Nauki Techniczne

Archives of Environmental Protection


Archives of Environmental Protection | 2015 | vol. 41 | No 1 |


Cyanobacterial blooms occur frequently in artificial lakes, especially in water reservoirs with small retention exposition to anthropopressure. The abundant occurrence of cyanobacteria is accompanied by danger of oxygen imbalance in the aquatic environment and the secretion of toxins that are possible threat to human health and life. Cyanobacterial cell growth depends on a number of physical (temperature, light exposure), chemical (pH, concentration of compounds containing nitrogen and phosphorus) and biological (the presence of other organisms) factors. This paper presents the results of the analysis of water from reservoirs located in southern Wielkopolska region (Pokrzywnica-Szałe, Gołuchów and Piaski-Szczygliczka). Some important physico-chemical parameters of water samples taken from investigated reservoirs as well as cyanotoxins concentration were determined. Furthermore, the cyanobacterial species were identified. There was also an attempt made to correlate the water parameters with the cyanobacteria development and cyanotoxins production. On the basis of the results obtained in the analyzed season, it can be concluded that water from Pokrzywnica and Gołuchów reservoirs was rich in nutrients, hence the intense cyanobacterial blooms and cyanotoxins in water were observed

Przejdź do artykułu

Autorzy i Afiliacje

Dominik Szczukocki
Radosław Dałkowski
Barbara Krawczyk
Renata Juszczak
Luiza Kubisiak-Banaszkiewicz
Barbara Olejniczak
Grzegorz Andrijewski


The selection of bioremediation techniques is important for purification of contaminated soil for agricultural use. Studies on soil contaminated with petroleum substances have indicated that the applied method of remediation has a bigger impact on the development of oat seedlings than the level of contamination. A yeast inoculum appeared to be a technique which was the friendliest to vegetation of oat

Przejdź do artykułu

Autorzy i Afiliacje

Małgorzata Pawełczak
Barbara Dawidowska-Marynowicz
Bartosz Oszywa
Magdalena Koszałkowska
Łukasz Kręcidło
Teresa Krzyśko-Łupicka


Improving the effects of hydrolysis on waste activated sludge (WAS) prior to anaerobic digestion is of primary importance. Several technologies have been developed and partially implemented in practice. In this paper, perhaps the simplest of these methods, alkaline solubilization, has been investigated and the results of hydrolysis are presented. An increase to only pH 8 can distinctively increase the soluble chemical oxygen demand (SCOD), and produce an anaerobic condition effect favorable to volatile fatty acids (VFA) production. Further increases of pH, up to pH 10, leads to further improvements in hydrolysis effects. It is suggested that an increase to pH 9 is sufficient and feasible for technical operations, given the use of moderate anti-corrosive construction material. This recommendation is also made having taken in consideration the option of using hydrodynamic disintegration after the initial WAS hydrolysis process. This paper presents the effects of following alkaline solubilization with hydrodynamic disintegration on SCOD

Przejdź do artykułu

Autorzy i Afiliacje

Jan Suschka
Eligiusz Kowalski
Jerzy Mazierski
Klaudiusz Grübel


Heavy metal (As, Mn, Ni, Sn, Ti) concentrations were determined in soil and plant samples collected in different areas of the railway junction Iława Główna, Poland. Soil and plant samples were collected in four functional parts of the junction, i.e. the loading ramp, main track within the platform area, rolling stock cleaning bay and the railway siding. Four plant species occurring in relatively higher abundance were selected for heavy metals analysis, although in the loading ramp and platform areas only one species could be collected in the amount which makes chemical analysis possible. The selected species included three perennials (Daucus carota, Pastinaca sativa and Taraxacum officinale) and one annual plant (Sonchus oleraceus).

The entire area of the railway junction showed elevated concentrations of heavy metals when compared to the control level. It was most pronounced for the platform area and railway siding. The concentration of arsenic, manganese and nickel in plants growing in these parts of the junction exceeded the toxic level. The highest contamination of soil and plants found in the platform area suggested advanced emission process of the analyzed metals from wheel and track abrasion. Literature review showed that the concentration of the investigated metals in soil was generally higher than that found in centers of cities and along traffic roads proving that the railway is an important linear source of soil contamination

Przejdź do artykułu

Autorzy i Afiliacje

Tomasz Staszewski
Małgorzata Malawska
Barbara Studnik-Wójcikowska
Halina Galera
Bogusław Wiłkomirski


This study was undertaken to determine the effectiveness of biosurfactants - saponin, tannin and rhamnolipids JBR 515 and 425, for the removal of cadmium, zinc and copper from activated sludge immobilized in 1.5% sodium alginate with 0.5% polyvinyl alcohol. We also established the impact of pH value on biosorbent regeneration with the analyzed biosurfactants and determined the critical micelle concentration (CMC) in solutions containing the biosorbent and biosurfactant and in exact samples with heavy metals. Saponin exhibited the highest effectiveness of metals leaching at pH 1-5, and rhamnosides at pH 5-6. In addition, the study demonstrated a significant effect of the ratio of biosorbent mass to washing agent volume (m/V) on the effectiveness of metals leaching. Of the biosurfactants analyzed, saponin was ca. 100% effective in leaching zinc and copper. The effectiveness of the other biosurfactants was lower and depended on the metal being leached

Przejdź do artykułu

Autorzy i Afiliacje

Małgorzata Kuczajowska-Zadrożna
Urszula Filipkowska
Tomasz Jóźwiak


The objective of this paper is to evaluate the self- healing properties of a commercially-available geosynthetic clay liner (GCL) using flexible-wall permeameter. The GCLs are produced by the same factory, but the contents of bentonite are different. Also the hydraulic conductivities (HC) of GCLs with no defect are different. In this study, specimens were completely saturated under the backpressure of 20 kPa before the test. Permeability tests were performed on GCL specimens with penetrating flaw and also on specimens permeated with distilled water and CaCl2 solutions. The test results were presented and discussed. Experimental results showed that the GCL with penetrating flaw did not exhibit complete self-healing in the case of flaw. After 120 days, the hydraulic conductivity increased by approximately an order of magnitude. In addition, CaCl2 solutions had a significant influence on the hydraulic conductivity. The research findings might be of interest to researchers and engineers who design liners for landfills and other liquid containment facilities

Przejdź do artykułu

Autorzy i Afiliacje

Guang-Wei Zhang
Hu-Yuan Zhang
Jin-Fang Wang
Lang Zhou
Ping Liu
Xiao Jiang


A laboratory study was performed to study the effects of various operating factors, viz. adsorbent dose, contact time, solution pH, stirring speed, initial concentration and temperature on the adsorption of triphenyltin chloride (TPT) onto coal fly ash supported nZnO (CFAZ). The adsorption capacity increases with increase in the adsorbent amount, contact time, pH, stirring speed and initial TPT concentration, and decrease with increase in the solution temperature. The adsorption data have been analyzed by Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-R) adsorption models to determine the mechanistic parameters associated with the adsorption process while the kinetic data were analyzed by pseudo first-order, pseudo second-order, Elovich, fractional power and intraparticle diffusivity kinetic models. The thermodynamic parameters of the process were also determined. The results of this study show that 0.5 g of CFAZ was able to remove up to 99.60% of TPT from contaminated natural seawater at 60 min contact time, stirring speed of 200 rpm and at a pH of 8. It was also found that the equilibrium and kinetic data fitted better to Freundlich and pseudo second-order models, respectively. It can therefore be concluded that CFAZ can be effectively used for shipyard process wastewater treatment

Przejdź do artykułu

Autorzy i Afiliacje

Olushola S. Ayanda
Olalekan S. Fatoki
Folahan A. Adekola
Bhekumusa J. Ximba
Olatunbosun S. Akinsoji
Leslie F. Petrik


The aim of the research conducted in a 2-year pot experiment in an unheated plastic tunnel was to determine suitability of Miscanthus × giganteus for phytoextraction of nickel from soil as well as to assess tolerance of this species on increasing concentrations of this metal in soil. Pots were filled with mineral soil (sand) and a mixture of soil with high-moor peat and three levels of nickel were introduced, i.e. 75 mg dm-3, 150 mg dm-3 and 600 mg dm-3 and the control combinations used substrates without the addition of nickel. Nickel was introduced only in the first year of the experiment in the form of nickel sulfate (NiSO4 · 6H2O). Miscanthus × giganteus accumulated a considerable amount of nickel in biomass. Miscanthus × giganteus growing in contaminated mineral soil turned out to be a species tolerant to high nickel concentrations

Przejdź do artykułu

Autorzy i Afiliacje

Maciej Bosiacki


The paper presents characterisation of the eco-chemical condition and potential threats to soils of goose farms on the basis of recent monitoring of a 15-year measuring cycle. It was demonstrated that the observed soil enzymatic inactivation progressing with years of investigations on the examined farms was significantly associated with a very high content of mineral nitrogen and available forms of phosphorus. A distinct tendency towards increased content of heavy metals in soils derived from these farms as well as in their direct neighbourhood observed with the passage of time poses a serious hazard to the environment

Przejdź do artykułu

Autorzy i Afiliacje

Elżbieta Jolanta Bielińska
Agnieszka Mocek-Płóciniak


A catalytic combustion of organic admixtures of air belongs to the basic technologies of gas purification. A macrokinetics of admixtures combustion over the porous catalysts was described. The theoretical approach is in agreement with standard description of macrokinetics of the catalytic processes. The relationship between the fundamental magnitudes: observed process rate r*, reaction rate r in the kinetic zone, and a coefficient of the surface utilization η in the form r*= r · η have been described. These magnitudes combines the Thiele module φ. A kinetics equation for the isothermal and non-isothermal conditions was provided. The influence of mass and heat transfer in the catalyst grain on the course of the process was described by means of the surface utilization coefficient η. An equation describing this coefficient for both isothermal and non-isothermal conditions was given. The second part of this work concerns the application of theory. When the composition of purified gas is continuously varied, a quantitative approach is rather impossible. The theory was used for the qualitative analysis of process on the basis of the experimental results. A fulfillment of the first-order kinetics means that the degree of admixtures conversion does not depend on their initial concentrations. A non-isothermicity of the catalyst grain is expressed in such a way that the process rate observed over the large porous grains of the catalyst can be higher than the reaction rate in the kinetic zone. A temperature deference between the catalyst grains and flowing gas causes that the reactor can be stably operated at varied concentrations of admixtures and temperature over a relatively wide range. It was also demonstrated that the flammable admixtures may advantageously influence the conversion of hardly combustible admixtures

Przejdź do artykułu

Autorzy i Afiliacje

Jerzy Straszko
Wiesław Parus
Wojciech Paterkowski

Instrukcja dla autorów

Archives of Environmental Protection

Instructions for Authors

Archives of Environmental Protection is a quarterly published jointly by the Institute of Environmental Engineering of the Polish Academy of Sciences and the Committee of Environmental Engineering of the Polish Academy of Sciences. Thanks to the cooperation with outstanding scientists from all over the world we are able to provide our readers with carefully selected, most interesting and most valuable texts, presenting the latest state of research in the field of engineering and environmental protection.

The Journal principally accepts for publication original research papers covering such topics as:
- Air quality, air pollution prevention and treatment;
- Wastewater treatment technologies and processing of sewage sludge;
- Technologies in waste management in the field of neutralization / recovery / closed circulation;
- Hydrology and water quality, water treatment;
- Soil protection and remediation;
- Transformations and transport of organic/inorganic pollutants in the environment;
- Measurement techniques used in environmental engineering and monitoring;
- Other topics directly related to environmental engineering and environment protection.

The Journal accepts also authoritative and critical reviews of the current state of knowledge in the topic directly relating to the environment protection.

If unsure whether the article is within the scope of the Journal, please send an abstract via e-mail to:

Preparation of the manuscript
The following are the requirements for manuscripts submitted for publication:
* The manuscript (with illustrations, tables, abstract and references) should not exceed 20 pages. In case the manuscript exceeds the required number of pages, we suggest contacting the Editor.
* The manuscript should be written in good English.
* The manuscript ought to be submitted in doc or docx format in three files:
– text.doc – file containing the entire text, without title, keywords, authors names and affiliations, and without tables and figures;
– figures.doc
– file containing illustrations with legends;
– tables.doc
– file containing tables with legends;

*The text should be prepared in A4 format, 2.5 cm margins, 1.5 spaced, preferably using Time New Roman font, 12 point. The text should be divided into sections and subsections according to general rules of manuscript editing. The proposed place of tables and figures insertion should be marked in the text.
* Legends in the figures should be concise and legible, using a proper font size so as to maintain their legibility after decreasing the font size. Please avoid using descriptions in figures, these should be used in legends or in the text of the article. Figures should be placed without the box. Legends should be placed under the figure and also without box.
* Tables should always be divided into columns. When there are many results presented in the table it should also be divided into lines.
* References should be cited in the text of an article by providing the name and publication year in brackets, e.g. (Nowak 2019). When a cited paper has two authors, both surnames connected with the word “and” should be provided, e.g. (Nowak and Kowalski 2019). When a cited paper has more than two authors, surname of its first author, abbreviation ‘et al.’ and publication year should be provided, e.g. (Kowalski et al. 2019). When there are more than two publications cited in one place they should be divided with a coma, e.g. (Kowalski et al. 2019, Nowak 2019, Nowak and Kowalski 2019). Internet sources should be cited like other texts - providing the name and publication year in brackets.
* The Authors should avoid extensive citations. The number of literature references must not exceed 30 including a maximum of 6 own papers. Only in review articles the number of literature references can exceed 30.
* References should be listed at the end of the article ordered alphabetically by surname of the first author. References should be made according to the following rules:

1. Journal:
Surnames and initials. (publication year). Title of the article, Journal Name, volume, number, pages, DOI.
For example:

Nowak, S.W., Smith, A.J. & Taylor, K.T. (2019). Title of the article, Archives of Environmental Protection, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330

If the article has been assigned DOI, it should be provided and linked with the website on which it is made available.

2. Book:
Surnames and initials. (publication year). Title, Publisher, Place and publishing year.
For example:

Kraszewski, J. & Kinecki, K. (2019). Title of book, Work & Sudies, Zabrze 2019.

3. Edited book:
Surnames and initials of text authors. (publishing year). Title of cited chapter, in: Title of the book, Surnames and initials of editor(s). (Ed.)/(Eds.). Publisher, Place, pages.
For example:
Reynor, J. & Taylor, K.T. (2019). Title of chapter, in: Title of the cited book, Kaźmierski, I. & Jasiński, C. (Eds.). Work & Studies, Zabrze, pp. 145–189.

4. Internet sources:
Surnames and initials or the name of the institution which published the text. (publication year). Title, (website address (accessed on)).
For example:
Kowalski, M. (2018). Title, ( (03.12.2018)).

5. Patents:
Orszulik, E. (2009). Palenisko fluidalne, Patent polski: nr PL20070383311 20070910 z 16 marca 2009. Smith, I.M. (1988). U.S. Patent No. 123,445. Washington, D.C.: U.S. Patent and Trademark Office.

6. Materials published in language other than English:
Titles of cited materials should be translated into English. Information of the language the materials were published in should be provided at the end.

For example:
Nowak, S.W. & Taylor, K.T. (2019). Title of article, Journal Name, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330. (in Polish)

Not more than 30 references should be cited in the original research paper.

Submission of the manuscript
By submitting the manuscript Author(s) warrant(s) that the article has not been previously published and is not under consideration by another journal. Authors claim responsibility and liability for the submitted article. The article is freely available and distributed under the terms of Creative Commons Attribution-ShareAlike 4.0 International Public License (CC BY SA 4.0, https: //, which permits use, distribution and reproduction in any medium provided the article is properly cited, is not used for commercial purposes and no modification or adaptation are made.

© 2021. The Author(s). This is an open-access article distributed under the terms of the Creative Commons Attribution-ShareAlike 4.0 International Public License (CC BY SA 4.0, https://, which permits use, distribution, and reproduction in any medium, provided that the article is properly cited, the use is non-commercial, and no modifications or adaptations are made

The manuscripts should be submitted on-line using the Editorial System available at Authors are asked to propose at least 4 potential reviewers, including 2 from Poland, together with their e-mail addresses. The journal does not have article processing charges (APCs) nor article submission charges.

Review Process
All the submitted articles are assessed by the Editorial Board. If positively assessed by at least two editors, Editor in Chief, along with department editors selects two independent reviewers from recognized authorities in the discipline. Reviewers receive a text of the article (without personal data of Authors) and review forms applicable in the journal. Review process usually lasts from 1 to 4 months. Reviewers have access to PUBLONS platform which integrates into Bentus Editorial System and enables adding reviews to their personal profile. After completion of the review process Authors are informed of the results and - if both reviews are positive - asked to correct the text according to reviewers’ comments. Next, the revised work is verified by the editorial staff for factual and editorial content.

Acceptance of the manuscript
The manuscript is accepted for publication on grounds of the opinions of independent reviewers and approval of Editorial Board. Authors are informed about the decision and also asked to pay processing charges and to send completed declaration of the transfer of copyright to the editorial office.

Proofreading and Author Correction
All articles published in the Archives of Environmental Protection go through professional proofreading process. If there are too many language errors that prevent understanding of the text, the article is sent back to Authors with a request to correct the indicated fragments or - in extreme cases – to re-translate the text. After proofreading the manuscript is prepared for publishing. The final stage of the publishing process is Author correction. Authors receive a page proof copy of the article with a request to make final corrections.

Article publication charges
The publication fee of an article in the Journal is:
* 20 EUR/80 zł per page (black and white or in gray scale),
* 30 EUR/120 zł per page (color).

Payments in Polish zlotys
Bank BGK
Account no.: 20 1130 1091 0003 9111 7820 0001

Payments in Euros
Bank BGK
Account no.: 20 1130 1091 0003 9111 7820 0001
IBAN: PL 20 1130 1091 0003 9111 7820 0001

Authors are kindly requested to inform the editorial office of making payment for the publication, as well as to send all necessary data for issuing an invoice.

Dodatkowe informacje

Abstracting & Indexing

Archives of Environmental Protection is covered by the following services:

AGRICOLA (National Agricultural Library)



Baidu Scholar


CABI (over 50 subsections)

Chemical Abstracts Service (CAS) - CAplus

Chemical Abstracts Service (CAS) - SciFinder

CNKI Scholar (China National Knowledge Infrastructure)



DOAJ (Directory of Open Access Journals)

EBSCO (relevant databases)

EBSCO Discovery Service

Engineering Village

FSTA - Food Science & Technology Abstracts

Genamics JournalSeek



Google Scholar

Index Copernicus


Japan Science and Technology Agency (JST)


Journal Citation Reports/Science Edition


KESLI-NDSL (Korean National Discovery for Science Leaders)

Microsoft Academic

Naviga (Softweco)

Primo Central (ExLibris)

ProQuest (relevant databases)






Summon (Serials Solutions/ProQuest)


TEMA Technik und Management

Ulrich's Periodicals Directory/ulrichsweb

WanFang Data

Web of Science - Biological Abstracts

Web of Science - BIOSIS Previews

Web of Science - Science Citation Index Expanded

WorldCat (OCLC)

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji