The paper deals with a study of the effect of regulating elements on local values of heat transfer coefficients along shaped heat exchange surfaces with forced air convection. The use of combined methods of heat transfer intensification, i.e. a combination of regulating elements with appropriately shaped heat exchange areas seems to be highly effective. The study focused on the analysis of local values of heat transfer coefficients in indicated cuts, in distances expressed as a ratio x/s for 0; 0.33; 0.66 and 1. As can be seen from our findings, in given conditions the regulating elements can increase the values of local heat transfer coefficients along shaped heat exchange surfaces. An optical method of holographic interferometry was used for the experimental research into temperature fields in the vicinity of heat exchange surfaces. The obtained values correspond very well with those of local heat transfer coefficients αx, recorded in a CFD simulation.

This paper shows the result of work of the Institute of Micromechanics and Photonics at Warsaw University of Technology and the Length and Angle Division of Central Office of Measures (GUM) [1] in building an automatic multiwavelength interferometric system with extended measurement range for calibration of long (up to 1 m) gauge blocks. The design of a full working setup with environmental condition control and monitoring systems, as well as image analysis software, is presented. For length deviation determination the phase fraction approach is proposed and described. To confirm that the system is capable of calibrating gauge blocks with assumed accuracy, a comparison between the results of 300 mm length gauge block measurement obtained by using other systems from the Central Office of Measures is made. Statistical analysis proved that the system can be used for high precision measurements with assumed standard uncertainty (125 nm for a length of 1 m). Finally the comparison between our results obtained for a long gauge block set (600 mm to 1000 mm long) and previous calibrations made by the Physikalisch-Technische Bundesanstalt (PTB) [2] is shown

In this paper, we present a fibre-optic sensor for simultaneous measurement of refractive index and thickness of liquid layers.We designed an experimental low-coherence setup with two broadband light sources and an extrinsic fibre-optic Fabry–Pérot interferometer acting as the sensing head.We examined how the refractive index of a liquid film and its thickness affect spectrum at the output of a fibre-optic interferometer. We performed a series of experiments using two light sources and only one sensing head. The spectra were collected in ranges of 1220÷1340 nm and 1500÷1640 nm. The obtained results show that using two spectra recorded simultaneously for two wavelength ranges enables to determine thickness in a range of 50÷500 μm, and refractive index of a liquid film in a range of 1:00÷1:41 RIU using only one sensing head.

Dzięki niej astronomowie publikują radiowe mapy nieba z setkami tysięcy dotychczas nieznanych galaktyk.

This contribution deals with the heat transfer parameters and pressure losses in heat exchange sets with six geometrical arrangements at low Re values (Re from 476 to 2926). Geometrical arrangements were characterised by the h/H ratio ranging from 0.2 to 1.0. The experiments used the holographic interferometry method in real time. This method enables visible and quantitative evaluations of images of temperature fields in the examined heat exchange. These images are used to determine the local and mean heat transfer parameters. The obtained data were used to determine the Colburn j-factor and the friction coefficient f. The measured values show that by using the profiled heat exchange surfaces and inserting regulating tubes, an intensification of heat transfer (increase of Num, and/or j) was achieved. However, pressure losses recorded a significant increase (increase of f).

In situ monitoring of the thickness of thin diamond films during technological processes is important because it allows better control of deposition time and deeper understanding of deposition kinetics. One of the widely used techniques is laser reflectance interferometry (LRI) which enables non-contact measurement during CVD deposition. The authors have built a novel LRI system with a 405 nm laser diode which achieves better resolution compared to the systems based on He-Ne lasers, as reported so far. The system was used for in situ monitoring of thin, microcrystalline diamond films deposited on silicon substrate in PA-CVD processes. The thickness of each film was measured by stylus profilometry and spectral reflectance analysis as a reference. The system setup and interferometric signal processing are also presented for evaluating the system parameters, i.e. measurement uncertainty, resolution and the range of measurable film thickness.

One of the most important parameters in the study of diffraction gratings is their optical efficiency. This paper analyzes the different manufacturing processes to cover gratings of Moiré interferometry and their influence on the quality and absolute efficiency of replicated gratings on the surfaces of specimens. The Moiré interferometry is a field measurement technique that has been used in many different fields such as applied mechanics, microelectronics, biomechanics or micromechanics, hence the importance of this study. The applied reflected coating was done by sputtering and aluminium vaporization processes. In this work different materials and thickness layers were analyzed. The obtained coatings have a high degree of reflectivity on the replicated gratings.

This article applies radar interferometry technologies implemented in the ENVI SARscape and SNAP software environment provided by the processing of data from the Sentinel-1 satellite. The study was carried out based on six radar images of Sentinel-1A and Sentinel -1B taken from September 2017 until February 2018 with an interval of one month and on the radar-module of the already mentioned SNAP software. The main input data for solving the considered problem are radar images received from the satellite Sentinel-1B on the territory of Stebnyk-Truskavets for six months with an interval of one month. Monitoring of the Earth’s surface using radar data of the Sentinel-1A with a synthesized aperture is implemented with the application of interferometric methods of Persistent Scatterers and Small baselines interferometry for estimating small displacements of the Earth’s surface and structures. The obtained quantitative and qualitative indicators of monitoring do not answer the processes that take place and lead to vertical displacements the six months but do provide an opportunity to assess the extent and trends of their development. The specification in each case can be accomplished by ground methods, which greatly simplify the search for sites with critical parameters of vertical displacements which can have negative consequences and lead to an emergency.

Generation of two identical ns laser pulses spaced by a single µs time interval by means of sequential switching of the output mirror transmittance in a diode-pumped Nd:YAG laser is reported, to our knowledge, for the first time. The theoretical study of the process of transmission losses switching is developed. This analysis confirms the possibility of generation of two identical Q-switched laser pulses with 100% efficiency with respect to the referenced single pulse energy. The detailed characterization of the laser in free-running, single and double Q-switching regimes is presented. The laser can be applied in different branches of metrology as PIV, LIBS or holographic interferometry.

Modern space measurement techniques like SLR, DORIS, VLBI and GNSS are used to study the tectonic plates. The determination of plate motion parameters (Φ, Λ, ω) from various geodetic measurements is outlined. This paper is the third part of our studies on estimating geodetic and geodynamic parameters; it regards an accuracy analysis of the determined Φ, Λ, ω parameters which describe motions of the tectonic plates using Very Long Base Interferometry (VLBI) technique. Prior to this, SLR and DORIS space measurement techniques were examined by authors. The study is based on the velocities of station positions, as included in a realization of the International Terrestrial Reference System– ITRF2008 forVLBI technique, published by the International Earth Rotation and Reference Systems Service (IERS). This model is made subject to an analysis in association with the APKIM2005 model. Six big plates, namely: Eurasian (EUAS), African (AFR), Australian (AUS), North American (NOAM), Pacific (PACF) and Antarctic (ANTC) were analysed. The results obtained in this analysis were compared with our previous estimations based on DORIS and SLR techniques and estimated according to the APKIM2005 model. Generally, all our three solutions based on SLR, DORIS and VLBI measurement techniques were found to be consistent.

We describe a new method to separate ballistic from the scattered photons for optical tissue characterization. It is based on the hypothesis that the scattered photons acquire a phase delay. The photons passing through the sample without scattering or absorption preserve their coherence so they may participate in interference. We implement a Mach−Zehnder experimental setup where the ballistic photons pass through the sample with the delay caused uniquely by the sample indices of refraction. We incorporate a movable mirror on the piezoelectric actuator in the sample arm to detect the amplitude of the modulation term. We present the theory that predicts the path−integrated (or total) concentration of the scattering and absorption centres. The proposed technique may characterize samples with transmission attenuation of ballistic photons by a factor of 10^-14.

Spatial light modulators (SLM) are devices used to modulate amplitude, phase or polarization of a light wave in space and time. Current SLMs are based either on MEMS (micro-electro-mechanical system) or LCD (liquid crystal display) technology. Here we report on the parameters, trends in development and applications of phase SLMs based on liquid crystal on silicon (LCoS) technology. LCoS technology was developed for front and rear projection systems competing with AMLCD (active matrix LCD) and DMD (Digital Mirror Device) SLM. The reflective arrangement due to silicon backplane allows to put a high number of pixels in a small panel, keeping the fill-factor ratio high even for micron-sized pixels. For coherent photonics applications the most important type of LCoS SLM is a phase modulator. In the paper at first we describe the typical parameters of this device and the methods for its calibration. Later we present a review of applications of phase LCoS SLMs in imaging, metrology and beam manipulation, developed by the authors as well as known from the literature. These include active and adaptive interferometers, a smart holographic camera and holographic display, microscopy modified in illuminating and imaging paths and active sensors.

Digital photoelasticity is an important optical metrology follow-up for stress and strain analysis using full-field digital photographic images. Advances in digital image processing, data acquisition, procedures for pattern recognition and storage capacity enable the use of the computer-aided technique in automation and facilitate improvement of the digital photoelastic technique. The objective of this research is to find new equations for a novel phase-shifting method in digital photoelasticity. Some innovations are proposed. In terms of phaseshifting, only the analyzer is rotated, and the other equations are deduced by applying a new numerical technique instead of the usual algebraic techniques. This approach can be used to calculate a larger sequence of images. Each image represents a pattern and a measurement of the stresses present in the object. A decrease in the mean errors was obtained by increasing the number of observations. A reduction in the difference between the theoretical and experimental values of stresses was obtained by increasing the number of images in the equations for calculating phase. Every photographic image has errors and random noise, but the uncertainties due to these effects can be reduced with a larger number of observations. The proposed method with many images and high accuracy is a good alternative to the photoelastic techniques.

We present an alternative method to detect and measure the concentration changes in liquid solutions. The method uses Digital Holographic Interferometry (DHI) and is based on measuring refractive index variations. The first hologram is recorded when a wavefront from light comes across an ordinary cylindrical glass container filled with a liquid solution. The second hologram is recorded after slight changing the liquid’s concentration. Differences in phase obtained from the correlation of the first hologram with the second one provide information about the refractive index variation, which is directly related to the changes in physical properties related to the concentration. The method can be used − with high sensitivity, accuracy, and speed − either to detect adulterations or to measure a slight change of concentration in the order of 0.001 moles which is equivalent to a difference of 0.003 g of sodium chloride in solutions. The method also enables to measure and calculate the phase difference among each pixel of two samples. This makes it possible to generate a global measurement of the phase difference of the entire sensed region.