Applied sciences

Archives of Environmental Protection

Content

Archives of Environmental Protection | 2009 | vol.35 | No 3 |

Download PDF Download RIS Download Bibtex

Abstract

Fungus Fnsarium solani, able to degrade methyl isobutyl ketone was isolated from the bed ofbiofilter cleaning exhausting gases from the cable plant "Załom" near Szczecin. This substance was used as the only source of carbon and energy. Confirmation and kinetic tests were performed in 25 cm- scrubbers filed with mineral medium which was inoculated with the fungus. Fusorium solani degraded MIBK at the rate up to 60 g·m3·h·1 and pollution loading up to 200 gm+h'. Degree of elimination ranged from 40 to 80% and decreased when culture pollution loading increased.
Go to article

Authors and Affiliations

Krystyna Przybulewska
Andrzej N. Wieczorek
Download PDF Download RIS Download Bibtex

Abstract

Hydrodynamic disintegration of the activated sludge and foam results in organic matter transfer from the solid phase to the liquid phase. Hydrodynamic disintegration caused an increase of COD value in activated sludge and foam of 220 mgdm3 and 609 mgdm3 - respectively, besides the degree of disintegration increases to 38% and 47%- respectively- alter 30 minutes of disintegration. Hydrodynamic cavitation affects positively the degree of disintegration and rate of biogas production. Also addition of a part of digested sludge containing adapted microorganisms resulted in acceleration of the anaerobic process. Addition of disintegrated foam (20% and 40% of volume) to the fermentation processes resulted in an improvement in biogas production by about 173% and 195% respectively - in comparison to activated sludge without disintegration (raw sludge) and 142% and 161 % respectively - in comparison to activated sludge with a part of digested sludge (80% raw sludge + 20% digested sludge).
Go to article

Authors and Affiliations

Alicja Machnicka
Klaudiusz Grubel
Jan Suschka
Download PDF Download RIS Download Bibtex

Abstract

The paper presents results of a study concerning ammonium and nitratc(V) fixation by soil irrigated with municipal wastcwatcrs ( 1 - 60 mm and 2 doses - 120 mm) and estimation or the possibility or using organic soil and grass-mixture for the wastewater treatment. It was found that the studied soil and the plant applied showed a very high capacity or binding ammonium ions (up to 96%), and lower in the case ofnitrates(V) (up to 71 %). It was also demonstrated that the single irrigation dose was better utilized compared to the double dose.
Go to article

Authors and Affiliations

Urszula Kotowska
Teresa Włodarczyk
Barbara Witkowska-Walczak
Cezary Sławiński
Download PDF Download RIS Download Bibtex

Abstract

Use ofvarious wastes containing iron or aluminium in wastewater treatment can be considered as an alternative method to expensive and commercial reagents. These wastes can be recycled thanks to this method, which is important from an environmental point of view. Washings generated during ground water treatment arc rather useless but they are one of waste iron sources. The article demonstrates a description of two ground water treatment plants supplying the city of Koszalin with drinking water. On the basis ofdata from the last four years, a balance of the annual amount of iron sludge formed as a result of backwashing filter beds in both plants was performed. The amount of waste iron exceeds 10 Mg Fe-year. Research on waste iron usage to remove orthophosphates from a model solution and real sludge liquor from sludge digestion showed that iron sludge from washings can be efficiently used in wastewater treatment technology.
Go to article

Authors and Affiliations

Krzysztof Piaskowski
Download PDF Download RIS Download Bibtex

Abstract

The aim of the study was fractionation of Zn, Cu, Ni, Pb in the bottom sediments of two small reservoirs: at Krempna on the Wisłoka River and at Zcslwicc on the Dlubnia River. The partitioning of metals for various fractions was performed with the use of Tessier's sequential chemical extraction method. All together five metal fractions were distinguished: exchangeable metals (fraction I), metals bound to carbonates (fraction II), metals bound to hydrate Fe-Mn oxides (fraction III), metals bound to organic matter (fraction IV), and metals bound to minerals (fraction V). The largest quantities of metals were bound with fraction V, the smallest occurred in the forms most easily available for living organisms, in faction I. Proportions ofZn, Ni and Pb in the exchangeable fraction were about 1%. The amounts of metals bound with fraction II were also relatively low, except lor Zn in bottom sediment at the Zeslawice Reservoir. In this bottom sediment the share of Zn bound to carbonates was 33%. Medium metal quantities were associated with hydrate Fe-Mn oxides (fraction III) and with organic matter (fraction IV). Relatively high proportion ofmetals in fraction V and trace amounts ofmetals in fraction I as well as alkaline and neutral reaction of the sediments may prove a potentially low hazard of the metal release in the case of chemical changes in the reservoirs.
Go to article

Authors and Affiliations

Marek Madeyski
Marek Tarnawski
Czesława Jasiewicz
Agnieszka Baran
Download PDF Download RIS Download Bibtex

Abstract

In result of a lew years' investigations or silting of small water reservoirs located in South Poland, intensity ofthe silting process as well as the granulometrie and chemical composition ofbottorn sediments were evaluated. The content of heavy metals i.e. copper, lead and cadmium was determined in samples collected in various parts or five small water reservoirs. The content of heavy metals was appraised according to the regulation of the Minister of Environment, according to the criteria or Polish Geological Institute, of Inspection lor Environmental Protection, of Institute of Soil Science and Plant Cultivation, and according to the Muller's method. The obtained results or determination of the examined heavy metals concentrations were compared with the values or reservoir and river sediment concentrations determined by other authors in Europe. Appraisal or sill quality, respectively to the adopted criteria, showed only an insignificant degree of pollution. Concentrations ofmicroclemcnts do not exceed the toxic concentrations for soils and environment bul may have a harmful influence on living organisms. Recording of changes or heavy metal pollution during many years' operation or small water reservoirs, considering changes occurring in the basins, requires continuation of investigations. It will enable to record changes or pollution during a longer period or operation or reservoirs, also against the background 01· changes occurring in river basins.
Go to article

Authors and Affiliations

Bogusłąw Michalec
Marek Tarnawski
Download PDF Download RIS Download Bibtex

Abstract

The paper contains a micobiological characteristic of sewage sludge composted in controlled conditions together with bio-wastes (straw, sawdust, bark). An experiment was carried out in which the composted material was mixed up in adequate weight proportion and placed in biorcactor chambers with a constant air flow. The composting process aimed at defining the development dynamics and the survival of pathogenic microorganisms in the sewage sludge composted with different additions in a cybernetic bioreactor. Samples of compost necessary for microbiological analyses were taken at the same time, in reference to the actual temperature value. Bacteriological studies were carried out on selected substrates by plate method determining the number of pathogenic bacteria from the species: Salmonella, Clostridium perfringens, as well as from Enterobacteriaccac family. In the experiments, the presence of living eggs or intestinal ATT pathogens was determined by floatation method, as well. Il was found that the sewage sludge used in composting process did not contain any Salmonella spp. bacteria or any living eggs of intestinal ATT pathogens. Composting process completely eliminated the number or bacteria from Enterobactcriaccae family, bul it did not contribute lo the elimination of Clostridium perfringens bacteria. On the basis of the obtained results, it was found that the elimination of the studied groups of microorganisms, in all studied composts took place with the increase of temperature. In the case or Enterobacteriaceae, it was found that their complete removal from the composted material took place in chamber K3, while in the remaining chambers, it followed 48 hours later. Elimination ofthe vegetative forms ofC!oslridium perfringens bacteria followed after 96 hours of composting, in all composts at the same time. The obtained composts met the sanitary norms according lo the regulations of the EC Commission No. I 85/2007 of February 20, 2007 which changed the regulation of WE No. 809/2003 and WE No. 810/2003 referring to the extension of the validity period of transitional means for composting plants and biogas producing plants according to the instruction orWE No. 1774/2002 of European Parliament and Council and according to the instruction of the Minister for Agriculture and Country Development (2004).
Go to article

Authors and Affiliations

Agnieszka Wolna-Maruwka
Jacek Dach
Download PDF Download RIS Download Bibtex

Abstract

The study makes an attempt to assess the impact of uncontrolled waste dumps on soil chemical and biochemical properties. Investigations were carried out on five waste disposal sites situated in the south-eastern outskirts or the city of Lublin. The samples of soils collected from the adjacent arabic land were used as reference material. In soils of four landfills, which were established relatively recently (lour to five years ago); several times higher activity of the examined enzymes (dehydrogcnascs, acid phosphatase, basic phosphatase, urcasc, protease) than in the soils from the adjacent cultivated land was determined. Opposite ti-ends were found in the case ofa waste dump established 20 years ago. The determined lack ofnegative influence or the examined waste dumps on the soil chemical and biochemical properties of the adjacent arabic land shows that the range or the contamination effect on the surrounding area was limited.
Go to article

Authors and Affiliations

Elżbieta Jolanta Bielińska
Agnieszka Mocek-Płóciniak
Download PDF Download RIS Download Bibtex

Abstract

In the first part of the paper the most often used processes in PRB technology are presented and described. These processes are: redox reactions, pH control, adsorption and biodegradation. They proceed in the reactive materials listed in the table. In the second part of the paper the procedure used in the assessment of possibilities of using PRB technology is presented. It was suggested to use preliminary assessment during the initial stage of the procedure, as it limits the range of the analysis to several most important factors. Moreover,. the conditions of using PRB were described. They can help to decide whether this technology should be accepted or not in the initial stage of the procedure. Such preliminary assessment of possibilities of using PRB was performed for two selected areas of dumping sites located in Upper Silesia, Poland. After accepting the possibilities of using this technology in their area, the types of reactive materials for effective treatment of groundwater were proposed for both of them.
Go to article

Authors and Affiliations

Tomasz Suponik
ORCID: ORCID
Marcin Lutyński
ORCID: ORCID
Download PDF Download RIS Download Bibtex

Abstract

The paper presents results or laboratory tests or solid-phase anaerobic biorerncdiation or soil contaminated with chlorinated pesticides. It was shown that using methanogcnic granular sludge as inoculum and lactate as electron donor, it is possible to remove 80% or y-HCH, 94% 01· methoxychlor and 93% or DDT against control sample, with DDD accumulation much less than stoichiometric. Pesticides removal was practically completed alter 4-6 weeks of incubation at 22°C. Additional application of nonionic surfactant Tween 80 resulted in about one and a half-fold decrease or residual concentrations or some corn pounds. It also enhanced DDT conversion to some extent, decreasing DDD accumulation and intensifying production of D8P, the terminal metabolite or DDT anaerobic degradation pathway. Use of methanol as electron donor produced effects quite similar to these obtained with lactate, however with reduced results scatter.
Go to article

Authors and Affiliations

Tomasz Baczyński
Download PDF Download RIS Download Bibtex

Abstract

The contents or Cd, Pb. Cu, Mn, Zn, Ni and Fe in different organs or Typha latifolia L., coming from six sites selected within Jezioro Wielkie (Leszczyńskie Lakeland in western Poland), were determined. Three groups or metals, cach with a different accumulation pattern within the plant were distinguished in this study. Pb, Zn and Cu were found to be the least mobile and shown the following accumulation scheme: roots> rhizomes> lower leave part> top leave part. 13y contrast, Mn, a metal which is both easily transported in plants and accumulated in green plant organs, exhibited the following accumulation scheme: roots> top leave part> lower leave part> rhizomes. Ni, Cd and re were accumulated by the cattail as follows: roots> rhizomes> top leaf part> lower leaf part. The fact that Tvpha tatifol io L. had the highest proportion 01· all the metals studied in its roots can suggest that some kind of protection barrier exists which prevents toxic compounds permeating from that part or this plant to its rhizomes and its aerial parts. The confirmation or this thesis requires some further research.
Go to article

Authors and Affiliations

Agnieszka Klink
Józef Krawczyk
Barbara Letachowicz
Magdalena Wisłocka

Instructions for authors

Archives of Environmental Protection
Instructions for Authors

Archives of Environmental Protection is a quarterly published jointly by the Institute of Environmental Engineering of the Polish Academy of Sciences and the Committee of Environmental Engineering of the Polish Academy of Sciences. Thanks to the cooperation with outstanding scientists from all over the world we are able to provide our readers with carefully selected, most interesting and most valuable texts, presenting the latest state of research in the field of engineering and environmental protection.

Scope
The Journal principally accepts for publication original research papers covering such topics as:
– Air quality, air pollution prevention and treatment;
– Wastewater treatment and utilization;
– Waste management;
– Hydrology and water quality, water treatment;
– Soil protection and remediation;
– Transformations and transport of organic/inorganic pollutants in the environment;
– Measurement techniques used in environmental engineering and monitoring;
– Other topics directly related to environmental engineering and environment protection.

The Journal accepts also authoritative and critical reviews of the current state of knowledge in the topic directly relating to the environment protection.

If unsure whether the article is within the scope of the Journal, please send an abstract via e-mail to: aep@ipispan.edu.pl

Preparation of the manuscript
The following are the requirements for manuscripts submitted for publication:
• The manuscript (with illustrations, tables, abstract and references) should not exceed 20 pages. In case the manuscript exceeds the required number of pages, we suggest contacting the Editor.
• The manuscript should be written in good English.
• The manuscript ought to be submitted in doc or docx format in three files:
– text.doc – file containing the entire text, without title, keywords, authors names and affiliations, and without tables and figures;
– figures.doc – file containing illustrations with legends;
– tables.doc – file containing tables with legends;
• The text should be prepared in A4 format, 2.5 cm margins, 1.5 spaced, preferably using Time New Roman font, 12 point. Thetext should be divided into sections and subsections according to general rules of manuscript editing. The proposed place of tables and figures insertion should be marked in the text.
• Legends in the figures should be concise and legible, using a proper font size so as to maintain their legibility after decreasing the font size. Please avoid using descriptions in figures, these should be used in legends or in the text of the article. Figures should be placed without the box. Legends should be placed under the figure and also without box.
• Tables should always be divided into columns. When there are many results presented in the table it should also be divided into lines.
• References should be cited in the text of an article by providing the name and publication year in brackets, e.g. (Nowak 2019). When a cited paper has two authors, both surnames connected with the word “and” should be provided, e.g. (Nowak and Kowalski 2019). When a cited paper has more than two author, surname of its first author, abbreviation ‘et al.’ and publication year should be provided, e.g. (Kowalski et al. 2019). When there are more than two publications cited in one place they should be divided with a coma, e.g. (Kowalski et al. 2019, Nowak 2019, Nowak and Kowalski 2019). Internet sources should be cited like other texts – providing the name and publication year in brackets.
• The Authors should avoid extensive citations. The number of literature references must not exceed 30 including a maximum of 6 own papers. Only in review articles the number of literature references can exceed 30.
• References should be listed at the end of the article ordered alphabetically by surname of the first author. References should be made according to the following rules:

1. Journal:
Surnames and initials. (publication year). Title of the article, Journal Name, volume, number, pages, DOI.
For example:

Nowak, S.W., Smith, A.J. & Taylor, K.T. (2019). Title of the article, Archives of Environmental Protection, 10, 2, pp. 93–98. DOI: 10.24425/aep.2019.126330

If the article has been assigned DOI, it should be provided and linked with the website on which it is made available.

2. Book:
Surnames and initials. (publication year). Title, Publisher, Place and publishing year.
For example:

Kraszewski, J. & Kinecki, K. (2019). Title of book, Work & Studies, Zabrze 2019.

3. Edited book:

Surnames and initials of text authors. (publishing year). Title of cited chapter, in: Title of the book, Surnames and
initials of editor(s). (Ed.)/(Eds.). Publisher, Place, pages.
For example:

Reynor, J. & Taylor, K.T. (2019). Title of chapter, in: Title of the cited book, Kaźmierski, I. & Jasiński, C. (Eds.). Work & Studies, Zabrze, pp. 145–189.

4. Internet sources:
Surnames and initials or the name of the institution which published the text. (publication year). Title, (website address (accessed on)).
For example:

Kowalski, M. (2018). Title, (http://www.krakow.pios.gov.pl/publikacje/2009/ (03.12.2018)).

5. Patents:

Orszulik, E. (2009). Palenisko fluidalne, Patent polski: nr PL20070383311 20070910 z 16 marca 2009.
Smith, I.M. (1988). U.S. Patent No. 123,445. Washington, D.C.: U.S. Patent and Trademark Office.

6. Materials published in language other than English:
Titles of cited materials should be translated into English. Information of the language the materials were published in should be provided at the end.
For example:

Nowak, S.W. & Taylor, K.T. (2019). Title of article, Journal Name, 10, 2, pp. 93–98. DOI: 10.24425/aep.2019.126330. (in Polish)

Not more than 30 references should be cited in the original research paper.


Submission of the manuscript
By submitting the manuscript Author(s) warrant(s) that the article has not been previously published and is not under consideration by another journal. Authors claim responsibility and liability for the submitted article.
The article is freely available and distributed under the terms of Creative Commons Attribution-ShareAlike 4.0 International Public License (CC BY SA 4.0, https://creativecommons.org/licenses/by-sa/4.0/legalcode), which permits use, distribution and reproduction in any medium provided the article is properly cited, is not used for commercial purposes and no modification or adaptation are made.


© 2021. The Author(s). This is an open-access article distributed under the terms of the Creative Commons Attribution-ShareAlike 4.0 International Public License (CC BY SA 4.0, https://creativecommons.org/licenses/by-sa/4.0/legalcode), which permits use, distribution, and reproduction in any medium, provided that the article is properly cited, the use is non-commercial, and no modifications or adaptations are made


The manuscripts should be submitted on-line using the Editorial System available at http://www.editorialsystem.com/aep. Authors are asked to propose at least 4 potential reviewers, including 2 from Poland, together with their e-mail addresses. The journal does not have article processing charges (APCs) nor article submission charges.

Review Process
All the submitted articles are assessed by the Editorial Board. If positively assessed by at least two editors, Editor in Chief, along with department editors selects two independent reviewers from recognized authorities in the discipline.
Review process usually lasts from 1 to 4 months.
Reviewers have access to PUBLONS platform which integrates into Bentus Editorial System and enables adding reviews to their personal profile.
After completion of the review process Authors are informed of the results and – if both reviews are positive – asked to correct the text according to reviewers’ comments. Next, the revised work is verified by the editorial staff for factual and editorial content.

Acceptance of the manuscript

The manuscript is accepted for publication on grounds of the opinions of independent reviewers and approval of Editorial Board. Authors are informed about the decision and also asked to pay processing charges and to send completed declaration of the transfer of copyright to the editorial office.

Proofreading and Author Correction
All articles published in the Archives of Environmental Protection go through professional proofreading process. If there are too many language errors that prevent understanding of the text, the article is sent back to Authors with a request to correct the indicated fragments or – in extreme cases – to re-translate the text.
After proofreading the manuscript is prepared for publishing. The final stage of the publishing process is Author correction. Authors receive a page proof copy of the article with a request to make final corrections.

Article publication charges
The publication fee of an article in the Journal is:
25 EUR/100 zł per page (black and white or in gray scale),
35 EUR/130 zł per page (color).

Payments in Polish zlotys
Bank BGK
Account no.: 20 1130 1091 0003 9111 7820 0001

Payments in Euros
Bank BGK
Account no.: 20 1130 1091 0003 9111 7820 0001
IBAN: PL 20 1130 1091 0003 9111 7820 0001
SWIFT: GOSKPLPW

Authors are kindly requested to inform the editorial office of making payment for the publication, as well as to send all necessary data for issuing an invoice.
 

Additional info

Abstracting & Indexing

Archives of Environmental Protection is covered by the following services:

AGRICOLA (National Agricultural Library)

AGRIS

Arianta

Baidu Scholar

BazTech

CABI (over 50 subsections)

Chemical Abstracts Service (CAS) - CAplus

Chemical Abstracts Service (CAS) - SciFinder

CNKI Scholar (China National Knowledge Infrastructure)

CNPIEC

Dimensions

DOAJ (Directory of Open Access Journals)

EBSCO (relevant databases)

EBSCO Discovery Service

Engineering Village

FSTA - Food Science & Technology Abstracts

Genamics JournalSeek

GeoArchive

GeoRef

Google Scholar

Index Copernicus

Inspec

Japan Science and Technology Agency (JST)

J-Gate

Journal Citation Reports/Science Edition

JournalTOCs

KESLI-NDSL (Korean National Discovery for Science Leaders)

Microsoft Academic

Naviga (Softweco)

Primo Central (ExLibris)

ProQuest (relevant databases)

Publons

ReadCube

Reaxys

SCOPUS

Sherpa/RoMEO

Summon (Serials Solutions/ProQuest)

TDNet

TEMA Technik und Management

Ulrich's Periodicals Directory/ulrichsweb

WanFang Data

Web of Science - Biological Abstracts

Web of Science - BIOSIS Previews

Web of Science - Science Citation Index Expanded

WorldCat (OCLC)

This page uses 'cookies'. Learn more