Definition of a composite [1] describes an ideal composite material with perfect structure. In real composite materials, structure is usually imperfect – composites contain various types of defects [2, 3–5], especially as the casted composites are of concern. The reason for this is a specific structure of castings, related to course of the manufacturing process. In case of metal matrix composite castings, especially regarding these manufactured by saturation, there is no classification of these defects [2, 4]. Classification of defects in castings of classic materials (cast iron, cast steel, non-ferrous alloys) is insufficient and requires completion of specific defects of mentioned materials. This problem (noted during manufacturing metal matrix composite castings with saturated reinforcement in Institute of Basic Technical Sciences of Maritime University Szczecin) has become a reason of starting work aimed at creating such classification. As a result, this paper was prepared. It can contribute to improvement of quality of studied materials and, as a consequence, improve the environment protection level.
Heavy steel castings deoxidized with aluminium are sometimes brittle intercrystalline failed during their service along primary grain boundaries what is initiated by aluminium nitrides and so called conchoidal fractures are formed. The tendency to forming the conchoidal fractures depends in particular on cooling rate (the casting modulus), aluminium and nitrogen contents in steel. During deoxidation, when manufacturing heavy castings, the elements with high affinity to nitrogen, zirconium or titanium, are added to steel that would decrease nitrogen activity by the bond on stable nitrides. The formation of stable nitrides should reduce the tendency of steel to the formation of conchoidal fractures. Deoxidation was thermodynamically analyzed at presence of the mentioned elements. For particular conditions a probable course of deoxidation was estimated at test castings. The deoxidation course was checked by microanalysis of deoxidation products (inclusions). For service and experimental castings the anticipated composition of inclusions was compared. It has been proved that in heavy castings with high aluminium contents in steel under studied conditions neither the addition of zirconium nor of titanium nor of rare earth metals will prevent the formation of conchoidal fractures.
The paper, which is a summary and supplement of previous works and research, presents the results of numerical and physical modeling of the GX2CrNiMoCuN25-6-3 duplex cast steel thin-walled castings production. To obtain thin-walled castings with wall in the thinnest place even below 1 mm was used the centrifugal casting technology and gravity casting. The analyzed technology (centrifugal casting) enables making elements with high surface quality with reduced consumption of batch materials and, as a result, reducing the costs of making a unitary casting. The idea behind the production of cast steel with the use of centrifugal technology was to find a remedy for the problems associated with unsatisfactory castability of the tested alloy.
The technological evaluation of the cast construction was carried out using the Nova Flow & Solid CV 4.3r8 software. Numerical simulations of crystallization and cooling were carried out for a casting without a gating system and sinkhead located in a mold in accordance with the pouring position. It was assumed that the analyzed cast will be made in the sand form with dimensions 250×250×120 mm.
While analyzing shape accuracy of ferroalloy precision castings in terms of ceramic moulds physical anisotropy, low-alloy steel castings
("cover") and cast iron ("plate") were included. The basic parameters in addition to the product linear shape accuracy are flatness
deviations, especially due to the expanded flat surface which is cast plate. For mentioned castings surface micro-geometry analysis was
also carried, favoring surface load capacity tp50 for Rmax = 50%.
Surface load capacity tp50 obtained for the cast cover was compared with machined product, and casting plate surface was compared with
wear part of the conveyor belt. The results were referred to anisotropy of ceramic moulds physical properties, which was evaluated by
studying ceramic moulds samples in computer tomography equipment Metrotom 800.
Inconel 713C alloy belongs to the group of materials with high application potential in the aerospace industry. This nickel alloy has excellent features such as high strength, good surface stability, high creep and corrosion resistance. The paper presents the results of metallographic examinations of a base material and padding welds made by laser beam on the Inconel 713C alloy. The tests were made on precisely cast test plates imitating low - pressure turbine blades dedicated for the aerospace industry. Observations of the macro- and microstructure of the padding welds, heat-affected zone and base material indicate, that the Inconel 713C alloy should be classified as a hard-to-weld material. In the investigated joint, cracking of the material is disclosed mainly in the heat-affected zone and at the melted zone interface, where pad weld crystals formed on partially melted grains. The results show that phases rich with chromium and molybdenum were formed by high temperature during welding process, which was confirmed by EDS analysis of chemical composition.
Consecutive casting of bimetallic applies consecutive sequences of pouring of two materials into a sand mold. The outer ring is made of NiHard1, whereas the inner ring is made of nodular cast iron. To enable a consecutive sequence of pouring, an interface plate made of low carbon steel was inserted into the mold and separated the two cavities. After pouring the inner material at the predetermined temperature and the interface had reached the desired temperature, the NiHard1 liquid was then poured immediately into the mold. This study determines the pouring temperature of nodular cast iron and the temperature of the interface plate at which the pouring of white cast iron into the mold should be done. Flushing the interface plate for 2 seconds by flowing nodular cast iron liquid as inner material generated a diffusion bonding between the inner ring and interface plate at pouring temperatures of 1350 °C, 1380 °C, and 1410 °C. The interface was heated up to a maximum temperature of 1242 °C, 1260 °C, and 1280 °C respectively. The subsequent pouring of white cast iron into the mold to form the outer ring at the interface temperature of 1000 °C did not produce a sufficient diffusion bonding. Pouring the outer ring at the temperature of 1430°C and at the interface plate temperature of 1125 °C produced a sufficient diffusion bonding. The presence of Fe3O2 oxide on the outer surface of the interface material immediately after the interface was heated above 900 ⁰C has been identified. Good metallurgical bonding was achieved by pouring the inner ring at the temperature of 1380°C, interface temperature of 1125 °C and then followed by pouring of the outer ring at 1430⁰C and flushing time of 7 seconds.
This paper presents a new stand for studying the linear shrinkage kinetics of foundry alloys. The stand is equipped with a laser displacement sensor. Thanks to this arrangement, the measurement is of a contactless nature. This solution allows for the elimination of errors which occur in measurements made using intermediary elements (steel rods). The supposition of the expansion (shrinkage) of the sample and the expansion of the heated rod lead to the distortion of the image of the actual dimensional changes of the studied sample. A series of studies of foundry alloys conducted using the new stand allowed a new image of shrinkage kinetics to be obtained, in particular regarding cast iron. The authors introduce in the study methodology a real-time measurement of two linked quantities; shrinkage (the displacement of the free end of the sample) and temperature in the surface layer of the sample casting. This generates not only a classic image of shrinkage (S) understood as S = f (t), but also the view S = f (T). The latter correlation, developed based on results obtained using the contactless method, provide a new, so far poorly known image of the course of shrinkage in foundry alloys, especially cast iron with graphite in the structure. The study made use of hypo- and hypereutectic cast iron in order to generate an image of the differences which occur in the kinetics of shrinkage (as well as in pre-shrinkage expansion - expansion occurs during solidification).
The temperature of liquid steel for continuous casting determines the casting speed and cooling conditions. The failure to meet the required casting process parameters may result in obtaining slabs of inconsistent quality. Numerical methods allow for real processes to be modelled. There are professional computer programs on the market, so the results of the simulations allow us to understand the processes that occur during casting and solidification of a slab. The study attempts to evaluate the impact of the superheat temperature on the slab structure based on the industrial operating parameters of the continuous casting machine.
This article is a description of the progress of research and development in the area of massive large-scale castings - slag ladles implemented in cooperation with the Faculty of Foundry Engineering of UST in Krakow. Slag ladles are the one of the major castings that has been developed by the Krakodlew (massive castings foundry) for many years. Quality requirements are constantly increasing in relation to the slag ladles. Slag ladles are an integral tool in the logistics of enterprises in the metallurgical industry in the process of well-organized slag management and other by-products and input materials. The need to increase the volume of slag ladles is still growing. Metallurgical production is expected to be achieved in Poland by 2022 at the level of 9.4 million Mg/year for the baseline scenario - 2016 - 9 million Mg/year. This article describes the research work carried out to date in the field of technology for the production of massive slag ladles of ductile cast iron and cast steel.
The paper presents recent developments concerning the formation of surface layer in austempered ductile iron castings. It was found that the traditional methods used to change the properties of the surface layer, i.e. the effect of protective atmosphere during austenitising or shot peening, are not fully satisfactory to meet the demands of commercial applications. Therefore, new ways to shape the surface layer and the surface properties of austempered ductile iron castings are searched for, to mention only detonation spraying, carbonitriding, CVD methods, etc.
Inconel 713C precision castings are used as aircraft engine components exposed to high temperatures and the aggressive exhaust gas
environment. Industrial experience has shown that precision-cast components of such complexity contain casting defects like
microshrinkage, porosity, and cracks. This necessitates the development of repair technologies for castings of this type. This paper
presents the results of metallographic examinations of melted areas and clad welds on the Inconel 713C nickel-based superalloy, made by
TIG, plasma arc, and laser. The cladding process was carried out on model test plates in order to determine the technological and materialrelated
problems connected with the weldability of Inconel 713C. The studies included analyses of the macro- and microstructure of the
clad welds, the base materials, and the heat-affected zones. The results of the structural analyses of the clad welds indicate that Inconel
713C should be classified as a low-weldability material. In the clad welds made by laser, cracks were identified mainly in the heat-affected
zone and at the melted zone interface, crystals were formed on partially-melted grains. Cracks of this type were not identified in the clad
welds made using the plasma-arc method. It has been concluded that due to the possibility of manual cladding and the absence of welding
imperfections, the technology having the greatest potential for application is plasma-arc cladding.
The paper presents the production problems related to casting using precision casting methods. The essential adverse effect of the casting
process is the presence of burrs understood as oversize material necessary to remove the next finishing operations. In addition, the surfaces
of the cast often characterized by a porous structure. One of the methods to improve the smoothness of the area proposed by the authors is
the use of vibro-abrasive finishing. This type of treatment is widely used in the treatment of finishing small objects as well as complex
shapes. Objects in the form of casting in the first step was treated with aggressive deburring polyester matrix abrasive media. The second
stage was polishing, with using smoothing porcelain media. The study evaluated the effect of vibro-abrasive machining typical cast on the
basic parameters of the geometric structure of the surface. Observations using optical microscope Nicon Eclipse MA 200 compared
changes in surface microstructure and the effect of deburring. Clearly we can say that vibro-abrasive machining an effective way
of reducing the size of burrs, smoothing and lightening the surface of objects made by casting.
Air abrasion process is used for cleaning casting surface of prosthetic components, and to prepare the surface of these elements for the
application of veneering items. Its side effect, however, is that abrasive particles are embedded in the treated surface, which can be up to
30% of the surface and it constitutes the side effect of this procedure. Such a significant participation of foreign material can not be
indifferent to the properties of the surface. Embedded particles can be the place of stress concentration causing cracking of ceramics, and
may deteriorate corrosion resistance by forming corrosive microlinks. In the latter cases, it would be advisable to remove elements
embedded into the surface. The simplest method is chemical etching or electrochemical one. Nevertheless, these procedures should not
significantly change the parameters of the surface. Among many possible reagents only a few fulfills all the above conditions. In addition,
processing should not impair corrosion resistance of titanium, which is one of the most important factors determining its use as a prosthetic
restoration in the mouth. The study presented results of corrosion resistance of titanium used to make prosthetic components by means of
casting method, which were subjected to chemical processing designed to remove the embedded abrasive particles. The aim of the study
was to investigate whether etching with selected reagents affects the corrosion resistance of titanium castings. For etching the following
reagents were used: 30% HNO3 + 3% HF + H2O, HNO3+ HF+ glycerol (1:2:3), 4% HF in H2O2, 4% HF in H2O, with a control
sandblasted sample, not subjected to etching. Tests demonstrated that the etching affected corrosion properties of test samples, in each case
the reduction of the corrosion potential occurred - possibly due to the removal of particles of Al2O3 from the surface and activation of the
surface. None of the samples underwent pitting corrosion as a result of polarization to 9 V. Values of the polarization resistance, and
potentiodynamic characteristics indicated that the best corrosion resistance exhibited the samples after etching in a mixture of 4% solution
of HF in H2O2. They showed very good passivation of the surface.
The article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1055) castings used for marine propellers.
Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the
alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich κ−phase precipitates in bronze microstructure
significantly affect its mechanical properties. With an increase in the number of small κ−phase precipitates increases the tensile strength of
castings, while the presence of large globular precipitates improves ductility. Fragmentation and shape of κ−phase precipitates depends on
many factors, particularly on the chemical composition of the alloy, Fe/Ni ratio, cooling rate and casting technology.
The article is a case study of the steel milling ring casting of about 6 tonnes net weight. The casting has been cast in the steel foundry the authors have been cooperating with. The aim was to analyse the influence of the shape of the chills and the material which was used to make them on the casting crystallization process. To optimally design the chills the set of the computer simulation has been carried out with 3 chills’ shape versions and 3 material’s versions and the results have been compared with the technology being in use (no chills). The proposed chills were of different thermal conductivity from low to high. Their shapes were obviously dependant on the adjacent casting surface geometry but were the result of the attempt to optimise their effect with the minimum weight, too. The chills working efficiency was analysed jointly with the previously designed top feeders system. The following parameters have been chosen to compare their effectiveness and the crystallization process: time to complete solidification and so-called fed volume describing the casting feeding efficiency. The computer simulations have been carried out with use of MagmaSoft v. 5.2 software. Finally, the optimisation has led to 15% better steel yield thanks to 60% top feeders weight reduction and 40% shorter solidification time. The steel ring cast with use of such technology fulfil all quality criteria.
In this work, the effects of 75 mm thick cast iron, (casting mould YIV) composition (Cu) and heat treatment were investigated on the microstructure and mechanical properties (hardness, elongation, tensile strength, yield strength) of ductile iron castings. As a result of adding Cu, the amount of pearlite is at 80% reduces of amount of ferrite. Normalizing of non-alloy cast iron increases the amount of pearlite to 70%. It also, increases tensile strength (659 MPa) and hardness (248 HB). Studied metallographic crossections were made from the grip sections of the tensile specimens. The structure composition and the characteristics of graphite were determined by computer image analysis. Measurements of graphite of non-alloy cast iron after normalizing and in cooper cast iron indicate the approximate amount of precipitates of graphite and their approximate average diameters. The applied normalizing and the additive alloy (Cu) were established to give comparable mechanical properties and structure of matrix in thick-walled castings.
Simulation software can be used not only for checking the correctness of a particular design but also for finding rules which could be used
in majority of future designs. In the present work the recommendations for optimal distance between a side feeder and a casting wall were
formulated. The shrinkage problems with application of side feeders may arise from overheating of the moulding sand layer between
casting wall and the feeder in case the neck is too short as well as formation of a hot spot at the junction of the neck and the casting. A
large number of simulations using commercial software were carried out, in which the main independent variables were: the feeder’s neck
length, type and geometry of the feeder, as well as geometry and material of the casting. It was found that the shrinkage defects do not
appear for tubular castings, whereas for flat walled castings the neck length and the feeders’ geometry are important parameters to be set
properly in order to avoid the shrinkage defects. The rules for optimal lengths were found using the Rough Sets Theory approach,
separately for traditional and exothermic feeders.
Simulation software dedicated for design of casting processes is usually tested and calibrated by comparisons of shrinkage defects
distribution predicted by the modelling with that observed in real castings produced in a given foundry. However, a large amount of
expertise obtained from different foundries, including especially made experiments, is available from literature, in the form of
recommendations for design of the rigging systems. This kind of information can be also used for assessment of the simulation predictions.
In the present work two parameters used in the design of feeding systems are considered: feeding ranges in horizontal and vertical plates as
well as efficiency (yield) of feeders of various shapes. The simulation tests were conducted using especially designed steel and aluminium
castings with risers and a commercial FDM based software. It was found that the simulations cannot predict appearance of shrinkage
porosity in horizontal and vertical plates of even cross-sections which would mean, that the feeding ranges are practically unlimited. The
yield of all types of feeders obtained from the simulations appeared to be much higher than that reported in the literature. It can be
concluded that the feeding flow modelling included in the tested software does not reflect phenomena responsible for the feeding processes
in real castings properly. Further tests, with different types of software and more fundamental studies on the feeding process modelling
would be desirable.