In this work, two thermal- and air-stable, hole transporting materials (HTM) in perovskite solar cells are analyzed. Those obtained and investigated materials were two polyazomethines: the first one with three thiophene rings and 3,3′-dimethoxybenzidine moieties (S9) and the second one with three thiophene rings and fluorene moieties (S7). Furthermore, presented polyazomethines were characterized by Fourier transform infrared spectroscopy (FTIR), UV–vis spectroscopy, atomic force microscopy (AFM) and thermogravimetric analysis (TGA) experiments. Both polyazomethines (S7 and S9) possessed good thermal stability with a 5% weight loss at 406 and 377°C, respectively. The conductivity of S7 was two orders of magnitude higher than for S9 polymer (2.7 × 10−8 S/cm, and 2.6 × 10−10 S/cm, respectively). Moreover, polyazomethine S9 exhibited 31 nm bathochromic shift of the absorption band maximum compared to S7.
Obtained perovskite was investigated by UV–vis and XRD. Electrical parameters of perovskite solar cells (PSC) were investigated at Standard Test Conditions (STC). It was found that both polyazomethines protect perovskite which is confirmed by ageing test where Voc did not decrease significantly for solar cells with HTM in contrast to solar cell without hole conductor, where Voc decrease was substantial. The best photoconversion efficiency (PCE = 6.9%), among two investigated in this work polyazomethines, was obtained for device with the following architectures FTO/TiO2/TiO2 + perovskite/S7/Au. Stability test proved the procreative effects of polyazomethines on perovskite absorber.
Photovoltaic (PV) technologies which play a role in PV market are divided into basic two types: wafer-based (1st generation PV) and thin-film cell (2nd generation PV). To the first category belong mainly crystalline silicon (c-Si) cells (both mono- and multi-crystalline). In 2015 around 90% of the solar market belonged to crystalline silicon. To the 2nd generation solar cells belongs thin film amorphous silicon (a-Si) or a combination of amorphous and microcrystalline silicon (a-Si/μc-Si), compound semiconductor cadmium telluride (CdTe), compound semiconductor made of copper, indium, gallium and selenium (CIS or CIGS) and III–V materials. The PV market for thin film technology is dominated by CdTe and CIGS solar cells. Thin film solar cells’ share for all thin film technologies was only 10% in 2015. New emerging technologies, called 3rd generation solar cells, remain the subject of extensive R&D studies but have not been used in the PV market, so far.
In this review the best laboratory 1st and 2nd generation solar cells that were recently achieved are described. The scheme of the layer structure and energy band diagrams will be analyzed in order to explain the boost of their efficiency with reference to the earlier standard designs.
The emergence of solar cells on flexible and bendable substrates has made the printing process a ubiquitous tool for the fabrication of these devices. The various printing techniques available now such as inkjet, screen and flexography offer cost- effectiveness, user-friendliness and suitability for mass production. While downscaling the fill factor and efficiency of organic solar cells. A multilayered structure, the combination of different printing techniques avails the variety of thickness and resolution required for each layer in the production of an organic solar cell. In this review article, we discuss the suitability of the inkjet and screen printing processes to produce organic solar cells. We also discuss various challenges involved in the fabrication of organic solar cells using these two techniques and the possible solutions for the same. We also provide an analogy that both processes share. Further, we consider future possibilities of combining these printing technologies to produce organic solar cells to improve device performance.
Single crystalline cesium doped ZnO nanorods with homogeneous size and shape were grown hydrothermally on ITO substrates that are presented in our previous work. According to the previous work, XRD analysis showed that cesium doped ZnO nanorods are wurtzite single crystals and are grown preferentially along the c-axis. Also, the electrical conductivity of doped ZnO showed higher values for the 1% cesium, which confirmed incorporation of the cesium dopant. Cesium doped ZnO nanorods are suitable candidates for applications in solar cells. So, in this research, we employed cesium doped ZnO nanorods with the different dopant concentration in inverted polymer solar cell. By comparing the effect of doped ZnO nanorods with diverse dopant concentration (0, 0.5, 1.0, 1.5 and 2%) on the performance of devices, 1.0% cesium doped ZnO was found as the most effective doping level among the selected doping concentrations. Also, using 1.0% cesium doped ZnO nanorods, Jsc of 8.21 mA/cm², Voc of 0.541V and Fill Factor of 63.01% were achieved, which led to power conversion efficiency of 2.80%.
This work presents a theoretical study for the distribution of nanocomposite structure of plasmonic thin-film solar cells through the absorber layers. It can be reduced the material consumption and the cost of solar cell. Adding nanometallic fillers in the absorber layer has been improved optical, electrical characteristics and efficiency of traditional thin film solar cells (ITO /CdS/PbS/Al and SnO2/CdS/CdTe/Cu) models that using sub micro absorber layer. Also, this paper explains analysis of J-V, P-V and external quantum efficiency characteristics for nanocomposites thin film solar cell performance. Also, this paper presents the effect of increasing the concentration of nanofillers on the absorption, energy band gap and electron-hole generation rate of absorber layers and the effect of volume fraction on the energy conversion efficiency, fill factor, space charge region of the nanocomposites solar cells.
The paper presents a dual-band plasmonic solar cell. The proposed unit structure gathers two layers, each layer consists of a silver nanoparticle deposited on a GaAs substrate and covered with an ITO layer, It reveals two discrete absorption bands in the infra-red part of the solar spectrum. Nanoparticle structures have been used for light-trapping to increase the absorption of plasmonic solar cells. By proper engineering of these structures, resonance frequencies and absorption coefficients can be controlled as it will be elucidated. The simulation results are achieved using CST Microwave Studio through the finite element method. The results indicate that this proposed dual-band plasmonic solar cell exhibits an absorption bandwidth, defined as the full width at half maximum, reaches 71 nm. Moreover, It can be noticed that by controlling the nanoparticle height above the GaAs substrate, the absorption peak can be increased to reach 0.77.
Dye-sensitized solar cells (DSSCs) were prepared using various food dyes. Food dyes are economically superior to organometallic dyes since they are nontoxic and inexpensive. The spectrophotometric evaluation of chosen food dyes in solution and on a TiO2 substrate show that the dyes form J-aggregation on the photoelectrode substrate. Oxidation of potential measurements for used food dyes ensured an energetically permissible and thermodynamically favorable charge transfer throughout the continuous cycle of a photo-electric conversion. The performance of dye-sensitized solar cells based on food dyes was studied. The results illustrate that the dye containing carboxylic acid and sulfonic acid as the acceptor group gave the maximum conversion efficiency 4.20%.
The paper presents the idea to improve the performance of thin film photovoltaic cells by a light capture enhancement through the introduction of down shifting energy converters. Luminescent down shifting layers convert high-energy photons (UV light) into low-energy ones (visible light), which are more efficient in a photovoltaic conversion. For this purpose, the application of a thin layer composed of zinc oxide (ZnO) nanoparticles deposited onto a thin film solar cell is proposed. The paper presents both experimental and theoretical results of this approach. Conducted investigations include an analysis of ZnO nanoparticle layers, deposited in two independent technology methods. The results showed that ZnO nanoparticles have a great potential of application as down converting layers and can be implemented to improve the efficiency of photovoltaic cells, especially in the field of thin film PV structures. The proposed new deposition method can potentially be used in some industrial photovoltaic applications.
Many variants of thin film technology are nowadays part of the photovoltaic market. The most popular are amorphous silicon, CIS (Copper Indium Selenide)/CIGS (Copper Indium Gallium Selenide)/CIGSS (Copper Indium Gallium Sulphur Selenide), and CdS/CdTe (Cadmium Sulphide/Cadmium-Telluride) cells. All mentioned types allow potentially for a flexible cell structure. Most emitter contacts are currently based on TCOs (Transparent Conductive Oxides), however, wider approach with alternative carbon nanoforms, silver nanolayers and polymer materials, called TCLs (Transparent Conductive Layers) are also in use. Authors decided to investigate influence of mechanical stresses on physical and electrical behaviour of these layers. Consequently, the aim of work is to determine the level and possible mechanisms of flexible a-Si cell parameters degradation due to a deterioration of transparent contact properties.
Results of the studies of optical properties of anti-reflective glasses with various texturization patterns, which were used as a coating for crystalline silicon solar cells, are presented. It was found that glass samples sorted by their optical transmittance demonstrated the same order as when sorted by their solar-cell short-circuit current enhancement parameter. The value of the latter depended on the parameters of texturization, such as the surface density of inclusions and their profile, and the depth of etching pits. A 2% relative increase of the solar cell efficiency was obtained for the best glass sample for null degree angle of incidence, proving enhanced light trapping properties of the studied glass.
Four dye-sensitized solar cell devices are designed and fabricated based on natural dyes extracted from Celosia Cristata, Saffron, Cynoglossum, and eggplant peel, as photosensitizers. The UV–vis technique has been served to determine maximum absorption of natural extract and pre-dyed photoanode. The Fourier transform infrared (FT-IR) was employed to cover the presence of functional groups. The cyclic voltammetry method has been employed to assess the possibility of charge transfer from dried natural dyes to the photoelectrode. The performance of natural-based dye-sensitized solar cells is determined subsequently. The highest power conversion efficiency was ca. 1.38%, which belonged to Celosia Cristata extract. The devices were examined for higher efficiencies, individually, co-sensitized arrangement and/or in tandem with each other.
In this study, glass frit was coated uniformly on the surface of Al particles instead of adding glass frit to Al powder by simple mixing to form a nano-layer. The influence of the glass-frit coating on the formation of the back-surface field and electrical characteristics of the resulting Al electrode were investigated. Microstructural observations indicated that the glass components were uniformly distributed and the back-surface field layer thickness was more uniform compared to the simply mixed sample. In addition, the sheet resistance was ˂10 mΩ/□, much lower than the 23 mΩ/□ of the simply mixed Al electrode.