Applied sciences

Metrology and Measurement Systems

Content

Metrology and Measurement Systems | 2012 | No 1

Download PDF Download RIS Download Bibtex

Abstract

The paper presents analyses of current research projects connected with explosive material sensors. Sensors are described assigned to X and γ radiation, optical radiation sensors, as well as detectors applied in gas chromatography, electrochemical and chemical sensors. Furthermore, neutron techniques and magnetic resonance devices were analyzed. Special attention was drawn to optoelectronic sensors of explosive devices.

Go to article

Authors and Affiliations

Zbigniew Bielecki
Tadeusz Stacewicz
Jacek Janucki
Adam Kawalec
Janusz Mikołajczyk
Norbert Pałka
Mateusz Pasternak
Tadeusz Pustelny
Jacek Wojtas
Download PDF Download RIS Download Bibtex

Abstract

The goal of the proposed computational model was to evaluate the dynamical properties of air gauges in order to exploit them in such industrial applications as in-process control, form deviation measurement, dynamical measurement. The model is based on Reynolds equations complemented by the k-ε turbulence model. The boundary conditions were set in different areas (axis of the chamber, side surfaces, inlet pipeline and outlet cross-section) as Dirichlet's and Neumann's ones. The TDMA method was applied and the efficiency of the calculations was increased due to the "line-by-line" procedure. The proposed model proved to be accurate and useful for non-stationary two-dimensional flow through the air gauge measuring chamber.

Go to article

Authors and Affiliations

Czeslaw Jermak
Andrzej Spyra
Miroslaw Rucki
Download PDF Download RIS Download Bibtex

Abstract

The article presents a new modification of the the least squares Prony method. The so-called variable-frequency Prony method can be a useful tool for estimating parameters of sinusoidal components, which, in the analyzed signal, are characterized by time-dependent frequencies. The authors propose use of the presented method for testing the quality of electric energy. It allows observation of phenomena which, when using traditional methods, are averaged in the analysis window. The proposed modification of least squares Prony method is based on introduction and specific selection of a frequency matrix. This matrix represents frequencies of estimated components and their variability in time.

Go to article

Authors and Affiliations

Janusz Mroczka
Jarosław Zygarlicki
Download PDF Download RIS Download Bibtex

Abstract

The work presented in the paper concerns a very important problem of searching for string alignments. The authors show that the problem of a genome pattern alignment could be interpreted and defined as a measuring task, where the distance between two (or more) patterns is investigated. The problem originates from modern computation biology. Hardware-based implementations have been driving out software solutions in the field recently. The complex programmable devices have become very commonly applied. The paper introduces a new, optimized approach based on the Smith-Waterman dynamic programming algorithm. The original algorithm is modified in order to simplify data-path processing and take advantage of the properties offered by FPGA devices. The results obtained with the proposed methodology allow to reduce the size of the functional block and radically speed up the processing time. This approach is very competitive compared with other related works.

Go to article

Authors and Affiliations

Andrzej Pułka
Adam Milik
Download PDF Download RIS Download Bibtex

Abstract

Current methods of fault diagnosis for the grounding grid using DC or AC are limited in accuracy and cannot be used to identify the locations of the faults. In this study, a new method of fault diagnosis for substation grounding grids is proposed using a square-wave. A frequency model of the grounding system is constructed by analyzing the frequency characteristics of the soil and the grounding conductors into which two different frequency square-wave sources are injected. By analyzing and comparing the corresponding information of the surface potentials of the output signals, the faults of the grounding grid can be diagnosed and located. Our method is verified by software simulation, scale model experiments and field experiments.

Go to article

Authors and Affiliations

Peng-He Zhang
Jun-Jia He
Dan-Dan Zhang
Lan-Min Wu
Download PDF Download RIS Download Bibtex

Abstract

The paper presents an analogue circuit testing method that engages the analysis of the time response to a non-periodic stimulus specialized for the verification of selected specifications. The decision about the current circuit diagnostic state depends on an amplitude spectrum decomposition of the time response measured during the test. A shape of the test excitation spectrum is optimized with the use of a differential evolution algorithm and it allows for achieving maximum fault coverage and the optimal conditions for fault isolation. Genotypes of the evolutionary system encode the amplitude spectrum of candidates for testing stimuli by means of rectangle frequency windows with amplitudes determined evolutionarily.

Go to article

Authors and Affiliations

Tomasz Golonek
Piotr Jantos
Jerzy Rutkowski
Download PDF Download RIS Download Bibtex

Abstract

This paper presents results of the study devoted to analysis of impact of upper extremities' momentum on the jump length and analysis of selected kinematic data changes during the standing long jump. Four young sportsmen participated in the initial study. They have performed standing long jump in two measuring conditions: with and without arms swinging. Motion was captured using a 3D opto-electronic camera system SMART (BTS) and selected kinematic data were evaluated using software packages and data processing: trajectory of body centre of gravity (COG), velocity of COG, maximal vertical distance of COG, take-off angle together with momentum of upper extremities were analyzed. The data were statistically evaluated using descriptive statistics and analysis of variance. Statistical significance of the kinematic data and jump length were analyzed using the Kruskal-Wallis test and post-hoc test (p<0.05) in Statistics toolbox of Matlab program. Statistically significant differences were assessed within intraindividual and intraclass comparison of data.

Go to article

Authors and Affiliations

Lenka Szerdiová
Dušan Simšik
Zlatica Dolná
Download PDF Download RIS Download Bibtex

Abstract

Passive radar does not have its own emitter. It uses so-called signals of opportunity emitted by non-cooperative illuminators. During the detection of reflected signals, a direct signal from a non-cooperative emitter is used as the reference signal. Detection of electromagnetic echoes is, in present day radars, performed by finding the maximum of the cross ambiguity function. This function is based on the multiplication of the received signal and the reference signal. Detection of echoes by means of a quadrature microwave phase discriminator QMPD was proposed in the work as an alternative solution for ambiguity function evaluation. This discriminator carries out vectorial summing of the received and the reference signals. The summing operations in QMPD are carried out with the aid of microwave elements and without the use of expensive digital signal processors. Definitions of the phase and phase difference of the so-called simple signals and noise signals were described. A proposal of a passive radar equipped with several independent quadrature microwave phase discriminators was presented. Ideas of algorithms of object detection and of the distance-to-object estimation designed for this radar have been also sketched.

Go to article

Authors and Affiliations

Adam Rutkowski
Download PDF Download RIS Download Bibtex

Abstract

The Multi-Tone (MT) signal with uniform amplitudes can be used for DAC testing. This paper shows an easier way to generate a MT signal using several impulse signals. The article also analyzes qualities of methods for testing the dynamic parameters of Digital to Analog Converters using an impulse signal. The MT, Damped Sine Wave (DSW) and Sinx/x (SINC) signals will be used as the source for these tests. The Effective Number of Bits (ENOB) and Signal to noise and distortion (SINAD) are evaluated in the frequency domain and they are modified using the Crest Factor (CF) correction and compared with the standard results of the Sine Wave FFT test. The first advantage of the test using an impulse signal is that you need fewer input parameters to create the band signal for testing the DAC. The second one is to reduce the testing time using a band signal in comparison with multiple tests using a single sine wave.

Go to article

Authors and Affiliations

Josef Vedral
Pavel Fexa
Download PDF Download RIS Download Bibtex

Abstract

The article presents results of the influence of the GMDH (Group Method of Data Handling) neural network input data preparation method on the results of predicting corrections for the Polish timescale UTC(PL). Prediction of corrections was carried out using two methods, time series analysis and regression. As appropriate to these methods, the input data was prepared based on two time series, ts1 and ts2. The implemented research concerned the designation of the prediction errors on certain days of the forecast and the influence of the quantity of data on the prediction error. The obtained results indicate that in the case of the GMDH neural network the best quality of forecasting for UTC(PL) can be obtained using the time-series analysis method. The prediction errors obtained did not exceed the value of ± 8 ns, which confirms the possibility of maintaining the Polish timescale at a high level of compliance with the UTC.

Go to article

Authors and Affiliations

Wiesław Miczulski
Łukasz Sobolewski
Download PDF Download RIS Download Bibtex

Abstract

LTCC-based pressure sensors are promising candidates for wet-wet applications in which the effect of the surrounding media on the sensor's characteristics is of key importance. The effect of humidity on the sensor's stability can be a problem, particularly in the case of capacitive sensors. A differential mode of operation can be a good solution, but manufacturing the appropriate sensing capacitors remains a major challenge. In the case of piezoresistive sensors the influence of humidity is less critical, but it still should be considered as an important parameter when designing sensors for low-pressure ranges. In this paper we discuss the stability of the sensors' offset characteristics, which was inspected closely using experimental and numerical analyses.

Go to article

Authors and Affiliations

Darko Belavič
Marina Zarnik
Download PDF Download RIS Download Bibtex

Abstract

The aim of the presented work was the development of a tracking algorithm for a stereoscopic camera setup equipped with an additional inertial sensor. The input of the algorithm consists of the image sequence, angular velocity and linear acceleration vectors measured by the inertial sensor. The main assumption of the project was fusion of data streams from both sources to obtain more accurate ego-motion estimation. An electronic module for recording the inertial sensor data was built. Inertial measurements allowed a coarse estimation of the image motion field that has reduced its search range by standard image-based methods. Continuous tracking of the camera motion has been achieved (including moments of image information loss). Results of the presented study are being implemented in a currently developed obstacle avoidance system for visually impaired pedestrians.

Go to article

Authors and Affiliations

Paweł Pełczyński
Bartosz Ostrowski
Dariusz Rzeszotarski
Download PDF Download RIS Download Bibtex

Abstract

Geometric deviations of free-form surfaces are attributed to many phenomena that occur during machining, both systematic (deterministic) and random in character. Measurements of free-form surfaces are performed with the use of numerically controlled CMMs on the basis of a CAD model, which results in obtaining coordinates of discrete measurement points. The spatial coordinates assigned at each measurement point include both a deterministic component and a random component at different proportions. The deterministic component of deviations is in fact the systematic component of processing errors, which is repetitive in nature. A CAD representation of deterministic geometric deviations might constitute the basis for completing a number of tasks connected with measurement and processing of free-form surfaces. The paper presents the results of testing a methodology of determining CAD models by estimating deterministic geometric deviations. The research was performed on simulated deviations superimposed on the CAD model of a nominal surface. Regression analysis, an iterative procedure, spatial statistics methods, and NURBS modelling were used for establishing the model.

Go to article

Authors and Affiliations

Małgorzata Poniatowska
Andrzej Werner
Download PDF Download RIS Download Bibtex

Abstract

The paper deals with an application-specific integrated circuit (ASIC) facilitating voltage conversion in thermoelectric energy harvesters. The chip is intended to be used to boost up the voltage coming from a thermoelectric module to a level that is required by electronic circuits constituting wireless sensor nodes. The designed charge pump does not need any external parts for its proper operation because all the capacitors, switches and oscillator are integrated on the common silicon die. The topography of the main functional blocks and post-layout simulations of the designed integrated circuit are shown in the article.

Go to article

Authors and Affiliations

Piotr Dziurdzia
Mariusz Mysiura
Adam Gołda

Instructions for authors



Sample article with Author guidelines



Author guidelines



Types of contributions

Metrology and Measurement Systems welcomes submissions of the following article types:

• invited special issue or review papers presenting the current stage of the knowledge within scope of the journal (about 20 edited pages, approximately 3000 characters each),
• research papers reporting high-quality original scientific or technological advancements (max. 12 pages),
• papers based on extended and updated contributions presented at scientific conferences (max. 12 pages),
• short notes, i.e. book reviews, conference reports, short news (max. 2 pages).


Manuscript preparation

General The text of a manuscript should be written in clear and concise English. The camera-ready format – with attached separate files containing illustrations, tables and photographs – is required. A cover letter with clear explanation of scientific novelty of the paper is strongly recommended. Papers based on extended and updated contributions presented at scientific conferences, or strongly related to previous authors’ works, must be accompanied with a cover letter file, which should explain in details changes made in the manuscript in comparison with the original conference paper and highlight the novelty in reference to other authors’ works.
The main text of a manuscript should be printed on an A4 page (with margins of 2.5 cm) using Times New Roman style with a font size of 12 pt; the paragraphs should start with the indentation of 5 mm, and titles should be written in bold. That text can be divided into sections (numbered 1, 2, …), first-order subsections (numbered 1.1., 1.2., …, written in italics), and – if needed – second-order subsections (numbered 1.1.1., 1.1.2., …, written same as first-order subsections). The only acceptable manuscript formats are in Microsoft Word (.doc, .docx).

The Editor encourages the Authors of submitted papers who are not English native speakers, to use a language service checking the language correctness not only with respect to grammar, but also in the way of presentation of research results accepted by renowned publishers, e.g. presented on the website of the European Association of Science Editors. The Editor encourages the Authors of submitted papers who are not English native speakers, to use a language service checking the language correctness not only with respect to grammar, but also in the way of presentation of research results accepted by renowned publishers, e.g. presented on the website of the European Association of Science Editors.


Figures
Figures (illustrations, photographs) and tables, provided in the camera-ready form suitable for reproduction (which may include reduction), should be additionally submitted (one per page), larger than the final size. While preparing figures we encourage to start with defining expected size and minimum font size that fit to all graphics in the manuscript – using the same style in all of your graphics visually improves the article. Final figure formats must be in one of the following: (vectors) .eps, .pdf, .ai or .cdr, and (bitmaps) .bmp, .gif, .tif or .jpg.
As far as plots, block diagrams, schematics etc. are concerned, we suggest to use one of vector formats to improve quality and scalability. Figures in vector formats must be saved using RGB colours and with fully white background (0% K). Hidden layers are unacceptable. Minimum line thickness printed in a single colour is 0.25 pt (0.09 mm), and 1 pt (0.36 mm) when using more colours. Typically we suggest 0.2-0.5 mm but in particular cases the range 0.1–1.0 mm will be accepted. Lines in plots should be distinguished not only by using different colours but also using different line types and markers, if needed.


Equation
All equations must be numbered consecutively throughout the text. Each equation should be preceded and followed by a 6-point spacing. Punctuate equations when they are part of a sentence. Equation numbers should be enclosed in parentheses. Equations should be prepared with the use of MathType or Microsoft Equation editors. The type size in the equation is the same as for the text. To make your equations more compact, you may use the appropriate mathematical symbols or expressions. The symbols used in an equation have to be defined before that equation or immediately after it. Use italics for variables (e.g. i, x, n), physical quantity symbol (e.g. voltage U, temperature T), letter pointers and general function symbols. Do not use italics for constants, indexes, minimum, maximum and trigonometric functions, mathematical operators, differentials, etc. To refer to the equation use “(1)”, not “Eq. (1)” or “equation (1)”, except at the beginning of a sentence where “Equation (1)” should be used. We recommend to use International System of Units SI i.e. metre-kilogram-second system of units. As a decimal separator dot should be used in the entire manuscript (text, figures, tables).


References
The paper has to be clearly positioned in the context of relevant literature in the field of measurements and instrumentation. Note that lack of references from the main field of Metrology and Measurement Systems interest may suggest that the content of manuscript does not exactly correspond to the scope of metrological journals. It may reduce possibility that a proposed paper will be read by audience society. In such a case our Editorial Board may suggest to send the manuscript to a more appropriate journal. Also note that the use of possibly up-to-date references may indicate importance of your work. Table below gives examples of some relevant and renewable journals related to widely understood metrology.


Journal

Publisher

ISSN

Metrologia

IOP Publishing

0026-1394

IEEE Transactions on Instrumentation and Measurement

IEEE

0018-9456

Measurement

Elsevier

0263-2241

Measurement Science and Technology

IOP Publishing

0957-0233

Metrology and Measurement Systems

PAS

0860-8229

Review of Scientific Instruments

IOP Publishing

0034-6748

IEEE Transactions on Industrial Electronics

IEEE

1557-9948

IET Science, Measurement & Technology

IET

1751-8822

Journal of Instrumentation

SISSA, IOP Publishing

1748-0221

Measurement Science Review

Walter de Gruyter

1335-8871

IEEE Instrumentation and Measurement Magazine

IEEE

1094-6969

Bulletin of the Polish Academy of Sciences: Technical Sciences

PAS

2300-1917

Opto-Electronics Review

PAS

1896-3757

IEEE Sensors Journal

IEEE

1558-1748

Sensors

MDPI

1424-8220




References should be inserted in the text in square brackets, i.e. [1]; their list, numbered in citation order, should appear at the end of the manuscript. The format of the references should follow the APA 7th edition formatting style, i.e.: for an journal paper – surname(s) and initial(s) of author(s), year in brackets, title of the paper, full journal name, volume, issue (in brackets) and page numbers. Put all author names unless there are more than 20. Otherwise, after the first 19 authors’ names, use an ellipsis in place of the remaining author names. Then, end with the final author’s name (do not place an ampersand before it).


Submission process
Manuscript should be submitted via the Internet Editorial System (IES) – an online submission and peer review system. In order to submit the manuscript via the IES, the authors (first-time users) must create an author account to obtain a user ID and password required to enter the system. The submission of the manuscript in a single file, i.e. “Article File” containing the complete manuscript (with all figures of high quality and tables embedded in the text), is preferred. All figures have to be uploaded in separate files. The generated PDF file has to be approved. The PDF file has lower quality of the embedded figures to limit its size only.
The submission of a manuscript means that its content has not been published previously, it is not under consideration for publication elsewhere, and that – if accepted – it will not be published elsewhere. The Author hereby grants the Polish Academy of Sciences (the Journal Owner) the license for commercial use of the article according to the Open Access License ( CC BY-NC-ND 4.0), which has to be signed before publication. The copyright form is available in the IES.
The Authors are urged to suggest 4 to 5 reviewers in their application (with names, affiliations and addresses) with whom the Editorial Board could co-operate while processing the paper. Proposed reviewers should be experts deeply involved in issues related to the subject matter of the paper and they are intended to come from different universities or research centres.
Each submitted manuscript is subject to a single-blind peer-review procedure, and the publication decision is based on the reviewers’ comments. If necessary, the authors may be invited to revise their manuscripts. On acceptance, manuscripts are subject to editorial amendment to exactly fit the journal style.
An essential criterion for the evaluation of submitted manuscripts is their potential impact on the research field, measured by the number of repeated quotations. Such papers are preferred at the evaluation and publication stages.
Proofs will be sent to the corresponding author by e-mail and should be returned within 48 hours from receipt. The publication in the journal is free of charge. A sample copy of the journal will be sent to the corresponding author free of charge. For colour pages the authors will be charged at the rate of 160 PLN or 80 EUR per page. The payment to the bank account of the main distributor (given in “Subscription Information”) must be completed before the date indicated by the Editorial Office.


Other information
It is possible to include supplementary files related to the article content, such as e.g. developed databases. These files can be then used by other researchers to compare their algorithms using the same input data. For more details about supplementary files please contact the Editorial Board: metrology@wat.edu.pl. The biographical statements, at the very end of the article, are not obligatory, however, they are kindly recommended. Each statement should include the author’s full name and brief personal history focused on areas of research and scientific achievements. The biographical statement may not exceed 100 words and should be written using Times New Roman style with a font size of 8 pt.
The publication of your article is a great achievement but then it needs to be further promoted to make it more visible to the research community. Responsibility for this task lies with the Authors and our Editorial Board. We guarantee free access to the article in the Journals PAN of the Polish Academy of Science, including articles in Early Access form (published just after acceptance decision), indexing in popular and renewable databases (e.g. Thomson Scientific Master Journal List, Elsevier’s Scopus, Google Scholar). Furthermore, selected articles are highlighted on the journal website and are reprinted for promotion at conferences and other events. The Authors can share the final form of the article on various social networks and research-sharing platforms, such as Twitter, Facebook, Linkedin, ResearchGate, Academia.edu, SciProfiles. They are also encouraged to update personal and institutional webpages by adding the title and a link of the article. Feel free also to share your work with your colleagues using any other methods that do not conflict with the CC BY-NC-ND 4.0 license.
For more detailed description about how to write a paper for the Metrology and Measurement Systems journal please look at the Author guidelines for manuscript preparation. We strongly recommend using this file as a template for manuscript preparation.


This page uses 'cookies'. Learn more