papers will be refereed by at least 2 experts as suggested by the editorial board.

• In addition, Editors will have the option of seeking additional reviews when needed. Authors will be informed when Editors decide further review is required.

• All publication decisions are made by the journal’s Editor-in-Chief based on the referees’ reports. Authors of papers that are not accepted are notified promptly.

• All submitted manuscripts are treated as confidential documents. We expect reviewers to treat manuscripts as confidential material.

• Editors and reviewers involved in the review process should disclose conflicts of interest resulting from direct competitive, collaborative, or other relationships with any of the authors, and remove oneself from cases in which such conflicts preclude an objective evaluation. Privileged information or ideas that are obtained through peer review must not be used for competitive gain.

• A reviewer should be alert to potential ethical issues in the paper and should bring these to the attention of the editor, including any substantial similarity or overlap between the manuscript under consideration and any other published paper of which the reviewer has personal knowledge. Any statement, observation, derivation, or argument that had been previously reported should be accompanied by the relevant citation.

• Personal criticism is inappropriate.

Plagiarism

Reproducing text from other papers without properly crediting the source (plagiarism) or producing many papers with almost the same content by the same authors (self-plagiarism) is not acceptable. Submitting the same results to more than one journal concurrently is unethical. Exceptions are the review articles. Authors may not present results obtained by others as if they were their own. Authors should acknowledge the work of others used in their research and cite publications that have influenced the direction and course of their study.

Plagiarism is not tolerated. All manuscripts submitted to Opto-Electronics Review will be checked for plagiarism (copying text or results from other sources) and self-plagiarism (duplicating substantial parts of authors’ own published work without giving the appropriate references) using the CrossCheck database (iThenticate plagiarism checker).

Duplicate submission

Simultaneous submissions of the same manuscript to different journals will not be tolerated. The submitted article will be removed without consideration.

Corrections and retractions

All authors have an obligation to inform and cooperate with journal editors to provide prompt retractions or correction of errors in published works.

• The journal will issue retractions if:

• There is clear evidence that the findings are unreliable, either as a result of misconduct (e.g., data fabrication or honest error - miscalculation or experimental error);

• The findings have previously been published elsewhere without proper cross-referencing, permission or justification (i.e., cases of redundant publication);

• It constitutes plagiarism;

• It reports unethical research.

• The journal will issue errata, if:

• A small portion of an otherwise reliable publication proves to be misleading (especially because of honest error);

• The author list is incorrect.

Other forms of misconduct include failure to meet clear ethical and legal requirements such as misrepresentation of interests, breach of confidentiality, lack of informed consent and abuse of research subjects or materials. Misconduct also includes improper dealing with infringements, such as attempts to cover up misconduct and reprisals on whistleblowers.

The primary responsibility for handling research misconduct is in the hands of those who employ the researchers. If a possible misconduct is brought to our attention, we will seek advice from the referees and the Editorial Board. If there is the evidence, we will resolve the matter by appropriate corrections in the printed and online journal; by refusing to consider an author's future work and by contacting affected authors and editors of other journals.

Human and Animal Rights

If the work involves the use of human subjects, the author should ensure that the work described has been carried out in accordance with The Code of Ethics of the World Medical Association (Declaration of Helsinki) for experiments involving humans; Uniform Requirements for manuscripts submitted to Biomedical journals. Authors should include a statement in the manuscript that informed consent was obtained for experimentation with human subjects. The privacy rights of human subjects must always be observed.

All animal experiments should comply with the ARRIVE guidelines and should be carried out in accordance with the EU Directive 2010/63/EU for animal experiments, and the authors should clearly indicate in the manuscript that such guidelines have been followed.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji