Nauki Techniczne

Opto-Electronics Review

Zawartość

Opto-Electronics Review | 2019 | vol. 27 | No 1

Abstrakt

All normal dispersion (ANDi) and highly nonlinear chalcogenide glass photonic crystal fiber (PCF) is proposed and numerically investigated for a broad, coherent and ultra-flat mid-infrared supercontinuum generation. The proposed PCF consists of a solid core made of Ga8Sb32S60 glass surrounded by seven rings of air holes arranged in a triangular lattice. We show by employing the finite difference frequency domain (FDFD) method that the Ga8Sb32S60 PCF dispersion properties can be engineered by carefully adjusting the air holes diameter in the cladding region and ANDi regime is achieved over the entire range of wavelengths with a zero chromatic dispersion around 4.5 μm. Moreover, we demonstrate that injecting 50 fs width and 20 kW peak power laser pulses (corresponding to a pulse energy of 1.06 nJ) at a pump wavelength of 4.5 μm into a 1 cm long ANDi Ga8Sb32S60 PCF generates a broad, flat-top and perfectly coherent SC spectrum extending from 1.65 μm to 9.24 μm at the 20 dB spectral flatness. These results make the proposed Ga8Sb32S60 PCF an excellent candidate for various important mid-infrared region applications including mid-infrared spectroscopy, medical imaging, optical coherence tomography and materials characterization.

Przejdź do artykułu

Autorzy i Afiliacje

A. Medjouria
D. Abedb
Z. Becera

Abstrakt

The welcome and adaptation of optical wireless technology by the modern era has brought forward the concept of an inter-satellite free-space optical communication system. In the present work, I study the combined effect of selection of different operating wavelengths and detector types along with the pointing errors at the transmitter and receiver side on the performance of an inter-satellite free-space optical link. The link performance has been optimized by measuring and analyzing the bit error rate and quality-factor of received signal under different scenarios. Performance of the inter-satellite link has also been investigated considering different modulation formats and data rates for LEO and MEO distances.

Przejdź do artykułu

Autorzy i Afiliacje

S. Kaur

Abstrakt

Effect of annealing on the structural properties of arsenic-implanted mercury cadmium telluride film grown by molecular beam epitaxy was studied with the use of transmission electron microscopy and optical reflection. Strong influence of the graded-gap surface layer grown on top of the film on the behaviour of implantation-induced defects under arsenic activation annealing was revealed and interpreted.

Przejdź do artykułu

Autorzy i Afiliacje

I.I Izhninab
O.I. Fitsych
Z. Świątek
Y. Morgiel
O.Yu. Bonchyk
H.V. Savytskyy
K.D. Mynbaev
A.V. Voitsekhovskii
A.G. Korotaev
M.V. Yakushev
V.S. Varavin
S.A. Dvoretsky

Abstrakt

We demonstrated a tunable Q-switched ytterbium-doped fiber laser (YDFL) using MoWS2/rGO nanocomposite as passive saturable absorber. Further, the Mo1−xWxS2/rGO nanosheets, with x proportion of 0.2, are synthesized using hydrothermal exfoliation technique. The proposed nanocomposite-PVA based thin film is fabricated by mixing the MoWS2/rGO nanosheets with polyvinyl alcohol (PVA). The fabricated thin film is sandwiched between two fiber ferrules to realize the proposed saturable absorber (SA). Further, the proposed MoWS2/rGO-PVA based thin film SA exhibits a fast relaxation time and a high damage threshold which are suitable to realize a Q-switched pulsed laser with a tunable wavelength range of 10  nm that extends from 1028 nm to 1038 nm. For the highest pump power of 267.4 mW, the generated Q-switched pulses exhibit a narrow pulse width of 1.22 μs, the pulse repetition rate of 90.4 kHz, the highest pulse energy of 2.13  nJ and its corresponding average power of 0.193 mW. To the best of author’s knowledge, this is the first realization of a tunable Q-switching fiber laser in a 1 μm wavelength using MoWS2/rGO nanocomposite saturable absorber.

Przejdź do artykułu

Autorzy i Afiliacje

J. Mohanraja
V. Velmuruganb
S. Sivabalanc

Abstrakt

The article shows the comprehensive results of the experiments, conducted in order to select the appropriate metal layers, for back absorber contacts, to apply in flexible, thin-film photovoltaic cells based on cadmium telluride. Preliminary selection of investigated materials was made on the basis of general knowledge and physical data. Deposition techniques, as well as layer parameters, were adjusted to the specific flexible solar cell’s needs. Selected metal layers were deposited either by physical vapour deposition (PVD) or screen-printing method (SP) and tested in terms of their flexibility, thermal resistance, as well as adhesion to CdTe layer. Practical verification of selected configurations is proved by the complete construction of the device.

Przejdź do artykułu

Autorzy i Afiliacje

K. Znajdek
Maciej Sibiński
ORCID: ORCID
A. Kubiak
Ł. Ruta
Z. Lisik
D. Janczak

Abstrakt

The subject of the article is aspects of PV modules and cells measurement, with the use of natural sunlight. A light source is an important element during calibration and measurements of solar cells and modules. All designers of artificial light sources try to recreate natural light using so called measurement tables. The correctly performed measurement, i.e. meeting all the appropriate atmospheric conditions, guarantees obtaining the result with the use of a reference spectrum. The article has two main aims. The first aim of the article is to answer the question asked earlier - if the sunlight spectrum registered in appropriate conditions is so good that it serves as the reference spectrum - then, in practice, during measurements carried out with its use, certain problems occur regarding the correct measurement results or their interpretation. The second aim regards presenting detailed numeric procedures in order to enable readers to associate air mass with geographical coordinates and Local Solar Time of their study/laboratory location. Moreover, having the data from their local meteorological station, they will be able to estimate the occurrence of the measurement spectral error of the tested cell/module not only from the group referred to in the article but also for others, for which they have a dedicated characteristics of spectral response.

Przejdź do artykułu

Autorzy i Afiliacje

T. Rodziewicz
M. Rajfur

Abstrakt

Increasing interest, enthusiasm of sport lovers, and economics involved offer high importance to sports video recording and analysis. Being crucial for decision making, ball detection and tracking in soccer has become a challenging research area. This paper presents a novel deep learning approach for 2D ball detection and tracking (DLBT) in soccer videos posing various challenges. A new 2-stage buffer median filtering background modelling is used for moving objects blob detection. A deep learning approach for classification of an image patch into three classes, i.e. ball, player, and background is initially proposed. Probabilistic bounding box overlapping technique is proposed further for robust ball track validation. Novel full and boundary grid concepts resume tracking in ball_track_lost and ball_out_of_frame situations. DLBT does not require human intervention to identify ball from the initial frames unlike the most published algorithms. DLBT yields extraordinary accurate and robust tracking results compared to the other contemporary 2D trackers even in presence of various challenges including very small ball size and fast movements.

Przejdź do artykułu

Autorzy i Afiliacje

P.R. Kamble
A.G. Keskar
K.M. Bhurchandi

Abstrakt

One dimension solar cells simulator package (SCAPS) is used to study the possibility of carrying out thin CIGS solar cells with high and stable efficiency. In the first step, we modified the conventional ZnO:B/i-ZnO/CdS/SDL/CIGS/Mo structure by substituting the SDL layer with the P + layer, having a wide bandgap from 1 to l.12 eV. Then, we simulated the J-V characteristics of this new structure and showed how the electrical parameters are affected. Conversion efficiency of 18.46% is founded by using 1.1 μm of P + layer thickness. Secondly, we analyze the effect of increase thickness and doping density of CIGS, CdS and P +  layers on the electric parameters of this new structure. We show that only the short-circuit current density (JSC) and efficiency are improved, reaching respectively 34.68 mA/cm2 and 18.85%, with increasing of the acceptors density. Finally, we introduced 10 nm of various electron reflectors at the CIGS/Mo interface in the new structure to reduce the recombination of minority carriers at the back contact. High conversion efficiency of 23.34% and better stability are obtained when wide band-gap BSF is used.

Przejdź do artykułu

Autorzy i Afiliacje

N. Guirdjebaye
S. Ouédraogo
A. Teyou Ngoupo
G.L. Mbopda Tcheum
J.M.B. Ndjaka

Abstrakt

In article a two-dimensional photonic crystal (PhC) is considered and modelled as a new generation antireflection coating for optoelectronic devices. Traditional antireflective coatings (ARCs) reduce the reflection of the radiation only – the new generation of antireflective coatings should affect the distribution of the radiation also. Such functionality can be provided by the two-dimensional PhC which reduce the reflection and scatter transmitted light. Prior to the fabrication, the PhCs should be designed and analysed. Results of the analysis should provide quantitative means for choice of materials and design solutions. In work, we analyse the electromagnetic field distribution as Poynting vectors inside the materials of optoelectronic devices, in order to investigate the possibility of improving the construction of future optoelectronic devices. Furthermore, we calculate the reflection and transmission of that ARC. It’s a complex optic analysis of new generation of ARC. The numerical analysis has been performed with the FDTD method in Lumerical Software. In work, we consider the two-dimensional photonic crystal on the top surface of optoelectronic structures. We compared the results with the traditional ARC from these same parameters as PhC: thickness and material. As an example, we presented the application of modelled, photonic crystal, thin-film, GaAs solar cells with PhC on top. The efficiency of this solar cell, using the photonic crystal, was improved by 6.3% over the efficiency of this same solar cell without PhC. Thus, our research strongly suggests that the unique properties of the photonic crystal could be used as a new generation of ARC.

Przejdź do artykułu

Autorzy i Afiliacje

D. Przybylski
S. Patela

Abstrakt

Modern scintillator detectors act as an efficient tool for detection and measurement of ionizing radiations. ZnSe based materials have been found to be a promising candidate for scintillation applications. These scintillators show much-needed scintillation efficiency along with advantages such as high thermal and radiation stability, less-toxicity, non-hygroscopicity, emissions in the visible range and small decay time etc. Further, in quantum confinement regime, they show improvement in luminescent properties and size dependent emissions. In this review article, the attempt has been made to trace the progress of ZnSe based materials towards highly efficient quantum dot scintillators. Here, the fundamental process of scintillation has been explained. Factors such as doping, annealing, heavy ion irradiation which affects the scintillation response of ZnSe based scintillators have also been discussed. Method of synthesis plays a key role in optimization of quantum dot properties. Hence, it has been tried to trace the development in methods of synthesis of quantum dots. With optimized synthesis, we can extend applications of these highly efficient quantum dot scintillators for various scientific and industrial applications.

Przejdź do artykułu

Autorzy i Afiliacje

S. Jagtap
P. Chopade
S. Tadepalli
A. Bhalerao
S. Gosavi

Instrukcja dla autorów

Guide for Authors

https://www.editorialsystem.com/opelre/journal/for_authors/

OPTO-ELECTRONICS REVIEW is an open access journal. This involves the payment of an article publishing charge (APC) by the authors, their institution or funding body. We make the article freely available immediately upon publication on PAS Jornals platform (https://journals.pan.pl/opelre)

As of July 1st, 2024, there are changes in the fees for open access publications in Opto-Electronics Review: 2000 PLN (500 EUR) - up to 8 pages of the journal format and mandatory over-length charges of 200 PLN (50 EUR) per page (see the above link with instructions for Authors for details)

Articles submitted by June 30th, 2024: existing fee: 1750 PLN (or 400 EUR)

Articles submitted from July 1st, 2024: new fee: 2000 PLN (or 500 EUR) - a flat fee per paper up to 8 pages of the journal format (each additional page will be charged an additional 200 PLN or 50 EUR).

Dodatkowe informacje

Opto-Electronics Review was established in 1992 for the publication of scientific papers concerning optoelectronics and photonics materials, system and signal processing. This journal covers the whole field of theory, experimental verification, techniques and instrumentation and brings together, within one journal, contributions from a wide range of disciplines. Papers covering novel topics extending the frontiers in optoelectronics and photonics are very encouraged. The main goal of this magazine is promotion of papers presented by European scientific teams, especially those submitted by important team from Central and Eastern Europe. However, contributions from other parts of the world are by no means excluded.

Articles are published in OPELRE in the following categories:

-invited reviews presenting the current state of the knowledge,

-specialized topics at the forefront of optoelectronics and photonics and their applications,

-refereed research contributions reporting on original scientific or technological achievements,

-conference papers printed in normal issues as invited or contributed papers.

Authors of review papers are encouraged to write articles of relevance to a wide readership including both those established in this field of research and non-specialists working in related areas. Papers considered as “letters” are not published in OPELRE.

Opto-Electronics Review is published quarterly as a journal of the Association of Polish Electrical Engineers (SEP) and Polish Academy of Sciences (PAS) in cooperation with the Military University of Technology and under the auspices of the Polish Optoelectronics Committee of SEP.

Abstracting and Indexing:

Arianta

BazTech

EBSCO relevant databases

EBSCO Discovery Service

SCOPUS relevant databases

ProQuest relevant databases

Clarivate Analytics relevant databases

WangFang

additionally:

ProQuesta (Ex Libris, Ulrich, Summon)

Google Scholar

Policies and ethics:

The editors of the journal place particular emphasis on compliance with the following principles:

Ethical policy of Opto-Electronics Review

The ethical policy of Opto-Electronics Review follows the European Code of Conduct for Research Integrity and is also guided by the core practices and policies outlined by the Committee on Publication Ethics (COPE).

Authors must be honest in presenting their results and conclusions of their research. Research misconduct is harmful for knowledge.

Research results

Fabrication, falsification, or selective reporting of data with the intent to mislead or deceive is unethical, as is the theft of data or research results from others. The results of research should be recorded and maintained to allow for analysis and review. Following publication, the data should be retained for a reasonable period and made available upon request. Exceptions may be appropriate in certain circumstances to preserve privacy, to assure patent protection, or for similar reasons.

Authorship

All those who have made a significant contribution should be given chance to be cited as authors. Other individuals who have contributed to the work should be acknowledged. Articles should include a full list of the current institutional affiliations of all authors, both academic and corporate.

Competing interests

All authors, referees and editors must declare any conflicting or competing interests relating to a given article. Competing interests through their potential influence on behavior or content or perception may undermine the objectivity, integrity, or perceived value of publication.

Peer Review

We are committed to prompt evaluation and publication of fully accepted papers in Opto-Electronics Review’s publications. To maintain a high-quality publication, all submissions undergo a rigorous review process.

Characteristics of the peer review process are as follows:

• Simultaneous submissions of the same manuscript to different journals will not be tolerated.

• Manuscripts with contents outside the scope will not be considered for review.

• Opto-Electronics Review is a single-blind review journal.

• Papers will be refereed by at least 2 experts as suggested by the editorial board.

• In addition, Editors will have the option of seeking additional reviews when needed. Authors will be informed when Editors decide further review is required.

• All publication decisions are made by the journal’s Editor-in-Chief based on the referees’ reports. Authors of papers that are not accepted are notified promptly.

• All submitted manuscripts are treated as confidential documents. We expect reviewers to treat manuscripts as confidential material.

• Editors and reviewers involved in the review process should disclose conflicts of interest resulting from direct competitive, collaborative, or other relationships with any of the authors, and remove oneself from cases in which such conflicts preclude an objective evaluation. Privileged information or ideas that are obtained through peer review must not be used for competitive gain.

• A reviewer should be alert to potential ethical issues in the paper and should bring these to the attention of the editor, including any substantial similarity or overlap between the manuscript under consideration and any other published paper of which the reviewer has personal knowledge. Any statement, observation, derivation, or argument that had been previously reported should be accompanied by the relevant citation.

• Personal criticism is inappropriate.

Plagiarism

Reproducing text from other papers without properly crediting the source (plagiarism) or producing many papers with almost the same content by the same authors (self-plagiarism) is not acceptable. Submitting the same results to more than one journal concurrently is unethical. Exceptions are the review articles. Authors may not present results obtained by others as if they were their own. Authors should acknowledge the work of others used in their research and cite publications that have influenced the direction and course of their study.

Plagiarism is not tolerated. All manuscripts submitted to Opto-Electronics Review will be checked for plagiarism (copying text or results from other sources) and self-plagiarism (duplicating substantial parts of authors’ own published work without giving the appropriate references) using the CrossCheck database (iThenticate plagiarism checker).

Duplicate submission

Simultaneous submissions of the same manuscript to different journals will not be tolerated. The submitted article will be removed without consideration.

Corrections and retractions

All authors have an obligation to inform and cooperate with journal editors to provide prompt retractions or correction of errors in published works.

• The journal will issue retractions if:

• There is clear evidence that the findings are unreliable, either as a result of misconduct (e.g., data fabrication or honest error - miscalculation or experimental error);

• The findings have previously been published elsewhere without proper cross-referencing, permission or justification (i.e., cases of redundant publication);

• It constitutes plagiarism;

• It reports unethical research.

• The journal will issue errata, if:

• A small portion of an otherwise reliable publication proves to be misleading (especially because of honest error);

• The author list is incorrect.

Other forms of misconduct include failure to meet clear ethical and legal requirements such as misrepresentation of interests, breach of confidentiality, lack of informed consent and abuse of research subjects or materials. Misconduct also includes improper dealing with infringements, such as attempts to cover up misconduct and reprisals on whistleblowers.

The primary responsibility for handling research misconduct is in the hands of those who employ the researchers. If a possible misconduct is brought to our attention, we will seek advice from the referees and the Editorial Board. If there is the evidence, we will resolve the matter by appropriate corrections in the printed and online journal; by refusing to consider an author's future work and by contacting affected authors and editors of other journals.

Human and Animal Rights

If the work involves the use of human subjects, the author should ensure that the work described has been carried out in accordance with The Code of Ethics of the World Medical Association (Declaration of Helsinki) for experiments involving humans; Uniform Requirements for manuscripts submitted to Biomedical journals. Authors should include a statement in the manuscript that informed consent was obtained for experimentation with human subjects. The privacy rights of human subjects must always be observed.

All animal experiments should comply with the ARRIVE guidelines and should be carried out in accordance with the EU Directive 2010/63/EU for animal experiments, and the authors should clearly indicate in the manuscript that such guidelines have been followed.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji