Nauki Techniczne

Chemical and Process Engineering

Zawartość

Chemical and Process Engineering | 2020 | vol. 41 | No 3 |

Abstrakt

The article presents an experimental investigation of the rheological properties of carbomer microgels. All of the tested fluids were made up from commercial polyacrylic acid, Carbopol Ultrez 30. In total, eighteen microgels were prepared, differing in concentration; 0.2, 0.4 and 0.6 wt%, with six levels of neutralisation for pH from 4.0 to 9.0. Based on the experimental flow curves it was found that all tested microgels are yield stress shear-thinning fluids. Therefore, the Herschel–Bulkley model was used and its rheological parameters were determined. It was found that both the concentration and the pH value significantly affected the yield stress. As the Carbopol concentration increased, the yield point also increased. With the increasing value of pH, the yield stress first increased until a certain maximum level and then decreased. The maximum values of yield stress were obtained for pH = 6 to 7, depending on polymer concentration. It was also found that flow curves of the tested microgels could be described using one universal master curve, thus they have common rheological behaviour.

Przejdź do artykułu

Autorzy i Afiliacje

Anna Story
Grzegorz Story
Zdzisław Jaworski

Abstrakt

The use of ammonium nitrate due to its high nitrogen content (> 26%) has made it the most utilized fertilizer in agricultural areas. However, being easily accessible with this feature encouraged its use for different purposes. Ammonium nitrate is usually produced with large tonnage (> 50 ton/h) and high cost (> $20 million) production processes. Therefore, any changes that can be made in the process must be applied in the process so that the result can be achieved easily without increasing the cost in any way. In this study, it is aimed to reduce the explosion sensitivity of ammonium nitrate used for explosive purposes in terrorist attacks. Thus, it was aimed to solve the problem by adding various chemicals to the ammonium nitrate production process so that it can only be used for agricultural purposes. For this purpose, the production process was examined by adding carboxymethyl cellulose and polyethylene glycol to the ammonium nitrate production process and the accuracy of the results was tested by instrumental analysis methods.

Przejdź do artykułu

Autorzy i Afiliacje

Ahmet Ozan Gezerman

Abstrakt

Greenhouse gases such as carbon dioxide and water vapour can be captured from gas streams on a zeolite 13X adsorbent. Experimental water vapour adsorption isotherms and kinetic curves were measured in the temperature range of 293–393 K and pressure up to 2100 Pa. The equilibrium data were developed with Toth and Sips multi-temperature isotherm models. The results of the process rate studies were described using pseudo-first and pseudo-second order kinetic models. Findings were compared with our own results of CO2 adsorption studies on the same zeolite.

Przejdź do artykułu

Autorzy i Afiliacje

Kamila Zabielska
Tomasz Aleksandrzak
Elżbieta Gabruś

Abstrakt

The cyclic Electrothermal Temperature Swing Adsorption (ETSA) process in a fixed-bed column with Supersorbon K40 activated carbon (AC) was applied to remove propan-2-ol (IPA) from air. The bed was electrothermally regenerated using direct resistive heating method. The tests were performed in the range of operating parameters: IPA loading 0.18-0.26 kg/kg, voltage 19.5 V, set-point temperature 393–403 K, nitrogen flow rate 0.12 m3/h.

The analysis revealed, that raising the bed temperature resulted in an increase of desorption degree of adsorbate, reduction of regeneration time and an increase in the energy consumption. The application of insulation enabled reduction of energy consumption and regeneration time by 27% and 10%, respectively.

Przejdź do artykułu

Autorzy i Afiliacje

Krzysztof Kowalski
Elżbieta Gabruś
Dorota Downarowicz

Abstrakt

A two-parameter continuation method was developed and shown in the form of an example, allowing determination of Hopf bifurcation sets in a chemical reactor model. Exemplary calculations were made for the continuous stirred tank reactor model (CSTR). The set of HB points limiting the range of oscillation in the reactor was determined. The results were confirmed on the bifurcation diagram of steady states and on time charts. The method is universal and can be used for various models of chemical reactors.

Przejdź do artykułu

Autorzy i Afiliacje

Marek Berezowski

Abstrakt

The paper presents a comparative analysis to determine the optimal temperatures and the activation energies for various origin endo-inulinases from Aspergillus niger. The parameters were estimated based on the literature of the activity curves vs. temperature for hydrolysis of inulin. It was assumed that both the hydrolysis reaction process and the deactivation process of endo-inulinase were first-order reactions by the enzyme concentration. A mathematical model describing the effect of temperature on endo-inulinases from Aspergillus niger activity was used. Based on the comparison analysis, values of the activation energies Ea were in the range from 23:53  3:20 kJ/mol to 50:66  3:61 kJ/mol, the deactivation energies Ed were in the range from 88:42  5:03 kJ/mol to 142:87  2:75 kJ/mol and the optimum temperatures Topt were obtained in the range from 317:12  0:83 K to 332:55  0:72 for endo-inulinase A. niger.

Przejdź do artykułu

Autorzy i Afiliacje

Justyna Miłek

Redakcja

Editor-in-Chief
Andrzej K. Biń, Warsaw University of Technology, Poland

Editorial Board
Andrzej Burghardt (Chairman), Polish Academy of Sciences, Gliwice, Poland
Jerzy Bałdyga, Warsaw University of Technology, Poland
Andrzej Górak, T.U. Dortmund, Germany
Leon Gradoń, Warsaw University of Technology, Poland
Andrzej Jarzębski, Silesian University of Technology, Poland
Zdzisław Jaworski, West Pomeranian University of Technology, Szczecin, Poland
Władysław Kamiński, Technical University of Łódź, Poland
Stefan Kowalski, Poznań University of Technology, Poland
Andrzej Krasławski, Lappeenranta University of Technology, Finland
Stanisław Ledakowicz, Technical University of Łódź, Poland
Eugeniusz Molga, Warsaw University of Technology, Poland
Alvin W. Nienow, University of Birmingham, United Kingdom
Andrzej Noworyta, Wrocław University of Technology, Poland
Ryszard Pohorecki, Warsaw University of Technology, Poland
Andrzej Stankiewicz, Delft University of Technology, The Netherlands
Czesław Strumiłło, Technical University of Łódź, Poland
Stanisław Sieniutycz, Warsaw University of Technology, Poland
Krzysztof Warmuziński, Polish Academy of Sciences, Gliwice, Poland
Laurence R. Weatherley, University of Kansas, Lawrence, United States
Günter Wozny, T.U. Berlin, Germany
Ireneusz Zbiciński, Technical University of Łódź, Poland

Technical Editor
Barbara Zakrzewska, West Pomeranian University of Technology, Szczecin, Poland
Language Editor
Marek Stelmaszczyk, West Pomeranian University of Technology, Szczecin, Poland

 

Kontakt

Editorial Office
ul. Waryńskiego 1
00-645 Warszawa
Poland
email: andrzej.bin@outlook.com

 

Instrukcje dla autorów

All manuscripts submitted for publication in Chemical and Process Engineering must comprise a description of original research that has neither been published nor submitted for publication elsewhere.

The content, aim and scope of the proposals should comply with the main subject of the journal, i.e. they should deal with mathematical modelling and/or experimental investigations on momentum, heat and mass transfer, unit processes and operations, integrated processes, biochemical engineering, statics and kinetics of chemical reactions. The experiments and modelling may cover different scales and processes ranging from the molecular phenomena up to production systems. The journal language is grammatically correct British English.

Chemical and Process Engineering publishes: i) full text research articles, ii) invited reviews, iii) letters to the editor and iv) short communications, aiming at important new results and/or applications. Each of the publication form is peer-reviewed by at least two independent referees.  

Submission of materials for publication

The manuscripts are submitted for publication via e-mail address andrzej.bin@outlook.com. When writing the manuscript, authors should preferably use the template for articles.The manuscripts are submitted for publication via e-mail address andrzej.bin@outlook.com. When writing the manuscript, authors should preferably use the template for articles. 

Proposals of a paper should be uploaded using the Internet site of the journal and should contain:

  • a manuscript file in Word format (*.doc, *.docx),
  • the manuscript mirror in PDF format,
  • all graphical figuresin separate graphics files.

In the following paragraphthe general guidelines for the manuscript preparation are presented.

Manuscript outline

        1. Header details
          1. Title of paper
          2. Names (first name and further initials) and surnames of authors
          3. Institution(s) (affiliation)
          4. Address(es) of authors
          5. Information about the corresponding author; academic title, name and surname, email address, address for correspondence
        2. Abstract – should contain a short summary of the proposed paper. In the maximum of 200 words the authors should present the main assumptions, results and conclusions drawn from the presented study.
        3. Keywords– Up to 5 characteristic keyword items should be provided.
        4. Text
          1. Introduction. In this part, description of motivation for the study and formulation of the scientific problem should be included and supported by a concise review of recent literature.
          2. Main text. It should contain all important elements of the scientific investigations, such as presentation of experimental rigs, mathematical models, results and their discussion. This part may be divided into subchapters.
          3. Conclusions. The major conclusions can be put forward in concise style in a separate chapter. Presentation of conclusions from the reported research work accompanied by a short commentary is also acceptable.
          4. Figures: drawings, diagrams and photographs can be in colour and should be located in appropriate places in the manuscript text according. Their graphical form should be of vector or raster type with the minimum resolution of 900 dpi. In addition, separate files containing each of the drawings, graphs and photos should be uploaded onto the journal Web site in one of the following formats: bmp, gif, tiff, jpg, eps. Due to rigid editorial reasons, graphical elements created within MS Word and Excel are not acceptable. The final length of figures should be intended typically for 8 cm (single column) or 16 cm in special cases of rich-detail figures. The basic font size of letters in figures should be at least 10 pts after adjusting graphs to the final length.  

          Figures: drawings, diagrams and photographs should be in gray scale. In case of coloured graphs or photo an additional payment of 300 PLN (72 €) per 1 page containing coloured figures on both sides, or 150 PLN (36 €) per page containing coloured figures on one side will be required.

          Tables should be made according to the format shown in the template.

        5. All figures and tables should be numbered and provided with appropriate title and legend, if necessary. They have to be properly referenced to and commented in the text of the manuscript.

        6. List of symbols should be accompanied by their units
        7. Acknowledgements may be included before the list of literature references
        8. Literature citations

 

The method of quoting literature source in the manuscript depends on the number of its authors:

  • single author – their surname and year of publication should be given, e.g. Marquardt (1996) or (Marquardt, 1996),
  • two authors – the two surnames separated by the conjunction “and” with the publication year should be given, e.g. Charpentier and McKenna (2004) or (Charpentier and McKenna, 2004),
  • three and more authors – the surname of the first author followed by the abbreviation “et al.” and year of publication should be given, e.g. Bird et al. (1960) or (Bird et al., 1960).

In the case of citing more sources in one bracket, they should be listed in alphabetical order using semicolon for separation, e.g. (Bird et al., 1960; Charpentier and McKenna, 2004; Marquardt, 1996). Should more citations of the same author(s) and year appear in the manuscript then letters “a, b, c, ...” should be successively applied after the publication year.

Bibliographic data of the quoted literature should be arranged at the end of the manuscript text in alphabetic order of surnames of the first author. It is obligatory to indicate the DOI number of those literature items, which have the numbers already assigned. Journal titles should be specified by typingtheir right abbreviationsor, in case of doubts, according to the List of Title Word Abbreviations available at http://www.issn.org/2-22661-LTWA-online.php.

Examples of citation for:

Articles
Charpentier J. C., McKenna T. F., 2004.Managing complex systems: some trends for the future of chemical and process engineering. Chem. Eng. Sci., 59, 1617-1640. DOI: 10.1016/j.ces.2004.01.044.

Information from books (we suggest adding the page numbers where the quoted information can be found)
Bird R. B., Stewart W.E., Lightfood E.N., 2002. Transport Phenomena. 2nd edition, Wiley, New York, 415-421.

Chapters in books
Hanjalić K., Jakirlić S., 2002. Second-moment turbulence closure modelling, In: Launder B.E., Sandham N.D. (Eds.), Closure strategies for turbulent and transitional flows. Cambridge University Press, Cambridge, 47-101.

Conferences
ten Cate A., Bermingham S.K., Derksen J.J., Kramer H.M.J., 2000. Compartmental modeling of an 1100L DTB crystallizer based on Large Eddy flow simulation. 10th European Conference on Mixing. Delft, the Netherlands, 2-5 July 2000, 255-264.

Payments

Starting from 2014 a principle of publishing articles against payment is introduced, assuming non-profit making editorial office. According to the principle authors or institutions employing them, will have to cover the expenses amounting to 40 PLN (or 10 €) per printed page. The above amount will be used to supplement the limited financial means received from the Polish Academy of Sciences for the editorial and publishing; and in particular to increase the capacity of the next CPE volumes and to proofread the linguistic correctness of the articles. The method of payment will be indicated in an invoice sent to the authors or institutions after acceptance of their manuscripts to be published. In justifiable cases presented in writing, the editorial staff may decide to relieve authors from basic payment, either partially or fully. All correspondence should be sent to Editor-in-Chief, Prof. Andrzej K. Biń, email address: andrzej.bin@outlook.com.


Ta strona wykorzystuje pliki 'cookies'. Więcej informacji