Nauki Techniczne

Opto-Electronics Review

Zawartość

Opto-Electronics Review | 2023 | 31 | special issue

Abstrakt

The operation of narrow-gap semiconductor devices under non-equilibrium mode is used at temperatures where the materials are normally intrinsic. The phenomenon of minority carrier exclusion and extraction was particularly discussed in the case of the suppression of Auger thermal generation in heterojunction photodiodes, especially important in the long-wave infrared range. This paper shows that the reduction of the dark current in the HgCdTe photodiode operating in the mid-wave infrared range is primarily the result of suppression of the Shockley-Read-Hall generation in the non-equilibrium absorber. Under a reverse bias, the majority carrier concentration is held equal to the majority carrier doping level. This effect also leads to a decreased majority carrier population at the trap level and an effective increase in the carrier lifetime. The analysed device was with the following design: p+-Bp cap-barrier unit, p-type absorber doped at the level of 8 ·1015 cm−3, and wide-bandgap N+ bottom contact layer. At room temperature, the lowest dark current density of 3.12 ·10−1 A/cm2 was consistent with the theoretically predicted Shockley-Read-Hall suppression mechanism, about two times smaller than for the equilibrium case.
Przejdź do artykułu

Autorzy i Afiliacje

Małgorzata Kopytko
1
ORCID: ORCID

  1. Institute of Applied Physics, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00 908 Warsaw, Poland

Abstrakt

In the past ten years, InAs/InAsSb type-II superlattice has emerged as a promising technology for high-temperature mid-wave infrared photodetector. Nevertheless, transport properties are still poorly understood in this type of material. In this paper, optical and electro-optical measurements have been realised on InAs/InAsSb type-II superlattice mid-wave infrared photodetectors. Quantum efficiency of 50% is measured at 150 K, on the front side illumination and simple pass configuration. Absorption measurement, as well as lifetime measurement are used to theoretically calculate the quantum efficiency thanks to Hovel’s equation. Diffusion length values have been extracted from this model ranging from 1.55 µm at 90 K to 7.44 µm at 200 K. Hole mobility values, deduced from both diffusion length and lifetime measurements, varied from 3.64 cm²/Vs at 90 K to 37.7 cm²/Vs at 200 K. The authors then discuss the hole diffusion length and mobility variations within temperature and try to identify the intrinsic transport mechanisms involved in the superlattice structure.
Przejdź do artykułu

Autorzy i Afiliacje

Maxime Bouschet
1 2
Vignesh Arounassalame
3
Anthony Ramiandrasoa
3
Jean-Philippe Perez
1
Nicolas Péré-Laperne
2
Isabelle Ribet-Mohamed
3
Philippe Christol
1

  1. IES, Université de Montpellier, CNRS, 860 Saint Priest St., F-34000 Montpellier, CEDEX 5, France
  2. LYNRED, BP 21, 364 de Valence Ave., 38113 Veurey-Voroize, France
  3. ONERA, Chemin de la Hunière, F-91761 Palaiseau Cedex, France

Abstrakt

Germanium (Ge) PiN photodetectors are fabricated and electro-optically characterised. Unintentionally and p-type doped Ge layers are grown in a reduced-pressure chemical vapour deposition tool on a 200 mm diameter, <001>-oriented, p-type silicon (Si) substrates. Thanks to two Ge growth temperatures and the use of short thermal cycling afterwards, threading dislocation densities down to 107 cm−2 are obtained. Instead of phosphorous (P) ion implantation in germanium, the authors use in situ phosphorous-doped poly-crystalline Si (poly-Si) in the n-type regions. Secondary ion mass spectrometry revealed that P was confined in poly-Si and did not diffuse in Ge layers beneath. Over a wide range of tested device geometries, production yield was dramatically increased, with almost no short circuits. At 30 °C and at −0.1 V bias, corresponding to the highest dynamic resistance, the median dark current of 10 µm diameter photodiodes is in the 5–20 nA range depending on the size of the n-type region. The dark current is limited by the Shockley-Read-Hall generation and the noise power spectral density of the current by the flicker noise contribution. A responsivity of 0.55 and 0.33 A/W at 1.31 and 1.55 µm, respectively, is demonstrated with a 1.8 µm thick absorption Ge layer and an optimized anti-reflection coating at 1.55 µm. These results pave the way for a cost-effective technology based on group-IV semiconductors.
Przejdź do artykułu

Autorzy i Afiliacje

Quentin Durlin
1
Abdelkader Aliane
1
Luc André
1
Hacile Kaya
1
Mélanie Le Cocq
1
Valérie Goudon
1
Claire Vialle
1
Marc Veillerot
1
Jean-Michel Hartmann
1

  1. Univ. Grenoble Alpes, CEA-Leti, F-38000 Grenoble, France

Abstrakt

This paper presents examples of infrared detectors with mercury cadmium telluride elaborated at the Institute of Applied Physics, Military University of Technology and VIGO Photonics S.A. Fully doped HgCdTe epilayers were grown with the metal organic chemical vapour deposition technique which provides a wide range of material composition covering the entire infrared range from 1.5 µm to 14 µm. Fundamental issues concerning the design of individual areas of the heterostructure including: the absorber, contacts, and transient layers with respect to their thickness, doping and composition were discussed. An example of determining the gain is also given pointing to the potential application of the obtained devices in avalanche photodiode detectors that can amplify weak optical signals. Selected examples of the analysis of current-voltage and spectral characteristics are shown. Multiple detectors based on a connection in series of small individual structures are also presented as a solution to overcome inherent problems of low resistance of LWIR photodiodes. The HgCdTe detectors were compared with detectors from III-V materials. The detectors based on InAs/InAsSb superlattice materials achieve very comparable parameters and, in some respects, they are even superior to those with mercury cadmium telluride.
Przejdź do artykułu

Autorzy i Afiliacje

Paweł Madejczyk
1
ORCID: ORCID
Waldemar Gawron
1 2
ORCID: ORCID
Jan Sobieski
2
ORCID: ORCID
Piotr Martyniuk
1
ORCID: ORCID
Jarosław Rutkowski
1
ORCID: ORCID

  1. Institute of Applied Physics, Military University of Technology, 2 gen. Kaliskiego St., 00-908 Warsaw, Poland
  2. Vigo Photonics S.A., 129/133 Poznańska St., 05-850 Ożarów Mazowiecki, Poland

Abstrakt

In this work, the authors investigated the influence of proton-irradiation on the dark current of XBp longwave infrared InAs/GaSb type-II superlattice barrier detectors, showing a cut-off wavelength from 11 µm to 13 µm at 80 K. The proton irradiations were performed with 63 MeV protons and fluences up to 8∙1011 H+/cm² on a type-II superlattice detector kept at cryogenic (100 K) or room temperature (300 K). The irradiation temperature of the detector is a key parameter influencing the effects of proton irradiation. The dark current density increases due to displacement damage dose effects and this increase is more important when the detector is proton-irradiated at room temperature rather than at cryogenic temperature.
Przejdź do artykułu

Autorzy i Afiliacje

Clara Bataillon
1
Jean-Phillipe Perez
1
Rodolphe Alchaar
1
Alain Michez
1
Olivier Gilard
2
Olivier Saint-Pé
3
Philippe Christol
1

  1. University of Montpellier, 163 Auguste Broussonnet St., 34090 Montpellier, France
  2. CNES, 18 Edouard Belin Ave., 31400 Toulouse, France
  3. Airbus Defense & Space, 31 des Cosmonautes St., 31400 Toulouse, France

Abstrakt

Current advances in type-II superlattice (T2SL) research at Fraunhofer IAF are elaborated on in this paper. First, the use of metastructures for quantum efficiency (QE) enhancement in the longwave infrared (LWIR) is presented. Finite element modelling results are reported on that suggest a potential for doubling of the QE at certain wavelengths with the investigated device structure. Next, characterisation results of midwave infrared (MIWR) InAs/InAsSb T2SL nBn detectors are shown. The low, diffusion-limited dark current above 120 K and a QE of 60% are comparable to the state-of-the-art. Finally, groundwork for InAs/GaSb T2SL MWIR/LWIR dual-band detector arrays based on a back-to-back heterojunction diode device concept is presented. The dry etching technology allows for steep etch trenches and full pixel reticulation with a fill factor of about 70% at 12 µm pitch. The detector characterisation at 77 K and ±250 mV bias demonstrates the bias-switchable operation mode with dark current densities of 6.1·10−9 A/cm² in the MWIR and 5.3·10−4 A/cm² in the LWIR.
Przejdź do artykułu

Autorzy i Afiliacje

Raphael Müller
1
Volker Daumer
1
Tsvetelina Hugger
1
Lutz Kirste
1
Wolfgang Luppold
1
Jasmin Niemasz
1
Robert Rehm
1
Tim Stadelmann
1
Mark Wobrock
1
Quankui Yang
1

  1. Fraunhofer Institute for Solid State Physics IAF, Tullastraße 72, 79108 Freiburg, Germany

Abstrakt

The sensitivity of III-V-based infrared detectors is critically dependent upon the carrier concentration and mobility of the absorber layer, and thus, accurate knowledge of each is required to design structures for maximum detector performance. Here, measurements of the bulk in-plane resistivity, in-plane mobility, and carrier concentration as a function of temperature are reported for non-intentionally doped and Si-doped mid-wave infrared InAs0.91Sb0.09 alloy and InAs/InAs0.65Sb0.35 type-II superlattice materials grown on GaSb substrates. Standard temperature- and magnetic-field-dependent resistivity and the Hall measurements on mesa samples in the van der Pauw configuration are performed, and multi-carrier fitting and modelling are used to isolate transport of each carrier species. The results show that up to 5 carrier species of the surface, interface and bulk variety contribute to conduction, with bulk electron and hole mobility up to 2·105 cm2/V s and 8·103 cm2/V s, respectively and background dopant concentration levels were between 1014 and 1015 cm−3. The in-plane mobility temperatures dependence is determined and trends of each carrier species with temperature and dose are analysed.
Przejdź do artykułu

Autorzy i Afiliacje

Christian P. Morath
1
ORCID: ORCID
Lilian K. Casias 
2
ORCID: ORCID
Gilberto A. Umana-Membreno 
3
ORCID: ORCID
Preston T. Webster
1
Perry C. Grant 
1
ORCID: ORCID
Diana Maestas
1
Vincent M. Cowan
1
ORCID: ORCID
Lorenzo Faraone 
3
ORCID: ORCID
Sanjay Krishna 
4
ORCID: ORCID
Ganesh Balakrishnan
5
ORCID: ORCID

  1. U.S. Air Force Research Lab Space Vehicles Directorate, 3550 Kirtland AFB, 427 Aberdeen Ave., NM 87117, USA
  2. Sandia National Laboratories, 1515 Eubank Blvd. SE, Albuquerque, NM 87185, USA
  3. School of Electrical, Electronic, and Computer Engineering, The University of Western Australia, 25 Fairway, Crawley WA 6009, Australia
  4. Department of Electrical Engineering, The Ohio State University, 2015 Neil Ave., Columbus, OH 43210, USA
  5. Center for High Technology Materials, University of New Mexico, 1313 Goddard St. SE, Albuquerque, NM 87106, USA

Abstrakt

This work investigates the potential of InAs/GaSb superlattice detectors for the short-wavelength infrared spectral band. A barrier detector structure was grown by molecular beam epitaxy and devices were fabricated using standard photolithography techniques. Optical and electrical characterisations were carried out and the current limitations were identified. The authors found that the short diffusion length of ~1.8 µm is currently limiting the quantum efficiency (double-pass, no anti-reflection coating) to 43% at 2.8 µm and 200 K. The dark current density is limited by the surface leakage current which shows generation-recombination and diffusion characters below and above 195 K, respectively. By fitting the size dependence of the dark current, the bulk values have been estimated to be 6.57·10−6 A/cm2 at 200 K and 2.31·10−6 A/cm2 at 250 K, which is only a factor of 4 and 2, respectively, above the Rule07.
Przejdź do artykułu

Autorzy i Afiliacje

Marie Delmas
1
David Ramos
1 2
Ruslan Ivanov
1
Laura Žurauskaitė
1
Dean Evans
1
David Rihtnesberg
1
Susanne Almqvist
1
Smilja Becanovic
1
Eric Costard
1
Linda Höglund
1

  1.  IRnova AB, Isafjordsgatan 22, Kista 164 40, Sweden
  2. School of Electrical Engineering and Computer Science KTH Royal Institute of Technology, Isafjordsgatan 22, Kista 164 40, Sweden

Abstrakt

This work investigates the potential of p-type InAs/GaSb superlattice for the fabrication of full mid-wave megapixel detectors with n-on-p polarity. A significantly higher surface leakage is observed in deep-etched n-on-p photodiodes compared to p-on-n diodes. Shallow-etch and two-etch-step pixel geometry are demonstrated to mitigate the surface leakage on devices down to 10 µm with n-on-p polarity. A lateral diffusion length of 16 µm is extracted from the shallow etched pixels, which indicates that cross talk could be a major problem in small pitch arrays. Therefore, the two-etch-step process is used in the fabrication of 1280 × 1024 arrays with a 7.5 µm pitch, and a potential operating temperature up to 100 K is demonstrated.
Przejdź do artykułu

Autorzy i Afiliacje

David Ramos
1 2
Marie Delmas
1
Ruslan Ivanov
1
Laura Žurauskaitė
1
Dean Evans
1
Susanne Almqvist
1
Smilja Becanovic
1
Per-Erik Hellström
2
Eric Costard
1
Linda Höglund
1

  1. IRnova AB, Isafjordsgatan 22, Kista 164 40, Sweden
  2.  School of Electrical Engineering and Computer Science KTH Royal Institute of Technology, Isafjordsgatan 22, Kista 164 40, Sweden

Abstrakt

Short-period 10 monolayers InAs/10ML GaSb type-II superlattices have been deposited on a highly lattice-mismatched GaAs (001), 2° offcut towards <110> substrates by molecular beam epitaxy. This superlattice was designed for detection in the mid-wave infrared spectral region (cut-off wavelength, λcut-off = 5.4 µm at 300 K). The growth was performed at relatively low temperatures. The InAs/GaSb superlattices were grown on a GaSb buffer layer by an interfacial misfit array in order to relieve the strain due to the ~7.6% lattice-mismatch between the GaAs substrate and type-II superlattices. The X-ray characterisation reveals a good crystalline quality exhibiting full width at half maximum ~100 arcsec of the zero-order peak. Besides, the grown samples have been found to exhibit a change in the conductivity.
Przejdź do artykułu

Autorzy i Afiliacje

Piotr Martyniuk
1
ORCID: ORCID
Djalal Benyahi
2
ORCID: ORCID

  1. Institute of Applied Physics, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
  2. Laboratoire des Systèmes Lasers, École Militaire Polytechnique, BP 17 Bordj El Bahri, 16111 Algiers, Algeria

Abstrakt

In recent years, type-II superlattice-based devices have completed the offer of the electronic industry in many areas of applications. Photodetection is one of them, especially in the mid-infrared wavelength range. It is due to the unique feature of a superlattice material, which is a tuneable bandgap. It is also believed that the dark current of superlattice-based photodetectors is strongly suppressed due to the suppression of the band-to-band tunnelling current in a superlattice material. This argument relies, however, on a semi-classical approach that treats superlattice as a bulk material with effective parameters extracted from the kp analysis. In the paper, a superlattice device is analysed on a quantum level: the non-equilibrium Green’s function method is applied to the two-band Hamiltonian of the InAs/GaSb superlattice p-i-n diode. The analysis concentrates on the band-to-band tunnelling with the aim to validate the correctness of a semi-classical description of the phenomenon. The results of calculations reveal that in a superlattice diode, the inter-band tunnelling occurs only for certain values of energy and in-plane momentum, for which electronic and hole sub-bands cross. The transitions occurring for vanishing in-plane momentum produce resonances in the current-voltage characteristics – the feature which was reported in a few experimental observations. This scenario is quite different from that occurring in bulk materials, where there is a range of energy-momentum pairs for which the band-to-band tunnelling takes place, and so current-voltage characteristics are free from any resonances. However, simulations show that, while not justified for a detailed analysis, the semi-classical description can be applied to superlattice-based devices for an ‘order of magnitude’ estimation of the band-to-band tunnelling current.
Przejdź do artykułu

Autorzy i Afiliacje

Marcin Makowiec
1
ORCID: ORCID
Andrzej Kolek
1
ORCID: ORCID

  1. Department of Electronics Fundamentals, Rzeszow University of Technology, al. Powstańców Warszawy 12, Rzeszów 35-959, Poland

Abstrakt

The electronic quasi-bound state in the continuum concept is explored in an InGaAs/InAlAs heterostructure to create a voltage-tunable dual-colour quantum Bragg mirror detector. This heterostructure is based on one main quantum well embedded between two different superlattices. By bandgap engineering, each superlattice gives rise to quasi-bound states in the continuum with a preferential direction for electron extraction. Due to these states, the photovoltaic photocurrent presents a dual-colour response, one in a positive direction at 340 meV (3.6 µm), and one in a negative direction at 430 meV (2.9 µm). The simultaneous dual-colour detection can be switched to a single-colour detection (340 meV or 430 meV) by applying a bias voltage. At 77 K, the specific detectivity for simultaneous dual-colour is 2.5·108 Jones, while the single-colour detectivities are 2.6·109 Jones at +2.0 V and 7.7·108 Jones at −1.6 V for 340 meV and 430 meV, respectively.
Przejdź do artykułu

Autorzy i Afiliacje

Germano M. Penello
1 2
ORCID: ORCID
Pedro H. Pereira
3 2
ORCID: ORCID
Vitor B. Sousa
3 2
Rudy M. S. Kawabata
3 2
Mauricio P. Pires
1 2
Patricia L. Souza
3 2

  1. Instituto de Física, Universidade Federal do Rio de Janeiro, R. Athos Silveira Ramos 149, Rio de Janeiro 21941-909, Brasil
  2. DISSE, Instituto Nacional de Ciência e Tecnologia de Nanodispositivos Semiconductores, R. Marquês de São Vicente 225, Gávea, Rio de Janeiro, 22451-900, Brasil
  3. LabSem/CETUC, Pontifícia Universidade Católica do Rio de Janeiro, R. Marquês de São Vicente 124, Gávea, Rio de Janeiro 22451-040, Brasil

Abstrakt

Dual-band infrared detector, which acquires more image information than single-band detectors, has excellent detection, recognition, and identification capabilities. The dual-band detector can have two bumps to connect with each absorber layer, but it is difficult to implement small pitch focal plane arrays and its fabrication process is complicated. Therefore, the most effective way for a dual-band detector is to acquire each band by bias-selectable with one bump. To aim this, a dual-band MWIR/LWIR detector based on an InAs/GaSb type-II superlattice nBn structure was designed and its performance was evaluated in this work. Since two absorber layers were separated by the barrier layer, each band can be detected by bias-selectable with one bump. The fabricated dual-band device exhibited the dark current and spectral response characteristics of MWIR and LWIR bands under negative and positive bias, respectively. Spectral crosstalk that is a major issue in dual-band detectors was also improved. Finally, a 20 μm pitch 640 × 512 dual-band detector was fabricated, and both MWIR and LWIR images exhibited an average noise equivalent temperature difference of 30 mK or less at 80 K.
Przejdź do artykułu

Autorzy i Afiliacje

Hyun-Jin Lee
1
ORCID: ORCID
Jun Ho Eom
1
Hyun Chul Jung
1
Ko-Ku Kang
1
Seong Min Ryu
1
Ahreum Jang
1
Jong Gi Kim
1
Young Ho Kim
1
Han Jung
1
Sun Ho Kim
2
Jong Hwa Choi
2

  1.  i3system, Inc., 26-32, Gajeongbuk-ro, Yuseong-gu, Daejeon, 34113, Republic of Korea
  2. Agency of Defense Development, 34186 P.O.Box 35, Yuseong-gu, Daejeon, Republic of Korea

Abstrakt

In the last decade, infrared imaging detectors trend has gone for smaller pixels and larger formats. Most of the time, this scaling is carried out at a given total sensitive area for a single focal plane array. As an example, QVGA 30 µm pitch and VGA 15 µm pitch exhibit exactly the same sensitive area. SXGA 10 µm pitch tends to be very similar, as well. This increase in format is beneficial to image resolution. However, this scaling to even smaller pixels raises questions because the pixel size becomes similar to the IR wavelength, but also to the typical transport dimensions in the absorbing material. Hence, maintaining resolution for such small pixel pitches requires a good control of the modulation transfer function and quantum efficiency of the array, while reducing the pixel size. This might not be obtained just by scaling the pixel dimensions. As an example, bulk planar structures suffer from excessive lateral diffusion length inducing pixel-to-pixel cross talk and thus degrading the modulation transfer function. Transport anisotropy in some type II superlattice structures might also be an issue for the diffusion modulation transfer function. On the other side, mesa structures might minimize cross talk by physically separating pixels, but also tend to degrade the quantum efficiency due to a non-negligible pixel fill factor shrinking down the pixel size. This paper discusses those issues, taking into account different material systems and structures, in the perspective of the expected future pixel pitch infrared focal plane arrays.
Przejdź do artykułu

Autorzy i Afiliacje

Olivier Gravrand 
1
Nicolas Baier 
1
Alexandre Ferron 
1
Florent Rochette  
1
Clément Lobre 
1
Jocelyn Bertoz 
2
Laurent Rubaldo
2

  1. CEA-LETI, 17 des Martyrs St., 38054 Grenoble, France
  2. Lynred, BP 21, 38113 Veurey-Voroize, France

Abstrakt

The viability of epitaxial regrowth of non-intentionally doped InP to passivate lateral mesa surfaces of InGaAs photodiodes lattice-matched to InP is investigated, evaluating whether the residual doping of the regrown layer can be responsible for an unexpected increase of the surface current. The effect of residual doping is evaluated via numerical calculations of dark current, considering the range of doping concentrations expected for non-intentionally doped InP. The calculations show that the increase in dark current due to the residual doping of the regrown InP layer is not enough to justify the observed increase in surface current. On the other hand, the technique is still valid as a passivation method if the photodetector pixel is isolated by etching only the top contact layer.
Przejdź do artykułu

Autorzy i Afiliacje

Osvaldo M. Braga
1
Cristian A. Delfino
1
Rudy M. S. Kawabata
2
Luciana D. Pinto
2
Gustavo S. Vieira
1
Maurício P. Pires
3
Patricia L. Souza
2
Euclydes Marega
4
John A. Carlin
5
Sanjay Krishna
5

  1. Institute for Advanced Studies, IEAV, 12228-001, São Paulo, Brazil
  2. LabSem, CETUC, Pontifícia Universidade Católica, PUC-Rio, R. Marquês de São Vicente 124, Gávea, 22451-900 Rio de Janeiro, Brazil
  3. Physics Institute, Federal University of Rio de Janeiro, Av. Athos da Silveira Ramos 149, 21941-909 Rio de Janeiro, Brazil
  4. Universidade de São Paulo, USP-São Carlos, 13566-560 São Carlos, SP, Brazil
  5. Ohio State University, 281 W Lane Ave., Columbus, OH 43210, USA

Abstrakt

The authors report the characteristics of a diffraction-grating-free mid-wavelength infrared InP/In0.85Ga0.15As quantum well infrared photodetector focal plane array with a 640 × 512 format and a 15 m pitch. Combination of a normal incident radiation sensing ability of the high-x InxGa1-xAs quantum wells with a large gain property of the InP barriers led to a diffraction-grating-free quantum well infrared photodetector focal plane array with characteristics displaying great promise to keep the status of the quantum well infrared photodetector as a robust member of the new generation thermal imaging sensor family. The focal plane array exhibited excellent uniformity with noise equivalent temperature difference nonuniformity as low as 10% and a mean noise equivalent temperature difference below 20 mK with f/2 optics at 78 K in the absence of grating. Elimination of the diffraction-grating and large enough conversion efficiency (as high as 70% at a −3.5 V bias voltage) abolish the bottlenecks of the quantum well infrared photodetector technology for the new generation very small-pitch focal plane arrays.
Przejdź do artykułu

Autorzy i Afiliacje

Cengiz Besikci
1 2
ORCID: ORCID
Saadettin V. Balcı
1
ORCID: ORCID
Onur Tanış
2
Oğuz O. Güngör
2
ORCID: ORCID
Esra S. Arpaguş
2

  1. Micro and Nanotechnology Program, Graduate School of Natural and Applied Sciences, Middle East Technical University, Dumlupınar Bulvarı 1, 06800 Ankara, Turkey
  2. Electrical and Electronics Engineering Department, Middle East Technical University, Dumlupınar Bulvarı 1, 06800 Ankara, Turkey

Abstrakt

The article presents the results of diameter mapping for circular-symmetric disturbance of homogeneity of epitaxially grown InAs (100) layers on GaAs substrates. The set of acceptors (beryllium) doped InAs epilayers was studied in order to evaluate the impact of Be doping on the 2-inch InAs-on-GaAs wafers quality. During the initial identification of size and shape of the circular pattern, non-destructive optical techniques were used, showing a 100% difference in average roughness between the wafer centre and its outer part. On the other hand, no volumetric (bulk) differences are detectable using Raman spectroscopy and high-resolution X-ray diffraction. The correlation between Be doping level and circular defect pattern surface area has been found.
Przejdź do artykułu

Autorzy i Afiliacje

Jacek Boguski
1
ORCID: ORCID
Jarosław Wróbel
1
ORCID: ORCID
Sebastian Złotnik
1
ORCID: ORCID
Bogusław Budner
2
Malwina Liszewska
2
Łukasz Kubiszyn
3
ORCID: ORCID
Paweł P. Michałowski
2
Łukasz Ciura
4
Paweł Moszczyński
5
ORCID: ORCID
Sebastian Odrzywolski
1
Bartłomiej Jankiewicz
2
Jerzy Wróbel
1 6
ORCID: ORCID

  1. Institute of Applied Physics, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
  2. Institute of Optoelectronics, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
  3. VIGO Photonics S.A., Poznańska 129/133, 05-850 Ożarów Mazowiecki, Poland
  4. Department of Electronics Fundamentals, Rzeszów University of Technology, W. Pola 12, 35-959 Rzeszów, Poland
  5. Institute of Computer and Information Systems, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
  6. Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw, Poland

Abstrakt

Mid-wavelength infrared detectors and focal plane array based on n-type InAs/InAsSb type-II strained layer superlattice absorbers have achieved excellent performance. In the long and very long wavelength infrared, however, n-type InAs/InAsSb type-II strained layer superlattice detectors are limited by their relatively small absorption coefficients and short growth-direction hole diffusion lengths, and consequently have only been able to achieve modest level of quantum efficiency. The authors present an overview of their progress in exploring complementary barrier infrared detectors that contain p-type InAs/InAsSb type-II strained layer superlattice absorbers for quantum efficiency enhancement. The authors describe some representative results, and also provide additional references for more in-depth discussions. Results on InAs/InAsSb type-II strained layer superlattice focal plane arrays for potential NASA applications are also briefly discussed.
Przejdź do artykułu

Autorzy i Afiliacje

David Z. Ting
1
Alexander Soibel
1
Arezou Khoshakhlagh
1
Sam A. Keo
1
Sir B. Rafol
1
Anita M. Fisher
1
Cory J. Hill
1
Brian J. Pepper
1
Yuki Maruyama
1
Sarath D. Gunapala
1

  1. NASA Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Dr., Pasadena, CA 91109-8099, USA

Abstrakt

As long as high resolution or long-range observation is to be achieved using infrared detection, it will be necessary to cool down the detector in order to reach the best sensitivity and dynamics. This paper describes different cooling solutions currently used for this purpose discussing advantages and drawbacks. Some guideline is given for cooler choice and selection. The focus is on rotary Stirling coolers illustrated by description of the RMs1 cooler dedicated to high operating temperature size, weight, and power infrared detectors. A user case study is presented with cooler power consumption and cool down time of the RMs1 cooler when integrated in IRnova’s Oden MW IDDCAs.
Przejdź do artykułu

Autorzy i Afiliacje

René Griot
1
Christophe Vasse
1
Roel Arts
2
Ruslan Ivanov
3
Linda Höglund
3
Eric Costard 
3

  1. Thales LAS France, 4 rue Marcel Doret, 31700 Blagnac, France
  2. Thales Cryogenics bv, Hooge Zijde 14, 5626 DC Eindhoven, The Netherlands
  3.  IRnova, Isafjordsgatan 26, SE-164 40 Kista, Sweden

Abstrakt

Careful selection of the physical model of the material for a specific doping and selected operating temperatures is a non-trivial task. In numerical simulations that optimize practical devices such as detectors or lasers architecture, this challenge can be very difficult. However, even for such a well-known material as a 5 µm thick layer of indium arsenide on a semi-insulating gallium arsenide substrate, choosing a realistic set of band structure parameters for valence bands is remarkable. Here, the authors test the applicability range of various models of the valence band geometry, using a series of InAs samples with varying levels of p-type doping. Carefully prepared and pretested the van der Pauw geometry samples have been used for magneto-transport data acquisition in the 20–300 K temperature range and magnetic fields up to ±15 T, combined with a mobility spectra analysis. It was shown that in a degenerate statistic regime, temperature trends of mobility for heavy- and light-holes are uncorrelated. It has also been shown that parameters of the valence band effective masses with warping effect inclusion should be used for selected acceptor dopant levels and range of temperatures.
Przejdź do artykułu

Autorzy i Afiliacje

Jarosław Wróbel
1
ORCID: ORCID
Gilberto A. Umana-Membreno
2
ORCID: ORCID
Jacek Boguski
1
ORCID: ORCID
Sebastian Złotnik
1
ORCID: ORCID
Andrzej Kowalewski
1
ORCID: ORCID
Paweł Moszczyński
3
ORCID: ORCID
Jarek Antoszewski
2
ORCID: ORCID
Lorenzo Faraone
2
Jerzy Wróbel
1 4
ORCID: ORCID

  1.  Institute of Applied Physics, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
  2. Dept. of Electrical, Electronic and Computer Engineering, The University of Western Australia, 35 Stirling Highway, Crawley WA 6009, Australia
  3. Faculty of Cybernetics, Military University of Technology, gen. Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland
  4. Institute of Physics, Polish Academy of Sciences, Aleja Lotników 32/46, 02-668 Warsaw, Poland

Abstrakt

Ga-free InAs/InAsSb type-II superlattice structures grown on GaSb substrates have demonstrated high performance for mid-wave infrared applications. However, realisation of long wavelength infrared photodetectors based on this material system still presents challenges, especially in terms of reduced quantum efficiency. This reduction is due, in part, to the increased type-II superlattice period required to attain longer wavelengths, as thicker periods decrease the wave-function overlap for the spatially separated quantum wells. One way to improve long wavelength infrared performance is to modify the type-II superlattice designs with a shorter superlattice period for a given wavelength, thereby increasing the wave-function overlap and the resulting optical absorption. Long wavelength infrared epitaxial structures with reduced periods have been realised by shifting the lattice constant of the type-II superlattice from GaSb to AlSb. Alternatively, epitaxial growth on substrates with orientations different than the traditional (100) surface presents another way for superlattice period reduction. In this work, the authors evaluate the performance of long wavelength infrared type-II superlattice detectors grown by molecular beam epitaxy using two different approaches to reduce the superlattice period: first, a metamorphic buffer to target the AlSb lattice parameter, and second, structures lattices matched to GaSb using substrates with different orientations. The use of the metamorphic buffer enabled a ~30% reduction in the superlattice period compared to reference baseline structures, maintaining a high quantum efficiency, but with the elevated dark current related to defects generated in the metamorphic buffer. Red-shift in a cut-off wavelength obtained from growths on high-index substrates offers a potential path to improve the infrared photodetector characteristics. Focal plane arrays were fabricated on (100), (311)A- and (211)B-oriented structures to compare the performance of each approach.
Przejdź do artykułu

Autorzy i Afiliacje

Dmitri Lubyshev
1
Joel M. Fastenau
1
Michael Kattner
1
Philip Frey
1
Scott A. Nelson
1
Ryan Flick
1
Ying Wu
1
Amy W. K. Liu
1
Dennis E. Szymanski
1
Becky Martinez
2
Mark J. Furlong
2
Richard Dennis
3
Jason Bundas
3
Mani Sundaram
3

  1. IQE, Inc., 119 Technology Dr., Bethlehem, PA 18015, USA
  2. IQE, Pascal Close, St. Mellons, Cardiff, CF3 0LW, UK
  3. QmagiQ, LCC, 22 Cotton Rd., Unit H, Suite 180, Nashua, NH 03063, USA

Abstrakt

The hyperspectral thermal imaging instrument for technology demonstration funded by NASA’s Earth Science Technology Office under the In-Space Validation of Earth Science Technologies program requires focal plane array with reasonably good performance at a low cost. The instrument is designed to fit in a 6U CubeSat platform for a low-Earth orbit. It will collect data on hydrological parameters and Earth surface temperature for agricultural remote sensing. The long wavelength infrared type-II strain layer superlattices barrier infrared detector focal plane array is chosen for this mission. With the driving requirement dictated by the power consumption of the cryocooler and signal-noise-ratio, cut-off wavelengths and dark current are utilized to model instrument operating temperature. Many focal plane arrays are fabricated and characterised, and the best performing focal plane array that fulfils the requirements is selected. The spectral band, dark current and 8–9.4 m pass band quantum efficiency of the candidate focal plane array are: 8–10.7 m, 2.1∙10−5 A/cm2, and 47%, respectively. The corresponding noise equivalent difference temperature and operability are 30 mK and 99.7%, respectively. Anti-reflective coating is deposited on the focal plane array surface to enhance the quantum efficiency and to reduce the interference pattern due to an absorption layer parallel surfaces cladding material.
Przejdź do artykułu

Autorzy i Afiliacje

Sir B. Rafol
1
Sarath D. Gunapala
1
David Z. Ting 
1
Alexander Soibel
1
Arezou Khoshakhlagh
1
Sam A. Keo
1
Brian J. Pepper 
1
Cory J. Hill
1
Yuki Maruyama
1
Anita M. Fisher 
1
Ashok Sood
2
John Zeller 
2
Robert Wright
3
Paul Lucey
3
Miguel Nunes
3
Luke Flynn
3
Sachidananda Babu
4
Parminder Ghuman
4

  1. Center for Infrared Photodetectors, Jet Propulsion Laboratory, California Institute of Technology Pasadena, California, USA
  2. Magnolia Optical Technologies, Inc, Albany New York 12203, USA
  3. Hawai'i Institute of Geophysics and Planetology, University of Hawai'i at Manoa, Honolulu, Hawaii, USA
  4. NASA Earth Science Technology Office Greenbelt, Maryland, USA

Abstrakt

Infrared detector technologies engineered from III-V semiconductors such as strained-layer superlattice, quantum well infrared photodetectors, and quantum dot infrared photodetectors provide additional flexibility to engineer bandgap or spectral response cut-offs compared to the historical high-performance detector technology of mercury/cadmium/telluride. The choice of detector cut-off depends upon the sensing application for which the system engineer is attempting to maximize performance within an expected ensemble of operational scenarios that define objects or targets to be detected against specific environmental backgrounds and atmospheric conditions. Sensor performance is typically characterised via one or more metrics that can be modelled or measured experimentally. In this paper, the authors will explore the impact of detector cut-off wavelength with respect to different performance metrics such as noise equivalent temperature difference and expected target detection or identification ranges using analytical models developed for several representative sensing applications encompassing a variety of terrestrial atmospheric conditions in the mid-wave and long-wave infrared wavelength bands. The authors will also report on their review of recently published literature concerning the relationships between cut-off wavelength and the other detector performance characteristics such as quantum efficiency or dark current for a variety of detector technologies.
Przejdź do artykułu

Autorzy i Afiliacje

Jonathan Ch. James
1
ORCID: ORCID
Terence L. Haran
1
Sarah E. Lane
1

  1. Electro-Optical Systems Laboratory, Georgia Tech Research Institute, 925 Dalney St. NW, Atlanta, GA 30332, USA

Abstrakt

The authors report two approaches, the first based on growth of lattice matched InGaAs/GaAsSb superlattice on InP substrate with tunable bandgap in the 2 to 3 µm range. The second approach is based on bulk random alloy InGaAsSb, which is tunable from 1.7 µm to 4.5 µm and lattice matched to the GaSb lattice constant. In each case, detector structures were fabricated and characterised. The authors have assessed the performance of these materials relative to commercially available extended short wave infrared devices through comparison to IGA-Rule 17 dark current performance level. A complementary barrier structure used in the InGaAsSb design showed improved quantum efficiency. The materials compare favourably to commercial technology and present additional options to address the challenging extended short wave infrared spectral band.
Przejdź do artykułu

Autorzy i Afiliacje

Everett D. Fraser
1
Jiayi Shao
1
Paul W. Frensley
1
Beau D. Barnes
1
Kevin P. Clark
1
Yung-Chung Kao
1
Paul R. Pinsukanjana
1

  1. Intelligent Epitaxy Technology, Inc. 1250 E. Collins Blvd., Richardson, TX 75081, USA

Instrukcja dla autorów

Guide for Authors

https://www.editorialsystem.com/opelre/journal/for_authors/

OPTO-ELECTRONICS REVIEW is an open access journal. This involves the payment of an article publishing charge (APC) by the authors, their institution or funding body. We make the article freely available immediately upon publication on PAS Jornals platform (https://journals.pan.pl/opelre)

As of July 1st, 2024, there are changes in the fees for open access publications in Opto-Electronics Review: 2000 PLN (500 EUR) - up to 8 pages of the journal format and mandatory over-length charges of 200 PLN (50 EUR) per page (see the above link with instructions for Authors for details)

Articles submitted by June 30th, 2024: existing fee: 1750 PLN (or 400 EUR)

Articles submitted from July 1st, 2024: new fee: 2000 PLN (or 500 EUR) - a flat fee per paper up to 8 pages of the journal format (each additional page will be charged an additional 200 PLN or 50 EUR).

Dodatkowe informacje

Opto-Electronics Review was established in 1992 for the publication of scientific papers concerning optoelectronics and photonics materials, system and signal processing. This journal covers the whole field of theory, experimental verification, techniques and instrumentation and brings together, within one journal, contributions from a wide range of disciplines. Papers covering novel topics extending the frontiers in optoelectronics and photonics are very encouraged. The main goal of this magazine is promotion of papers presented by European scientific teams, especially those submitted by important team from Central and Eastern Europe. However, contributions from other parts of the world are by no means excluded.

Articles are published in OPELRE in the following categories:

-invited reviews presenting the current state of the knowledge,

-specialized topics at the forefront of optoelectronics and photonics and their applications,

-refereed research contributions reporting on original scientific or technological achievements,

-conference papers printed in normal issues as invited or contributed papers.

Authors of review papers are encouraged to write articles of relevance to a wide readership including both those established in this field of research and non-specialists working in related areas. Papers considered as “letters” are not published in OPELRE.

Opto-Electronics Review is published quarterly as a journal of the Association of Polish Electrical Engineers (SEP) and Polish Academy of Sciences (PAS) in cooperation with the Military University of Technology and under the auspices of the Polish Optoelectronics Committee of SEP.

Abstracting and Indexing:

Arianta

BazTech

EBSCO relevant databases

EBSCO Discovery Service

SCOPUS relevant databases

ProQuest relevant databases

Clarivate Analytics relevant databases

WangFang

additionally:

ProQuesta (Ex Libris, Ulrich, Summon)

Google Scholar

Policies and ethics:

The editors of the journal place particular emphasis on compliance with the following principles:

Ethical policy of Opto-Electronics Review

The ethical policy of Opto-Electronics Review follows the European Code of Conduct for Research Integrity and is also guided by the core practices and policies outlined by the Committee on Publication Ethics (COPE).

Authors must be honest in presenting their results and conclusions of their research. Research misconduct is harmful for knowledge.

Research results

Fabrication, falsification, or selective reporting of data with the intent to mislead or deceive is unethical, as is the theft of data or research results from others. The results of research should be recorded and maintained to allow for analysis and review. Following publication, the data should be retained for a reasonable period and made available upon request. Exceptions may be appropriate in certain circumstances to preserve privacy, to assure patent protection, or for similar reasons.

Authorship

All those who have made a significant contribution should be given chance to be cited as authors. Other individuals who have contributed to the work should be acknowledged. Articles should include a full list of the current institutional affiliations of all authors, both academic and corporate.

Competing interests

All authors, referees and editors must declare any conflicting or competing interests relating to a given article. Competing interests through their potential influence on behavior or content or perception may undermine the objectivity, integrity, or perceived value of publication.

Peer Review

We are committed to prompt evaluation and publication of fully accepted papers in Opto-Electronics Review’s publications. To maintain a high-quality publication, all submissions undergo a rigorous review process.

Characteristics of the peer review process are as follows:

• Simultaneous submissions of the same manuscript to different journals will not be tolerated.

• Manuscripts with contents outside the scope will not be considered for review.

• Opto-Electronics Review is a single-blind review journal.

• Papers will be refereed by at least 2 experts as suggested by the editorial board.

• In addition, Editors will have the option of seeking additional reviews when needed. Authors will be informed when Editors decide further review is required.

• All publication decisions are made by the journal’s Editor-in-Chief based on the referees’ reports. Authors of papers that are not accepted are notified promptly.

• All submitted manuscripts are treated as confidential documents. We expect reviewers to treat manuscripts as confidential material.

• Editors and reviewers involved in the review process should disclose conflicts of interest resulting from direct competitive, collaborative, or other relationships with any of the authors, and remove oneself from cases in which such conflicts preclude an objective evaluation. Privileged information or ideas that are obtained through peer review must not be used for competitive gain.

• A reviewer should be alert to potential ethical issues in the paper and should bring these to the attention of the editor, including any substantial similarity or overlap between the manuscript under consideration and any other published paper of which the reviewer has personal knowledge. Any statement, observation, derivation, or argument that had been previously reported should be accompanied by the relevant citation.

• Personal criticism is inappropriate.

Plagiarism

Reproducing text from other papers without properly crediting the source (plagiarism) or producing many papers with almost the same content by the same authors (self-plagiarism) is not acceptable. Submitting the same results to more than one journal concurrently is unethical. Exceptions are the review articles. Authors may not present results obtained by others as if they were their own. Authors should acknowledge the work of others used in their research and cite publications that have influenced the direction and course of their study.

Plagiarism is not tolerated. All manuscripts submitted to Opto-Electronics Review will be checked for plagiarism (copying text or results from other sources) and self-plagiarism (duplicating substantial parts of authors’ own published work without giving the appropriate references) using the CrossCheck database (iThenticate plagiarism checker).

Duplicate submission

Simultaneous submissions of the same manuscript to different journals will not be tolerated. The submitted article will be removed without consideration.

Corrections and retractions

All authors have an obligation to inform and cooperate with journal editors to provide prompt retractions or correction of errors in published works.

• The journal will issue retractions if:

• There is clear evidence that the findings are unreliable, either as a result of misconduct (e.g., data fabrication or honest error - miscalculation or experimental error);

• The findings have previously been published elsewhere without proper cross-referencing, permission or justification (i.e., cases of redundant publication);

• It constitutes plagiarism;

• It reports unethical research.

• The journal will issue errata, if:

• A small portion of an otherwise reliable publication proves to be misleading (especially because of honest error);

• The author list is incorrect.

Other forms of misconduct include failure to meet clear ethical and legal requirements such as misrepresentation of interests, breach of confidentiality, lack of informed consent and abuse of research subjects or materials. Misconduct also includes improper dealing with infringements, such as attempts to cover up misconduct and reprisals on whistleblowers.

The primary responsibility for handling research misconduct is in the hands of those who employ the researchers. If a possible misconduct is brought to our attention, we will seek advice from the referees and the Editorial Board. If there is the evidence, we will resolve the matter by appropriate corrections in the printed and online journal; by refusing to consider an author's future work and by contacting affected authors and editors of other journals.

Human and Animal Rights

If the work involves the use of human subjects, the author should ensure that the work described has been carried out in accordance with The Code of Ethics of the World Medical Association (Declaration of Helsinki) for experiments involving humans; Uniform Requirements for manuscripts submitted to Biomedical journals. Authors should include a statement in the manuscript that informed consent was obtained for experimentation with human subjects. The privacy rights of human subjects must always be observed.

All animal experiments should comply with the ARRIVE guidelines and should be carried out in accordance with the EU Directive 2010/63/EU for animal experiments, and the authors should clearly indicate in the manuscript that such guidelines have been followed.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji