Nauki Techniczne

Archives of Civil Engineering

Zawartość

Archives of Civil Engineering | 2018 | Vol. 64 | No 4/II

Abstrakt

Civil engineering is one of the many fields of occurrences of uncertain parameters. The present paper in an attempt to present and describe the most common methods used for inclusions of uncertain parameters . These methods can be applied in the area of civil engineering as well as for a larger domain. Definitions and short explanations of methods based on probability, interval analysis, fuzzy sets, and convex sets are presented. Selected advantages, disadvantages, and the most common fields of implementation are indicated.

An example of a cantilever beam presented in this paper shows the main differences between the methods. Results of the performed analysis indicate that the use of convex sets allows us to obtain an accuracy of results similar to stochastic models. At the same time, the computational speed characteristic for interval methods is maintained.

Przejdź do artykułu

Autorzy i Afiliacje

J. Pełczyński

Abstrakt

Rubberized concrete is made up of scrap tyre rubbers where the fine aggregate is partially replaced by it, as the waste rubber is being a threat to the environment. It is estimated that only 4% of the waste tyre is used in the application of civil engineering and also there is shortage of fine aggregates. The primary objective of this study is to investigate the preliminary concrete properties of M25 and M30 concretes. The fine aggregate is replaced by pre-treated crumb rubber with 10, 15 and 20 % of total weight. Various tests are conducted on the rubberized concrete specimens such as compressive strength, split tensile strength, flexural strength and slump test. The investigation is carried out to determine the impact load behavior of hybrid rubberized composite slabs. In addition 0%, 1%, 1.5%, and 2% of replacement of rubber fibers for total weight of coarse aggregate is also made. The specimen of size 300 mm x 300 mm x 50 mm thickness is subjected to drop hammer test to find its performance against the impact loads. The number of blows for the first crack and complete failure of slab was found and the characteristics were studied.

Przejdź do artykułu

Autorzy i Afiliacje

P. Subashree
R. Thenmozhi

Abstrakt

The paper presents the experimental research and numerical simulations of reinforced concrete beams under torsional load. In the experimental tests Digital Image Correlation System (DIC System) Q-450 were used. DIC is a non-contact full-field image analysis method, based on grey value digital images that can determine displacements and strains of an object under load. Numerical simulations of the investigated beams were performed by using the ATENA 3D – Studio program. Creation of numerical models of reinforced concrete elements under torsion was complicated due to difficulties in modelling of real boundary conditions of these elements. The experimental research using DIC can be extremely useful in creating correct numerical models of investigated elements. High accuracy and a wide spectrum of results obtained from experimental tests allow for the modification of the boundary conditions assumed in the numerical model, so that these conditions correspond to the real fixing of the element during the tests.

Przejdź do artykułu

Autorzy i Afiliacje

B. Turoń
D. Ziaja
L. Buda-Ożóg
B. Miller

Abstrakt

In this study, the issue of intensity of cargo train-induced soil vibrations is presented. Oscillations were measured in Warsaw-Rembertow location with application of set of seismic receivers. The analysis concerns the ground vibration differentiation issue, depending on considered direction of oscillation propagation plane. Statistic distribution of vibration intensity for directions in 3-D space were done. The issue of potential effect on engineering structures of recorded vibrations was raised. The impact based on Scale of Dynamic Effects standard was estimated in the article. Vibration intensity results were also compared with classification according to the Swiss Standard.

Przejdź do artykułu

Autorzy i Afiliacje

K. Nielepkowicz
A. Bąkowska
M. Maślakowski

Abstrakt

The hereby paper discusses the influence of cable length on the SHM systems with the use of vibrating wire dynamic measurements. Vibrating wire sensors are mainly used for measuring stable or slowly changing strains, e.g. system installed on Rędziński Bridge in Wroclaw. From some time applications of these sensors for measuring dynamic deformations are becoming popular. Such tests were conducted on STS Fryderyk Chopin. New solutions generate new problems. In this case: the operational stability of systems exciting wire vibrations. The structure of such sensors and the electric cables length has an essential influence on their operations, what is undertaken in the paper. The subject of investigations constitutes the measuring system based on self-exciting impulse exciter, for which impedance parameters of electric cables and of the vibrating wire sensor were the most essential. The mathematical model of the system, experimental verification of the model as well as the results of theoretical analyses at the application of electric cables of various lengths are presented in the paper.

Przejdź do artykułu

Autorzy i Afiliacje

G. Cieplok
W. Karwowski
Ł. Bednarski

Abstrakt

Development of the transport infrastructure in Poland has contributed to the implementation of various technologies of construction of bridges and their components. Use of reinforced soil for construction of embankments, retaining structures (RSS walls) and abutments is one of the solutions which has been frequently used for the past twenty years. Shortly after its development, the technology proposed by Henri Vidal in 1966 also gained appreciation in Poland [4]. Reinforced soil bridge abutments started to be widely used in Poland at the turn of the 20th century. The bridge facilities at the junction of Trasa Siekierkowska route and Wał Miedzeszyński Street in Warsaw, which were built in the years 2000÷2002, are an example of structures from that period. The authors of this paper have been particularly interested in the outermost supports of the reinforced concrete flyovers which were constructed in the form of intermediate reinforced soil abutments. Offsets – the vertical displacements, in the range of 15÷25mm, emerging between the level of the road surface and the steel elements of the expansion joints which separate the flyover’s structure from the embankment – were observed in 2015, in the course of regular inspections. While accounting for the observations which have been made, the surveying measurements and the ground investigation, the paper diagnoses and describes the mechanism which led to the emergence of the offsets. Potential patterns of the occurrence of additional settlements, as the reason for emergence of the offsets, were identified and analyzed. The settlement of the outermost support (abutment), as a result of increase of relative density of alluvial sands due to the dynamic interaction of the roadways of Wał Miedzeszyński Street, was analyzed. Analytical and numeric approaches were used in the course of analysis while relying on PLAXIS and MIDAS software.

Przejdź do artykułu

Autorzy i Afiliacje

M. Bukowski
P. Łysiak
R. Oleszek
W. Trochymiak

Abstrakt

The article presents the results of the research on thermal actions on the materials occurring in the cross section along the depth of the bridge deck and bituminous pavement during its construction. The impulse to curried out the research was the need to explain the causes of the blistering of bituminous waterproofing membranes and asphalt pavements often observed on the bridge decks. The paper presents the examples of such failures and the analyses of possible mechanisms of the phenomenon. Research indicates a significant influence of all technological processes on the temperature of materials in the cross section as well as daily temperature changes. The probability of initiation of reactions between concrete components with gaseous products has been confirmed in such conditions. The susceptibility of bituminous materials to gas emission and blistering is the subject of a separate study. The research was part of a research project carried out under the contract INNOTECHK3/IN3/50/229332/NCBR /14 [13].

Przejdź do artykułu

Autorzy i Afiliacje

B. Chmielewska
A. Garbacz
G. Adamczewski
B. Rymsza

Abstrakt

The main problem of tunnelling with use of TBM in highly dense urban areas is to assign the range of subsiding trough and the impact of tunnelling works on existing buildings and underground or road infrastructure. The paper presents the results of settlements calculations over twin tube metro tunnel using analytical, empirical methods. The tunnel external diameter is 6,5 m ; the overburden vary from 5 m to 8 m ; the distance between tunnel axis is 14 m. Because of quaternary soils and high water table level the TBM type EBP was chosen as the method of tunnel construction. At the length of 502 m of tunnel the monitoring system was carried out in 22 cross sections. The results of settlements monitoring were compared with the values of analytical calculations.

Przejdź do artykułu

Autorzy i Afiliacje

A. Siemińska-Lewandowska
R. Kuszyk

Abstrakt

Buildings consume half of all energy use and are also responsible for a similar proportion of carbon dioxide emission. The heat transfer across the building envelope - the shell of a house that separates the inside and outside - should generally be minimized. In the paper validation and verification based on Building Energy Simulation Test (BESTEST) of Energy3D computer code is presented. Next, computations performed by means of Energy 3D and Energy Plus for BESTEST building are compared. In the last part of the paper results for computations for real building are presented. Program Energy 3D proved to be an excellent tool for qualitative and quantitative analysis of buildings with respect to energy consumption.

Przejdź do artykułu

Autorzy i Afiliacje

R.R. Gajewski
T. Kułakowski

Abstrakt

A review of mechanical models of road pavements in the form of a proposal of classification of these models is presented. It is assumed an autonomy of the following elements of pavement model: the models of structural layers, the subgrade model, the interlayer bonding models, including bonding of pavement structure with its subgrade, the models of external impacts on pavement layers, including load of heavy traffic, the models of pavement environment impacts on structural layers’ borders (lateral) and subgrade borders (including the lower one) – according to the selected criteria such as structural criterion, material criterion (physical criterion), dimension criterion and model scope (purpose) criterion − in the frame of assumptions of the classical Newtonian deterministic mechanics. The presented attempt to classify mechanical models of road pavements supports to orientate the roadmen community within a scope of the mechanistic modelling of these structures.

Przejdź do artykułu

Autorzy i Afiliacje

R. Nagórski

Abstrakt

The paper presents a description and results of a study focused on the applicability of the sclerometric method to the preliminary assessment of concrete quality in structures after fire. Due to the high thermal inertia, concrete has non-uniform properties in the heated element cross-section. The greatest reduction of concrete compressive strength occurs on the heated surface. When assessing a structure after a fire, it is particularly important to determine the thickness of the damaged external concrete layer. Reinforced concrete beams exposed to high temperature on one side (a one-way heat transfer in the cross-section) for 0 (unheated element), 60, 120, 180 and 240 minutes were examined. A significant decrease of the rebound number on the elements heated surface was observed, depending on the heating duration. The obtained values of the relative rebound number reduction were comparable to the values of relative compressive strength decrease (determined on the basis of temperature) of concrete situated 15 mm from the heated surface.

Przejdź do artykułu

Autorzy i Afiliacje

R. Kowalski
J. Wróblewska

Abstrakt

The paper presents results of the laboratory tests made for the prototype resilient under sleeper pads in the Warsaw University of Technology laboratory unit. These pads are dedicated to reduce vibrations transmitted to the vicinity of the railroad and to improve the resistance of the railroad structure. The laboratory testing program was carried out for elastomeric materials (polyurethane and rubber based) due to the PN-EN 16730 standard. The obtained values of the key parameters were used in order to determine the insertion loss vibration level by applying analytical method. The paper presents the influence of selected parameters i.e. static and dynamic moduli on the reduction of vibration and structure-borne sound level.

Przejdź do artykułu

Autorzy i Afiliacje

C. Kraśkiewicz
A. Zbiciak
W. Oleksiewicz
W. Karwowski

Abstrakt

This paper is entirely devoted to practical aspects of direct design and assessment of safety and serviceability of steel planar framework using advanced analysis. The development of advanced analysis has been driven by a desire for a more accurate representation of the behaviour of planar framework by considering the beam and spring numerical modelling technique together with plasticity and geometrically nonlinear effects as well as structural imperfections accounted for. The validated 2D version of CSD advanced analysis developed by the author is used in this paper for its practical application towards the resistance and serviceability assessment of existing simple construction framework. This steel braced frame was a subject of technical expertise. The same structure geometry but with different joint detailing is then considered to show how the effect of joint properties may affect the braced frame performance. Results of investigations are presented in the form of frame global response at both the ultimate limit state and the serviceability limit state, and also in the form of member local responses. Conclusions with regard to general design and assessment practice are drawn.

Przejdź do artykułu

Autorzy i Afiliacje

A.M. Barszcz

Abstrakt

The paper presents research program of bond between glass fiber reinforced polymer bars and concrete in reference to the steel bars. Bond between the reinforcement and concrete is a crucial parameter governing a behaviour of reinforced concrete members and transferring of the internal forces from concrete to the reinforcement. The use of FRP bars as an equivalent reinforcement to steel in concrete structures has increased in recent years. The FRP bars are very different from steel, mainly due to much lower elasticity modulus and their anisotropic structure. Good performance of FRP reinforced concrete requires sufficient interfacial bond between bars and concrete. However, there are no specific standards referring to the surface preparation of these bars, that leads to variable bond behaviour of the composite reinforcement to the concrete. The objective of the study was to investigate the influence of variable parameters on the bond behaviour to concrete. The experimental program consisted of eighteen beam bond specimens varying in: bar diameter (12 mm, 16 mm, 18 mm) and type of reinforcement (GFRP sand – coated and steel bars). Although the GFRP bars indicated good bond behaviour to concrete, the average bond strength was slightly lower than that of steel reinforcement of 16mm and 18 mm, while it was higher for the GFRP bars of 12 mm diameter.

Przejdź do artykułu

Autorzy i Afiliacje

D. Szczech
R. Kotynia

Abstrakt

Fiber reinforced polymers (FRPs) due to their specific high-strength properties become more and more popular and replace traditional structural materials like conventional steel in prestressed concrete structures. FRP reinforced structures are relatively new when compared to structures prestressed with steel tendons. For that reason only several studies and applications of pre-tensioned FRP reinforcement have been conducted until now. Moreover, researchers only considered short-term behavior of FRP reinforced concrete members. The precise information about long-term behavior of FRP reinforcement is necessary to evaluate the prestress losses, which should be taken into account in the design of prestressed RC structures. One of the most important factor influencing long term behavior of FRP reinforcement is stress relaxation. The overview of experimental tests results described in the available literature considering the prestress losses obtained in FRP prestressed concrete members is presented herein.

Przejdź do artykułu

Autorzy i Afiliacje

M. Przygocka
R. Kotynia

Abstrakt

The aim of the paper is to investigate the shear failure mechanisms in T-shape, single span and simply supported beams exclusively reinforced with longitudinal glass fiber reinforced polymer (GFRP) bars. Usually the critical shear crack in RC beams without stirrups develops through the theoretical compression strut reducing the shear strength following the shear failure. The main parameter affecting the crack pattern and the shear strength of the beams is the shear slenderness. However, the test results presented in the paper indicated the new arching effect due to the bond losing between the GFRP flexural reinforcement and concrete. This failure mode revealed unexpected critical crack pattern and failure mode. The research of concrete beams flexurally reinforced with GFRP bars without stirrups indicated two failure modes: typical shear-compression and a new one leading by the bond losing between the ordinary reinforcement and concrete.

Przejdź do artykułu

Autorzy i Afiliacje

M. Kaszubska
R. Kotynia

Abstrakt

Increasingly complex design systems require an individual approach when determining the necessary design parameters. As soils are characterized by strong strain-dependent nonlinearity, test methods used to characterize the subsoil should be carefully selected, in terms of their "sensitivity" as well as suitability for the analyzed type of problem. When direct measurements are not available, while design calculation models require specific parameters, indirect parameter estimation may be used. This approach requires calibration and validation of empirical correlations, based on well documented database of tests and case studies. One of the parameters often used, when analyzing soil-structure interaction problems, is the shear stiffness of the soil and its strain-dependent degradation. The aim of the article is to present the procedure for description and evaluation of soil stiffness based on field tests (CPTU, DMT and SDMT) and a large number of reference curves obtained from laboratory tests (TRX) for selected soil types. On the basis of the given algorithm, it is possible to obtain a stiffness module G0 value at any level of deformation, based on in-situ tests.

Przejdź do artykułu

Autorzy i Afiliacje

T. Godlewski

Abstrakt

The aim of the study was to develop a practical approach to parametric shaping of spatial steel rod structures formed based on a hyperbolic paraboloid. This design approach was realized by application of designing tools working in environment of Rhinoceros 3D, that is its plug-in Grasshopper for geometric modelling and Karamba 3D for structural analysis. The goal of this research was to elaborate an universal scripts in order to create rod structures‘ models of various forms and grid patterns, as well as evaluating their structural behaviour dependently on various boundary conditions. The optimisation criterion was the minimum mass and deflection. Several proposals of coverings by means of single layer grid structures were presented and analysed to choose the best solution. The rod structures generated based on a hyperbolic paraboloid turned out to be structures with good static properties, so may be an interesting proposals to cover large areas.

Przejdź do artykułu

Autorzy i Afiliacje

J. Dzwierzynska

Zasady etyki publikacyjnej

ETHICS POLICY

”Archives of Civil Engineering” respects and promotes the principles of publishing ethics. Being guided by COPE’s Guidelines ( https://publicationethics.org/resources/guidelines) we ensure that all participants of the publishing process comply with these rules, the journal pays special attention to:

Editor Responsibilities
1. Qualifying individual manuscripts for publication only on the basis of: (a) compliance with the guidelines provided to the authors, (b) substantive value, (c) originality, (d) transparency of presentation
2. Deciding whether the paper fulfills all requirements i.e. formal and scientific and which articles submitted to the journal should be published. In making these decisions, the editor may be guided by the policies of the journal’s editorial board as well as by legal requirements regarding libel, copyright infringement, and plagiarism.
3. Evaluating manuscripts for intellectual content without regard to race, gender, sexual orientation, religious belief, ethnic origin, citizenship, or political philosophy of the author(s).
4. Ensuring scientific accuracy and complying with the principle of authorship; making sure that individual authors who contribute to the publication accept its form after the scientific editing
5. Providing a fair and appropriate peer review process.
6. Withdrawing manuscripts from publication, if any information about its unreliability appeared, also as a result of unintentional errors, features of plagiarism or violation of the rules of publishing ethics were identified.
7. Requiring all contributors to disclose relevant competing interests and publish corrections if competing interests are revealed after publication. If needed, other appropriate action should be taken, such as the publication of a retraction or expression of concern.
8. Maintaining the integrity of the academic record, precludes business needs from compromising intellectual and ethical standards, and is always willing to publish corrections, clarifications, retractions, and apologies when needed.
9. Not disclosing any information about a manuscript under consideration to anyone other than the author(s), reviewers and potential reviewers, and in some instances the editorial board members, as appropriate.

Reviewer Responsibilities
1. Cooperating with the scientific editor and / or editorial office and the authors in the field of improving the reviewed material;
2. Being objective and expressing the views clearly with appropriate supporting arguments.
3. Assessing of the entrusted works in a careful and objective manner, if possible with an assessment of their scientific reliability and with appropriate justification of the comments submitted;
4. identifying relevant published work that has not been cited by the authors
5. calling to the editor's attention any substantial similarity or overlap between the manuscript under consideration and any other published data of which they have personal knowledge
6. Maintaining the principle of fair play, excluding personal criticism of the author (s)
7. Maintaining confidentiality, which is not showing or discussing with others except those authorized by the editor. Any manuscripts received for review are treated as confidential documents.
8. Performing a review within the set time limit or accepting another solution jointly with ACE in the event of failure to meet this deadline.
9. Notifying the editor if the invited reviewer feels unqualified to review the manuscript or knows that its timely review will be impossible.
10. identifying relevant published work that has not been cited by the authors
11. Not considering evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relationships or connections with any of the authors, companies, or institutions connected to the submission.

Author Responsibilities
1. Results of original research should present an accurate account of the work performed as well as an objective discussion of its significance. Underlying data should be represented accurately in the manuscript. A paper should contain sufficient detail and references to permit others to replicate the work. Fraudulent or knowingly inaccurate statements constitute unethical behaviour and are unacceptable.
2. The authors should follow the principle of originality, which is submitting only their own original works, and in the case of using the works of other authors, marking them in accordance with the rules of quotation, or obtaining consent for the publication of previously published materials from their owners or administrators;
3. An author should not in general publish manuscripts describing essentially the same research in more than one journal or primary publication. Parallel submission of the same manuscript to more than one journal constitutes unethical publishing behaviour and is unacceptable.
4. Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the reported study and phenomena such as ghostwriting or guest authorship in the event of their detection must be actively counteracted.
5. All authors should report in a Reliable manner the sources they used to create their own study and their inclusion in the attachment bibliography;
6. All those who have made significant contributions should be listed as co-authors. Where there are others who have participated in certain substantive aspects of the research project, they should be named in an Acknowledgement section.
7. The corresponding author should ensure that all appropriate co-authors (according to the above definition) and no inappropriate co-authors are included in the author list of the manuscript, and that all co-authors have seen and approved the final version of the paper and have agreed to its submission for publication.
8. All authors should disclose in their manuscript any financial or other substantive conflict of interest that might be construed to influence the results or their interpretation in the manuscript. All sources of financial support for the project should be disclosed.
9. When an author discovers a significant error or inaccuracy in his/her own published work, it is the author’s obligation to promptly notify the journal’s editor or publisher and cooperate with them to either retract the paper or to publish an appropriate erratum.

Publisher’s Confirmation
In cases of alleged or proven scientific misconduct, fraudulent publication or plagiarism the publisher, in close collaboration with the editors, will take all appropriate measures to clarify the situation and to amend the article in question. This includes the prompt publication of an erratum or, in the most severe cases, the complete retraction of the affected work.

Procedura recenzowania

Manuscript Peer-Review Procedure

”Archives of Civil Engineering” makes sure to provide transparent policies for peer-review, and reviewers have an obligation to conduct reviews in an ethical and accountable manner. There is clear communication between the journal and the reviewers which facilitates consistent, fair, and timely review.

-The model of peer-review is double-blind: the reviewers do not know the names of the authors, and the authors do not know who reviewed their manuscript (but if the research is published reviewers can eventually know the names of the authors). A complete list of reviewers is published in a traditional version of the journal: in-print.
-It is the editor who appoints two reviewers; however, if there are discrepancies in the assessment the third reviewer can be appointed.
-After having accepted to review the manuscript (one-week deadline), the reviewers have approximately 6 weeks to finish the process.
-The paper is published in ACE provided that the reviews are positive. All manuscripts receive grades from 1-5, 5 being positive, 1 negative, the authors receive reviews to read and consider the comments.
-Manuscript evaluations are assigned one of five outcomes: accept without changes, accept after changes suggested by the reviewer, rate manuscript once again after major changes and another review, reject, withdraw.
-Manuscripts requiring minor revision (accept after changes suggested by the reviewer) does not require a second review. All manuscripts receiving a "Rate manuscript once again after major changes and another review " evaluation must be subjected to a second review. Rejected manuscripts are given no further consideration. There are cases when the article can be withdrawn, often upon the request of an author, technical reason (e.g. names of authors are placed in the text, lack of references, or inappropriate structure of the text), or plagiarism.
-The revised version of the manuscript should be uploaded to the Editorial System within six weeks. If the author(s) failed to make satisfactory changes, the manuscript is rejected.
-On acceptance, manuscripts are subject to editorial amendment to suit house style.
-Paper publication requires the author's final approval.
- As soon as the publication appears in print and in electronic forms on the Internet there is no possibility to change the content of the article.

Editor’s responsibilities
-The editor decides whether the paper fulfills all requirements i.e. formal and scientific and which articles submitted to the journal should be published.
-In making these decisions, the editor may be guided by the policies of the journal’s editorial board as well as by legal requirements regarding libel, copyright infringement, and plagiarism.
-The editor maintains the integrity of the academic record, precludes business needs from compromising intellectual and ethical standards, and is always willing to publish corrections, clarifications, retractions, and apologies when needed.
-The editor evaluates manuscripts for intellectual content without regard to race, gender, sexual orientation, religious belief, ethnic origin, citizenship, or political philosophy of the author(s).
-The editor does not disclose any information about a manuscript under consideration to anyone other than the author(s), reviewers and potential reviewers, and in some instances the editorial board members, as appropriate.

Reviewers' responsibilities
Any manuscripts received for review are treated as confidential documents. They must not be shown to or discussed with others except if authorized by the editor. Privileged information or ideas obtained through peer review is kept confidential and not used for personal advantage Any invited reviewer who feels unqualified to review the manuscript or knows that its timely review will be impossible should immediately notify the editor so that alternative reviewers can be contacted. Reviewers should identify relevant published work that has not been cited by the authors. Any statement that an observation, derivation, or argument had been previously reported should be accompanied by the relevant citation. A reviewer should also call to the editor's attention any substantial similarity or overlap between the manuscript under consideration and any other published data of which they have personal knowledge. Reviewers should not consider evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relationships or connections with any of the authors, companies, or institutions connected to the submission. Reviews should be conducted objectively. Personal criticism of the author is unacceptable. Referees should express their views clearly with appropriate supporting arguments. All reviews must be carried out on a special form available in the Editorial System.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji